DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
D1U86P-W-1600-12-HBxDC Series 86mm 1U Front End AC-DC Power Supply D1U86P-W-1600-12-HBxDC.A01 Page 1 of 6 www.murata-ps.com/support www.murata-ps.com For full details go to www.murata-ps.com/rohs Ḥ ORDERING GUIDE Part Number Power Output; AC Line Main Output Standby Output Airflow(90-264V) (108-264V) (180-264V) D1U86P-W-1600-12-HB4DC 1200W 1350W 1600W 12V 12V Back to front D1U86P-W-1600-12-HB3DC Front to Back INPUT CHARACTERISTICS Parameter Conditions Min. Nom. Max. Units Input Voltage Operating Range 90 115/230 264 Vac Frequency 47 50/60 63 Hz Turn-on Voltage Ramp up 81 89 VacTurn-off Voltage Ramp down 70.5 73 78 Maximum Input Current 1200W, 100Vac 14.1 Arms Inrush Current At 264Vac at 25°C cold start 35 Apk Power Factor At 230Vac, half load 0.98 Efficiency (230Vac) excluding fan load 20% load 90 %50% load 94 100% load 91 OUTPUT VOLTAGE CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units 12V Droop 3.10 mV/A Ripple Voltage & Noise 1 20MHz Bandwidth 120 mV p-p Output Current (230 Vac) 2 0 133.4 A Output Current (120 Vac) 2 0 112.5 A Output Current (100 Vac) 2 0 100.0 A Load Capacitance 10,000 μF 12VSB Voltage Set Point 50% load 11.97 12.0 12.02 Vdc Ripple Voltage & Noise 1 20MHz Bandwidth 120 mV p-p Output Current 0 2.5 A 1 Ripple and noise measured with a parallel combination of a 1.0μF ceramic and 10μF tantalum capacitor on each of the power modu le outputs. A short coaxial cable connected directly to the input of a scope is required. 2 To meet ripple and transient step load specifi cations a minimum load of 4A is required.
FEATURES
1600W output power 94% minimum effi ciency at 50% load 12V main output 12V standby output of 30W 1U height: 3.4" x 7.75" x 1.59" 38.6 Watts per cubic inch density N+1 redundancy, including hot plugging (up to 8 in parallel) Current sharing on 12V main output Overvoltage, overcurrent, overtemperature protection Internal cooling fan (variable speed) PMBus™ / I²C interface monitoring and control RoHS compliant PRODUCT OVERVIEW The D1U86P-W-1600-12-HBxDC products are high efficiency 1600 watt, power factor corrected front end supplies with a 12V main output and a 12V (30W) standby. They have current sharing and up to 8 supplies may be operated in parallel. The supplies may be hot plugged, they recover from overtemperature faults, and have logic and PMBus monitoring and control. Their low profile 1U package and >38.6W/cubic inch power density make them ideal for delivering reliable, efficient power to servers, workstations, storage systems and other 12V distributed power systems. CB Test Certifi cate and Test Report www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html Available now at http://power.murata.com/en/3d/acdc.html
D1U86P-W-1600-12-HBxDC Series 86mm 1U Front End AC-DC Power Supply D1U86P-W-1600-12-HBxDC.A01 Page 2 of 6 www.murata-ps.com/support OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Output Rise Monotonicity No voltage excursion Startup Time AC ramp up 1.5 3 s Transient Response 12V, 50% load step, 1.0Aμs di/dt 600 mV12VSB, 50% load step,1.0Aμs di/dt 600 Current sharing accuracy (up to 8 in parallel)
3 At 100% load ±5 %
Hot Swap Transients All outputs remain in regulation 5 % Holdup Time At full load 12 ms 3 Load current of 100% applies to each power module max load connected in an N+1 confi guration; therefore the total load will be “N” x 100% . The share accuracy of ±5% is a fi xed percentage irrespective of total loading and number of units connected in parallel. ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range -40 85 °COperating Temperature Range 05 5 Operating Humidity Noncondensing 5 90 %Storage Humidity 59 5 Altitude (without derating at 45°C) 3000 m Shock 30G non operating Vibration 10-500Hz, 0.5G (non-operational) MTBF Per Telcordia SR-322 M1C1@ 40°C 559K hrs Acoustic 65 dBA/@1m Safety Approvals CSA 60950-1-07+A1:2011 ANSI/UL 60950-1-2011, Second Edition IEC 60950-1:2005 (2nd Edition) + A1:2009 EN 60950-1:2006 +A11:2009 +A1:2010 Input Fuse Power Supply has internal 16A/250V fast blow fuse on the AC line input Weight 2.33/1.06 lbs/Kg PROTECTION CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units Overtemperature (intake) An OTP warning will be issued via the PMBus™ interface when the air inlet exceeds 65°C; however the power module shall not shut down until critical internal hotspot temperatures are exceeded. 65 °C 12V Overvoltage Latching 13.2 14.4 V Overcurrent at 220Vac Shutdown of the output followed by auto- recovery after one second. The output shall attempt three such auto-recovery attempts and then enter a per- manent latched state. Recovery of the permanent latched state shall require cycling of the incoming AC source or toggling of the PSON# signal. 140 153 A Overcurrent at 120Vac 118 129 12VSB Overvoltage Latching 13.2 14.4 V Overcurrent Autorecovery 2.75 3 A ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Insulation Safety Rating / Test Voltage Input to Output - Reinforced 3000 Vrms Input to Chassis - Basic 1500 Vrms Isolation Output to Chassis 500 Vdc Leakage Current 1.5mA at 264Vac, 50/60Hz
D1U86P-W-1600-12-HBxDC Series 86mm 1U Front End AC-DC Power Supply D1U86P-W-1600-12-HBxDC.A01 Page 3 of 6 www.murata-ps.com/support STATUS INDICATORS AND CONTROL SIGNALS Signal Description PSON# Low = main output on; PSON# can be permanently tied to GND within the host system. PRESENT# Short pin pulled down on p/s; pulled up to either 3.3V or 12V (max) in the host system. For 3.3V use a 5.11KΩ resistor; for 12V , use a 21KΩ resistor. PS INTERRUPT Open drain PMBus™ signal; can be left open if not used. ADDR PMBus™ Address; ADDR can be grounded or left open if not used. If grounded, the address will be 000, if it is open, the default address will be 111. ISHARE Analog representation of main output current; can be left open if not used. PSOK4 A three level signal based on AC input and DC output status; can be left open if not used. I2C CLOCK I 2C clock I2C DATA I 2C data LED State Mode Operating Condition 1. Off AC Turn-off AC Input is below minimum power-supply turn-on specification 2. Green – blinking 1Hz Standby Power supply standby output is operating within normal parameters and main output is disabled 3. Green – solid Power-good Power supply standby & main outputs are operating within normal parameters and delivering power 4. Yellow – blinking 1Hz Warning Warning condition in power supply has been detected 5. Yellow – solid Fault Fault condition in power supply has been detected. 3 See truth table below for operation . OUTPUT CONNECTOR AND SIGNAL SPECIFICATION EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics IEC/EN 61000-3-2 Complies Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Complies Conducted Emissions FCC 47 CFR Part 15/CISPR 22/EN55022 Class A, 6dB margin ESD Immunity IEC/EN 61000-4-2 Level 3 criteria A Radiated Field Immunity IEC/EN 61000-4-3 Level 3 criteria B Electrical Fast Transient Immunity IEC/EN 61000-4-4 Level 3 criteria A Surge Immunity IEC/EN 61000-4-5 Level 3 criteria A Radiated Field Conducted Immunity IEC/EN 61000-4-6 Level 3 criteria A Magnetic Field Immunity IEC/EN 61000-4-8 3 A/m criteria B Voltage dips, interruptions IEC/EN 61000-4-11 230Vin, 100% load, Phase 0°, Dip 100% Duration 10ms (A) 230Vin, 50% load, Phase 0°, Dip 100% Duration 20ms (VSB:A, V1:A) 230Vin, 100% load, Phase 0°, Dip 100% Duration > 20ms (VSB, V1:B) Pin# Function Pin Type Description 14-26, 39-51 RTN Power Ground Power and Standby Return 1-13, 52-64 12V Power 12V Output 37 12VSB Power 12V Standby Output
38 PSINTERRUPT Output Active low; interrupt line for power supply
fault & warning detection as per PMBus spec
36 PRESENT# Input Power Supply Present Signal (shortest pin)
35 PSOK Analog output
Combination of there power supply output indicator signals: 1. AC input OK 2. Power Good 3. Power Supply Fault
34 ISHARE Analog I/O
Analog representation of main output current. Typical analog voltage shall be 60.15mV/Amp of main output current.
33 PSON# Input Power Supply on/off control signal
32 SCL Input SMBus/PMBus Clock
31 SDA I/O SMBus/PMBus Data
30 GND Analog I/O Power Supply Signal Ground
29 N/A N/A Reserved; no User connection
28 N/A N/A Reserved; no User connection
27 ADDR Analog input PMBus Address
Power Supply Output Card Edge PCB Top Side PCB Bottom Side 164 33 32
D1U86P-W-1600-12-HBxDC Series 86mm 1U Front End AC-DC Power Supply D1U86P-W-1600-12-HBxDC.A01 Page 4 of 6 www.murata-ps.com/support DERATING CURVES 100 120 140 25 30 35 40 45 50 55 Main Output current (Adc) Ambient Temperature (°C) 90V 120V 180V + Output Current Derating vs. Ambient Temperature (back to front airflow) D1U86P‐W‐1600‐HB4DC; VSB 1.0A 12Vdc @90Vac ‐ 113A to 45°C; derates to 90A at 50°C Main Output current (Adc) Ambient Temperature (°C) 100 120 140 25 30 35 40 45 50 55 90V 120V 180V+ Output Current Derating vs. Ambient Temperature (front to back airflow) D1U86P‐W‐1600‐12‐HB3DC; VSB 2.5A (No Derating) CONNECTOR AND SIGNAL SPECIFICATION4 PSOK TRUTH TABLE VS. ANALOG OUTPUT DC_OK_H PWR_GOOD_H PS_FAULT_L PSOK OPERATION MODE 0 0 1 < 0.1Vdc VDD = 3.3Vdc No DC Input 0 1 1 (1/3) VDD Invalid 1 0 1 (2/3) VDD Standby 1 1 1 VDD Power Good X X 0 0.2-0.4Vdc PS Fault
D1U86P-W-1600-12-HBxDC Series 86mm 1U Front End AC-DC Power Supply D1U86P-W-1600-12-HBxDC.A01 Page 5 of 6 www.murata-ps.com/support WIRING DIAGRAM FOR OUTPUT CURRENT SHARING NOTES Main Output: Current share is achieved using the droop method. Nominal output voltage (12.20V) is achieved at 50% load and output voltage droops at a rate of 3.10mv per amp increase. Startup of parallel power supplies is not internally synchronized. If more than 1600W combined power is needed, start-up synchroniza- tion must be provided by using a common PS_ON signal. To account for ±5% full load current sharing accuracy and the reduction in full load output voltage due to droop, available output power must be derated by 10% when units are operated in parallel. Standby output can be tied together for redundancy but total combined output power must not exceed 30W, Internal MOSFET ORING devices are used D1U86 D1U86 PSON# PSON# FET,BJT,wire or switch (debounced) to turn on 12V main output FET,BJT,wire or switch (debounced) to turn on 12V main output RTN RTN RTN RTN 14-26, 39-51 14-26, 39-51 12VSB 12VSB 37 37 33 33 Main output load VSB load
D1U86P-W-1600-12-HBxDC Series 86mm 1U Front End AC-DC Power Supply D1U86P-W-1600-12-HBxDC.A01 Page 6 of 6 www.murata-ps.com/support Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi cations are subject to change without notice. © 2015 Murata Power Solutions, Inc. Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfi eld, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ MECHANICAL DIMENSIONS MATING CONNECTOR Part Number Description FCI 10053363-200LF Right Angle FCI 10046971-001LF Vertical OPTIONAL ACCESSORIES Description Part Number 12V D1U86P Output Connector Card D1U86P-12-CONC APPLICATION NOTES Document Number Description ACAN-50 D1U86P Output Connector Card ACAN-51 D1U86P Communication Protocol AC input connector: IEC 320-C14 191.70±0.50 0.062" AIR FLOW DIRECTION FRONT TO BACK AIR FLOW DIRECTION BACK TO FRONT 2X3.20±0.25 83.52±0.30
240.75 REF
190.90±0.65 8.00±0.30 3.30±0.25 51.36±0.30 9.00±0.30 39.90±0.50 3.00±0.25 197.70±0.65 137.70 REF 16.50±0.30