FBR53-HW FCL | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 7
Technical content
1 POLE - 40A (For automotive applications)
˙ FEATURES w Small 40A relay w High temperature grade (-40˚C to 125˚C) w Contact arrangement Form U (form A) w Surface mount compatible (reflow capability) w Inrush current 80A w Coil wire temperature class: H ˙ Part Numbers [Example] ɹFBR53 N D12 - Y - HW - RW (a) (b) (c) (d) (e) (f) (a) Relay type FBR53 : FBR53 series (b) Enclosure N : Plastic sealed type (c) Coil rated voltage D12 : 9...12VDC Coil rating table at page 3 (d) Contact material Y : Silver-tin oxide (e) Contact rating HW : 40A (f) Soldering Nil RW : Standard (Flow soldering) : Reflow capable (THR) Actual markings does not carry the type name: "FBR" E.g.: Ordering code: FBR53ND12-Y-HW Actual marking: 53ND12-Y-HW
■ Specifications Item FBR53-HW Remarks / conditions Contact data Configuration 1 form U Material Silver-tin oxide Voltage drop Max. 100 mV at 1A, 12VDC. Average 1.2mΩ at 7A, 12VDC Contact rating 40A, 14VDC Resistive load Max. carrying current 40A Max. inrush current 80A Reference Min. switching load 1A 6VDC Reference * Coil Rated power consumption 860mW At 20ºC Operate power consumption 310mW At 20ºC Operating temperature range -40ºC ~ +125ºC No frost Timing data Operate Max. 10ms At nominal voltage Release Max. 10ms At nominal voltage Life Mechanical Min. 1 x 10⁶ operations without contact load Electrical Min. 100 x 10³ operations 14VDC, 40A resistive load Insula- tion Insulation resistance Min. 100MΩ Initial Dielectric withstanding voltage Open con- tacts 500VAC (50/60Hz), 1 minute Coil contact 500VAC (50/60Hz), 1 minute Other Vibration resistance Misoperation 10 to 200Hz, acceleration 44m/s2(4.4G) constant acceleration Endurance 10 to 200Hz, acceleration 44m/s2(4.4G) constant acceleration Shock resistance Misoperation 100m/s² (11±1ms) Direction X, Y, Z, contact ON/OFF total 36 times Endurance 1,000m/s² (6±1ms) Direction X, Y, Z, contact OFF total 18 times Dimensions / weight 12.3 x15.7x14.0 mm / approx. 6g *: Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. Care shall be taken on the heat generated on PC board when maximum carrying current exceeds 10A. Please perform the confirmation test with actual conditions.
˙ Coil Data Coil code Rated Coil Voltage (VDC) Coil Resistance +/-10%(Ω) Must Operate Voltage* (VDC) Must Release Voltage* (VDC) D09 9 94 5.4 7.7 (at 125ºC) 0.7 1.0 (at 125ºC) D10 10 117 6.3 9 (at 125ºC) 0.8 1.2 (at 125ºC) D12 12 167 7.3 10.4 (at 125ºC) 1.0 1.5 (at 125ºC) Note: All values in the table are valid at 20oC and zero contact current, unless otherwise specified. *: Specified operated values are valid for pulse wave voltage. Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage. ˙ Dimensions w Dimensions Dimensions of the terminals do not include thickness of pre-solder. w Schematics (BOTTOM VIEW) Pattern shall be designed to short-circuit #4 and #5 on the PC board. COM terminal: 2.2 x 0.26 t Coil terminal: 1.0 x 0.3 t N.O. terminal: 2.2 x 0.4 t
w PC Board Mouting Hole Layout (BOTTOM VIEW) Tolerance of PC board mounting hole layout : ±0.1 unless otherwise specified. ( ): Reference value Unit: mm ˙ Characteristic Data (Reference) +0.12-2.5X0.6 +0.12-2.5X0.7 (1.25)10.62.5 1.3+0.1 -02-φ A B +0.10.6 2.5 (R) (R) +0.10.7 2.5 A B 0 10 20 30 40 50 60 70 80 100 FBR53ND10-Y-HW n=50 Release Release Operate Operate 0 1 2 3 4 5 6 7 8 9 10 100 FBR53ND10-Y-HW n=100 L,R n=100 FBR53ND10-Y-HW 100 80 70 60 50 40 30 20 10 0 at 6Vdc-1A Distribution of operate/relase voltage Distribution of operate/relase time Distribution of contact resistance Nominal voltage multiplying factor (%) Time (ms) Distribution (%) Distribution (%) Distribution (%) Contact resistance (mΩ)
Ambient temperature 25°C 10 20 30 40 50 70 100 100 1000 10000 -40 -20 0 20 40 60 80 100 120 FBR53ND10-Y-HW 40A 16V +125°C max.-40°C min. 40003000200010000 Contact current Ambient temperature/voltage Coil temperature rise (1) Carrying current (A) Carrying current (A) Switching voltage (V) Switching current (A) Ambient temperature (°C) Applied time (sec.) Coil temperature rise (°C) Coil temperature rise (°C) Coil voltage (V) Time (sec.) Ambient temperature 20ˆ Bus bar connection 2 contacts connected in parallel Allowable voltage Coil voltage: 16V Coil voltage: 12V Coil voltage: 8V FBR53ND10-Y-HW at 25°C, 0A 1 10 100 1000 100 1000 10 20 30 40 50 100 0.1 100 1000 FBR53ND10-Y-HW Coil temperature rise (2) Max. allowable switching 12V
- ROHS Compliance w All relays produced by FCL Components are compliant with RoHS directive 2011/65/EU, including commission delegated directive 2015/863. Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended lead free solder condition w w Recommended solder for assembly: Sn-3.0Ag-0.5Cu. 3. Moisture Sensitivity w Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers w Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. Flow Solder Condition: Pre-Heating: maximum 120˚C within 90 sec. Soldering: dip within 5 sec. at 255°C±5°C solder bath Reflow Solder Condition: (Applicable only for reflow capable type) Recommended reflow soldering profile IRS (infrated reflow soldering) Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron: 30-60W Temperature: maximum 340-360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions ɾ All values mentioned in this datasheet are provided under ideal conditions. Please perform the confirmation test before actual use. ɾ Reflow soldering is prohibited for flow soldering type. ɾ Do not use relays in the atmosphere with sulfide gas, chloride gas or nitric oxide. Contact resistance may increase. ɾ Do not use silicon or silicon-containing product or materials near relays. It may cause contact failure. 250 220 170 130Temperature (°C) Max.120 sec. 90 to 120 sec. 20 to 30 sec. Pre-heating Peak temperature: Max.250°C
Shinagawa Seaside Park Tower 12-4, Higashi-shinagawa 4-chome, Tokyo 140 0002, Japan Tel: +81-3-3450-1682 Email: fcl-contact@cs.fcl-components.com Asia Pacific Web: www.fcl-components.com/en/ Europe FCL COMPONENTS EUROPE B.V. Diamantlaan 25
2132 WV Hoofddorp, Netherlands
Tel: +31-23-556-0910 Email: info.fceu@cs.fcl-components.com FCL COMPONENTS ASIA PTE LTD. No. 20 Harbour Drive, #07-01B Singapore 117612 Tel: +65-6375-8560 Email: fcal@fcl-components.com North and South America FCL COMPONENTS AMERICA, INC.
2055 Gateway Place Suit e 480,
San Jose, CA 95110 USA Tel: +1-408-745-4900 Email: fcai.components@fcl-components.com China FCL COMPONENTS (SHANGHAI) CO., LTD. Unit 1105, Central Park - Jing An, No.329 Heng Feng Road, Shanghai 200070, China Tel: +86-21-3253 0998 Email: fcsh@fcl-components.com © 2024 FCL Components Limited. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. FCL Products are intended for general use, including without limitation, in personal, household and office environments, in buildings and for ordinary use in the industry. FCL Products are not intended to be used in applications where extremely high safety is required (”High Safety Required Applications”), such as, but not limited to, applications in nuclear facilities, in aircraft automatic flight control, in air traffic control, in mass transit system control, in missile launch system, in weapon systems, in medical equipment for life support or any application involving a direct serious risk of physical injury or death. Please do not use FCL Products without securing the sufficient safety and reliability required for the High Safety Required Applications. In addition, FCL shall not be liable against the customer and/or any third party for any claims or damages arising in connection with the use of FCL Products in the High Safety Required Applications. FCL warrants that its Products, if properly used and services, will conform to their specification and will be free from defects in material and workmanship for twelve months from delivery. The implied warranties of merchantability and fitness for a particular purpose and all other warranties, representations and conditions, express or implied by statute, trade usage or otherwise, expect as set forth in this warranty, are excluded and shall not apply to the Products delivered. The contents, data and information in this datasheet are provided by FCL Components Limited as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. FCL has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, compre- hensive, complete and up to date. FCL Components Limited and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do FCL Components Limited and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. February 1, 2024.