FBR07HA121NB-00

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 18

Technical content

Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ˙ Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be- fore practical application or usage of the Products. Please note that TAIYO YUDEN CO., LTD. shall not be responsible for any defects in products or equipment incor- porating such products, which are caused under the conditions other than those specified in this catalog or indi- vidual specification. ˙ Please contact TAIYO YUDEN CO., LTD. for further details of product specifications as the individual specification is available. ˙ Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. ˙ All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact TAIYO YUDEN CO., LTD. for more detail in ad- vance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma- rine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil- ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. ˙ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu- tors (so called ʠTAIYO YUDENʟs official sales channelʡ). It is only applicable to the products purchased from any of TAIYO YUDENʟ s official sales channel. ˙ Please note that TAIYO YUDEN CO., LTD. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. TAIYO YUDEN CO., LTD. grants no license for such rights. ˙ Caution for export Certain items in this catalog may require specific procedures for export according to ʠForeign Exchange and For- eign Trade Control Lawʡ of Japan, ʠU.S. Export Administration Regulationsʡ, and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 115 NOISE SUPPRESSION COMPONENTS ／FERRITE BEAD INDUCTORS LEADED FERRITE BEAD INDUCTORS(FB SERIES A TYPE / R TYPE) WAVE i_leaded_FBA_FBR_e-E02R01 LEADED FERRITE BEAD INDUCTORS (FB SERIES A TYPE / R TYPE) ■PARTS NUMBER *Operating Temp. : -25～+85℃（Including self-generated heat） F B A 0 4 H A 4 5 0 B B － 0 0 △＝Blank space ① ② ③ ④ ⑤ ⑥ ⑦ ①Series name Code Series name FB Ferrite bead ②Shape Code Shape A Axial lead R Radial lead ③Dimensions of core（D） Code Dimensions of core（D）［mm］ 03 φ2.5 04 φ3.5 05 5.0 06 6.0 07 7.5 ④Material Code Material HA Refer to impedance curves for material differences VA ⑤Nominal impedance Code （example） Nominal impedance［Ω min.］ 850 85 121 120 Excluding 03type ⑥Lead configuration Code Lead configurations［ｍｍ］ AB Straight lead (26mm lead space) / ammo BB Straight lead (52mm lead space) / ammo KD Formed lead (10mm pitch) / bulk KE Formed lead (12.5mm pitch) / bulk KF Formed lead / bulk (15.0mm pitch) / bulk NA Lead (2.5mm pitch)/bulk (FBR) Straight lead / bulk (FBA) NB Formed lead (crimped) / bulk SA Straight lead (FBR05 type) / ammo SB Straight lead (FBR07 type) / ammo TB Straight lead (FBR07 type) / ammo UB Radial lead formed / ammo US Formed lead (crimped) / bulk VB Dual side lead formed (crimped) / ammo VS Formed lead / bulk ⑦Internal code Code Internal code －00 Standard ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 116 NOISE SUPPRESSION COMPONENTS ／FERRITE BEAD INDUCTORS i_leaded_FBA_FBR_e-E02R01 Unit：mm（inch） □Please specify the lead configuration code. Note: Lead diameter (φd) shall fall within a range of 0.65mm±0.05mm, FBR05, and FBR07 types however, will have a lead diameter (φd) range of 0.6mm±0.05mm. ■PARTS NUMBER

• FBA HA VA HA VA
• FBR HA VA HA VA FBR05VA121[]-00 RoHS 120.0 - 100 - 7.0 0.01 1.0 ※△Please specify material codes (HA,VA) and [] lead configuration code. Nominal impedance ［Ω］（min.） Rated current ［MΩ］（min.） Rated current ［MΩ］（min.） Rated current ［A］（max.） Material Parts number EHS Parts number EHS Nominal impedance ［Ω］（min.） Impedance measuring frequency ［MHｚ］ Impedance measuring frequency ［MHｚ］ Rated current ［A］（max.） lairetaMlairetaM DC Resistance ［Ω］（max.） DC Resistance ［Ω］（max.） Material

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-E02R01 LEADED FERRITE BEAD INDUCTORS ■PACKAGING ①Minimum Quantity

• Axial lead (FBA) Type Lead Configuration Standard quantity [pcs] Bulk Taped Ammo FBA03 NA, KD, US 1000 － KE, KF, VS 500 － AB, BB － 2000 UB, VB － 3000 FBA04 NA, KD, US 1000 － KE, KF, VS 500 － AB, BB － 1000 VB, UB － 3000
• Radial lead (FBR) Type Lead Configuration Standard quantity [pcs] Bulk Taped Ammo FBR05 NA 1000 － SA － 2000 FBR06 NA 1000 － FBR07 NB 1000 － SB － 2000 ②Bulk dimensions Axial lead (FBA)
• NA Type Dimensions φD L1 L2 φd ℓ FBA03□450 2.5±0.2 （0.098±0.008） 4.5±0.3 （0.177±0.012） 6.5 max. （0.256 max.） 0.65±0.05 （0.026±0.002） 18 min. （0.709 min.） FBA04□450 3.5±0.2 （0.138±0.008） 4.5±0.3 （0.177±0.012） 6.5 max. （0.256 max.） FBA04□600 3.5±0.2 （0.138±0.008） 6.0＋0.5/－0 （0.236＋0.020/－0） 8.5 max. （0.335 max.） FBA04□900 3.5±0.2 （0.138±0.008） 9.0±0.5 （0.354±0.020） 11.0 max. （0.433 max.） Unit：mm（inch）
• US Type Dimensions φD A a F φd FBA03□450 2.5±0.2 （0.098±0.008） 4.5±0.3 （0.177±0.012） 9.0 max. （0.197±0.039） 0.65±0.05 （0.138±0.008） 4.5±0.3 （0.177±0.012） 9.0 max. （0.354 max.） Unit：mm（inch）

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-E02R01

• KD/KE/KF Type Lead Symbol Dimensions φD F L1 φd ℓ FBA03□450 KD 2.5±0.2 （0.098±0.008） 10.0±1.0 （0.394±0.039） 4.5±0.3 （0.177±0.012） 0.65±0.05 （0.026±0.020） 7.0±2.0 （0.276±0.079） FBA04□450 3.5±0.2 （0.138±0.008） 10.0±1.0 （0.394±0.039） 4.5±0.3 （0.177±0.012） 7.5±2.0 （0.295±0.079） FBA04□600 3.5±0.2 （0.138±0.008） 10.0±1.0 （0.394±0.039） 6.0＋0.5/－0 （0.236＋0.020/－0） 7.5±2.0 （0.295±0.079） FBA03□450 KE 2.5±0.2 （0.098±0.008） 12.5±1.0 （0.492±0.039） 4.5±0.3 （0.177±0.012） 0.65±0.05 （0.026±0.020） 7.0±2.0 （0.276±0.079） FBA04□450 3.5±0.2 （0.138±0.008） 12.5±1.0 （0.492±0.039） 4.5±0.3 （0.177±0.012） 7.5±2.0 （0.295±0.079） FBA04□600 3.5±0.2 （0.138±0.008） 12.5±1.0 （0.492±0.039） 6.0＋0.5/－0 （0.236＋0.020/－0） 7.5±2.0 （0.295±0.079） FBA04□900 3.5±0.2 （0.138±0.008） 12.5±1.0 （0.492±0.039） 9.0±0.5 （0.354±0.020） 7.5±2.0 （0.295±0.079） FBA03□450 KF 2.5±0.2 （0.098±0.008） 15.0±1.0 （0.591±0.039） 4.5±0.3 （0.177±0.012） 0.65±0.05 （0.026±0.020） 7.0±2.0 （0.276±0.079） FBA04□450 3.5±0.2 （0.138±0.008） 15.0±1.0 （0.591±0.039） 4.5±0.3 （0.177±0.012） 7.5±2.0 （0.295±0.079） FBA04□600 3.5±0.2 （0.138±0.008） 15.0±1.0 （0.591±0.039） 6.0＋0.5/－0 （0.236＋0.020/－0） 7.5±2.0 （0.295±0.079） FBA04□900 3.5±0.2 （0.138±0.008） 15.0±1.0 （0.591±0.039） 9.0±0.5 （0.354±0.020） 7.5±2.0 （0.295±0.079） Unit：mm（inch）
• VS ※5±1 for 900 type only Type Dimensions φD A a F φd FBA03□450 2.5±0.2 （0.098±0.008） 4.5±0.3 （0.177±0.012） 12.5 max. （0.492 max.） 5.0±1.0 （0.197±0.039） 0.65±0.05 （0.026±0.002） FBA04□450 3.5±0.2 （0.138±0.008） 4.5±0.3 （0.177±0.012） 12.5 max. （0.492 max.） 5.0±1.0 （0.197±0.039） 0.65±0.05 （0.026±0.002） FBA04□600 3.5±0.2 （0.138±0.008） 6.0＋0.5/－0 （0.236＋0.020/－0） 12.5 max. （0.492 max.） 5.0±1.0 （0.197±0.039） 0.65±0.05 （0.026±0.002） FBA04□900 3.5±0.2 （0.138±0.008） 9.0±0.5 （0.354±0.020） 16.0 max. （0.630 max.） 5.0±1.0 （0.197±0.039） 0.65±0.05 （0.026±0.002） Unit：mm（inch）

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-E02R01 Radial lead (FBR)

• NA Type Dimensions D L1 φd ℓ W F FBR05VA121 5.0 max. （0.197 max.） 9.0 max. （0.354 max.） 0.65±0.05 （0.026±0.002） 10.0＋3/－5 2.5 max. （0.098 max.） 2.5±1.0 （0.098±0.039） FBR06□850 6.0±0.5 （0.236±0.020） 7.0 max. （0.276 max.） 0.65±0.05 （0.026±0.002） 10.0＋3/－5 3.0±0.5 （0.118±0.020） 2.5±1.0 （0.098±0.039） FBR06□121 6.0±0.5 （0.236±0.020） 9.0 max. （0.354 max.） 0.65±0.05 （0.026±0.002） 10.0＋3/－5 3.0±0.5 （0.118±0.020） 2.5±1.0 （0.098±0.039） Unit：mm（inch）
• NB Type Dimensions D L1 φd ℓ W F FBR07□850 7.5±0.5 （0.295±0.020） 7.0 max. （0.276 max.） 0.6±0.05 （0.024±0.002） 5.0＋1/－2 2.5 max. （0.098 max.） 5.0＋1/－0.5 FBR07□121 7.5±0.5 （0.295±0.020） 9.0 max. （0.354 max.） 0.6±0.05 （0.024±0.002） 5.0＋1/－2 2.5 max. （0.098 max.） 5.0＋1/－0.5 Unit：mm（inch）

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-E02R01 ③Taping Dimensions

• AB（a: 26mm）（1.02inch lead space） Type Dimensions Minimum insertion pitch φD L a b |L1-L2| φd FBA03 2.5±0.2 （0.098±0.008） 4.5±0.3 （0.177±0.012） 26.0＋1.5/－0 （1.02＋0.059/－0） 0.8max （0.031max） 1.0 max （0.039 max） 0.65±0.05 （0.026±0.002） 10.0 （0.394） FBA04□450 3.5±0.2 （0.138±0.008） 4.5±0.3 （0.177±0.012） 26.0＋1.5/－0 （1.02＋0.059/－0） 0.8max （0.031max） 1.0 max （0.039 max） 0.65±0.05 （0.026±0.002） 10.0 （0.394） （0.236＋0.020/－0） 26.0＋1.5/－0 （1.02＋0.059/－0） 0.8max （0.031max） 1.0 max （0.039 max） 0.65±0.05 （0.026±0.002） 10.0 （0.394） FBA04□900 9.0±0.5 （0.354±0.020） 26.0＋1.5/－0 （1.02＋0.059/－0） 0.8max （0.031max） 1.0 max （0.039 max） 0.65±0.05 （0.026±0.002） 12.5 （0.492） Unit：mm（inch）
• BB（a: 52mm）（ 2.05inches lead space） Type Dimensions Minimum insertion pitch φD L a b |L1-L2| φd FBA03 2.5±0.2 （0.098±0.008） 4.5±0.3 （0.177±0.012） 52.0＋2/－1 1.2 max （0.047 max） 1.0 max （0.039 max） 0.65±0.05 （0.026±0.002） 10.0 （0.394） FBA04□450 3.5±0.2 （0.138±0.008） 4.5±0.3 （0.177±0.012） 52.0＋2/－1 1.2max （0.047max） 1.0 max （0.039 max） 0.65±0.05 （0.026±0.002） 10.0 （0.394） （0.236＋0.020/－0） 52.0＋2/－1 1.2max （0.047 max） 1.0 max （0.039 max） 0.65±0.05 （0.026±0.002） 10.0 （0.394） FBA04□900 9.0±0.5 （0.354±0.020） 52.0＋2/－1 1.2max （0.047 max） 1.0 max （0.039 max） 0.65±0.05 （0.026±0.002） 12.5 （0.492） Unit：mm（inch）

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-E02R01

• SA（F: 2.5mm pitch）（0.098 inches） Type Symbol Dimensions Symbol Dimensions Symbol Dimensions FBR05 A 121: 9.0 max. （0.039 max.） T 2.5 max. （0.157±0.012） D 5.0 max. （0.026±0.002） H 18.0＋2.0/－0 （0.433 max.） P 12.7±1.0 （0.028±0.008） P0 12.7±0.3 ※1 （0.354＋0.030/－0.020） Unit： mm（inch） P1 5.1±0.7 （0.118 max.） ※1 Accumulated error for 20 pitches is ±2mm. ※2 Bonding tape must not protrude from the base tape.
• SB/TB（F: 5mm pitch）（0.197 inches） Type Symbol Dimensions Symbol Dimensions Symbol Dimensions FBR07 A 121: 9.0 max. 850: 7.0 max. （0.118 max.） T 2.5 max. （0.039 max.） D 7.5±0.5 （0.157±0.012） H S B : 1 8 . 0 ＋ 2 . 0 / － 0 （0.02±0.002） T B : 1 6 . 0 ± 0 . 5 （0.433 max.） P 12.7±1.0 （0.028±0.008） Unit： mm（inch） ※1 Accumulated error for 20 pitches is ±2mm. ※2 Bonding tape must not protrude from the base tape.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-E02R01

• UB Type Symbol Dimensions Symbol Dimensions Symbol Dimensions FBA03□450 FBA04□450 A 4.5±0.3 （0.118 max.） A1 9.0 max. （0.039 max.） φD 0 3 : 2 . 7 m a x . （0.157±0.012） 0 4 : 3 . 7 m a x . （0.026±0.002） H 20.0＋0.5/－1.0 （0.433 max.） P 12.7±1.0 （0.028±0.008） P0 12.7±0.3 ※1 （0.354＋0.030/－0.020） Unit： mm（inch） ※1 Accumulated error for 20 pitches is ±2mm. ※2 Bonding tape must not protrude from the base tape.
• VB 形状 Type Symbol Dimensions Symbol Dimensions Symbol Dimensions FBA03□450 FBA04□450 FBA04□600 FBA04□900 A 450: 4.5±0.3 （0.177±0.012） P 0 12.7±0.3 ※1 （0.118 max.） 600: 6.0＋0.5/－0 （0.039 max.） 900: 9.0±0.5 （0.157±0.012） 450: 12.5 max. （0.026±0.002） 900: 16.0 max. （0.433 max.） φD 3.7 max. （0.028±0.008） H0 16.0±0.5 （0.492 min. ） Unit： mm（inch） P 12.7±1.0 ※1 Accumulated error for 20 pitches is ±2mm. ※2 Bonding tape must not protrude from the base tape.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 AXIAL LEADED INDUCTORS（CAL Type）、 RADIAL LEADED INDUCTORS（LH Type）、 LEADED FERRITE BEAD INDUCTORS（ FB Series A Type／R Type） ■RELIABILITY DATA 1. Operating temperature Range Specified Value CAL45 Type －25～＋ 105℃ LHL□□□ FBA/FBR －25～＋ 85℃ Test Methods and Remarks CAL45 Type : Including self-generated heat LHL□□□ : Including se lf-generated heat 2. Storage temperature Range Specified Value CAL45 Type FBA/FBR 3. Rated current Specified Value CAL45 Type Within the specified tolerance LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : The maximum DC value having inductance within 10% and temperature increase within 40℃ by the application of DC bias. LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the following specified temperature by the application of DC bias. Reference temperature : 25℃（LHL08, LHL10, LHL13） : 40℃（LHLC08, LHLC10） FBA/FBR : No disconnection or appearance abnormality by continuous curren t application for 30 min. Change after the application shall be within ±20% of the initial value. This is not guaranteed for electrical characteristics during current application. 4. Impedance Specified Value CAL45 Type LHL□□□ FBA/FBR Within the specified tolerance Test Methods and Remarks FBA/FBR : Measuring equipment : Impedance analyzer (HP4191A) or its equi valent Measuring frequency : Specified frequency 5. Inductance Specified Value CAL45 Type Within the specified tolerance LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent) Measuring frequency : Specified frequency LHL□□□ : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equiva lent) : LCR meter (HP4263A) or its equivalent (at 1kHz) Measuring frequency : Specified frequency

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 6. Q Specified Value CAL45 Type LHL□□□ Within the sp ecified tolerance FBA/FBR Test Methods and Remarks LHL□□□ (except LHLP) : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equiv alent) : LCR meter (HP4263A) or its equivalent (at 1kHz) Measuring frequency : Specified frequency 7. DC Resistance Specified Value CAL45 Type Within the specified tolerance LHL□□□ FBA/FBR Test Methods and Remarks Measuring equipment : DC ohmmeter 8. Self resonance frequency Specified Value CAL45 Type LHL□□□ Within the sp ecified tolerance FBA/FBR Test Methods and Remarks LHL□□□(except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent 9. Temperature characteristic Specified Value CAL45 Type LHL□□□ △L/L : Within ±7% (ex cept LHLP16 : Within ±20%) FBA/FBR Test Methods and Remarks Change of maximum inductance deviation in step 1 to 5 Step Temperature (℃) LHL□□□ 1 20

2 Minimum operating temperature

3 20 (Standard temperature)

4 Maximum operating temperature

1. Tensile strength test Specified Value CAL45 Type No abnormality such as cut lead, or looseness. LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Apply the stated tensile force progressively in the direction to draw terminal. force (N) duration (s) 10 10 LHL□□□ : Apply the stated tens ile force progressively in the direction to draw terminal. Nominal wire diameter tensile φd (mm) force (N) duration (s) 0.3＜φd≦0.5 5 30±5 0.5＜φd≦0.8 10 0.8＜φd≦1.2 25 FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the axi al direction of the component during 10±1 seconds.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 11. Over current Specified Value CAL45 Type No emission of smoke no firing. LHL□□□ There shall be no scorch or short of wire. LHLC08, LHLC10 : There shall be no firing. FBA/FBR Test Methods and Remarks Measuring current : Rated current×2 Duration : 5 min. Number of measuring : one time 12. Terminal strength : bending Specified Value CAL45 Type No abnormality such as cut lead, or looseness. LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter tensile Bending force Mass reference weight LHL□□□・FBA/FBR : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter tensile Bending force Mass reference weight 0.5＜φd≦0.8 5 0.5 0.8＜φd≦1.2 10 1.0 13. Insulation resistance : between the terminals and body Specified Value CAL45 Type LHL□□□ 100MΩ min. FBA/FBR Test Methods and Remarks LHL□□□ : Applied voltage : 500 VDC Duration : 60 sec. 14. Insulation resistance : between terminals and core Specified Value CAL45 Type LHL□□□ FBA/FBR 1MΩ min. Test Methods and Remarks FBA/FBR : Applied voltage : 100 VDC Duration : 60±5 sec. 15. Withstanding : between the terminals and body Specified Value CAL45 Type LHL□□□ No abnormality such as insulation damage FBA/FBR Test Methods and Remarks LHL□□□ : According to JIS C5102. 7. 1. 3 (C) Metal global method Applied voltage : 500 VDC Duration : 60 sec.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 16. DC bias characteristic Specified Value CAL45 Type △L/L : Within －10% LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Measure inductance with application of rated current using LCR meter to compare it with the initial value. 17. Body strength Specified Value CAL45 Type No abnormality as damage. LHL□□□ FBA/FBR No abnormality such as cracks on body. Test Methods and Remarks CAL45 Type : Applied force :50N Duration : 10 sec. Speed : Shall attain to specified force in 2 sec. FBA : Applied force : 50±3N Duration : 30±1 sec. 18. Resistance to vibration Specified Value CAL45 Type △L/L : Within ±5% LHL□□□ Appearance : No abnormality △L/L : Within ±5% Q change : Within ±30% (LHLP : only △L/L) FBA/FBR Appearance : No abnormality Impedance change : Within ±20% Test Methods and Remarks CAL45 Type : Directions : 2 hrs each in X, Y and Z directions total : 6hrs. Frequency range : 10 to 55 to 10Hz (1min.) Amplitude : 1.5mm Mounting method : Soldering onto printed board. Recovery : At least 1hr of recovery under the standard conditio n after the test, followed by the measurement within 2hrs. LHL□□□・FBA/FBR : Directions : 2 hrs each in X, Y and Z directions total : 6hrs. Frequency range : 10 to 55 to 10Hz (1min.) Amplitude : 1.5mm Mounting method : Soldering onto printed board. 19. Resistance to shock Specified Value CAL45 Type No significant abnormality in appearance LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Drop test Impact material : concrete or vinyl tile Height : 1m Total number of drops : 10 times

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 20. Solderability Specified Value CAL45 Type At least 75％ of terminal electrode is covered by ne w solder. LHL□□□ At least 75％ of terminal e lectrode is covered by new solder. FBA/FBR At least 90％ of terminal electrode is covered by new s older. Test Methods and Remarks CAL45 Type : Solder temperature : 230±5℃ Duration : 2±0.5 sec. LHL□□□ : Solder temperature : 235±5℃ Duration : 2±0.5 sec. Immersion depth : Up to 1.5mm from bottom of case. FBA/FBR : Solder temperature : 230±5℃ Duration : 3±1 sec. Immersion depth : Up to 1.5mm from terminal root. 21. Resistance to soldering heat Specified Value CAL45 Type △L/L : Within ±5% LHL□□□ No significant abnormality in appearance Inductance change : Within ±5% Q change : Within ±30%(LHLP : only △L/L) FBA/FBR No significant abnormality in appearance Impedance change : Within ±20% Test Methods and Remarks CAL45 Type : Solder temperature : 270±5℃ Duration : 5±0.5 sec. One time Immersed conditions : Inserted into substrate with t=1.6mm Recovery : At least 1hr of recovery under the standard conditi on after the test, followed by the measurement within 2hrs. LHL□□□ : Solder bath method : Solde r temperature : 260±5℃ Duration : 10±1 sec. : Up to 1.5mm from the bottom of case. Manual soldering : Solder temperature : 350±10℃ (At the tip of soldering iron) Duration : 5±1 sec. : Up to 1.5mm from the bottom of case. Caution : No excessive pressing shall be applied to terminals . Recovery : 4 to 24hrs of recovery under the standard conditio n after the test. FBA/FBR : Solder bath method: Condition 1: Solder temperature : 260±5℃ Duration : 10±1 sec. Immersion depth : Up to 1.5mm from the terminal root. Condition 2 : Solder temperature : 350±5℃ Duration : 3±1 sec. Immersion depth : Up to 1.5mm from the terminal root. Recovery : 3hrs of recovery under the standard condition afte r the test. 22. Resistance to solvent Specified Value CAL45 Type Please avoid the ultrasonic cleaning of this produc t. LHL□□□ FBA/FBR No significant abnormality in appearance Impedance change : Within ±20% Test Methods and Remarks FBA/FBR : Solvent temperature : 20～25℃ Duration : 30±5 sec. Solvent type : Acetone Recovery : 3hrs of recovery under the standard condition after the test.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 23. Thermal shock Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP：only △L/L) FBA/FBR Appearance : No abnormality Impedance change : Within ±20% Test Methods and Remarks CAL45 Type：Conditions for 1cycle Step Temperature (℃) Duration (min.) 1 －25＋0/－3 30±3

2 Room temperature Within 3

3 ＋85＋2/－0 30±3

4 Room temperature Within 3

Number of cycles : 5 cycles Recovery : At least 1hr of recovery under the standard conditi o n a f t e r t h e r e m o v a l f r o m t e s t c h a m b e r , f o l l o w e d b y t h e measurement within 2hrs. LHL□□□・FBA/FBR： According to JIS C0025 Conditions for 1 cycle Step Temperature (℃) Duration (min.)

1 Minimum operating temperature＋0/－3 30±3

3 Minimum operating temperature＋2/－0 30±3

Number of cycles : 10 cycles 〔LHL□□□〕 Recovery : 5 cycles (FBA/ FBR) : 4 to 24hrs of recovery under the standard condition after th e removal from the test chamber. 〔LHL□□□〕 : 3hrs of recovery under the standard condition after the remo val from the test chamber. (FBA/ FBR) 24. Damp heat Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ FBA/FBR Appearance：No abnormality Impedance change：Within ±20% Test Methods and Remarks CAL45 Type : Temperature : 40±2℃ Humidity : 90～95%RH Duration : 1000 hrs Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. FBA/FBR : Temperature : 60±2℃ Humidity : 90～95%RH Duration : 1000 hrs Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 25. Loading under damp heat Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L) FBA/FBR Test Methods and Remarks CAL45 Type : Temperature : 40±2℃ Humidity : 90～95%RH Duration : 1000 hrs Applied current : Rated current Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. LHL□□□ : Temperature : 40±2℃ Humidity : 90～95%RH Duration : 1000＋48/-0 hrs Applied current : Rated current Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 26. Loading at high temperature Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Temperature : 85±2℃ Duration : 1000 hrs Applied current : Rated current Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. 27. Low temperature life test Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L) FBA/FBR Test Methods and Remarks CAL45 Type : Temperature : －25±2℃ Duration : 1000 hrs Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. LHL□□□ : Temperature :－40±3℃ Duration : 1000＋48/-0 hrs Recovery : 1 to 2hrs of recovery under the standard condition a fter the removal from the test chamber. 28. High temperature life test Specified Value CAL45 Type LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L) FBA/FBR Test Methods and Remarks LHL□□□ : Temperature : 105±2℃ Duration : 1000＋48/-0 hrs Recovery : 1 to 2hrs of recovery under the standard condition a fter the removal from the test chamber.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_prec_e-E02R01 AXIAL LEADED INDUCTORS（CAL Type）、 RADIAL LEADED INDUCTORS（LH Type）、 LEADED FERRITE BEAD INDUCTORS（FB Series A Type／R Type） ■PRECAUTIONS 1. Circuit Design Precautions ◆Operating environment 1. The products described in this specification are intended fo r use in general electronic equi pment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliabi lity (traffic systems, safety equipment, aerospace systems, nuc lear control systems and medical equipment including life-support sy stems,) where product failure might result in loss of life, inj ury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions ◆Design 1. Please design insertion pitches as matching to that of leads of the component on PCBs. Technical considerations ◆Design 1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. 3. Considerations for automatic placement Precautions ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical considerations ◆Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4. Soldering Precautions ◆Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. 2. Do not immerse the entire inductor in the flux during the soldering operation. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. ◆Recommended conditions for using a soldering iron: ・Put the soldering iron on the land-pattern. ・Soldering iron's temperature - Below 350℃ ・Duration - 3 seconds or less ・The soldering iron should not directly touch the inductor. ◆Reflow soldering 1. As for reflow soldering, please contact our sales staff. Technical considerations ◆Lead free soldering 1. If products are used beyond the range of the recommended con ditions, heat stresses may deform the products, and consequentl y degrade the reliability of the products. ◆Recommended conditions for using a soldering iron If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. 5. Cleaning Precautions ◆Cleaning conditions 1. CAL type, LH type Please do not do cleaning by a supersonic wave. Technical considerations ◆Cleaning conditions 1. CAL type, LH type, If washing by supersonic waves, supersonic waves may deform products.

▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_prec_e-E02R01 6. Handling Precautions ◆Handling 1. Keep the inductors away from all magnets and magnetic objects. ◆Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. 2. LH type If inductors are dropped onto the floor or a hard surface they should not be used. ◆Packing 1. Please do not give the inductors any excessive mechanical shocks. In loading, please pay attention to handling indication mention ed in a packing box (a loading direction / number of maximum lo ading / fragile item). Technical considerations ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. LH type There is a case to be broken by a fall. ◆Packing 1. There is a case that a lead wire could be deformed by a fall or an excessive shock. 7. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions ・Ambient temperature 0～40℃ ・Humidity Below 70% RH The ambient temperature must be kept below 30℃. Even under idea l storage conditions, solderab ility of products electrodes may decrease as time passes. For this reason, inductors should be used within one year from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place.