FAP-42-P/Q

FAP MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

MODEL: FAP FAP SPECIFICATIONS ES-1451 Rev.11 Page 1/4 http://www.m-system.co.jp/ Space-saving Plug-in Signal Conditioners F-UNIT DC/FREQUENCY CONVERTER Functions & Features

• Providing a pulse rate output in proportion to DC input signal
• High-density mounting Typical Applications
• Totalizing applications in combination with a counter 26 (1.02) 100 (3.94) mm (inch) 137 (5.39) MODEL: FAP–[1][2]–[3][4]

ORDERING INFORMATION

• Code number: FAP-[1][2]-[3][4] Specify a code from below for each of [1] through [4]. (e.g. FAP-61-K/Q)
• Special input range (For codes Z & 0)
• Output frequency range (e.g. 0 – 500 Hz)
• Specify the specification for option code /Q (e.g. /C01/S01) [1] INPUT Current A: 4 – 20 mA DC (Input resistance 250 Ω) D: 0 – 20 mA DC (Input resistance 50 Ω) G: 0 – 1 mA DC (Input resistance 1000 Ω) H: 10 – 50 mA DC (Input resistance 100 Ω) Z: Specify current (See INPUT SPECIFICATIONS) ( 0 % input must be 0 mA.) Voltage 3: 0 – 1 V DC (Input resistance 1 MΩ min.) 4: 0 – 10 V DC (Input resistance 1 MΩ min.) 5: 0 – 5 V DC (Input resistance 1 MΩ min.) 6: 1 – 5 V DC (Input resistance 1 MΩ min.) 0: Specify voltage (See INPUT SPECIFICATIONS) ( 0 % input must be 0 V.) [2] OUTPUT 1: Open collector (max. 1 kHz) 2: 5 V pulse (max. 1 kHz) 5: Photo MOSFET relay pulse (max. 30 Hz) [3] POWER INPUT AC Power K: 85 – 132 V AC (Operational voltage range 85 – 132 V, 47 – 66 Hz) L: 170 – 264 V AC (Operational voltage range 170 – 264 V, 47 – 66 Hz) DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) P: 110 V DC (Operational voltage range 85 – 150 V, ripple 10 %p-p max.) [4] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q (multiple selections) COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating TERMINAL SCREW MATERIAL /S01: Stainless steel GENERAL SPECIFICATIONS Construction: Plug-in Connection: M3.5 screw terminals (torque 0.8 N·m) Screw terminal: Nickel-plated steel (standard) or stainless steel Housing material: Flame-resistant resin (black) Isolation: Input to output to power Zero adjustment: 0 – 5 % (front) Span adjustment: 95 to 105 % (front) INPUT SPECIFICATIONS ■ DC Current: Shunt resistor attached to the input terminals (0.5 W) Specify input resistance value for code Z. ■ DC Voltage: 0 – 300V DC Minimum span: 1V Input resistance: 1 MΩ min.

MODEL: FAP FAP SPECIFICATIONS ES-1451 Rev.11 Page 2/4 http://www.m-system.co.jp/ OUTPUT SPECIFICATIONS ■ Open Collector: 30 V DC @100 mA (resistive load) Frequency range: 0 – 10 pulses/hour through 1 kHz Saturation voltage: 0.6 V DC ■ 5 V Pulse Frequency range: 0 – 10 pulses/hour through 1 kHz Hi level: 3.0 – 5.5 V Lo level: ≤ 0.5 V Load resistance: 250 Ω min. ■ Photo MOSFET Relay Pulse Frequency range: 0 – 10 pulses/hour through 30 Hz Timer: Limits ON time within 75 ±25 msec. Rating: 132 V AC @ 200 mA (cos ø = 1)

30 V DC @ 200 mA (resistive load)

ON resistance: ≤ 2 Ω OUTPUT PULSE WIDTH

• Open Collector • Voltage Pulse OFF ON 20 % 80 % 1 / f ■ Frequency less than 500 Hz at 100% input ➞ Duty ratio 20% (See the figure below)
• Photo MOSFET Relay Pulse OFF ON 20 % 80 % 1 / f H Level L Level 20 % 80 % 1 / f
• Open Collector • Voltage Pulse ■ Frequency greater than 500 Hz at 100% input ➞ See the figure and equation below. H Level L Level Pulse Width OFF ON Pulse Width Pulse Width [millisec.] = 1 2.09 × 100% Frequency [kHz] ■ Photo MOSFET Relay Pulse ➞ See the figure below. ON pulse width is limited within 75 ±25 msec. when the output frequency gets low (below 2 to 4 Hz). INSTALLATION Power consumption
• AC: Approx. 4.5 VA
• DC: 24 V approx. 70 mA 110 V approx. 20 mA Operating temperature: -5 to +55°C (23 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Surface or DIN rail; Standard Rack Mounting Frame BX-16H available Weight: 190 g (0.42 lb) PERFORMANCE in percentage of span Accuracy: ±0.1 % Temp. coefficient: ±0.015 %/°C (±0.008 %/°F) Response time: Approx. 3 sec. (0 – 90 %) Line voltage effect: ±0.1 % over voltage range Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength Power input code R:

1000 V AC @ 1 minute (input to output)

2000 V AC @ 1 minute (input or output or power to ground)

500 V AC @ 1 minute (I/O to power)

Power input code K, L, P:

1500 V AC @ 1 minute (I/O to power)

MODEL: FAP FAP SPECIFICATIONS ES-1451 Rev.11 Page 3/4 http://www.m-system.co.jp/ EXTERNAL DIMENSIONS unit: mm (inch) 1 2 3 4 26 (1.02) 93 (3.66) (.59) 2–4.5 (.18) HOLE 15 (.59) deep 8–M3.5 SCREW 7.8 (.31) 107 (4.21) DIN RAIL 35mm wide [3.3 (.13)] CLAMP (top & bottom) 137 (5.39)

• When mounting, no extra space is needed between units. 26 (1.02) 100 (3.94) TERMINAL ASSIGNMENTS unit: mm (inch) 3 4 1 2 INPUT RESISTOR (model: REM) 19 (.75) Input shunt resistor attached for current input.

MODEL: FAP FAP SPECIFICATIONS ES-1451 Rev.11 Page 4/4 http://www.m-system.co.jp/ SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM *Input shunt resistor attached for current input. Isolation Base Socket INPUT R DividerLow Drift Amplifier Output Driver + U(+) V(–) POWER OUTPUT Volt. / Freq. Converter Z S LOAD Relay or Counter Coil Spark Quenching Diode LOAD Relay or Counter Coil Varistor or Spark Quenching Circuit U ■ Open Collector Output Connection Examples ■ Voltage Pulse ■ Photo MOSFET Relay Pulse

• AC Powered
• DC Powered Specifications are subject to change without notice.