FAN6390MPX ONSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 25
Technical content
Features
- USB Type−C Rev 1.3 Compatible
- Support 60 W Output Profile
- (PDO: 5 V , 9 V , 15 V , 20 V . APDO: 9 V , 15 V , 20 V)
- Constant V oltage (CV) and Constant Current (CC) Regulation with Two Operational Amplifiers of Open−Drain Type for Dual−Loop CV/CC Control
- Charge Pump Circuit to Enhance SR Driving V oltage for High Efficiency
- Small Current Sensing Resistor (5 m/C0087) for High Efficiency
- N−Channel Back to Back MOSFET Control as a Load Switch
- Built−in Output Capacitor Bleeding Function for Fast Discharging
- Precise V oltage & Current Control for Minimum Step Size via 10−bit DAC’s
- 10−bit ADC for Monitoring V oltage, Current and Temperature
- Auto Re−start Protection Mode Option to Disable Load Switch for 2 seconds
- Support Protections; Output Over−V oltage Protection, Under−V oltage Protection, External Over Temperature Protection via NTC, Internal Over Temperature Protection, Cable Fault Protection, and CC Lines Over V oltage Protection Typical Applications
- Battery Chargers for Smart Phones, Feature Phones, and Tablet PCs
- AC−DC Adapters for Portable Devices that Require CV/CC Control www.onsemi.com MARKING DIAGRAM See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet.
ORDERING INFORMATION
MLP , QUAD CASE 510BE PIN CONNECTIONS 6390FFFB = Specific Device Code A = Assembly Location L = Wafer Lot Y = Year W = Work Week /C0071 = Pb−Free Package 6390 FFFB ALYW/C0071 /C0071 (Note: Microdot may be in either location) NC LPC GND LGATE CC1 CC2 CSP GND NC BLD NC NC CSN NTC SFB IREF VREF NC GND CP GATE VDD NC VIN (Bottom View) GND
Figure 3. Pin Connections (Bottom View) Table 1. PIN FUNCTION DESCRIPTION(MLP44)
1 NC No connection
3 GND Ground
its output voltage and supply internal bias.
8 NC No connection
9 VDD Internal supply voltage. This pin is connected to an external capacitor. 10 GATE Gate drive output. Totem−pole output to drive the external SR MOSFET.
11 CP SR gate charge pump
12 GND Ground
13 NC No connection
14 NC No connection
15 BLD Bleeder pin. This pin is tied to VBUS after the load switch to discharge VBUS.
16 NC No connection
17 GND Ground
resistor with a short PCB trace. sense resistor with a short PCB trace.
20 NTC This pin is used for external temperature detection and protection
plifier non−inverting input terminal. It is tied to the output voltage resistor divider.
24 NC No connection
Table 2. MAXIMUM RATINGS (Notes 1, 2) should not be assumed, damage may occur and reliability may be affected.
- All voltage values, except differential voltages, are given with respect to the GND pin.
- Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device.
- Meets JEDEC standards JS −001−2012 and JESD 22−C101.
Table 3. THERMAL CHARACTERISTICS (Note 4)
- T A = 25°C unless otherwise specified.
Table 4. RECOMMENDED OPERATING RANGES the Recommended Operating Ranges limits may affect device reliability.
Table 5. ELECTRICAL CHARACTERISTICS VIN = 5 V, LPC = 1.25 V, LPC width = 2 /C0109s at TJ = −40~125°C, FLPC = 100 kHz, unless otherwise specified. performance may not be indicated by the Electrical Characteristics if operated under different conditions.
Table 5. ELECTRICAL CHARACTERISTICS (continued) VIN = 5 V, LPC = 1.25 V, LPC width = 2 /C0109s at TJ = −40~125°C, FLPC = 100 kHz, unless otherwise specified. Enable Bleeder Time (Note 5) Disabling OVP & SR Gate. performance may not be indicated by the Electrical Characteristics if operated under different conditions.
VIN = 5 V, LPC = 1.25 V, LPC width = 2 /C0109s at TJ = −40~125°C, FLPC = 100 kHz, unless otherwise specified. Enable Bleeder Time (Note 5) Disabling OVP & SR Gate. Enable Bleeder Time (Note 5) Disabling OVP & SR Gate. Enable Bleeder Time Disabling OVP & SR Gate. performance may not be indicated by the Electrical Characteristics if operated under different conditions.
VIN = 5 V, LPC = 1.25 V, LPC width = 2 /C0109s at TJ = −40~125°C, FLPC = 100 kHz, unless otherwise specified. performance may not be indicated by the Electrical Characteristics if operated under different conditions.
VIN = 5 V, LPC = 1.25 V, LPC width = 2 /C0109s at TJ = −40~125°C, FLPC = 100 kHz, unless otherwise specified. performance may not be indicated by the Electrical Characteristics if operated under different conditions.
VIN = 5 V, LPC = 1.25 V, LPC width = 2 /C0109s at TJ = −40~125°C, FLPC = 100 kHz, unless otherwise specified. performance may not be indicated by the Electrical Characteristics if operated under different conditions.
FAN6390MPX state machine based offers several kinds of trim option to enhance design flexibility as Table 6 shows. Table 6. SUMMARY TABLE OF ALL KINDS OF TRIM FUNCTION “0” is for compliance box test. compensation on DFP is no need. “10” is used for PD compliance box test.
- Function explanation refers to FAN6390MPX application note.
- Based on compliance spec PPS case is current limit. Output voltage could be lower than the requested PPS voltage command during current
limit. In order to operate at current limit region, FAN6390MPX series disable UVP and operates until VIN−OFF.
- Except of PDO, all APDO power profiles are 100% CC.
Table 7. UP TO 8 KINDS OF OUTPUT POWER PROFILES SELECTED BY TRIM
15 W /C0051 P /C0051 27 W 27 W < P /C0051 45 W 45 W < P /C0051 60 W
- 9 V
- 12 V (Note 9) If PD3.0 trim activated
- PPS 5 V
- PPS 9 V
- 5 V
- 9 V
- 12 V
- 15 V If PD3.0 trim activated
- PPS 5 V
- PPS 9 V
- PPS 15 V
- 5 V
- 9 V
- 15 V
- 20 V If PD3.0 trim activated
- PPS 9 V
- PPS 15 V
- PPS 20 V 001 • 5 V
- 5.5 V
- 6.0 V
- 7.0 V
- 8.0 V
- 9 V
- 10.0 V
- 5 V
- 5.5 V
- 6.0 V
- 7.0 V
- 8.0 V
- 9 V
- 15 V
- 5 V
- 5.5 V
- 6.0 V
- 7.0 V
- 9 V
- 15 V
- 20 V 010 • 5 V
- 6.0 V
- 7.0 V
- 8.0 V
- 9 V If PD3.0 trim activated
- PPS 5 V
- PPS 9 V
- 5 V
- 6.0 V
- 7.0 V
- 9 V
- 15 V If PD3.0 trim activated
- PPS 9 V
- PPS 15 V
- 5 V
- 6.0 V
- 9 V
- 15 V
- 20 V If PD3.0 trim activated
- PPS 15 V
- PPS 20 V 011 • 5 V
- 5.5 V
- 6.0 V
- 6.5 V
- 7.0 V
- 8.0 V
- 9 V
- 5 V
- 5.5 V
- 6.0 V
- 6.5 V
- 7.0 V
- 9 V
- 15 V
- 5 V
- 5.5 V
- 6.0 V
- 6.5 V
- 9 V
- 15 V
- 20 V 100 • 5 V
- 5.6 V
- 9 V
- 11 V
- 5 V
- 5.6 V
- 9 V
- 11 V
- 15 V
- 5 V
- 5.6 V
- 9 V
- 11 V
- 15 V
- 20 V 101 • 5 V
- 9 V
- 14.5 V
- 5 V
- 9 V
- 14.5 V
- 15 V
- 5 V
- 9 V
- 14.5 V
- 15 V
- 20 V 110 • 5 V
- 9 V
- 11 V
- 5 V
- 9 V
- 11 V
- 15 V
- 5 V
- 9 V
- 11 V
- 15 V
- 20 V 111 • 5 V
- 9 V
- 15 V
- 20 V 9. 12 V can be possible to enable or disable by trim.
Figure 26. Source Only Device Connecting to Sink Device through Type C Cable for 3 A current at the vSafe5V output voltage level. Table 8. CC VOLTAGES ON SOURCE SIDE –
3.0 A @ 5 V
Figure 27. Attach to Sink Device via USB Type−C Engine and Device Policy Manager as shown in Figure 28.
Figure 28. USB PD Communications Stack communication errors as they arise. handled by the Policy Engine. determine the full capabilities of the cabling. Table 9. FAN6390MPX DEFAULT POWER PROFILE
3 A CC
ÉÉ ÉÉ WQFN24, 4x4, 0.5P CASE 510BE ISSUE O DATE 02 OCT 2013 2.82 24X 0.32 24X 0.57 4.30 0.50 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SOLDERING FOOTPRINT* *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ /C0071”, may or may not be present. GENERIC MARKING DIAGRAM* PITCH PKG OUTLINE XXXXXX= Specific Device Code A = Assembly Location L = Wafer Lot Y = Year W = Work Week /C0071 = Pb−Free Package XXXXXX XXXXXX ALYW/C0071 /C0071 DIM MIN MAX MILLIMETERS D 4.00 BSC E 4.00 BSC A 0.70 0.80 b 0.20 0.30 e 0.50 BSC L1 0.00 0.15 A3 0.20 REF A1 0.00 0.05 L 0.35 0.45 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM THE TERMINAL TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. D2 2.60 2.80 E2 2.60 2.80 e SCALE 2:1 DETAIL A L ÉÉÇÇ ÇÇ L ÇÇÉÉ ÉÉ DETAIL B MOLD CMPDEXPOSED Cu ALTERNATE A B E D 2X 0.10 C PIN ONE REFERENCE TOP VIEW2X 0.10 C A (A3) 0.08 C 0.10 C C SEATING PLANESIDE VIEW DETAIL B BOTTOM VIEW b24X 0.10 B 0.05 AC C NOTE 3 DETAIL A (Note: Microdot may be in either location) L24X 4.30 2.82 CONSTRUCTIONS ALTERNATE CONSTRUCTIONSNOTE 4 e/2 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. 98AON78470FDOCUMENT NUMBER: DESCRIPTION: Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1WQFN24, 4X4, 0.5P © Semiconductor Components Industries, LLC, 2019 www.onsemi.com
www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries i n the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property . A listing of ON Semiconductor’s product/patent ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, reg ulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the right s of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative