FAN5307SX

FAN5307 FAIRCHILD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 13

Technical content

Features

95% Efficiency, Synchronous Operation Adjustable Output Voltage Option from 0.7V to V IN 2.5V to 5.5V Input Voltage Range Customized Fixed Output Voltage Options Up to 300mA Output Current Fixed Frequency 1MHz PWM Operation High Efficiency Power Save Mode 100% Duty Cycle Low Dropout Operation Soft Start Dynamic Output Voltage Positioning µ A Quiescent Current Excellent Load Transient Response 5-Lead SOT -23 Package 6-Lead MLP 3x3mm Package

Applications

Pocket PCs, PDAs Cell Phones Battery-Powered Portable Devices Digital Cameras Low Power DSP Supplies General Description The FAN5307, a high efficiency low noise synchronous PWM current mode and Pulse Skip (Power Save) mode DC-DC converter is designed for battery-powered appli- cations. It provides up to 300mA of output current over a wide input range from 2.5V to 5.5V. The output voltage can be either internally fixed or externally adjustable over a wide range of 0.7V to 5.5V V IN by an external voltage divider. Custom output voltages are also available. Con- tact a Fairchild sales representative for customized out- put voltage options. At moderate and light loads pulse skipping modulation is used. Dynamic voltage positioning is applied, and the output voltage is shifted 0.8% above nominal value for increased headroom during load transients. At higher loads the system automatically switches to current mode PWM control, operating at 1 MHz. A current mode con- trol loop with fast transient response ensures excellent line and load regulation. In Power Save mode, the quies- cent current is reduced to 15 µ A in order to achieve high efficiency and to ensure long battery life. In shut-down mode, the supply current drops below 1 µ A. The device is available in 5-lead SOT -23 and 6-lead MLP 3x3mm packages. Typical Application EFFICIENCY vs. LOAD CURRENT VOUT = 1.8V Load Current [mA] 0.01 0.1 1 10 100 1000 Efficiency [%] 100 VIN=2.5V VIN=3.6V VIN=5.5V

www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 Pin Assignment Pin Description 5-Lead SOT-23 6-Lead 3x3mm MLP Pin No. Pin Name Pin Description IN Supply voltage input.

2 GND

Ground. 3E N Enable Input. Logic high enables the chip and logic low disables the chip and reduces supply current to <1 µ A. Do not float this pin. 4 FB Feedback Input. In case of fixed voltage options, connect this pin directly to the output. For an adjustable voltage option, connect this pin to the resistor divider. X Inductor pin. This pin is connected to the internal MOSFET switches. Pin No. Pin Name Pin Description 1E N Enable Input. Logic high enables the chip and logic low disables the chip and reduces supply current to <1 µ A. Do not float this pin. Reference ground. IN Supply voltage input. 4 L X Inductor pin. This pin is connected to the internal MOSFET switches.

5 PGND

Power ground. Internal N-channel MOSFET is connected to this pin. 6F B Feedback Input. In case of fixed voltage options, connect this pin directly to the output. For an adjustable voltage option, connect this pin to the resistor divider.

www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 Absolute Maximum Ratings Recommended Operating Conditions Notes: 1. Junction to ambient thermal resistance, θ JA , is a strong function of PCB material, board thickness, thickness and number of copper planes, number of vias used, diameter of via used, available copper surface, and attached heat sink characteristics. 2. Using Mil Std. 883E, method 3015.7(Human Body Model) and EIA/JESD22C101-A (Charge Device Model). 3. Refer to the applications section for further details. Parameter Min Max Unit V IN -0.3 6.5 V Voltage on any other pin GND-0.3 V IN + 0.3 V Thermal Resistance (Note 1) Junction to case, SOT -23 130 °C/W Junction to tab, MLP 3x3 8 Lead Soldering Temperature (10 seconds) 260 °C Storage Temperature -65 150 °C Electrostatic Discharge (ESD) Protection Level (Note 2) HBM 4 kV CDM 1 Parameter Min Typ Max Unit Supply Voltage Range 2.5 5.5 V Output Voltage Range, Adjustable Version 0.7 V IN V Output Current 300 mA Inductor (Note 3) 10 µ H Input Capacitor (Note 3) 4.7 µ F Output Capacitor (Note 3) 10 µ F Operating Ambient Temperature Range -40 +85 °C Operating Junction Temperature Range -40 +125 °C

www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 General Electrical Characteristics Electrical Characteristics for Adjustable Version V IN = 2.5V to 5.5V, I OUT = 200mA, EN = V IN , C IN = 4.7µF , C OUT = 22µF , L X = 10µH, T A = -40°C to +85°C, unless otherwise noted. Typical values are at T A = 25°C. Parameter Conditions Min. Typ. Max. Units Input Voltage 2.5 5.5 V Quiescent Current I OUT = 0mA, Device is not switching 15 30 µ A Shutdown Supply Current EN = GND 0.1 1 µ A Enable High Input Voltage 1.3 V Enable Low Input Voltage 0.4 V En Input Bias Current EN = V IN or GND 0.01 0.1 µ A PMOS On Resistance V IN = V GS = 3.6V 530 690 m Ω V IN = V GS = 2.5V 670 850 NMOS On Resistance V IN = V GS = 3.6V 430 540 m Ω V IN = V GS = 2.5V 530 660 P-channel Current Limit 2.5V < V IN < 5.5V 400 520 700 mA N-channel Leakage Current V DS = 5.5V 0.1 1 µ A P-channel Leakage Current V DS = 5.5V 0.1 1 µ A Switching Frequency 800 1000 1200 kHz Line Regulation V IN = 2.5 to 5.5V, I OUT = 10mA 0.16 % / V Load Regulation (6-Lead 3x3mm MLP) 100mA I OUT 300mA 0.0014 % / mA Load Regulation (5-Lead SOT-23) 100mA I OUT 300mA 0.0022 % / mA Output Voltage Accuracy (5-Lead SOT-23) V IN = 2.5 to 4.5V, 0mA I OUT 300mA -4 4 % V IN = 2.5 to 5.5V, 0mA I OUT 300mA -5 4 % Leakage Current into SW Pin V IN > V OUT V SW V IN 0.1 1 µ A Reverse Leakage Current into pin SW V IN = Open, EN = GND, V SW = 5.5V 0.1 1 µ A Output Voltage Accuracy (6-Lead 3x3mm MLP) V IN = 2.5 to 5.5V, 0mA IOUT ≤ 300mA -4 4 % VIN = 2.5V to 5.5V, IOUT = 200mA, EN = VIN, CIN = 4.7µF , COUT = 22µF , LX = 10µH, TA = 25°C. Parameter Conditions Min. Typ. Max. Units Feedback (FB) Voltage 0.5 V

5 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 Electrical Characteristics for Fixed VOUT = 1.8V Version Note: 4. Transition voltage is defined as the difference between the output voltage measured at 0.1mA (PFM mode) and 300mA (PWM mode), respectively. 6. These limits also apply to any mode transition caused by any kind of load transition within specified output current range. VIN = 2.5V to 5.5V, IOUT = 200mA, EN = VIN, CIN = 4.7µF , COUT = 22µF , LX = 10µH, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = 25°C. Parameter Conditions Min. Typ. Max. Units PFM to PWM Transition Voltage (Note 4) VIN = 3.7V, TA = 25°C, 0.1mA ≤ IOUT ≤ 300mA 72 mV PFM to PWM Transition Voltage (Note 4) VIN = 4.2V, TA = 25°C, 0.1mA ≤ IOUT ≤ 300mA 72 mV Output Voltage during Mode Transition (Note 5, 6) 1.7 1.93 V Over Voltage Clamp Threshold Incl. line, load, load transients, and temperature 1.878 1.93 V 0.01 0.587 0.589 Time (mSec) ILOAD (mA) ss0 4.6 200 Load Transient Response Test Waveform tr = 10µS tf = 2µS

6 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 Typical Performance Characteristics (TA = 25°C, CIN = COUT = 10µF , L = 10µH, VOUT = 1.8V, unless otherwise noted.) START-UPLINE TRANSIENT RESPONSE LOAD TRANSIENT RESPONSE EFFICIENCY vs. LOAD CURRENT VOUT = 1.8V Load Current [mA] 0.01 0.1 1 10 100 1000 Efficiency [%] 100 NO LOAD QUIESCENT CURRENT vs. INPUT VOLTAGE Input Voltage [V] No Load Quiescent Current [µA] TA=+85ºC TA=+25ºC TA=-40ºC VIN=2.5V VIN=3.6V VIN=5.5V -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 Temperature [ºC] Frequency [kHz] 880 900 920 940 960 980 1000 1020 1040 1060 FREQUENCY vs. TEMPERATURE VIN=2.5V VIN=3.6V VIN=5.5V POWER SAVE (PFM) MODE OPERATION

7 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 Block Diagram Detailed Operation Description The FAN5307 is a step-down converter operating in a current-mode PFM/PWM architecture with a typical switching frequency of 1MHz. At moderate to heavy loads, the converter operates in pulse-width-modulation (PWM) mode. At light loads the converter enters a power-save mode (PFM pulse skipping) to keep the effi- ciency high. PWM Mode In PWM mode, the device operates at a fixed frequency of 1MHz. At the beginning of each clock cycle, the P-channel transistor is turned on. The inductor current ramps up and is monitored via an internal circuit. The P-channel switch is turned off when the sensed current causes the PWM comparator to trip when the output volt- age is in regulation or when the inductor current reaches the current limit (set internally to typically 520mA). After a minimum dead time the N-channel transistor is turned on and the inductor current ramps down. As the clock cycle is completed, the N-channel switch is turned off and the next clock cycle starts. PFM (Power Save) Mode As the load current decreases and the peak inductor cur- rent no longer reaches the typical threshold of 80mA, the converter enters pulse-frequency-modulation (PFM) mode. In PFM mode the device operates with a variable frequency and constant peak current thus reducing the quiescent current to minimum. Consequently, the high efficiency is maintained at light loads. As soon as the output voltage falls below a threshold, set at 0.8% above the nominal value, the P-channel transistor is turned on and the inductor current ramps up. The P-channel switch turns off and the N-channel turns on as the peak induc- tor current is reached (typical 140mA). The N-channel transistor is turned off before the inductor current becomes negative. At this time the P-channel is switched on again starting the next pulse. The converter continues these pulses until the high threshold (typical 1.6% above nominal value) is reached. A higher output voltage in PFM mode gives additional headroom for the voltage drop during a load transient from light to full load. The voltage overshoot during this load transient is also minimized due to active regulation during turning on the FB ERROR AMPLIFIER REF FB REF IS IS CURRENT SENSE NEG. LIMIT SENSE DIGITAL SOFT START UNDER VOLTAGE LOCKOUT LOGIC CONTROL MOSFET DRIVER OSC SLOPE COMPENSATION PFM COMPARATOR COMPARATOR OVER VOLTAGE COMPARATOR NEG. LIMIT COMPARATOR IS GND LX VINEN GND 0.5V

8 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 N-channel rectifier switch. The device stays in sleep mode until the output voltage falls below the low thresh- old. The FAN5307 enters the PWM mode as soon as the output voltage can no longer be regulated in PFM with constant peak current. 100% Duty Cycle Operation As the input voltage approaches the output voltage and the duty cycle exceeds the typical 95%, the converter turns the P-channel transistor continuously on. In this mode the output voltage is equal to the input voltage minus the voltage drop across the P-channel transistor: V OUT = VIN – ILOAD × (RdsON + RL), where R dsON = P-channel switch ON resistance ILOAD = Output current R L = Inductor DC resistance Soft Start The FAN5307 has an internal soft-start circuit that limits the inrush current during start-up. This prevents possible voltage drops of the input voltage and eliminates the out- put voltage overshoot. The soft-start is implemented as a digital circuit increasing the switch current in four steps to the P-channel current limit (520mA). Typical start-up time for a 10µF output capacitor and a load current of 200mA is 500µs. Short-Circuit Protection The switch peak current is limited cycle by cycle to a typ- ical value of 520mA. In the event of a output voltage short circuit the device operates at minimum duty cycle, therefore the average input current is typically 100mA.

9 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4

Application Information

Adjustable Output Voltage Version The output voltage for the adjustable version is set by the external resistor divider, as shown below: and is calculated as: To reduce noise sensitivity, R1 + R2 should not exceed 1M Ω . Inductor Selection The inductor parameters directly related to device perfor- mances are saturation current and dc resistance. The FAN5307 operates with a typical inductor value of 10µH. The lower the dc resistance, the higher the efficiency. For saturation current, the inductor should be rated higher than the maximum load current plus half of the inductor ripple current that is calculated as follows: where: f = Switching Frequency L = Inductor Value L = Inductor Ripple Current Input Capacitor Selection For best performances, a low ESR input capacitor is required. A ceramic capacitor of at least 4.7µF , placed as close to the input pin of the device is recommended. Output Capacitor Selection The FAN5307’s switching frequency of 1MHz allows the use of a low ESR ceramic capacitor with a value of 10µF to 22µF . This provides low output voltage ripple. In power save mode the output voltage ripple is independent of the output capacitor value and the ripple is determined by the internal comparator thresholds. The typical output voltage ripple at light load is 1% of the nominal output voltage. PCB Layout Recommendations The inherently high peak currents and switching fre- quency of the power supplies require a careful PCB lay- out design. Therefore, use wide traces for the high current path and place the input capacitor, the inductor, and the output capacitor as close as possible to the inte- grated circuit terminals. For the adjustable version the resistor divider should be routed away from the inductor to avoid electromagnetic interference. The 6-lead MLP version of the FAN5307 separates the high current ground from the reference ground, therefore it is more tolerant to the PCB layout design and shows better performance. Inductor Value Vendor Part Number Perfor- mance 10µH Sumida CDRH5D28-100 High EfficiencyCDRH5D18-100 CDRH4D28-100 Murata LQH66SN100M01L 6.8µH Sumida CDRH3D16-6R8 Smallest Solution10µH CDRH4D18-100 CR32-100 CR43-100 Murata LQH4C100K04 Table 1: Recommended Inductors 100kΩ V OUT 0.5V 1 R 1 R 2 ∆ IL V OUT 1V OUT V IN⁄()– Capacitor Value Vendor Part Number 4.7µF Taiyo Yuden JMK212BY475MG 10µF JMK212BJ106MG JMK316BJ106KL TDK C12012X5ROJ106K C3216X5ROJ106M 22µF Murata GRM32DR60J226K Table 2: Recommended Capacitors

10 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 Mechanical Dimensions 6-Lead 3x3mm MLP Package B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994 NOTES: A. CONFORMS TO JEDEC REGISTRATION MO-229, VARIATION WEEA, DATED 11/2001

0.10 C A B

0.05 C TOP VIEW BOTTOM VIEW RECOMMENDED LAND PATTERN 0.15 C 0.08 C 3.0 3.0 0.05 0.00 2.25 1.65 1.90 0.15 C 0.45 0.20

0.8 MAX

0.10 C PIN #1 IDENT 1 3

460.2 MIN

2.101.65 2.45 0.65 TYP0.95 TYP 3.50 (0.70) 0.30~0.45 (0.20) 0.95

11 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4 Mechanical Dimensions 5-Lead SOT-23 Package Symbol Inches Millimeters Notes Min Max Min Max A .035 .057 .90 1.45 A1 .000 .006 .00 .15 B .008 .020 .20 .50 c .003 .010 .08 .25 D .106 .122 2.70 3.10 E .059 .071 1.50 1.80 e .037 BSC .95 BSC e1 .075 BSC 1.90 BSC H .087 .126 2.20 3.20 L .004 .024 .10 .60 α 0° 10° 0° 10° e B D E H A α L c Notes: 1. Package outline exclusive of mold flash & metal burr. 2. Package outline exclusive of solder plating. 3. EIAJ Ref Number SC_74A

12 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter FAN5307 Rev. 1.0.4

Ordering Information

Product Number V OUT (V) Package Type Order Code FAN5307 1.8 5-Lead SOT -23 Tape and Reel FAN5307S18X 1.8 6-Lead 3x3mm MLP Tape and Reel FAN5307MP18X 1.5 5-Lead SOT -23 Tape and Reel FAN5307S15X 1.5 6-Lead 3x3mm MLP Tape and Reel FAN5307MP15X Adjustable 5-Lead SOT -23 Tape and Reel FAN5307SX Adjustable 6-Lead 3x3mm MLP Tape and Reel FAN5307MPX

13 www.fairchildsemi.com FAN5307 High-Efficiency Step-Down DC-DC Converter DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY , FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. LIFE SUPPORT POLICY FAIRCHILDíS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Preliminary No Identification Needed Obsolete This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Formative or In Design First Production Full Production Not In Production ISOPLANAR™ LittleFET™ MICROCOUPLER™ MicroFET™ MicroPak™ MICROWIRE™ MSX™ MSXPro™ OCX™ OCXPro™ OPTOLOGIC OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerEdge™ FAST FASTr™ FPS™ FRFET™ GlobalOptoisolator™ GTO™ HiSeC™ I 2C™ i-Lo™ ImpliedDisconnect™ IntelliMAX™ Rev. I17 ACEx™ ActiveArray™ Bottomless™ Build it Now™ CoolFET™ CROSSVOLT™ DOME™ EcoSPARK™ E 2CMOS™ EnSigna™ FACT™ FACT Quiet Series™ PowerSaver™ PowerTrench® QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ RapidConnect™ µSerDes™ ScalarPump™ SILENT SWITCHER SMART START™ SPM™ Stealth™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TinyLogic TINYOPTO™ TruTranslation™ UHC™ UltraFET UniFET™ VCX™ Wire™ Across the board. Around the world.™ The Power Franchise Programmable Active Droop™ FAN5307 Rev. 1.0.4