F404 GAMEWELL-FCI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Features

  • Four Style B (Class B) Initiating Device Circuits (IDCs); two Style Y (Class B) Notification Appliance Circuits (NACs); optional module (P/ N CAC-4) converts 4 IDCs and two NACs to Class A. 24 VDC.
  • NAC synchronization features: – Provides synchronization of standard ANSI audible signals as required by NFPA 72 – Provides synchronization of ADA compliant strobes per NFPA 72 (4-4.4.1). – Selectable for System Sensor, Cooper- Wheelock,& Gentex protocols. – Selective Silence feature allows manual silencing of horns while strobes continue to flash on the same NAC.
  • Silent or Audible Walk Test operation mode commanded from the front keypad, with automatic return to normal after one hour of inactivity.
  • Alarm verification selectable per zone.
  • Each zone may be programmed for supervisory or fire; each zone has separate red and yellow LEDs.
  • Disable switches provided for each zone.
  • NACs programmable for: Silence Inhibit, Auto Silence, Strobe Synchronization, Selective Silence (horn/strobe mute), Temporal or Steady signal, Silenceable or Nonsilenceable.
  • Form-C Alarm, Trouble, and Supervisory relays.
  • 3.0 A (6.0 A with optional second transformer) total usable current.
  • Piezo sounder for alarm, trouble, supervisory, and maintenance.
  • Control buttons: ACK (Acknowledge), Alarm Silence, Reset, Walktest, Zone Enable/Disable (one per zone).
  • LED indicators: Fire Alarm (one per zone), Supervisory (one per zone), Trouble (one per zone), Maintenance (one per zone), AC Power, NAC Disable, Zone Disable, NAC Fault, System Trouble, Power Trouble, Walktest, Alarm Silence, Earth Fault (on circuit board), Battery Fault (on circuit board), Charger Fault (on circuit board).
  • Optional dress panel (P/N DP-FLEX).
  • Optional modules: plug-in transmitter module (P/N 4XTMF); plug-in zone relay module (P/N 4XZMF); transmitter module (P/N 4XLMF) for SAN-404 remote LED annuncia- tor. Listings Listings and approvals below apply to the basic Flex 404 panel. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status.
  • UL Listed: file S521.
  • CSFM approved: file 7165-1288:180.
  • MEA approved: file 366-04-E. Flex 404 Four-Zone Fire Alarm Control Panel g2404ph1.jpg

Flex 404 Four-Zone FACP CS-2404 09/01/06Page 2 of 2 Specifications and wiring information are provided for information only and are believed to be accurate. Gamewell-FCI assumes no responsibility for their use. Data and design are subject to change without notice. Installation and wiring instructions shipped with the product shall always be used for actual installation. For more information, contact Gamewell-FCI. Gamewell-FCI

12 Clintonville Road

Northford, CT 06472-1610 Phone: 203-484-7161 Fax: 203-484-7118 www.gamewell-fci.com A Honeywell Company © 2006 Gamewell-FCI Specifications AC power, TB8 120 VAC, 50/60 Hz, 2.3 A. Wire size: minimum 14 AWG (2.0 mm²) with 600 V insulation. Battery (sealed lead-acid only), J8 Maximum charging circuit: normal flat charge 27.6 VDC @ 0.8 A. Maximum battery charger capacity: 18 AH battery. Two 7 AH batteries can be housed in the FACP cabinet.Larger batteries require a separate battery box i.e. BB-17F. Initiating device circuits, TB3 Alarm zones 1 – 4. Power-limited circuitry. Operation: all zones Style B (Class B). Normal operating voltage: nominal 22 VDC. Alarm current: 15 mA minimum. Standby current: 4 mA. Short circuit current: 40 mA maximum. Maximum loop resistance: 100 ohms. End- of-line resistor: 4.7K ohm, 1/2 watt (P/N 71252). Notification appliance circuits, TB2 Two NACs on Flex 404. Power-limited circuitry. Normal operating voltage: nominal 24 VDC. Maximum signaling current: 2.5 A total with standard transformer; 5.0 A total (2.5 maximum per NAC) with optional trans- former. End-of-line resistor: 4.7K ohm, 1/2 watt (P/N 71252). Form-C relays Trouble relay TB5 (fail-safe). Alarm relayTB6. Contact ratings: 2.0 A @ 30 VAC (resistive). Auxiliary outputs Resettable power, TB1 Power-limiting circuitry. Operating voltage: nominal 24 VDC. Maximum available current: 500 mA, appropriate for powering four-wire smoke detectors. See note under nonresettable. Nonresettable power, TB1 Power-limiting circuitry. Operating voltage: nominal 24 VDC. Maximum available current: 500 mA, appropriate for powering four-wire smoke detectors. Note: Total current for nonre-settable power, resettable power and two NACs must not exceed 6 A for the Flex 404. Cabinet dimensions Door: 15.342" (38.97 cm) high x 14.677" (37.28 cm) wide x 0.375" (0.95 cm) deep. Backbox: 15.0" (38.10 cm) high x 14.5" (36.83 cm) wide x 3.0" (7.62 cm) deep. Backbox Mounting The cabinet can be surface-mounted. The door is removable during installation by opening and lifting it off the hinges. The cabinet mounts using two key slots at the top of the backbox and two additional 0.250" diameter holes at the bottom.

Ordering Information

F404 Four-zone conventional FACP . XRM-24 120 VAC, 100 VA transformer, expands NAC power from 3.0 to 5.0 Amps. CAC-4 Class A converter module. Used to convert Style B (Class B) IDC to Style D (Class A) and Style Y (Class B) NAC to Style Z (Class A). The module connects to J1 on the Flex 404 circuit board. 4XTMF Transmitter module. 4XLMF LED interface module, supports SAN-404. 4XZMF Zone relay module. 411UD Four-input (channel) 411UD dual-line Digital Alarm Commu- nicator/Transmitters, which can be used as slave communi- cators with Flex 404. PRO-411 Programmer used with 411UD. SAN-404 Remote annunciator (RZA-4XF), mounts in a single-gang box. BB-17F Battery box, required to house two batteries greater than 7 AH, to a maximum of 18 AH. DP-FLEX Dress panel. TR-1-R Trim ring for semi-flush mounting. 52194 Flex 404 Installation and Maintenance Manual. i³™ is a trademark and Gamewell® is a registered trademark of Honeywell International Inc.