F38 NICHICON | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 1
Technical content
CONDUCTIVE POLYMER TANTALUM SOLID ELECTROLYTIC CAPACITORS Specifications Drawing Marking Standard rating Item Performance Characteristics Category Temperature Range Capacitance Tolerance Dissipation Factor (at 120Hz) ESR (100kHz) Leakage Current Ripple Current Damp Heat (No voltage applied) Temperature Cycles Resistance to Soldering Heat Surge Endurance 1 Endurance 2 Shear Test Terminal Strength –55 to +105˚C (Rated temperature + 85˚C) ±20% (120Hz) Refer to the list below Refer to the list below After 5 minute's application of rated voltage, leakage current at 20˚C is not more than 0.1CV Type numbering system (Example : 6.3V 10µF) F38 J0 1 0 6 M M A 123 546 78 91 0 1 1 Rated Capacitance Capacitance tolerance Case code Rated voltage Series Tape width (mm) Reel Dia (φ180mm) 8 A Taping code At 60˚C, 90 to 95% R.H. 500hours –55˚C / +105˚C 30 minutes each 5 cycle Test Condition ; 10 second reflow at 240˚C Capacitance Change Within –20 to +30% of initial value Capacitance Change Within ±20% of initial value Capacitance Change Within ±20% of initial value After application of surge voltage in series with a 1kΩ resistor at the rate of 30 seconds ON, 30 seconds OFF , for 1000 sucessive test cycles at 85˚C, capacitors meet the characteristics requirements listed below. Capacitance Change...Within ±20% of initial value After 1000 hours' application of rated voltage in series with a 3Ω resistor at 85˚C. Capacitance Change....Within ±20% of initial value Dissipation Factor...1.5 times initial specified value or less Leakage Current...Initial specified value or less After 1000 hours' application of derated voltage in series with a 3Ω resistor at 105˚C,capacitors meet the characteristic requirements listed below Capacitance Change....Within ±20% of initial value Dissipation Factor...3 times initial specified value or less Leakage Current...Initial specified value or less After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on an aluminum substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with a specified jig at the center of the substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. Refer to the list below 5N (0.51kg • f) For 10±1 seconds 20R230 45 45 1mm M Case Rated voltage (Voltage code) J S Case Rated voltage (Voltage code) Capacitance code Jn L H W 1 W 2 S1S2S1 (mm) Case code LW 1 S2W 2 HS 1 Standard ratings ( ) The series in parentheses are being developed. Please contact to your local Nichicon sales office when these series are being designed in your application. Cap.( F) Code V 4.7 475 106 226 336 476 M M S S 6.3 M M
- S S (S) M M • S (S) S a n s Capacitance codeµ Rated Volt (V) Rated Capacitance Leakage CurrentDisspation Factor (%@120Hz) ESR (mΩ @100kHz) Rated Ripple (mArms@100kHz) Case code 6.3 4.7 M M S S M M S S M M S 4.0 8.8 13.2 18.8 6.3 13.9 13.9 20.8 4.7 10.0 10.0 200 200 200 200 200 200 200 200 200 200 200 350 350 450 450 350 350 450 450 350 350 450 Part Number F380G106MMA F380G226MMA F380G336MSA F380G476MSA F380 J 106MMA F380 J 226MSA F380 J 226MMA F380 J 336MSA F381A475MMA F381A106MMA F381A106MSA Adapted to the RoHS directive (2002/95/EC). F38 Conductive Polymer Resin-molded Chip, High Capacitance Series ∗ As for the surge voltage refer to page 301 for details. CAT.8100X (µF) (µF)