F2415S-1W

F0305S-1W MORNSUN | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 2

Technical content

MORNSUN reserves the copyright Specifications subject to change without notice. E_S-1W & F_S-1W A/1-2007 Page 1 of 2 E_S-1W & F_S-1W Series 1W, FIXED INPUT, ISOLATED & UNREGULATED DUAL/SINGLE OUTPUT DC-DC CONVERTER Multi-country patent protection RoHS FEATURES PRODUCT PROGRAM Input Output Voltage (VDC) Current (mA) Part Number Nominal Range Voltage (VDC) Max Min Efficiency (%, Typ) Certificate F0305S-1W 3.3 3.0-3.6 5 200 20 74 E0505S-1W ±5 ±100 ±10 71 UL E0509S-1W ±9 ±56 ±6 77 UL E0512S-1W ±12 ±42 ±5 77 UL E0515S-1W ±15 ±33 ±4 79 UL F0503S-1W 3.3 303 30 73 F0505S-1W 5 200 20 72 UL F0509S-1W 9 111 12 76 UL F0512S-1W 12 83 9 79 UL F0515S-1W 5 4.5-5.5 15 67 7 78 UL E1205S-1W ±5 ±100 ±10 73 UL E1209S-1W ±9 ±56 ±6 77 UL E1212S-1W ±12 ±42 ±5 80 UL E1215S-1W ±15 ±33 ±4 80 UL F1205S-1W 5 200 20 70 UL F1209S-1W 9 111 12 75 UL F1212S-1W 12 83 9 78 UL F1215S-1W 12 10.8-13.2 15 67 7 79 UL F1505S-1W 15 13.5-16.5 5 200 20 69 E2405S-1W ±5 ±100 ±10 73 UL E2409S-1W ±9 ±56 ±6 77 UL E2412S-1W ±12 ±42 ±5 80 UL E2415S-1W ±15 ±33 ±4 80 UL F2405S-1W 5 200 20 71 UL F2409S-1W 9 111 12 76 UL F2412S-1W 12 83 9 78 UL F2415S-1W 24 21.6-26.4 15 67 7 80 UL Note: The E_S-W25/F_S-W25 series also are available in our company. COMMON SPECIFICATIONS Item Test conditions Min Typ Max Units Operating Temp. Range -40 85 Storage Temp. Range -55 125 Storage humidity range 95 % Cooling Free air convection Temp. rise at full load 15 25 Lead temperature 1.5mm from case for 10 seconds 300 Isolation voltage Tested for 1 minute and 1 mA max 3000 VDC Isolation resistance Test at 500VDC 1000 M Ω Short circuit protection* 1 s Case material Plastic (UL94-V0) MTBF 3500 K hours Weight 2.1 g High Efficiency up to 80% 3000VDC Isolation Internal SMD construction No Heat sink Required Temperature Range: -40°C to +85°C No External Component Required Industry Standard Pinout RoHS Compliance

APPLICATIONS

The E_S-1W & F_S-1W Series are specially designed for applications where a group of polar power supplies are is olated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation ≤ ±10%); 2) Where isolation is necessary between input and output (isolation voltage ≤3000VDC); 3) Where the regulation of the output voltage and the output ripple noise are not demanding. Such as: purely digital circuits, ordinary low frequency analog circuits, and IGBT power device driving circuits. MODEL SELECTION E0505S-1W Product Series Input Voltage Output Voltage Package Style Rated Power MORNSUN Science& Technology co.,Ltd. Address: 2th floor 6th building, Hangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax: 86-20-38601272 http://www.mornsun-power.com *supply voltage must be discontinued at the end of short circuit duration.

MORNSUN reserves the copyright Specifications subject to change without notice. E_S-1W & F_S-1W A/1-2007 Page 2 of 2 OUTPUT SPECIFICATIONS Item Test conditions Min Typ Max Units Output power 0.1 1 W (3.3 input) ±1.5 Line regulation For Vin change of ±1% (others input) ±1.2 (3.3 output) 12 20 (5V output) 10 15 (9V output) 8.3 15 (12V output) 6.8 15 Load regulation 10% to 100% load (15V output) 6.3 15 Output voltage accuracy See tolerance envelope graph Temperature drift 100% full load 0.03 %/°C (EXXXXS-1W） 50 75 (EXX24S-1W） 100 150 (FXXXXS-1W） 75 100 Ripple& Noise* 20MHz Bandwidth (FXX24S-1W） 100 150 mVp-p Switching frequency Full load, nominal input 100 KHz *Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power Converter section, application notes. Note: 1.All specifications measured at T A=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2.Dual output models unbalanced load: ±5%. TYPICAL CHARACTERISTICS Operating Temp.(C) o OUTLINE DIMENSIONS & PIN CONNECTIONS Dual Output Single Output Pin Single Dual FOOTPRINT DETAILS RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch), diameter:1.00mm Note: Unit:mm(inch) Pin section:0.50*0.30mm(0.020*0.012inch) Pin tolerances:0.10mm(0.004inch) General tolerances:0.25mm(0.010inch) First Angle Projection GND -V0 +Vo 1 2 5 6 1 2 GND No pin +Vo Side view Bottom view 5 VinVin APPLICATION NOTE Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load is not less than 10% of the full load, and that this product should neve r be operated under no load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company ’s products with a lower rated output power (E_S-W25&F_S-W25). Overload Protection Under normal operating conditions, the output circuit of these products has no protection against overload. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. Recommended circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be con nected to the input and output ends of the DC/DC converter, see (Figure 1). Vin GND +Vo 0VDCCin L L DC L Cout Cout -Vo Dual Output L Single Output Vin GND +Vo DCCin L DC Cout (Figure 1) It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequenc y to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the recommended capacitance of its filter capacitor sees (Table 1). EXTERNAL CAPACITOR TABLE (TABLE 1) Vin (VDC) Cin (uF) Single Vout (VDC) Cout (uF) Dual Vout (VDC) Cout (uF) 12 2.2 9 4.7 ±9 2.2 15 2.2 12 2.2 ±12 1 24 1 15 1 ±15 0.47 It’s not recommended to connect any external capacitor in the application field with less than 0.5 watt output. Output Voltage Regulation and Over- voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-curren t protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series (Figure 2). Vin GND +Vout DC DC -Vout REG REG REG Dual Output Single Output Vin GND 0V +Vout DC DC REG REG (Figure2) No parallel connection or plug and play.