F1180

Integrated Device Techn...

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz

Manufacturer: Integrated Device Techn...

Document: 40 Pages / 2Mb

Request Quote Download Datasheet Read online HTML view

More from Integrated Device Techn... Browse F parts

Online Datasheet

Read F1180 online.

IDTF1130NBGI IDT | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 40

Technical content

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 1 Rev 1, April 2015 IDTF1130NBGI Datasheet G ENERAL D ESCRIPTION This document describes the specifications for the F1130 Dual Path RF Receiver consisting of RF amplifier with bypass, DSA, RF Mixer & IF amplifier in each signal path. Applications include Multizmode, Multiz carrier BaseStation Receivers. F1130 supports the following frequencies: RF from 400 MHz to 1100 MHz, LO from 500 MHz to 1300 MHz, and IF from 25 MHz to 400 MHz. Refer to the Part # Matrix below describing the complete series. The F1130 RF frontzend offers 19 dB gain with 3.5 dB NF and +37 dBm OIP3 performance. The digital step attenuator provides 30 dB adjustment range in 2 dB steps via the SPI interface controller. For strong signal conditions, each RF amplifier can be bypass controlled via the SPI interface. The RF frontzend output and mixer input signals are bonded to separate pins to allow interstage imagezreject filtering. Each of the dual mixer paths provide 9 dB power gain, 10.3 dB NF and +36 dBm OIP3 performance. An external LO signal is applied to the mixer LO port. This device is packaged in a 7mm x 7mm, 48zpin Thin QFN with 50 ohm singlezended RF & LO inputs and 200 ohm differential IF output impedance for ease of integration into the receiver lineup. COMPETITIVE ADVANTAGE The onzchip 4zbit RF digital step attenuator (DSA) has very low insertion loss and low distortion. The F1130 has very low power consumption thus allowing it to be packaged in very compact 7x7 solution /checkbld GlitchFree TM Technology /checkbld Extremely accurate with low distortion /checkbld Very small solution area

FEATURES

Dual Path for Diversity / MIMO
GlitchzFree TM Technology
RF: 400 MHz to 1100 MHz
LO: 500 MHz to 1300 MHz
IF: 25 MHz to 400 MHz
Bypassable RF amplifiers for strong signal conditions
19 dB RF frontzend power gain
+37 dBm RF frontzend OIP3 (Bypass OFF)
+43 dBm RF frontzend OIP3 (Bypass ON)
3.5 dB frontzend NF AT 900 MHz
9 dB mixer power gain (HS LO)
+36 dBm mixer OIP3
50 Ω RF & LO impedance
200 Ω differential IF output impedance
Independent CHA, CHB path standby mode
30 dB gain control range, 2dB steps
3 bit SPI control
Total I CC = 360 mA
7mm x 7mm, 48zpin TQFN package FUNCTIONAL BLOCK D IAGRAM PART # M ATRIX Part# RF freq range (MHz) UTRA bands IF freq range (MHz) LO freq range (MHz) F1130 400 - 1100 5,6,8,12,13,14,1 718,19,20, 26 25 – 400 500 - 1300 F1180 1400 - 2700 1,2,3,4,7,9,10, 11,15,16,21,23, 24,25,33,34,35, 36,37,39,40,41 25 – 400 1350 - 2900

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 2 Rev 1, April 2015 IDTF1130NBGI Datasheet ABSOLUTE M AXIMUM RATINGS Parameter Symbol Min Max Units VCC to GND V CC z0.3 +5.5 V SPI DATA, SPI LE, SPI CLK, STBY_A, STBY_B V Logic z0.3 V cc + 0.25 V IFOUT_A+, IFOUT_Az, IFOUT_B+, IFOUT_Bz, I IF 1.00 V cc + 0.30 V LO_IN, RFIN_A, RFIN_B, MIXRFIN_A, MIXRFIN_B V Cntl z0.3 +0.30 V LO_BIAS VLO +2.1 +4.0 V RFA_BIAS, RFB_BIAS V RFIN z0.3 +1.50 V RFAMP_BIAS, IFA_BIAS, IFB_BIAS V Bias z0.3 +2.20 V Maximum RF Input Power – Bypass OFF 1hr < duration < 2hr @ Tcase = 105C) PRFIN_A PRFIN_B +24 dBm Maximum RF Input Power – Bypass ON 1hr < duration < 2hr @ Tcase = 105C) PRFIN_A PRFIN_B +24 dBm Maximum RF Input Power to Mixer 1hr < duration < 2hr @ Tcase = 105C) PRFMIX_A PRFMIX_B +21 dBm Continuous Power Dissipation P diss 2.15 W Junction Temperature T j +150 °C Storage Temperature Range T st z65 +150 °C Lead Temperature (soldering, 10s) +260 °C ElectroStatic Discharge – HBM (JEDEC/ESDA JSz001z2012) 2000 (Class 2) Volts ElectroStatic Discharge – CDM (JEDEC 22zC101F) 250 (Class C3) Volts Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION This product features proprietary protection circuitry. However, it may be damaged if subjected to high energy ESD. Please use proper ESD precautions when handling to avoid damage or loss of performance . PACKAGE THERMAL AND M OISTURE CHARACTERISTICS θJA (Junction – Ambient) 32 °C/W θJC (Junction – Case) [The Case is defined as the exposed paddle] 3 °C/W Moisture Sensitivity Rating (Per JzSTDz020) MSL1

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 3 Rev 1, April 2015 IDTF1130NBGI Datasheet F1130 RECOMMENDED OPERATING CONDITIONS Parameter Symbol Conditions Min Typ Max Unit s Supply Voltage(s) V CC All VCC pins 4.75 5.25 V Operating Temperature Range T CASE Case Temperature z40 +105 °C RF Freq Range F RF 400 1100 MHz LO Freq Range F LO 500 1300 MHz LO Power P LO z3 +3 dBm IF Freq Range F IF 25 400 MHz RF Amplifier Source Impedance Z RFIN_A ZRFI N_B Single Ended 50 Ω RF Amplifier Load Impedance ZRFOUT_A ZRFOUT_B Single Ended 50 Ω Mixer RF Source Impedance ZMXRRFIN_A ZMXRRFIN_B Single Ended 50 Ω Mixer LO Source Impedance ZMXRLOIN_A ZMXRLOIN_B Single Ended 50 Ω Mixer IF Load Impedance ZMXRIFOUT_A ZMXRIFOUT_B Differential 200 Ω

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 4 Rev 1, April 2015 IDTF1130NBGI Datasheet F1130 SPECIFICATION Specifications apply at V CC = +5.00 V, T CASE = +25°C, F RF = 900 MHz, F IF = 199 MHz, F LO = 1099 MHz, P LO = 0 dBm, For bypass ON, RF VGA input = +5 dBm, for Bypass OFF, RF VGA input = z20dBm/tone, Attenuator = 0 dB, STBY_A, STBY_B = GND unless otherwise noted. Trace, Connector, and external transformer losses are dezembedded. Parameter Symbol Conditions Min Typ Max Units General Logic Input High V IH All Control Pins 1.17 V Logic Input Low V IL All Control Pins 0.67 V Logic Current I IH, IIL All Control Pins -120 +120 µA Standby Mode Logic STBY STBY = VIH or Floating Power OFF STBY = VIL Power ON Supply Current ICC_ON Bypass OFF, 2 Channels 360 410 1 mA ICC_OFF1 Bypass ON, 1 Channels (CHA or CHB) 295 330 ICC_OFF2 Bypass ON, 2 Channels (CHA and CHB) 230 260 ICC_STBY Standby Mode 20 26 RF Switching time 3 τRF 10% to 90% risetime 250 ns DSA Settling time 3 τSET 10% to 90% risetime 100 ns Turn ON time 3 τON 10% to 90% risetime 225 ns Turn OFF time 3 τOFF 10% to 90% risetime 25 ns Control Interface SPI BIT 14 bit Serial Clock Speed SPI CLK 24 MHz Note 1: Items in min/max columns in bold italics are Guaranteed by Test. Note 2: Items in min/max columns that are not bold/italics are Guaranteed by Design Characterization. Note 3: Speeds are measured after SPI programming is completed (data latched with LE = HIGH). Note 4: Gain across the entire frequency band is affected by the inclusion of the RF switch.

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 5 Rev 1, April 2015 IDTF1130NBGI Datasheet F1130 SPECIFICATION (CONTINUED ) Specifications apply at V CC = +5.00 V, T CASE = +25°C, F RF = 900 MHz, F IF = 199 MHz, F LO = 1099 MHz, P LO = 0 dBm, For bypass ON, RF VGA input = +5 dBm, for Bypass OFF, RF VGA input = z20dBm/tone, Attenuator = 0 dB, STBY_A, STBY_B = GND unless otherwise noted. Trace, Connector, and external transformer losses are dezembedded. Parameter Symbol Conditions Min Typ Max Units RF VGA – Bypass OFF Gain 4 G VGA 17.5 19 20.5 dB Gain Flatness G VGA_FLAT FRF = 400 MHz to 110 MHz over any 100 MHz bandwidth ± 0.3 dB Gain Variation G VGA_T T case =z40 to +105 °C z0.4 to +0.2 dB Noise Figure NF VGA 3.5 dB Input 1 dB Power Compression IP1dB LBVGA 0 dBm Output Third Order Intercept Point OIP3 VGA Pout = 0 dBm/Tone,

1 MHz tone separation 34

RF VGA – Bypass ON Gain G BYPASS -3.5 -2.5 dB Gain Flatness G BYPASS_FLAT FRF = 400 MHz to 1100 MHz over any 100 MHz bandwidth ± 0.2 dB Gain Variation G BYPASS_T T case =z40 to +105 °C ± 0.25 dB Input 1 dB Power Compression IP1dB LBBYPASS 22 dBm Output Third Order Intercept Point OIP3 BYPASS_0 Attenuation = 0dB

1 MHz tone separation 40 43 dBm

BYPASS_6 Attenuation = 6dB

1 MHz tone separation 34 37 dBm

RF VGA – Bypass ON or OFF DSA Gain Control Range DSA RANGE 30 dB DSA Gain Step DSA STEP 2 dB Gain Accuracy DSA ACC ±(0.05 + 0.04*ATTN) Max dB Channel Isolation ISO AzB ISO BzA RFA Input to RFB Output RFB Input to RFA Output 46 52 dB VGA Input Match S11 VGA z15 dB VGA Output Match S22 VGA z15 dB Isolation between VGA RFout and Mixer RFin ISO VGA/MIX No Connection between ports 47 50 dB Note 1: Items in min/max columns in bold italics are Guaranteed by Test. Note 2: Items in min/max columns that are not bold/italics are Guaranteed by Design Characterization. Note 3: Speeds are measured after SPI programming is completed (data latched with LE = HIGH). Note 4: Gain across the entire frequency band is affected by the inclusion of the RF switch.

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 6 Rev 1, April 2015 IDTF1130NBGI Datasheet F1130 SPECIFICATION (CONTINUED ) Specifications apply at V CC = +5.00 V, T CASE = +25°C, F RF = 900 MHz, F IF = 199 MHz, F LO = 1099 MHz, P LO = 0 dBm, For bypass ON, RF VGA input = +5 dBm, for Bypass OFF, RF VGA input = z20dBm/tone, Attenuator = 0 dB, STBY_A, STBY_B = GND unless otherwise noted. Trace, Connector, and external transformer losses are dezembedded. Parameter Symbol Conditions Min Typ Max Units Mixer Gain G MXR 8 9 10 dB Gain Flatness G MXR_FLAT FRF = 1400 MHz to 2700 MHz over any 100 MHz bandwidth ± 0.2 dB IF Gain Flatness Bandwidth GIF_FLAT1 Fixed LO Flatness = 0.5 dB 200 MHz GIF_FLAT2 Fixed LO Flatness = 0.8 dB 300 MHz Gain Variation G MXR_T T case =z40 to +105 °C ± 0.8 dB Noise Figure NF MXR 10.3 dB Blocking Noise Figure NF MXR_BLK +75 MHz offset Pin (Blocker) = + 4dBm 17.5 dB Input 1 dB Compression IP1dB MXR 7 9 dBm Output Third Order Intercept Point OIP3 MXR 1 MHz tone separation 33 36 dBm Output Second Order Intercept Point OIP2 MXR 1 MHz tone separation 58 dBm 2RF – 2LO rejection 2x2 MXR F RF – FIF /2 68 dBc 3RF – 3LO rejection 3x3 MXR Frequency = F RF – 2*FIF /3 70 dBc Second Harmonic HD2 MXR 65 dBc Third Harmonic HD3 MXR 80 dBc Settling Time τMXR_SET Pin = z13 dBm STBY VIH to VIL Time for IF to settle to 0.1 dB of final value 170 ns Mixer RF Input Match S11 MXR_RF z15 dB Mixer LO Input Match S11 MXR_LO z15 dB Mixer IF Output Match S22 MXR_IF z13 dB Channel Isolation ISO IF IFOUT_A to IFOUT_B 70 dBc RF to IF Isolation ISO RI Pin = z10 dBm Ratio of IF level to RF leakage at IF port 36 dBc LO to RF Leakage ISO LR z47 dBm LO to IF Leakage ISO LI z37 dBm Note 1: Items in min/max columns in bold italics are Guaranteed by Test. Note 2: Items in min/max columns that are not bold/italics are Guaranteed by Design Characterization. Note 3: Speeds are measured after SPI programming is completed (data latched with LE = HIGH). Note 4: Gain across the entire frequency band is affected by the inclusion of the RF switch.

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 7 Rev 1, April 2015 IDTF1130NBGI Datasheet Serial Control Mode Data is clocked in LSB first via serial mode. Serial data is formatted as a 14zbit word. The 14zbit word contains logic for bypass mode, 4zbit attenuator setting, and guard bit. Each word contains the following sequence: Table 1 - 14 Bit SPI Word Sequence D13 RX Path 2 bypass mode D12 Guard bit D11 RX Path 1 bypass mode D10 Guard bit D9 Attenuator 2 D8 Attenuator 2 D7 Attenuator 2 D6 Attenuator 2 D5 Guard bit D4 Attenuator 1 D3 Attenuator 1 D2 Attenuator 1 D1 Attenuator 1 D0 Guard bit Figure 1 - Serial Register Timing Diagram

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 8 Rev 1, April 2015 IDTF1130NBGI Datasheet Table 2 - SPI Preset Timing Parameters Calcuated for 24 MHz Parameter Symbol Min Typ Max Units Clock Period (Frequency) t p 41.66 (24) ns (MHz) Data Setup t ds 20.83 ns Data to CLK Setup Time t dcs 5 ns LE to CLK Setup Time t lcs 5 ns CLK to LE Setup Time t cls 5 ns LE Pulse Time t lew 20 ns Table 3 – Attenuator Data Word Bit Sequence Attenuation Setting Attenuator 1 D4, D3, D2, D1 Attenuator 2 D9, D8, D7, D6 Insertion Loss 0000 0000 2 dB 0001 0001 4 dB 0010 0010 6 dB 0011 0011 8 dB 0100 0100 10 dB 0101 0101 12 dB 0110 0110 14 dB 0111 0111 16 dB 1000 1000 18 dB 1001 1001 20 dB 1010 1010 22 dB 1011 1011 24 dB 1100 1100 26 dB 1101 1101 28 dB 1110 1110 30 dB 1111 1111 Table 4 - RF Bypass Data Word Bit Sequence RF Switch ByPass Mode RX1 D11 RX2 D13 OFF 0 0 ON 1 1

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 9 Rev 1, April 2015 IDTF1130NBGI Datasheet PIN 8 LATCH ENABLE (LE): When LE is high (> VIH), the CLK input is disabled. IDT recommends keeping LE high to reduce F1130 sensitivity to CLK bus noise when SPI is not being programmed. When LE is low (< VIL), the DATA word can be programmed into the shift registers. The programmed word is then latched into F1130 on the LE rising edge (refer to Figure 1). End of data occurs after 14 th bit. D EFAULT REGISTER SETTING : After power on, the default setting for the VGA is Bypass OFF mode with attenuation set to 30 dB. This means the amplifier is in the signal path with maximum attenuation. TYPICAL OPERATING CONDITIONS (TOC) Unless otherwise noted for the TOC graphs on the following pages, the following conditions apply.

VCC = +5.00 V
TCASE = +25 °C
FRF = 900 MHz
FIF = 199 MHz
FLO = 1100 MHz
PLO = 0 dBm
RF VGA output = -5 dBm/tone
RF Mixer output = 0 dBm/tone
Attenuator = 0 dB
STBY_A, STBY_B = GND

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 10 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA BYPASS OFF: TYPICAL OPERATING CONDITIONS (- 1 -) Gain vs. T case [GVGA ] Output IP3 vs. Tcase [OIP3 VGA ] Channel Isolation vs. T case & V cc [ISO A-B] Gain vs. Vcc [GVGA ] Output IP3 vs. Vcc [OIP3 VGA ] Channel Isolation vs. Tcase & V cc [ISO B-A] 400 500 600 700 800 900 1000 1100 Gain (dB) RF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 400 500 600 700 800 900 1000 1100 Channel Isolation (dBc) RF Frequency (MHz) -40 C / 4.75 V -40 C / 5.00 V -40 C / 5.25 V +25 C / 4.75 V +25 C / 5.00 V +25 C / 5.25 V +105 C / 4.75 V +105 C / 5.00 V +105 C / 5.25 V 400 500 600 700 800 900 1000 1100 Gain (dB) RF Frequency (MHz) +25 C / 4.75 V / CH A +25 C / 4.75 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +25 C / 5.25 V / CH A +25 C / 5.25 V / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) +25 C / 4.75 V / CH A +25 C / 4.75 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +25 C / 5.25 V / CH A +25 C / 5.25 V / CH B 400 500 600 700 800 900 1000 1100 Channel Isolation (dBc) RF Frequency (MHz) -40 C / 4.75 V -40 C / 5.00 V -40 C / 5.25 V +25 C / 4.75 V +25 C / 5.00 V +25 C / 5.25 V +105 C / 4.75 V +105 C / 5.00 V +105 C / 5.25 V

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 11 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA BYPASS OFF: TYPICAL OPERATING CONDITIONS (- 2 -) Gain Accuracy [DSA ACC 400 MHz] Gain Accuracy [DSA ACC 900 MHz] Gain Accuracy [DSA ACC 1100 MHz] OIP3 vs. Attenuation [400 MHz] OIP3 vs. Attenuation [900 MHz] OIP3 vs. Attenuation [1100 MHz] -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2 1.6 2.0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Error (dB) Attenuation (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2 1.6 2.0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Error (dB) Attenuation (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2 1.6 2.0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Error (dB) Attenuation (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -10 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output IP3 (dBm) Attenuation (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -10 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output IP3 (dBm) Attenuation (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -10 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output IP3 (dBm) Attenuation (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 12 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA BYPASS OFF: TYPICAL OPERATING CONDITIONS (- 3 -) Gain vs. Input Power [400 MHz] Gain vs. Input Power [900 MHz] Gain vs. Input Power [1100 MHz] OIP3 vs. Input Power [400 MHz] OIP3 vs. Input Power [900 MHz] OIP3 vs. Input Power [1100 MHz] -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 Gain (dB) Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 Gain (dB) Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 Gain (dB) Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 Outut IP3 (dBm) Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 Outut IP3 (dBm) Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 Outut IP3 (dBm) Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 13 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA BYPASS OFF: TYPICAL OPERATING CONDITIONS (- 4 -) Input Match – [S11 VGA ] Noise Figure [NF VGA ] Output Match – [S22 VGA ] -30 -25 -20 -15 -10 200 400 600 800 1000 1200 1400 Return Loss (dB) RF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 400 500 600 700 800 900 1000 1100 Noise Figure (dB) RF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B LO = 1100 MHz, 0 dB -30 -25 -20 -15 -10 200 400 600 800 1000 1200 1400 Return Loss (dB) RF Frequency (MHz) -40 C / 5.00 V / CH B -40 C / 5.00 V / CH A +25 C / 5.00 V / CH B +25 C / 5.00 V / CH A +105 C / 5.00 V / CH B +105 C / 5.00 V / CH A

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 14 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA BYPASS ON: TYPICAL OPERATING CONDITIONS (- 5 -) Gain vs. T case [GBYPASS ] Output IP3 vs.T case [OIP3 BYPASS_0 ] Channel Isolation vs. T case & V cc [ISO A-B] Gain vs. Vcc [GBYPASS ] Output IP3 vs.V cc [OIP3 BYPASS_0 ] Channel Isolation vs. T case & V cc [ISO B-A] 400 500 600 700 800 900 1000 1100 Gain (dB) RF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 400 500 600 700 800 900 1000 1100 Channel Isolation (dBc) RF Frequency (MHz) -40 C / 4.75 V -40 C / 5.00 V -40 C / 5.25 V +25 C / 4.75 V +25 C / 5.00 V +25 C / 5.25 V +105 C / 4.75 V +105 C / 5.00 V +105 C / 5.25 V 400 500 600 700 800 900 1000 1100 Gain (dB) RF Frequency (MHz) +25 C / 4.75 V / CH A +25 C / 4.75 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +25 C / 5.25 V / CH A +25 C / 5.25 V / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) +25 C / 4.75 V / CH A +25 C / 4.75 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +25 C / 5.25 V / CH A +25 C / 5.25 V / CH B 400 500 600 700 800 900 1000 1100 Channel Isolation (dBc) RF Frequency (MHz) -40 C / 4.75 V -40 C / 5.00 V -40 C / 5.25 V +25 C / 4.75 V +25 C / 5.00 V +25 C / 5.25 V +105 C / 4.75 V +105 C / 5.00 V +105 C / 5.25 V

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 15 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA BYPASS ON: TYPICAL OPERATING CONDITIONS (- 6 -) Gain Accuracy [DSA ACC 400 MHz] Gain Accuracy [DSA ACC 900 MHz] Gain Accuracy [DSA ACC 1100 MHz] OIP3 vs. Attenuation [400 MHz] OIP3 vs. Attenuation [900 MHz] OIP3 vs. Attenuation [1100 MHz] -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2 1.6 2.0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Error (dB) Attenuation Setting (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2 1.6 2.0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Error (dB) Attenuation Setting (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -2.0 -1.6 -1.2 -0.8 -0.4 0.0 0.4 0.8 1.2 1.6 2.0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Error (dB) Attenuation Setting (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output IP3 (dBm) Attenuation Setting (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output IP3 (dBm) Attenuation Setting (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Output IP3 (dBm) Attenuation Setting (dB) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 16 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA BYPASS ON: TYPICAL OPERATING CONDITIONS (- 7 -) Gain vs. Input Power [400 MHz] Gain vs. Input Power [900 MHz] Gain vs. Input Power [1100 MHz] OIP3 vs. Input Power [400 MHz] OIP3 vs. Input Power [900 MHz] OIP3 vs. Input Power [1100 MHz] -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 0 2 4 6 8 10 12 14 16 Gain (dB) RF Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 0 2 4 6 8 10 12 14 16 Gain (dB) RF Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -4.0 -3.5 -3.0 -2.5 -2.0 -1.5 -1.0 0 2 4 6 8 10 12 14 16 Gain (dB) RF Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 0 2 4 6 8 10 12 14 16 Output IP3 (dBm) RF Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 0 2 4 6 8 10 12 14 16 Output IP3 (dBm) RF Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B 0 2 4 6 8 10 12 14 16 Output IP3 (dBm) RF Input Power (dBm) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 17 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA BYPASS ON: TYPICAL OPERATING CONDITIONS (- 8 -) Input Match - S11 VGA Output Match - S22 VGA -30 -25 -20 -15 -10 200 400 600 800 1000 1200 1400 Return Loss (dB) RF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B -30 -25 -20 -15 -10 200 400 600 800 1000 1200 1400 Return Loss (dB) RF Frequency (MHz) -40 C / 5.00 V / CH B -40 C / 5.00 V / CH A +25 C / 5.00 V / CH B +25 C / 5.00 V / CH A +105 C / 5.00 V / CH B +105 C / 5.00 V / CH A

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 18 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 9 -) Gain vs. T case [GMXR, HS Injection] Gain vs. V cc [GMXR, HS Injection] Gain vs. LO Power [GMXR, HS Injection] Gain vs. T case [GMXR, LS Injection] Gain vs. V cc [GMXR, LS Injection] Gain vs. LO Power [GMXR, LS Injection] 400 500 600 700 800 900 1000 1100 Conversion Gain (dB) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Conversion Gain (dB) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Conversion Gain (dB) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B 400 500 600 700 800 900 1000 1100 Conversion Gain (dB) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Conversion Gain (dB) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Conversion Gain (dB) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 19 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 10 -) OIP3 vs. T case [OIP3 MXR, HS injection] OIP3 vs. V cc [OIP3 MXR , HS injection] OIP3 vs. LO Power [OIP3 MXR, HS injection] OIP3 vs. T case [OIP3 MXR, LS injection] OIP3 vs. V cc [OIP3 MXR, LS injection] OIP3 vs. LO Power [OIP3 MXR, LS injection] 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP3 (dBm) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 20 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 11 -) OIP2 vs. T case [OIP2MXR , HS injection] OIP2 vs. V cc [OIP2MXR, HS injection] OIP2 vs. LO Power [OIP2MXR , HS injection] OIP2 vs. T case [OIP2MXR , LS injection] OIP2 vs. V cc [OIP2MXR , LS injection] OIP2 vs. LO Power [OIP2MXR , LS injection] 400 500 600 700 800 900 1000 1100 Output IP2 (dBm) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP2 (dBm) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP2 (dBm) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP2 (dBm) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP2 (dBm) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Output IP2 (dBm) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 21 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 12 -) IP1dB vs. T case [IP1dB MXR , HS injection] IP1dB vs. V cc [IP1dB MXR , HS injection] IP1dB vs. LO Power [IP1dB MXR , HS injection] IP1dB vs. T case [IP1dB MXR , LS injection] IP1dB vs. V cc [IP1dB MXR , LS injection] IP1dB vs. LO Power [IP1dB MXR , LS injection] 400 500 600 700 800 900 1000 1100 Input P1dB (dBm) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Input P1dB (dBm) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Input P1dB (dBm) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B 400 500 600 700 800 900 1000 1100 Input P1dB (dBm) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Input P1dB (dBm) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Input P1dB (dBm) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 22 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 13 -) 2x2 Rejection vs. T case [2x2 MXR , HS rejection] 2x2 Rejection vs. V cc [2x2 MXR ,HS rejection] 2x2 Rejection vs. T case [2x2 MXR , LS rejection] 2x2 Rejection vs. V cc [2x2 MXR , LS rejection] -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 2x2 Spur (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 2x2 Spur (dBc) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 2x2 Spur (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 2x2 Spur (dBc) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 23 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 14 -) 3x3 Rejection vs. T case [3x3MXR , HS rejection] 3x3 Rejection vs. V cc [3x3MXR , HS rejection] 3x3 Rejection vs. T case [3x3MXR , LS rejection] 3x3 Rejection vs. V cc [3x3MXR , LS rejection] -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 3x3 Spur (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 3x3 Spur (dBc) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 3x3 Spur (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 3x3 Spur (dBc) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 24 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 15 -) HD2 vs. T case [HD2 MXR , HS injection] HD2 vs. V cc [HD2 MXR , HS injection] HD2 vs. LO Power [HD2 MXR , HS injection] HD2 vs. T case [HD2 MXR , LS injection] HD2 vs. V cc [HD2 MXR , LS injection] HD2 vs. LO Power [HD2 MXR , LS injection] -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 25 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 16 -) HD3 vs. T case [HD3 MXR , HS injection] HD3 vs. V cc [HD3 MXR , HS injection] HD3 vs. LO Power [HD3 MXR , HS injection] HD3 vs. T case [HD3 MXR , LS injection] HD3 vs. V cc [HD3 MXR , LS injection] HD3 vs. LO Power [HD3 MXR , LS injection] -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B -90 -80 -70 -60 -50 -40 -30 -20 -10 400 500 600 700 800 900 1000 1100 Harmonic (dBc) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 26 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 17 -) LO to IF Leakage vs. Tcase [ISO LI, HS injection] RF to IF Rejection vs. Tcase [ISO RI , HS injection] Channel Isolation vs. Tcase [ISO IF , HS injection] LO to IF Leakage vs. Tcase [ISO LI, LS injection] RF to IF Rejection vs. Tcase [ISO RI , LS injection] Channel Isolation vs. Tcase [ISO IF , LS injection] -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 400 500 600 700 800 900 1000 1100 LO to IF Leakage (dBc) LO Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 400 500 600 700 800 900 1000 1100 RF to IF Leakage (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Channel Isolation (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 400 500 600 700 800 900 1000 1100 LO to IF Leakage (dBc) LO Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 400 500 600 700 800 900 1000 1100 RF to IF Leakage (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Channel Isolation (dBc) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 27 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 18 -) IF Gain flatness vs. Tcase [GMXR_T , HS injection] IF Gain flatness vs. Vcc [GMXR_T , HS injection] IF Gain flatness vs. LO Power [GMXR_T , HS injection] IF Gain flatness vs. Tcase [GMXR_T , LS injection] IF Gain flatness vs. Vcc [GMXR_T , LS injection] IF Gain flatness vs. LO Power [GMXR_T , LS injection] 0 50 100 150 200 250 300 350 400 Gain (dB) IF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B LO = 1100 MHz 0 50 100 150 200 250 300 350 400 Gain (dB) IF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B LO = 1100 MHz 0 50 100 150 200 250 300 350 400 Gain (dB) IF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B LO = 1100 MHz 0 50 100 150 200 250 300 350 400 Gain (dB) IF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B LO = 700 MHz 0 50 100 150 200 250 300 350 400 Gain (dB) IF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B LO = 700 MHz 0 50 100 150 200 250 300 350 400 Gain (dB) IF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B LO = 700 MHz

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 28 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 19 -) Noise Figure vs.T case [NF MXR , HS Injection] Noise Figure vs.T case [NF MXR LS, Injection] Noise Figure with Blocker [NF MXR_BLK ] Mixer RF Input Return Loss [S11 MXR_RF] Mixer LO Port Return Loss [S11 MXR_LO ] Mixer IF Output Return Loss [S22 MXR_IF ] 400 500 600 700 800 900 1000 1100 Noise Figure (dB) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 400 500 600 700 800 900 1000 1100 Noise Figure (dB) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B -20 -15 -10 -5 0 5 10 NF(dB) Blocker Level (dBm) LO = 1100 MHz, 0 dBm RF = 900 MHz Blocker = 825 MHz Vcc = 5.0 V, Tc=25C -40 -35 -30 -25 -20 -15 -10 300 400 500 600 700 800 900 1000 1100 1200 Return Loss (dB) RF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B LO = 1255 MHz, 0 dBm -30 -25 -20 -15 -10 400 500 600 700 800 900 1000 1100 1200 1300 1400 Return Loss (dB) Frequency (MHz) +25 C / 5.00 V / -3 dBm +25 C / 5.00 V / 0 dBm +25 C / 5.00 V / +3 dBm -30 -25 -20 -15 -10 0 100 200 300 400 500 Return Loss (dB) IF Frequency (MHz) -40 C / 5.00 V / CH A -40 C / 5.00 V / CH B +25 C / 5.00 V / CH A +25 C / 5.00 V / CH B +105 C / 5.00 V / CH A +105 C / 5.00 V / CH B LO = 1255 MHz, 0 dBm

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 29 Rev 1, April 2015 IDTF1130NBGI Datasheet M IXER : TYPICAL OPERATING CONDITIONS (- 20 -) Current Consumption vs. Tcase [HS injection] Current consumption vs. Vcc [HS injection] Current consumption vs. LO Power [HS injection] Current consumption vs. Tcase [LS injection] Current consumption vs. Vcc [LS injection] Current consumption vs. LO Power [LS injection] 0.30 0.32 0.34 0.36 0.38 0.40 400 500 600 700 800 900 1000 1100 Current (A) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 0.30 0.32 0.34 0.36 0.38 0.40 400 500 600 700 800 900 1000 1100 Current (A) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 0.30 0.32 0.34 0.36 0.38 0.40 400 500 600 700 800 900 1000 1100 Current (A) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B 0.30 0.32 0.34 0.36 0.38 0.40 400 500 600 700 800 900 1000 1100 Current (A) RF Frequency (MHz) -40 C / 5.00 V / 0 dBm / CH A -40 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +105 C / 5.00 V / 0 dBm / CH A +105 C / 5.00 V / 0 dBm / CH B 0.30 0.32 0.34 0.36 0.38 0.40 400 500 600 700 800 900 1000 1100 Current (A) RF Frequency (MHz) +25 C / 4.75 V / 0 dBm / CH A +25 C / 4.75 V / 0 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.25 V / 0 dBm / CH A +25 C / 5.25 V / 0 dBm / CH B 0.30 0.32 0.34 0.36 0.38 0.40 400 500 600 700 800 900 1000 1100 Current (A) RF Frequency (MHz) +25 C / 5.00 V / -3 dBm / CH A +25 C / 5.00 V / -3 dBm / CH B +25 C / 5.00 V / 0 dBm / CH A +25 C / 5.00 V / 0 dBm / CH B +25 C / 5.00 V / +3 dBm / CH A +25 C / 5.00 V / +3 dBm / CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 30 Rev 1, April 2015 IDTF1130NBGI Datasheet VGA & M IXER : TYPICAL OPERATING CONDITIONS (- 21 -) RF Amplifier to Mixer Isolation -70 -65 -60 -55 -50 -45 -40 300 400 500 600 700 800 900 1000 1100 1200 Isolation (dB) RF Frequency (MHz) Bypass OFF - CH A Bypass OFF - CH B Bypass ON - CH A Bypass ON - CH B

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 31 Rev 1, April 2015 IDTF1130NBGI Datasheet PACKAGE D RAWING (7mm x 7mm 48zpin TQFN), Use Exposed PAD (EPAD) Option P1 All dimenision are in mm.

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 32 Rev 1, April 2015 IDTF1130NBGI Datasheet LAND PATTERN D IMENSION

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 33 Rev 1, April 2015 IDTF1130NBGI Datasheet PIN D IAGRAM

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 34 Rev 1, April 2015 IDTF1130NBGI Datasheet PIN D ESCRIPTION Pin Name Function 1, 12, 23, 32, 38 VCC Power Supply. Bypass to GND with capacitors shown in the Typical Application Circuit as close as possible to pin. 46, 48 GND Ground these pins. 3 RFIN_A ChannelzA VGA RF Input. Internally matched to 50Ω. AC coupled. DO NOT apply DC to this pin. Place coupling capacitor as close to the pin as possible.

5 RFAMP_BIAS Connect a resistor to GND (refer to BO M)

6 SPI Data Data: 1.8V CMOS compatible. 7 SPI CLK Clock: 1.8V CMOS compatible. 8 SPI LE Latch Enable: 1.8V CMOS compatible. See Ser ial Interface Section for pin description. 10 RFIN_B ChannelzB VGA RF Input. Internally matched to 50Ω. AC couple d. DO NOT apply DC to this pin. Place coupling capacitor as close to the pin as possible. 14 RFB_BIAS Connect a resistor to GND (refer to BOM ). 16 RFOUT_B ChannelzB VGA RF Output. Internally matched to 50Ω. AC coupled. DO NOT apply DC to this pin. Place coupling capacitor as close to the pin as possible. 21 MIXRFIN_B ChannelzB Mixer RF Input. Internally m atched to 50Ω. DO NOT apply DC to this pin. 24 IFB_BIAS Connect a resistor to GND (refer to BOM ).

25 STBY_B Standby Diversity Channel (Low = device power ON, High or Floating = device power

OFF with SPI still powered ON) 26 IFOUT_B+ ChannelzB Mixer Differential IFz Output. Connect pullup inductor from this pin to VCC. 27 IFOUT_Bz ChannelzB Mixer Differential IF+ Output. Connect pullup inductor from this pin to VCC. 29 LO_BIAS Connect a resistor to GND (refer to BOM) . 30 LO_IN Mixer Local Oscillator Input. Connect the LO to this port through the recommended coupling capacitor. 34 IFOUT_Az ChannelzA Mixer Differential IFz Output. Connect pullup inductor from this pin to VCC. 35 IFOUT_A+ ChannezAl Mixer Differential IF+ Output. Connect pullup inductor from this pin to VCC.

36 STBY_A Standby Main Channel (Low = device power ON, High = device power OFF with SPI

still powered ON). 37 IFA_BIAS Connect a resistor to GND (refer to BOM ). 40 MIXRFIN_A ChannelzA Mixer RF Input. Internally m atched to 50Ω. DO NOT apply DC to this pin. 45 RFOUT_A ChannelzA RF VGA Output. Internally matched to 50Ω. AC coupled. DO NOT apply DC to this pin. Place coupling capacitor as close to the pin as possible. 47 RFA_BIAS Connect a resistor to GND (refer to BOM ). — EP Exposed Pad. Internally connected to GND. Solder this exposed pad to a PCB pad that uses multiple ground vias to provide heat transfer out of the device into the PCB ground planes. These multiple via grounds are also required to achieve the noted RF performance.

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 35 Rev 1, April 2015 IDTF1130NBGI Datasheet EVK IT PICTURE Channel B No Connection – Standby Connection z On Channel A No Connection – Standby Connection z On SPI Pins GND CSb Data Clk GND GND GND GND DC Power Connections to package pins and IF R18 Pin 1 R17 Pin 12 R11 Pin 23 R12 IF B Bias R13 Pin 32 R14 IF A Bias R15 Pin 38

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 36 Rev 1, April 2015 IDTF1130NBGI Datasheet EV KIT / APPLICATIONS CIRCUIT

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 37 Rev 1, April 2015 IDTF1130NBGI Datasheet EVK IT BOM Item # Part Reference QTY DESCRIPTION Mfr. Part # Mfr.

1 C2, 8, 14, 17, 20,

26, 28, 34 8 CAP CER 10000PF 16V 10% X7R 0402 GRM155R71C103KA 01D MuRata

2 C1, 9, 15, 18, 21,

27, 29, 35 8 CAP CER 0.1UF 16V 10% X7R 0402 GRM155R71C104KA88D MuRata

3 C3, 7, 12, 19, 31 5 CAP CER 200PF 50V 5% C0G 0402 GRM1555C1H201JA01D MuRata

4 C22 z25 4 CAP CER 1000PF 50V C0G 0402 GRM1555C1H102JA01D MuRata

5 C13, 30 2 CAP CER 8PF 50V C0G 0402 GRM1555C1H8R0DZ01D MuRata

6 R2 1 RES 7.50K OHM 1/10W 1% 0402 SMD ERJ z2RKF7501X Panasonic 7 R3, 5, 6 3 RES 3.00K OHM 1/10W 1% 0402 SMD ERJ z2RKF3001X Panasonic 8 R19, 26, 33 3 RES 3.24K OHM 1/10W 1% 0402 SMD ERJ z2RKF3241X Panasonic 9 R22, 30 2 RES 62.0 OHM 1/10W 1% 0402 SMD ERJ z2RKF62R0X Panasonic

10 R11 z15, 17, 18,

24, 25, 27, 28 11 RES 0.0 OHM 1/10W 0402 SMD ERJz2GE0R00X Panason ic

11 L1, 2, 10, 11 4 0805LS (2012) Ceramic Chip Inductor 0805LS z102XJLB Coilcraft

12 R21, 31 2 0402CS Ceramic Chip Inductor 0402CS z20NXJLU Coilcraft

13 T1, 2 2 4:1 Center Tap Balun TC4 z1TG2+ Mini Circuits

14 J11, 2, 14 3 CONN HEADER VERT SGL 2POS GOLD 961102 z6404 zAR 3M

15 J10 1 CONN HEADER VERT DBL 4POS GOLD 67997 z108HLF FCI

16 J15 1 CONN HEADER VERT DBL 7POS GOLD 67996 z114HLF FCI

17 J1 z4, 6, 8, 9 7 SMA_END_LAUNCH (Big) 142 z0701 z851 Emerson Johnson

18 J5, 7, 13 3 SMA_END_LAUNCH (Small) 142 z0711 z821 Emerson Johnson

19 U1 1 Dual Path RF Receiver 400 z1100MHz AV650B00_5ZNA IDT

20 1 Printed Cicuit Board F1130 EVKIT REV 01

21 Bill Of Material

R1, 7z10, 20, 23, 29, 32

0 Do Not Populate N/A N/A

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 38 Rev 1, April 2015 IDTF1130NBGI Datasheet A PPLICATIONS INFORMATION F1130 has been optimized for use in high performance RF applications from 1400 MHz to 2700 MHz. Power Supplies A common VCC power supply should be used for all pins requiring DC power. All supply pins should be bypassed with external capacitors to minimize noise and fast transients. Supply noise can degrade noise figure and fast transients can trigger ESD clamps and cause them to fail. Supply voltage change or transients should have a slew rate smaller than 1V/20uS. In addition, all control pins should remain at 0V (+/z0.3V) while the supply voltage ramps or while it returns to zero. Control Pin Interface If control signal integrity is a concern and clean signals cannot be guaranteed due to overshoot, undershoot, ringing, etc., the following circuit at the input of each control pin is recommended. This applies to SPI and control pins 6, 7, 8, 25, and 36 as shown below. Note the recommended resistor and capacitor values do not necessarily match the EV kit BOM for the case of poor control signal integrity. For multiple devices driven by a single control line, the component values will need to be adjusted accordingly so as not to overload the control line.

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz Glitch-Free TM , RF Receiver 39 Rev 1, April 2015 IDTF1130NBGI Datasheet F1130 Digital Pin Voltage & Resistance Values (pins not connected) The following table list the resitance between various pins and ground when no DC power is applied. When the device is powered up with +5 Volts DC these same pins to should have the measured voltage to ground. Pin Name DC voltage (volts) Resistance (ohms)

6 DATA 5 57K

7 CLK 5 57K

8 LE 5 57K

25 STBY_B 5 57K

36 STBY_A 5 57K

TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com Contact Information For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) © 2020 Renesas Electronics Corporation. All rights reserved.

Product Information

F1180 specifications and overview.

Summary

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz

Description

Dual Path Lowband RF Receiver 400 MHz to 1100 MHz

Source title F1180 Datasheet(PDF) - Integrated Device Technology

Related Parts

More parts from the same family.

Browse manufacturer