F1162NBGI

Renesas Technology Corp

RF to IF Dual Downconverting Mixer Rev1, July 2012

Manufacturer: Renesas Technology Corp

Document: 27 Pages / 3Mb

Request Quote Download Datasheet Read online HTML view

More from Renesas Technology Corp Browse F parts

Online Datasheet

Read F1162NBGI online.

F1162 RENESAS | Alldatasheet

Document overview

Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 27

Technical content

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 1 Rev1, July 2012 DATASHEET GENERAL D ESCRIPTION This document describes the specifications for the I DTF1162 Zero,DistortionTM RF to IF Downconverting M ixer. This device is part of a series of mixers offered with high side or low side injection options for all UTRA bands. See the Part# Matrix for the details of all devices in this series. The F1162 dual channel device is designed to operate with a single 5V supply. It is optimized for operation in a Multi,mode, Multi,carrier BaseStation Receiver for RF bands from 2300 , 2700 MHz with Low Side or High Side Injection. IF frequencies from 50 to 500 MHz are supported. Nominally, the device offers +43 dBm Output IP3 with 330 mA of ICC. Alternately one can a djust 4 resistor values and a toggle pin to run the device in low current mode with +38 dBm Output IP3 and 230 mA of ICC. COMPETITIVE ADVANTAGE In typical basestation receivers the RF to IF mixer d ominates the linearity performance for the entire receive system. The Zero,DistortionTM family of mixers d ramatically improve the maximum signal levels (IM3 t ones) that the BTS can withstand at a desired Signal to Noise Ratio (SNR.) Alternately, one can run the device in Low Current Mode to reduce Power consumption significantly. Zero,DistortionTM technology allows r ealization of either benefit. /checkbld IP3O: ⇑⇑ ⇑⇑ 11 dB STD Mode, ⇑⇑ ⇑⇑ 5 dB LC Mode /checkbld Dissipation: ⇓⇓ ⇓⇓ 40% LC, ⇓⇓ ⇓⇓ 15% STD Mode /checkbld Allows for higher RF gain improving Sensitivity PART# MATRIX Part# RF freq r ange UTRA bands IF freq range Typ. Gain Injection F1100 698 - 915 5,6,8,12,13,14,17 ,19,20 50 - 450 8.5 High Side F1102 698 - 915 5,6,8,12,13,14,17 ,19,20 50 - 250 8.5 Both F1150 1700 - 2200 1,2,3,4,9,10, 33, 34,35, 36, 37,39 50 - 450 8.5 High Side F1152 1400 - 2200 1,2,3,4,9,10,111, 21 1, 241, 33, 34,35, 36, 37,39 50 - 350 8.5 Low Side FF11116622 22 33 0000 –– 22 770000 77,,33 88,,4400,,4411 5500 –– 550000 88..99 BB ootthh F EATURES

D ual Path for Diversity Systems
Ideal for Multi,Carrier Systems
8.9 dB Gain
Ultra linear ++ 4433 ddBB mm IIPP33OO
• Low NF < 10 dB
20 0 Ω output impedance
Ultra high +13 dBm P1dBI
PPiinn CCoommppaattiibbllee w /existing solutions
6x6 36 pin package
CCoonnssttaanntt LLOO PPoorrtt ZZ iinn SSTTBB YY mmooddee
< 200 nsec settling from Power Down
Low Current Mode : IICCCC == 223300 mmAA
St andard Mode: ICC = 330 mA
N OTE production BOM on p. 25 D EVICE BLOCK DIAGRAM O RDERING INFORMATION – with High side injection RFIN_A IFOUT_A RF VCO LOISET LCMODE RFIN_B IFOUT_B Bias Control STBY IDTF1162NBGI8 0.8 mm height package Green Industrial Temp range Tape & Reel Omit IDT prefix RF product Line

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 2 Rev1, July 2012 DATASHEET ABSOLUTE MAXIMUM RATINGS VCC to GND ,0.3V to +5.5V STBY, LCMODE ,0.3V to (VCC_ + 0.3V) IF_A+, IF_B+, IF_A,, IF_B,, LO1_ADJ, LO2_ADJ ,0.3V to (VCC_ + 0.3V) LO_IN, LO_IN_ALT, RF_A, RF_B ,0.3V to +0.3V IF_BiasA, IF_BiasB to GND ,0.3V to +0.3V RF Input Power (RF_IN[A+, A,, B+, B,]) +20dBm Continuous Power Dissipation 2.2W θJA (Junction – Ambient) +35°C/W θJC (Junction – Case) The Case is defined as the exposed paddle +2.5°C/W Operating Temperature Range (Case Temperature) TC = ,40°C to +100°C Maximum Junction Temperature 150°C Storage Temperature Range ,65°C to +150°C Lead Temperature (soldering, 10s) . +260°C Stresses above those listed above may cause permanen t damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 3 Rev1, July 2012 DATASHEET I DTF1162 SPECIFICATION S pecifications apply at VCC = +5.00V, TC = +25°C FRF = 2600 MHz , FIF = 400MHz , Low Side Injection, PLO = 0 dBm, STBY = GND, LCMODE = VIH (STD Mode), EVKit BOM = Standard Mode, Transformer Loss included (not de)embedded) unless otherwise noted. Parameter Comment Symbol min typ max units Logic Input High For Standby, LCMODE Pins VIH 2 V Logic Input Low For Standby, LCMODE Pins VIL 0 .8 V Logic Current For Standby Pin IIH, IIL P30 +30 µA Logic Current For LCMODE Pin IIH, IIL P100 P20 µA Supply Voltage(s) All V CC pins VCC 4 .75 to 5.25 V Operating Temperature Range Case Temperature T CASE ) 40 to +100 degC Supply Current Total VCC , STD Mode /square4Total Both Channels ISTD 330 3 751 mA Supply Current Total VCC , LC Mode /square4LCMODE = GND /square4EVkit BOM = LC Mode /square4Total Both Channels ILC 2 30 260 mA Supply Current Standby Mode /square4STBY = VIH /square4LCMODE > VIH (STD Mode) /square4Total Both Channels ISTBY 2 3 30 mA RF Freq Range Operating Range FRF 2 300 to

2700 MHz

IF Freq Range Operating Range FIF 50 to 500 MHz LO Freq Range Operating Range FLO 1 800 to

2900 MHz

LO Power Operating Range PLO )6 to +6 dBm RF Input Impedance Single Ended Return Loss ~20 dB ZRF 50 Ω IF Output Impedance Differential Return Loss ~ 15 dB ZIF 200 Ω LO port Impedance Single Ended Return Loss ~15 dB ZLO 50 Ω Settling Time

Pin = )13 dBm
Gate STBY from VIH to VIL
Time for IF Signal to settle to within 0.1 dB of final value TSETT 0.150 µsec Gain STD Mode Conversion Gain
FRF = 2300 MHz
LCMODE = VIH
EVkit BOM = STD Mode
FIF = 400 MHz (Low Side Inj.) GSTD 7.2 8.4 9.6 dB

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 4 Rev1, July 2012 DATASHEET I DTF1162 SPECIFICATION (CONTINUED ) Parameter Comment Symbol min typ max units Gain LC Mode Conversion Gain

FRF = 2700 MHz
LCMODE = GND
EVkit BOM = LC Mode
FIF = 200 MHz (High Side Inj.) GLC 6.8 7.9 9.0 dB NF STD Mode Noise Figure
RF trace de)embedded
FIF = 200 MHz NFSTD 9.9 dB NF LC Mode Noise Figure
RF trace de)embedded
LCMODE = GND, EVKit BOM = LC
FIF = 200 MHz NFLC 9.7 dB NF w/Blocker /square4+100 MHz offset blocker /square4PBLOCKER = +10 dBm /square4FIF = 250 MHz NFBLK 23.5 dB Output IP3 – STD mode /square4PIN = )10 dBm per tone /square4800 KHz Tone Separation IP3O1 382 4 3 dBm Output IP3 – LC mode /square4PIN = )10 dBm per tone /square4FIF = 200 MHz (Low Side Inj.) /square4FRF = 2600 MHz /square4800 KHz Tone Separation /square4LCMODE = GND /square4EVKit BOM = LC Mode IP3O3 33.5 37.7 dBm Output IP3 – High Side Injection /square4PIN = )10 dBm per tone /square4800 KHz Tone Separation /square4FIF = 154 MHz (High Side Inj.) /square4FRF = 2600 MHz /square4Modified LC mode BOM (p. 26) IP3O2 43 dBm 2RF – 2LO rejection /square4PIN = )10 dBm /square4Frequency = FRF ) ½ FIF 2x2 )68 dBc 1 dB Compression – STD Mode /square4Input referred /square4400 MHz IF P1dBI1 11 11.9 dBm 1 dB Compression – LC Mode /square4LCMODE = GND /square4EVKit BOM = LC Mode /square4FIF = 200 MHz (Low Side Inj.) P1dBI2 8 10.2 dBm Gain Comp. w/blocker /square4Blocker /barb2right unmodulated tone /square4PIN = +8 dBm, +100 MHz offset /square4Signal Pin Tone = )20 dBm /square4Measure ∆G of signal /square4FIF = 250 MHz ∆GAC 0.15 dB Channel Isolation IF_B Pout vs. IF_A w/ RF_A input ISOC 63 dB LO to IF leakage LO Frequency = 2200 MHz ISOLI )32 )23 dBm RF to IF leakage Pin = )10 dBm ISORI )57 )43 dBm LO to RF leakage • LO Frequency = 2345 MHz
Low Current Mode ISOLR )41 dBm 1 – Items in min/max columns in bold italics are Guaranteed by Test 2 – All other Items in min/max columns are Guaranteed by Design Characterization

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 5 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDTIONS Unless otherwise Noted, the following Apply to the Typ Ops Graphs /square4800 KHz Tone Spacing /square4Low Side injection graphs with 200MHz & 400MHz IF (pages 6 – 14) /square4High Side injection graphs with 200MHz & 154MHz IF (pages 15 – 17) /square4Average of Channel A & Channel B /square4Pin = – 10 dBm per Tone /square4LO port = Pin 19 (Main Port) /square4Listed Temperatures are Case Temperature (TC = Case Temperature) /square4Where noted, TA or TAMB = Ambient Temperature

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 6 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-1-) G ain vs. TCASE Gain vs. LO Level O utput IP3 vs. VCC G ain vs. VCC Output IP3 vs. TCASE Output IP3 vs. LO Level Gain (dB) RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC -0 dBm -5.00 V -STD 25 degC -0 dBm -5.00 V -LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC Gain (dB) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC Output IP3 (dBm) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC -0 dBm -5.00 V -STD 25 degC -0 dBm -5.00 V -LC 25 degC -0 dBm -4.75 V -STD 25 degC -0 dBm -4.75 V -LC Gain (dB) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD25 degC - 0 dBm - 4.75 V - LC Output IP3 (dBm) RF Freq (Hz) -40 degC - 0 dBm - 5.00 V - STD-40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC -0 dBm -5.00 V -STD 100 degC -0 dBm -5.00 V -LC Output IP3 (dBm) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD25 degC - -3 dBm - 5.00 V - LC

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 7 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-2-) P 1dB vs. TCASE P1dB vs. LO Level RF x 2LO Rejection vs. VCC P 1dB vs. VCC 2RF x 2LO rejection vs. TCASE 2RF x 2LO Rejection vs. LO Level Input P1dB (dBm) RF Freq (Hz) -40 degC - 0 dBm - 5.00 V - STD-40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC -0 dBm -5.00 V -STD 100 degC -0 dBm -5.00 V -LC Input P1dB (dBm) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10

2 X 2 Rejection [Pin = -10] (dBc)

RF Freq (Hz) 25 degC - 5.25 V - 0 dBm - STD25 degC - 5.25 V - 0 dBm - LC 25 degC - 5.00 V - 0 dBm - STD25 degC - 5.00 V - 0 dBm - LC 25 degC - 4.75 V - 0 dBm - STD25 degC - 4.75 V - 0 dBm - LC Input P1dB (dBm) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC -0 dBm -4.75 V -STD 25 degC -0 dBm -4.75 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) -40 degC - STD - 5.00 V - 0 dBm-40 degC - LC - 5.00 V - 0 dBm 25 degC - STD - 5.00 V - 0 dBm25 degC - LC - 5.00 V - 0 dBm 100 degC - STD - 5.00 V - 0 dBm100 degC - LC - 5.00 V - 0 dBm -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) 25 degC - 5.00 V - 6 dBm - STD25 degC - 5.00 V - 6 dBm - LC 25 degC - 5.00 V - 0 dBm - STD25 degC - 5.00 V - 0 dBm - LC 25 degC -5.00 V --3 dBm -STD 25 degC -5.00 V --3 dBm -LC

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 8 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-3-) ICC vs. TCASE ICC vs. LO Level LO-IF Leakage vs. VCC ICC vs. VCC LO-IF Leakage vs. TCASE LO-IF Leakage vs. LO Level 0.200 0.220 0.240 0.260 0.280 0.300 0.320 0.340 0.360 0.380 0.400 Total ICC(Amps) RF Freq (Hz) -40 degC - 0 dBm - 5.00 V - STD-40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC 0.200 0.220 0.240 0.260 0.280 0.300 0.320 0.340 0.360 0.380 0.400 ICC(Amps) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD25 degC - -3 dBm - 5.00 V - LC -50 -45 -40 -35 -30 -25 -20 -15 -10 LO to IF Leakage (dBm) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC -0 dBm -5.00 V -STD 25 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 4.75 V - STD25 degC - 0 dBm - 4.75 V - LC 0.200 0.220 0.240 0.260 0.280 0.300 0.320 0.340 0.360 0.380 0.400 ICC(Amps) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD25 degC - 0 dBm - 4.75 V - LC -50 -45 -40 -35 -30 -25 -20 -15 -10 LO to IF Leakage (dBm) RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC -0 dBm -5.00 V -STD 100 degC -0 dBm -5.00 V -LC -50 -45 -40 -35 -30 -25 -20 -15 -10 LO to IF Leakage (dBm) RF Freq (Hz) 25 degC -6 dBm -5.00 V -STD 25 degC -6 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 9 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-4-) R F-IF Leakage vs. TCASE RF-IF Leakage vs. LO Level RF X 3LO Rejection vs. VCC R F-IF Leakage vs. VCC 3RF X 3LO Rejection vs. TCASE 3RF X 3LO Rejection vs. LO Level -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 RF to IF Leakage [Pin = -10] (dBm) RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC -0 dBm -5.00 V -STD 100 degC -0 dBm -5.00 V -LC -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 RF to IF Leakage [Pin = -10] (dBm) RF Freq (Hz) 25 degC -6 dBm -5.00 V -STD 25 degC -6 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 3 x 3 Rejection [Pin =-10] (dBc) RF Freq (Hz) 25 degC - 5.25 V - 0 dBm - STD25 degC - 5.25 V - 0 dBm - LC 25 degC - 5.00 V - 0 dBm - STD25 degC - 5.00 V - 0 dBm - LC 25 degC -4.75 V -0 dBm -STD 25 degC -4.75 V -0 dBm -LC -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 RF to IF Leakage [Pin = -10] (dBm) RF Freq (Hz) 25 degC -0 dBm -5.25 V -STD 25 degC -0 dBm -5.25 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC -0 dBm -4.75 V -STD 25 degC -0 dBm -4.75 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10

3 X 3 Rejection [Pin = -10] (dBc)

RF Freq (Hz) -40 degC - 5.00 V - 0 dBm - STD-40 degC - 5.00 V - 0 dBm - LC 25 degC - 5.00 V - 0 dBm - STD25 degC - 5.00 V - 0 dBm - LC 100 degC -5.00 V -0 dBm -STD 100 degC -5.00 V -0 dBm -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) 25 degC - 5.00 V - 6 dBm - STD25 degC - 5.00 V - 6 dBm - LC 25 degC - 5.00 V - 0 dBm - STD25 degC - 5.00 V - 0 dBm - LC 25 degC -5.00 V --3 dBm -STD 25 degC -5.00 V --3 dBm -LC

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 10 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-5-) C hannel Isolation vs. TCASE Channel Isolation vs. LO Level N oise Figure vs. TCASE (STD Mode) C hannel Isolation vs. VCC Noise Figure vs. TCASE (LC Mode) NF vs. Blocker (RF =2600 MHz, IF = 250 MHz, TA = 25C) Channel Isolation (dBc) RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC Channel Isolation (dBc) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 2300 2400 2500 2600 2700 Noise Figure [IF = 200 MHz] (dB) RF Frequency (MHz) -40 degC - ChA -40 degC - ChB 25 degC -ChA 25 degC -ChB 100 degC - ChA 100 degC - ChB RF trace losses de-embedded Channel Isolation (dBc) RF Freq (Hz) 25 degC -0 dBm -5.25 V -STD 25 degC -0 dBm -5.25 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD25 degC - 0 dBm - 4.75 V - LC 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 2300 2400 2500 2600 2700 Noise Figure [IF = 200 MHz] (dB) RF Frequency (MHz) -40 degC - ChA -40 degC - ChB 25 degC -ChA 25 degC -ChB 100 degC - ChA 100 degC - ChB RF trace losses de-embedded -30 -26 -22 -18 -14 -10 -6 -2 2 6 10 Noise Figure (dB) Blocker Input Power (dBm) ChA STD ChB STD ChA LC ChB LC

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 11 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 400 MHz, Low Side Injection] (-6-) G ain vs. TCASE Gain vs. LO Level O utput IP3 vs. VCC (EVKIT DE-EMBEDDED ) G ain vs. TCASE (EVKIT DE-EMBEDDED ) Output IP3 vs. TCASE (EVKIT DE-EMBEDDED ) Output IP3 vs. LO Level (EVKIT DE-EMBEDDED ) Gain (dB) RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC -0 dBm -5.00 V -STD 25 degC -0 dBm -5.00 V -LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC Gain (dB) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD25 degC - -3 dBm - 5.00 V - LC Output IP3 (dBm) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD25 degC - 0 dBm - 4.75 V - LC EVkit effects dePembedded, corrected for:

TC4P1T transformer loss (p. 19 middle right graph) Gain (dB) RF Freq (Hz) -40 degC - 0 dBm - 5.00 V - STD-40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC EVkit effects dePembedded, corrected for:
TC4P1T transformer loss (p. 19 middle right graph)
RF input trace loss (p. 19 middle left graph) Output IP3 (dBm) RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC EVkit effects dePembedded, corrected for:
TC4P1T transformer loss (p. 19 middle right graph) Output IP3 (dBm) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC EVkit effects dePembedded, corrected for:
TC4P1T transformer loss (p. 19 middle right graph)

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 12 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 400 MHz, Low Side Injection] (-7-) P 1dB vs. TCASE P1dB vs. LO Level RF x 2LO Rejection vs. VCC P 1dB vs. VCC 2RF x 2LO rejection vs. TCASE 2RF x 2LO rejection vs. LO Level Input P1dB (dBm) RF Freq (Hz) -40 degC - 0 dBm - 5.00 V - STD-40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC Input P1dB (dBm) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) 25 degC -0 dBm -5.25 V -STD 25 degC -0 dBm -5.25 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC -0 dBm -4.75 V -STD 25 degC -0 dBm -4.75 V -LC Input P1dB (dBm) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC -0 dBm -4.75 V -STD 25 degC -0 dBm -4.75 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC -0 dBm -5.00 V -STD 100 degC -0 dBm -5.00 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10

2 X 2 Rejection [Pin = -10] (dBm)

RF Freq (Hz) 25 degC -6 dBm -5.00 V -STD 25 degC -6 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 13 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 400 MHz, Low Side Injection] (-8-) ICC vs. TCASE ICC vs. LO Level LO-IF Leakage vs. VCC ICC vs. VCC LO-IF Leakage vs. TCASE LO-IF Leakage vs. LO Level 0.200 0.220 0.240 0.260 0.280 0.300 0.320 0.340 0.360 0.380 0.400 Total ICC(Amps) RF Freq (Hz) -40 degC - 0 dBm - 5.00 V - STD-40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC 0.200 0.220 0.240 0.260 0.280 0.300 0.320 0.340 0.360 0.380 0.400 ICC(Amps) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD25 degC - -3 dBm - 5.00 V - LC -50 -45 -40 -35 -30 -25 -20 -15 -10 LO to IF Leakage (dBm) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC -0 dBm -5.00 V -STD 25 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 4.75 V - STD25 degC - 0 dBm - 4.75 V - LC 0.200 0.220 0.240 0.260 0.280 0.300 0.320 0.340 0.360 0.380 0.400 ICC(Amps) RF Freq (Hz) 25 degC - 0 dBm - 5.25 V - STD25 degC - 0 dBm - 5.25 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 4.75 V - STD25 degC - 0 dBm - 4.75 V - LC -50 -45 -40 -35 -30 -25 -20 -15 -10 LO to IF Leakage (dBm) RF Freq (Hz) -40 degC - 0 dBm - 5.00 V - STD-40 degC - 0 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC - 0 dBm - 5.00 V - STD100 degC - 0 dBm - 5.00 V - LC -50 -45 -40 -35 -30 -25 -20 -15 -10 LO to IF Leakage (dBm) RF Freq (Hz) 25 degC - 6 dBm - 5.00 V - STD25 degC - 6 dBm - 5.00 V - LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC - -3 dBm - 5.00 V - STD25 degC - -3 dBm - 5.00 V - LC

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 14 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [IF = 400 MHz, Low Side Injection] (-9-) R F-IF Leakage vs. TCASE RF-IF Leakage vs. LO Level RF X 3LO Rejection vs. VCC R F-IF Leakage vs. VCC 3RF X 3LO Rejection vs. TCASE 3RF X 3LO Rejection vs. LO Level -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 RF to IF Leakage [Pin = -10] (dBm) RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC -0 dBm -5.00 V -STD 100 degC -0 dBm -5.00 V -LC -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 RF to IF Leakage [Pin = -10] (dBm) RF Freq (Hz) 25 degC -6 dBm -5.00 V -STD 25 degC -6 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) 25 degC -0 dBm -5.25 V -STD 25 degC -0 dBm -5.25 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC -0 dBm -4.75 V -STD 25 degC -0 dBm -4.75 V -LC -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 RF to IF Leakage [Pin = -10] (dBm) RF Freq (Hz) 25 degC -0 dBm -5.25 V -STD 25 degC -0 dBm -5.25 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC -0 dBm -4.75 V -STD 25 degC -0 dBm -4.75 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) -40 degC -0 dBm -5.00 V -STD -40 degC -0 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 100 degC -0 dBm -5.00 V -STD 100 degC -0 dBm -5.00 V -LC -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) 25 degC -6 dBm -5.00 V -STD 25 degC -6 dBm -5.00 V -LC 25 degC - 0 dBm - 5.00 V - STD25 degC - 0 dBm - 5.00 V - LC 25 degC --3 dBm -5.00 V -STD 25 degC --3 dBm -5.00 V -LC

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 15 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [High Side Injection see LC mode modifications on p. 25 ] (-10-) G ain vs. TCASE (EVKIT DE-EMBEDDED ) Output IP3 vs. TCASE P1dB vs. TCASE G ain vs. LO Level (EVKit de-embedded) Output IP3 vs. LO Level P1dB vs. LO Level Gain (dB) RF Freq (Hz) -40 degC - 0 dBm - STD - 2.0E+8Hz IF -40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF 25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 100 degC - 0 dBm - STD - 2.0E+8Hz IF 100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF EVkit effects dePembedded, corrected for:

RF input Trace loss (p. 19 middle left graph)
TC4P1T transformer loss (p. 19 middle right graph) Output IP3 (dBm) RF Freq (Hz) -40 degC - 0 dBm - STD - 2.0E+8Hz IF-40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 100 degC - 0 dBm - STD - 2.0E+8Hz IF100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF Input P1dB (dBm) RF Freq (Hz) -40 degC - 0 dBm - STD - 2.0E+8Hz IF -40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF 25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 100 degC -0 dBm -STD -2.0E+8Hz IF 100 degC -0 dBm -LC (mod) -1.5E+8Hz IF Gain (dB) RF Freq (Hz) 25 degC - 6 dBm - STD - 2.0E+8Hz IF 25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF 25 degC -0 dBm -STD -2.0E+8Hz IF 25 degC -0 dBm -LC (mod) -1.5E+8Hz IF 25 degC - -3 dBm - STD - 2.0E+8Hz IF 25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF EVkit effects dePembedded, corrected for:
RF input Trace loss (p. 19 middle left graph)
TC4P1T transformer loss (p. 19 middle right graph) Output IP3 (dBm) RF Freq (Hz) 25 degC - 6 dBm - STD - 2.0E+8Hz IF25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC --3 dBm -STD -2.0E+8Hz IF 25 degC --3 dBm -LC (mod) -1.5E+8Hz IF Input P1dB (dBm) RF Freq (Hz) 25 degC - 6 dBm - STD - 2.0E+8Hz IF25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC --3 dBm -STD -2.0E+8Hz IF 25 degC --3 dBm -LC (mod) -1.5E+8Hz IF

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 16 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [High Side Injection see LC mode modifications on p. 25 ] (-11-) RF x 2LO vs. TCASE [IF = 154 MHz] ICC vs. TCASE LO to IF Leakage vs. TCASE RF x 2LO vs. LO Level [IF = 154 MHz] ICC vs. LO Level LO to IF Leakage vs. LO Level -100 -90 -80 -70 -60 -50 -40 -30 -20 -10

2 X 2 Rejection [Pin = -10 dBm] (dBc)

RF Freq (Hz) -40 degC - 5.00 V - 0 dBm - STD-40 degC - 5.00 V - 0 dBm - LC (mod) 25 degC -5.00 V -0 dBm -STD 25 degC -5.00 V -0 dBm -LC (mod) 100 degC -5.00 V -0 dBm -STD 100 degC -5.00 V -0 dBm -LC (mod) 0.200 0.220 0.240 0.260 0.280 0.300 0.320 0.340 0.360 0.380 0.400 ICC(Amps) RF Freq (Hz) -40 degC - 0 dBm - STD - 2.0E+8Hz IF-40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC -0 dBm -STD -2.0E+8Hz IF 25 degC -0 dBm -LC (mod) -1.5E+8Hz IF 100 degC - 0 dBm - STD - 2.0E+8Hz IF100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF -50 -45 -40 -35 -30 -25 -20 -15 -10 LO to IF Leakage (dBm) RF Freq (Hz) -40 degC - 0 dBm - STD - 2.0E+8Hz IF -40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF 25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 100 degC - 0 dBm - STD - 2.0E+8Hz IF 100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) 25 degC - 5.00 V - 6 dBm - STD 25 degC - 5.00 V - 6 dBm - LC (mod) 25 degC -5.00 V -0 dBm -STD 25 degC -5.00 V -0 dBm -LC (mod) 25 degC - 5.00 V - -3 dBm - STD25 degC - 5.00 V - -3 dBm - LC (mod) 0.200 0.220 0.240 0.260 0.280 0.300 0.320 0.340 0.360 0.380 0.400 ICC(Amps) RF Freq (Hz) 25 degC - 6 dBm - STD - 2.0E+8Hz IF25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - -3 dBm - STD - 2.0E+8Hz IF25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF -50 -45 -40 -35 -30 -25 -20 -15 -10 LO to IF Leakage (dBm) RF Freq (Hz) 25 degC - 6 dBm - STD - 2.0E+8Hz IF 25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF 25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - -3 dBm - STD - 2.0E+8Hz IF 25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 17 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [High Side Injection see LC mode modifications on p. 25 ] (-12-) R F to IF Leakage vs. TCASE 3RF x 3LO rejection vs. TCASE [IF = 154 MHz] R F to IF Leakage vs. LO Level 3RF x 3LO rejection vs. LO Level [IF = 154 MHz] -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 RF to IF Leakage [Pin = -10] (dBm) RF Freq (Hz) -40 degC - 0 dBm - STD - 2.0E+8Hz IF-40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF 25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 100 degC - 0 dBm - STD - 2.0E+8Hz IF100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) -40 degC -5.00 V -0 dBm -STD -40 degC -5.00 V -0 dBm -LC (mod) 25 degC - 5.00 V - 0 dBm - STD 25 degC - 5.00 V - 0 dBm - LC (mod) 100 degC - 5.00 V - 0 dBm - STD100 degC - 5.00 V - 0 dBm - LC (mod) -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 RF to IF Leakage [Pin = -10] (dBm) RF Freq (Hz) 25 degC - 6 dBm - STD - 2.0E+8Hz IF 25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - 0 dBm - STD - 2.0E+8Hz IF 25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF 25 degC - -3 dBm - STD - 2.0E+8Hz IF 25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 RF Freq (Hz) 25 degC -5.00 V -6 dBm -STD 25 degC -5.00 V -6 dBm -LC (mod) 25 degC -5.00 V -0 dBm -STD 25 degC -5.00 V -0 dBm -LC (mod) 25 degC -5.00 V --3 dBm -STD 25 degC -5.00 V --3 dBm -LC (mod)

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-DistortionTM Mixer 18 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [General] (-13-) E Vkit IF Port Match (TA = 25C) S ettling Time (STBY -> VIL) Main LO Port Match (TA = 25C, PMEAS = 0 dBm) Alt. LO port Match (TA = 25C, PMEAS = 0 dBm) Settling Time (STBY -> VIH) EVkit RF Port Match (TA = 25C) -30 -25 -20 -15 -10 50 100 150 200 250 300 350 400 450 500 550 IF Return Loss (dB) IF Frequency (MHz) Average of ChA STD Mode Average of ChA LC Mode Average of ChB STD Mode Average of ChB LC Mode -0.5 0.3 -0.1 0.1 0.3 0.5 -40 0 40 80 120 160 200 STBY Logic Pin (Volts) Vif Out (Volts) Time (nsec) Vif Vstby Turn On Settling Time: 150 nsec -30 -25 -20 -15 -10 LO port Return Loss (dB) LO Freq (GHz) STD Mode ON STD Mode STBY LC Mode ON LC Mode STBY For Main LO port connector (Pin 19) -30 -25 -20 -15 -10 Alt LO Port Return Loss (dB) LO Frequency (Hz) LC Mode: LO Power = 0 dBm Connector for Pin 27 -0.5 0.3 -0.1 0.1 0.3 0.5 -40 0 40 80 120 160 200 STBY Logic Pin (V) Vif Out (Volts) Time (nsec) Vif Vstby Turn Off Settling Time: 70 nsec -50 -45 -40 -35 -30 -25 -20 -15 -10 RF Port Return Loss (dB) RF Freq (GHz) Average of ChA STD Mode Average of ChA LC Mode Average of ChB STD Mode Average of ChB LC Mode LO = 2.2 GHz / 0 dBm

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-Distortion TM Mixer 19 Rev1, July 2012 DATASHEET TYPICAL O PERATING CONDITIONS [General] (-14-) I P3O vs. ∆∆ ∆∆f (TA = 25C, Freq = 2.6 GHz, IF = 200 MHz) EVkit Input RF Trace Loss (TA = 25C) IP3O Distribution (FIF = 200MHz, LC mode, N = 3340) I P3O vs. PIN (TA = 25C, Freq = 2.6 GHz, IF = 200 MHz) TC4-1T Transformer Loss Gain Distribution (FIF = 400MHz, STD mode, N = 3340) Output IP3 (dBm) Tone Separation (Hz) STD LC -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 2300 2400 2500 2600 2700 EVkit RF_A & RF_B Trace Loss (dB) RF Frequency (MHz) -40 degC 25 degC 100 degC See Noise Figure Plots. This is used to de-embed RAW EVkit measurements 10% 15% 20% 25% 30% 35% Percentage IP3O Bin (dBm) Channel B Channel A Output IP3 (dBm) Input Power (dBm/Tone) STD LC -1.4 -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0.0 TC4-1T Transformer Loss (dB) Frequency (Hz) -40C +25C +100C See Mixer Device Gain plots. This Data is used to de-embed the EVKit measured data 10% 15% 20% 25% 30% 35% Percentage Gain Bin (dB) Channel B Channel A

RF to IF Dual Downconverting Mixer IDT Zero-Distortion TM Mixer PACKAGE D RAWING (6X6 QFN) RF to IF Dual Downconverting Mixer 2300 - 2700 MHz

00 MHz F1162NBGI

Rev1, July 2012 DATASHEET

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-Distortion TM Mixer 21 Rev1, July 2012 DATASHEET PINOUTS 36 35 34 33 32 31 30 29 28 9RF_B 6NC [internal NC] 4NC [internal NC] 3GND [DB GND] 2GND [RFA_rtn] 1RF_A GND [DB GND] LO1_ADJ VCC 15NC [internal NC] IF_B- IF_B+ NC [internal NC] IF_BiasB VCC

19 LO_in

GND [internal NC]

21 VCC

GND [LCMODE ] GND [STBY] LO_SW [internal NC] GND [DB GND] LO_in_alt27 B I A S C T R L GND [DB GND] LO2_ADJ VCC NC [internal NC] IF_A- I F_A+ NC [internal NC] IF_BiasA VCC GND [DB GND] GND [DB GND] Black Text denotes recommended external connection Red Text denotes internal Function or Connection - DB GND = Downbonded to Paddle - Internal NC = Pin not connected GND [RFB_rtn] GND [LO_rtn] Please Note! - Only connect to one LO feed - Choose Either Pin 19 or Pin 27 - Do not connect the unused LO pin to ensure good LO return loss

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-Distortion TM Mixer 22 Rev1, July 2012 DATASHEET PIN D ESCRIPTIONS Pin Name Function 1 RF_A Main Channel RF Input. Internally matched to 50Ω. DO NOT apply DC to these pins 2, 8, 20 RF_Artn, RF_Brtn, LO_rtn Transformer Ground Returns. Ground these pins. 3, 5, 7, 18, 24, 28 GND Ground these pins. 4, 6, 12, 15, OK to connect to GND 10, 16, 21, 30, 36 VCC Power Supply. Bypass to GND with capacitors shown in the Typical Application Circuit as close as possible to pin. 9 RF_B Diversity Channel RF Input. Internally matched to 50Ω

11 IF_BiasB

Connect the specified resistor from this pin to ground to set the bias for the Diversity IF amplifier. This is NOT a current set resistor 13, 14 IFB+, IFB) Diversity Mixer Differential IF Output. Connect pullup inductors from each of these pins to VCC (see the Typical Application Circuit).

17 LO1_ADJ Connect the specified resistor for either Standard or LC mode

from this pin to ground to set the LO common buffer Icc 19, 27 LO_in LO_in_alt Local Oscillator Input. Connect the LO to this port through the recommended coupling capacitor. Note that you can only drive one LO port at a time. Remove the series capacitor f rom the unused port.

25 LC_MODE

Low_Current Mode. Set this pin to low or ground for LC mode. Set to high or No)Connect for Standard mode. There is an internal pull)up resistor. 22 STBY STBY Mode. Pull this pin high for Standby mode (~20 mA). Pull low or Ground for normal Operation

29 LO2_ADJ Connect the specified resistor for either Standard or LC mode

from this pin to ground to set the LO drive buffers Icc 32, 33 IFA), IFA+ Main Mixer Differential IF Output. Connect pullup inductors from each of these pins to VCC (see the Typical Application Circuit).

35 IF_BiasA Connect the specified resistor from this pin to ground to set the

bias for the Main IF amplifier. This is NOT a current set resistor — EP Exposed Pad. Internally connected to GND. Solder this exposed pad to a PCB pad that uses multiple ground vias to provide heat transfer out of the device into the PCB ground planes. These multiple via grounds are also required to achieve the noted RF performance.

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-Distortion TM Mixer 23 Rev1, July 2012 DATASHEET EVKIT SCHEMATIC 36 35 34 33 32 31 30 29 28 RF_B RF_B rtn NC 4NC GND RF_A rtn RF_A 18GND 17LO1_ADJ 16VCC 15NC 14IF_B- 13IF_B+ 12NC 11IF_BiasB 10VCC LO_in_alt27 LO_rtn B I A S C T R L C8J4 C10 C12 Vcc C13 R12 R11 C14 L3 L4 C15 Vcc R14 R13 C16 Vcc Vcc GND LO2_ADJ VCC NC IF_A- IF_A+ NC IF_BiasA VCC Vcc C6 R15 R16 L1 L2 C2 J2 Vcc R17 R18 Vcc 4:1 Balun 4:1 Balun C11 JP JP Vcc R9 R8 Vcc GND GND R10

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-Distortion TM Mixer 24 Rev1, July 2012 DATASHEET EVKIT PICTURE/LAYOUT/OPERATION Outer Position for STD Mode (R15, R17) Install Jumper for Mixer Operation Remove Jumper to Turn Mixer Off Close for LC Mode Open for STD Mode Inner Position for LC Mode (R16, R18) Outer Position for STD Mode (R11, R13) Inner Position for LC Mode (R12, R14) Alternate LO Port: Must remove C11 and Install C7 to use

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-Distortion TM Mixer 25 Rev1, July 2012 DATASHEET EVKIT BOM Default BOM: For Standard Mode, Open the LCMODE jumper in conjunction with positioning the 4 dual jumpers to select the resistors in red. F or Low Current Mode close the LCMODE jumper in conjunction with positioning the 4 dual jumpers to select the resistors in blue. M odified BOM (for High Side Injection LC Mode): EVkit Modifications for High Side Injection Low Current Mode (see TOCs on pages 15 – 17) Item # Value Size Desc Mfr. Part # Mfr. Part ReferenceQty 1 10nF 0402 CAP CER 10000PF 16V 10% X 7R 0402 GRM155R71C103KA01D MURATA C1,5,6,9,12,13,16 7 2 1000pF 0402 CAP CER 1000PF 50V C0G 0402 GRM1555C1H102JA01D MURATA C2,3,14,15 4 3 39pF 0402 CAP CER 39PF 50V 5% C0G 0402 GRM1555C1H390JZ010 MURATA C8,10 2 4 4.7pF 0402 CAP CER 4.7PF 50V 5% C0G 0402 GRM1555C1H4R7CZ01D MURATA C11 1 5 1pF 0402 Note: C7 and C11 cannot be installed together. C7 for Pin27 LO feed. C11 for Pin19 LO feedC7 1 6 10uF 0603 CAP CER 10UF 6.3V X 5R 0603 GRM188R60J106ME47D MURATA C4 1

7 Header 2 Pin TH 2 CONN HEADER VERT SGL 2POS GOLD 961102)6404)AR 3M JP1,2,3 3

8 Header 3 Pin TH 3 CONN HEADER VERT SGL 3POS GOLD 961103)6404)AR 3M JP4,5,6,7 4

9 SMA_END_LAUNCH .062 SMA_END_LAUNCH 142)0711)821 Emerson Johnson J1,2,3,4,5,6,7 7 10 270nH 0805 0805CS (2012) Ceramic Chip Inductor 0805CS)271X JLB COILCRAFT L1,2,3,4 4 11 40 0402 RES 40 OHM 1/10W 1% 0402 SMD ERJ)2RKF40R2X Panasonic R11,15 2 12 63 0402 RES 63 OHM 1/10W 1% 0402 SMD ERJ)2RKF62R0X Panasonic R12,16 2 13 91 0402 RES 91.0 OHM 1/10W 1% 0402 SMD ERJ)2RKF91R0X Panasonic R13 1 14 180 0402 RES 180 OHM 1/10W 1% 0402 SMD ERJ)2RKF1800X Panasonic R14 1 15 1.91k 0402 RES 1.91K OHM 1/10W 1% 0402 SMD ERJ)2RKF1911X Panasonic R18 1 16 1.21K 0402 RES 1.21K OHM 1/10W 1% 0402 SMD ERJ)2RKF1211X Panasonic R17 1 17 47K 0402 RES 47.0K OHM 1/16W 1% 0402 SMD RC0402FR)0747KL Yageo R8,9 2 18 0 0402 RES 0.0 OHM 1/10W 0402 SMD ERJ)2GE0R00X Panasonic R1,2,3,4,5,6,7,10 8 19 4:1 Balun SM)22 4:1 Center Tap Balun TC4)1TG2+ Mini Circuits T1,2 2

20 F1162 QFN)36 Div ersity Downconv erter F1162NBGI IDT U1 1

21 PCB F1162 EVKit Rev 5 1

Set these 3 Dual Jumpers as shown to INNER position and CLOSE LCMODE Jumper S et R14/R13 Jumper to OUTER position Will select 91 ohm resistor for pin17 instead of 180 ohm. All other resistors will be selected for Mode = Low Current Change C8 and C10 from 39 pF to 4.7 pF Change C11 from 4.7 pF to 3 pF

RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI IDT Zero-Distortion TM Mixer 26 Rev1, July 2012 DATASHEET TOPMARKINGS I DTF1162 NBGI YB1213A Q62A033M Part Number Date Code: [xxYYWWx] (Work Week 13 of 2012) Lot Code NOTE: Production Devices are DateCode 1213 or later.

TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com Contact Information For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit www.renesas.com /contact-us/ . Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD-PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers who are designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only to develop an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third-party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising from your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Disclaimer Rev.1.01) © 2025 Renesas Electronics Corporation. All rights reserved.

Product Information

F1162NBGI specifications and overview.

Summary

RF to IF Dual Downconverting Mixer Rev1, July 2012

Description

RF to IF Dual Downconverting Mixer Rev1, July 2012

Source title F1162NBGI Datasheet(PDF) - Renesas Technology Corp

Related Parts

More parts from the same family.

Browse manufacturer