F0562

Integrated Device Techn...

Sampling IF Receiver 2300MHz to 2700MHz

Manufacturer: Integrated Device Techn...

Document: 36 Pages / 2Mb

Request Quote Download Datasheet Read online HTML view

More from Integrated Device Techn... Browse F parts

Online Datasheet

Read F0562 online.

IDTF0562NLGI IDT | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 36

Technical content

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 1 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet GENERAL DESCRIPTION This document describes the specifications for the IDTF0562 2300MHz to 2700MHz dual path Sampling IF (SIF) Receiver used in Multi-mode, Multi-carrier BaseStation Receivers. Refer to the Part # Matrix below describing the frequency coverage of the complete series. This series is offered with high side or low side LO injection options for all UTRA bands and offers significantly better Noise and Distortion performance than currently available solutions. IF frequencies from 60MHz to 450MHz are supported. The IDTF0562 SIF provides 29dB gain and offers 47dB gain adjustment in 1dB steps designed to operate with a single 5V supply. Nominally, the device offers +44 dBm Output IP3 using 480mA of ICC. Alternately one can configure the device in low current (LC) mode to reduce power consumption to < 2 Watts. This device is packaged in a 10x10 68-pin Thin QFN with 50 ohm single-ended RF input and 200 ohm differential IF output impedances for ease of integration into the receiver lineup. The 200 ohm differential IF output can easily be matched to 100 ohms differential per the application drawing. COMPETITIVE ADVANTAGE IDT’s Zero-DistortionTM mixer in combination with interstage filtering and IDT’s proprietary FlatNoiseTM DVGA improves system SNR to the point where the external SAW filter can be eliminated. Both IP3O & NF are kept virtually flat while gain is backed off, enhancing SNR significantly under high level interferer conditions, and greatly benefiting 2G/3G/4G Multi-Carrier IF sampling receivers. In addition, total power consumption is reduced by 35% compared to conventional solutions.  No external SAW is needed  Reduced Power Consumption by 35%  NF and OIP3 virtually flat for first 13dB gain reduction The fast-settling, parallel mode gain step of 1.0dB coupled with the excellent differential non-linearity allow for SNR to be maximized further by targeting the minimum necessary gain in small, accurate increments. The matched output does not require a terminating resistor, thus the gain and distortion performance are preserved when driving Bandpass Anti-Alias filters.

FEATURES

 Dual Path for Diversity Systems  Combines FlatNoiseTM and Zero-Distortion technologies  29dB Total Power Gain  Ultra linear +44dBm IP3O  Low NF: 9.9dB @GMAX  50 Ω input impedance  Matched 100 Ω differential output impedance  Ultra high +19.8dBm P1dBo  Independent path standby mode  Constant LO impedance in STBY mode  47dB gain control range  6 bit parallel control  1dB Gain Steps  60MHz – 450MHz IF frequency range  Excellent 2nd Harmonic Rejection  ICC = 390mA LC Mode  10x10 68-pin TQFN package DEVICE BLOCK DIAGRAM PART# MATRIX Part# RF freq range UTRA bands IF freq range Typ. Gain Injection F0502 698 - 915 5,6,8,12,13,14,17 18,19,20 60 – 250 29 High Side F0552 1710 - 2050 1,2,3,4,9,10,23, 25,33,34,35,36, 37,39 60 – 450 29 Low & High Side F0562 2300 – 2700 7,38,40,41 60 – 450 29 Low & High Side RFIN_A RF VCO RFIN_B Bias Control Decode Logic IFOUT_A+ IFOUT_A- IFOUT_B+ IFOUT_B- GAIN_A[0:5] GAIN_B[0:5] TDD (STBY) LC_Mode Iset

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 2 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet Table of Contents

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 3 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet ABSOLUTE MAXIMUM RATINGS VCC to GND -0.3V to +5.5V A[5:0], B[5:0], TDD_A, TDD_B (STBY), LCMode -0.3V to (VCC + 0.25V) MX_IFA+, MX_IFA-, MX_IFB+, MX_IFB- -0.3V to (VCC + 0.25V) IFOUT_A+, IFOUT_A-, IFOUT_B+, IFOUT_B- 1V to (Vcc + 0.3V) LO1_ADJ +1V to +3V LO2_ADJ +2.1V to +4V MX_IF_BiasA, MX_IF_BiasB -0.3V to +0.3V LO_IN, RFIN_A, RFIN_B -0.3V to +0.3V RF Input Power (RFIN_A, RFIN_B) +20dBm ISET_A, ISET_B to GND -0.3V to +2.2V Continuous Power Dissipation 2.5W θJA (Junction – Ambient) +25°C/W θJC (Junction – Case) The Case is defined as the exposed paddle +3°C/W Operating Temperature Range (Case Temperature) TC = -40°C to +105°C Maximum Junction Temperature 150°C Storage Temperature Range -65°C to +150°C Lead Temperature (soldering, 10s) +260°C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 4 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet TRUTH TABLE – CHANNEL A & B Gain Set Target Gain CodeWord Code Name Gain Set Target Gain CodeWord Code Name Gain Set Target Gain CodeWord Code Name 27 000000 G27 5 010110 G5 -17 101100 G-17 26 000001 G26 4 010111 G4 -18 101101 G-18 25 000010 G25 3 011000 G3 -19 101110 G-19 24 000011 G24 2 011001 G2 -20 101111 G-20 23 000100 G23 1 011010 G1 -20 110000 G-20 22 000101 G22 0 011011 G0 -20 110001 G-20 21 000110 G21 -1 011100 G-1 -20 110010 G-20 20 000111 G20 -2 011101 G-2 -20 110011 G-20 19 001000 G19 -3 011110 G-3 -20 110100 G-20 18 001001 G18 -4 011111 G-4 -20 110101 G-20 17 001010 G17 -5 100000 G-5 -20 110110 G-20 16 001011 G16 -6 100001 G-6 -20 110111 G-20 15 001100 G15 -7 100010 G-7 -20 111000 G-20 14 001101 G14 -8 100011 G-8 -20 111001 G-20 13 001110 G13 -9 100100 G-9 -20 111010 G-20 12 001111 G12 -10 100101 G-10 -20 111011 G-20 11 010000 G11 -11 100110 G-11 -20 111100 G-20 10 010001 G10 -12 100111 G-12 -20 111101 G-20 9 010010 G9 -13 101000 G-13 -20 111110 G-20 8 010011 G8 -14 101001 G-14 -20 111111 G-20 7 010100 G7 -15 101010 G-15 6 010101 G6 -16 101011 G-16

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 5 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 RECOMMENDED OPERATING CONDITIONS Parameter Comment Symbol min typ max Units Supply Voltage(s) All VCC pins VCC 4.75 5.25 V LO Power PLO -3 +3 dBm Operating Temperature Range Case Temperature TCASE -40 +105 °C RF Freq Range FRF 2300 2700 MHz LO Freq Range FLO 1900 2800 IF Range FIF 60 450

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 6 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 SPECIFICATION IDTF0562 Typical Application Circuit, when operated as a Sampling IF Receiver, VCC = +5.00V, TC = +25°C, FRF = 2500MHz, FIF = 184MHz, FLO = 2316MHz, PLO = 0 dBm, Max gain output power = +3dBm per tone unless otherwise stated, TDD = LOW. EVkit IF transformer losses are de-embedded unless otherwise noted. Parameter Comment Symbol min typ max units Logic Input High For all control pins VIH 1.07 V Logic Input Low For all control pins VIL 0.68 V Logic Current For all control pins IIH, IIL -150 10 μA Supply Current Total VCC, STD Mode ISTD 480 540 mA Supply Current Total VCC, LC Mode ILC 390 435 mA Supply Current  Standby Mode  STBY = VIH  Total Both Channels ISTBY 27.5 37 mA Gain STD Mode Conversion Power Gain GSTDMAX 271 29 31 dB Gain LC Mode Conversion Power Gain GLC 26.9 28.9 30.9 dB Gain control range GRANGE 47 dB Gain STD mode min gain setting Maximum attenuation GSTDMIN -18 dB Step size GSTEP 1 dB Differential Gain Error Between any two adjacent 1dB steps DNL 0.1 0.22 dB Integral Gain Error Error vs. line (G27 Ref) INL 0.2 0.8 dB Phase Error Maximum phase change between GMAX and any state down to G-14 IPE 2.2 4 degree NF STD Mode Noise Figure (@ +25C) NFSTD 9.9 10.9 dB NF STD Mode 10dB reduced gain NFSTD_G-10 9.9 10.9 dB NF LC Mode Noise Figure (@ +25C) NFLC 9.6 10.6 dB NF LC Mode 10dB reduced gain NFLC_G-10 9.6 10.6 dB NF w/Blocker  +100 MHz offset blocker  PIN = +4 dBm  28dB gain reduced NFBLK 17.6 19 dB

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 7 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 SPECIFICATION (CONTINUED) IDTF0562 Typical Application Circuit, when operated as a Sampling IF Receiver, VCC = +5.00V, TC = +25°C, FRF = 2500MHz, FIF = 184MHz, FLO = 2316MHz, PLO = 0 dBm, Max gain output power = +3dBm per tone unless otherwise stated, TDD = LOW. EVkit IF transformer losses are de-embedded unless otherwise noted. Parameter Comment Symbol min typ max units Turn-on time  Gate STBY from VIH to VIL  Time for IF Signal to settle to within 0.1 dB of final value TSETTL 0.17 0.20 sec Attenuator adjustment settling time  Any two Adjacent 1dB Steps  +/-0.10 dB Pout settling T1dB 17.5 25 nsec Output IP3 Max Gain, STDMODE  Set GMAX,  800 KHz Tone Separation IP3O1 40 44 dBm Output IP3 10dB reduced gain, STDMODE  From GMAX to GMAX-10,  Pout = +1dBm per tone  800 KHz Tone Separation IP3O2 40 44 dBm Output IP3 10dB reduced gain, STDMODE  From GMAX to GMAX-10,  Pout = +1dBm per tone  800 KHz Tone Separation  -40C ≤ Tcase ≤ +105C  IF = 138MHz, LO = 2362MHz  IF = 184MHz, LO = 2316MHz  IF = 276MHz3, LO = 2224MHz IP3O3 43 dBm Output IP3 Max Gain, LCMODE  Set GMAX,  800 KHz Tone Separation IP3O4 40 44 dBm Input IP3 22dB reduced gain, STDMODE  Set GMAX-22dB,  Pin = -5dBm per tone  800 KHz Tone Separation IP3ISTD 26.5 31 dBm Input IP3 22dB reduced gain, LCMODE  Set GMAX-22dB,  Pin = -15dBm per tone  800 KHz Tone Separation IP3ILC 25 dBm 1 dB Compression Max Gain, STDMODE Output referred P1dBO1 17 19.8 dBm 1 dB Compression 30dB reduced gain, STDMODE  Input referred  Set GMAX-30dB P1dBI1 8.2 9.2 dBm 1 dB Compression Max Gain, LCMODE Output referred P1dBO2 17 19.8 dBm 1 dB Compression 30dB reduced gain, LCMODE  Input referred  Set GMAX-30dB P1dBI2 6.5 7 dBm 2RF – 2LO rejection Max Gain, STDMODE  Frequency = FRF - ½ FIF  PRF = -27dBm 2x21 -79 -69 dBc 2RF – 2LO rejection 17dB reduced gain, STDMODE  Frequency = FRF - ½ FIF  PRF = -10dBm 2x22 -67 -60 dBc

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 8 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 SPECIFICATION (CONTINUED) IDTF0562 Typical Application Circuit, when operated as a Sampling IF Receiver, VCC = +5.00V, TC = +25°C, FRF = 2500 MHz, FIF = 184MHz, FLO = 2316MHz, PLO = 0 dBm, Max gain output power = +3dBm per tone unless otherwise stated, TDD = LOW.) EVkit IF transformer losses are de-embedded unless otherwise noted. SPECIFICATION NOTES: 1 – Items in min/max columns in bold italics are Guaranteed by Test using BOM1 components supporting 4:1 output impedance transformation to 50 ohms 2 – All other Items in min/max columns are Guaranteed by Design Characterization using BOM2 components supporting 2:1 output impedance transformation to 100 ohms 3 – Matching network changed for 276MHz IF per BOM table values Parameter Comment Symbol min typ max units 2RF – 2LO rejection Max Gain, LCMODE  Frequency = FRF - ½ FIF  PRF = -27dBm 2x23 -76 -66 dBc 2RF – 2LO rejection 17dB reduced gain, LCMODE  Frequency = FRF - ½ FIF  PRF = -10dBm 2x24 -69 -60 dBc 2nd Harmonic Max Gain, STDMODE PRF = -27 dBm HD21 -80 -70 dBc 2nd Harmonic Max Gain, LCMODE PRF = -27 dBm HD23 -76 -66 dBc 3rd Harmonic Max Gain, STDMODE PRF = -27 dBm HD31 -93 -80 dBc 3rd Harmonic Max Gain, LCMODE PRF = -27 dBm HD33 -93 -80 dBc Channel Isolation Max Gain, STDMODE IF_B Pout vs. IF_A w/ RF_A input ISOC_STD 41 44.5 dB Channel Isolation Max Gain, LCMODE IF_B Pout vs. IF_A w/ RF_A input ISOC_LC 41 44.5 dB LO to IF leakage Max Gain, STDMODE ISOLI-1 -45 -39 dBm LO to IF leakage Max Gain, LCMODE ISOLI-3 -47 -40 dBm RF to IF leakage Max Gain, STDMODE PRF = -27 dBm ISORI-1 -83 -73 dBc RF to IF leakage Max Gain, LCMODE PRF = -27 dBm ISORI-2 -83 -73 dBc LO to RF leakage ISOLR -37 dBm RFIN Impedance Single Ended ZRFIN 50 Ω LO Port Impedance Single Ended ZLO 50 IF Output Impedance Differential ZIF 200

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 9 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TYPICAL OPERATING CONDITIONS (184 MHZ IF CENTER) Unless otherwise noted, the following conditions apply:  Applications circuit for 100ohm differential load with 184MHz +/- 40MHz BW into 2:1 Transformer. See schematic Below  Pout ~ +1dBm  Measurement on Channel A  PIN from -27dBm to -3dBm per Tone (Gain Setting Adjusted to yield Pout ~ +1dBm)  Tone Spacing = 800KHz  Device configured in Standard Mode with Low Side Injection  TCASE = 25C, VCC = 5.00V, LO Power = 0dBm  RF Frequency: 2.6GHz  IF Frequency: 184MHz  IF Transformer Losses are de-embedded  Input RF trace Losses are de-embedded Vcc C25/C13 = 3.0 pF L9/L12 = 30 nH L10/L11 = 30 nH C27/C12 = 20 pF C24/C9 = 20 pF L8/L4 = 150 nH L7/L3 = 150 nH 10 nF 10 nF 0.6 pF 100 ohm IFOUT- IFOUT+ Vcc 2:1 Transformer

184 MHz Output Match 200Ω to 100Ω

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 10 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, STD MODE, IF = 184MHZ] GAIN, OIP3, OIP2 (-1-) Gain vs. TCASE [low side inj.] Output IP3 vs. TCASE [low side inj.] Output IP2 vs. TCASE [low side inj.] Gain vs. TCASE [high side inj.] Output IP3 vs. TCASE [high side inj.] Output IP2 vs. TCASE [high side inj.] 144 184 224 144 184 224 144 184 224 144 184 224 144 184 224 -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B Gain (dB) RF Freq / IF Freq 144 184 224 144 184 224 144 184 224 144 184 224 144 184 224 -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B Output IP3 (dBm) RF Freq / IF Freq 100 144 184 224 144 184 224 144 184 224 144 184 224 144 184 224 -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B RF Freq / IF Freq Output IP2 (dBm) 184 184 184 184 184 -40degC / Channel A -40degC / Channel B 25degC / Channel A 25degC / Channel B 105degC / Channel A 105degC / Channel B Gain (dB) RF Freq / IF Freq 184 184 184 184 184 -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B Output IP3 (dBm) RF Freq / IF Freq 100 184 184 184 184 184 -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B RF Freq / IF Freq Output IP2 (dBm)

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 11 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [MAX GAIN, STD MODE, IF = 184MHZ] 2X2, L-I, DC CURRENT (-2-) 2 X 2 vs. TCASE [low side inj.] LO to IF Leakage [low side inj.] Total Current Drain [low side inj.] 2 x 2 vs. TCASE [high side inj.] LO to IF Leakage [high side inj.] Total Current Drain [high side inj.] -100 -90 -80 -70 -60 -50 -40 -30 -20 144 184 224 144 184 224 144 184 224 144 184 224 144 184 224 -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B 2X2 Rejection (dBc) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 144 184 224 144 184 224 144 184 224 144 184 224 144 184 224 -40 degC - Channel A -40 degC - Channel B 25 degC - Channel A 25 degC - Channel B 105 degC - Channel A 105 degC - Channel B LO to IF Leakage (dBm) RF Freq / IF Freq 0.42 0.44 0.46 0.48 0.50 0.52 144 184 224 144 184 224 144 184 224 144 184 224 144 184 224 -40 degC 25 degC 105 degC RF Freq / IF Freq Total ICC (Amps) RF Freq / IF Freq Total ICC (Amps) -100 -90 -80 -70 -60 -50 -40 -30 -20 184 184 184 184 184 -40 - Channel A -40 - Channel B 25 - Channel A 25 - Channel B 105 - Channel A 105 - Channel B 2X2 Rejection (dBc) RF Freq / IF Freq -65 -60 -55 -50 -45 -40 -35 -30 -25 184 184 184 184 184 -40 degC - Channel A -40 degC - Channel B 25 degC - Channel A 25 degC - Channel B 105 degC - Channel A 105 degC - Channel B LO to IF Leakage (dBm) RF Freq / IF Freq 0.42 0.44 0.46 0.48 0.50 0.52 184 184 184 184 184 -40 degC 25 degC 105 degC RF Freq / IF Freq Total ICC (Amps) RF Freq / IF Freq Total ICC (Amps)

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 12 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [SWEPT GAIN, STD MODE, IF = 184MHZ, LS INJECTION] GAIN, OIP3, IIP3 (-3-) Gain [2.4 GHz] Output IP3 [2.4 GHz] Input IP3 [2.4 GHz] Gain [2.6 GHz] Output IP3 [2.6 GHz] Input IP3 [2.6 GHz] 3579111315171921232527 Gain (dB) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB 3579111315171921232527 Output IP3 (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB 3579111315171921232527 Input IP3 (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB 3579111315171921232527 Gain (dB) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB 3579111315171921232527 Output IP3 (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB 3579111315171921232527 Input IP3 (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 13 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [SWEPT GAIN, STD MODE, IF = 184MHZ, LS INJECTION] OIP2, IIP2, 2X2 (-4-) Output IP2 [2.4 GHz] Input IP2 [2.4 GHz] 2x2 Rejection [2.4 GHz] Output IP2 [2.6 GHz] Input IP2 [2.6 GHz] 2x2 Rejection [2.6 GHz] 3579111315171921232527 Output IP2 (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB 3579111315171921232527 Input IP2 (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -90 -80 -70 -60 -50 -40 -30 -20 3579111315171921232527

2 X 2 Rejection (dBc)

Gain Setting (dB) / Pin (dBm) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB 3579111315171921232527 Output IP2 (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB 3579111315171921232527 Input IP2 (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -90 -80 -70 -60 -50 -40 -30 -20 3579111315171921232527 Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 14 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [SWEPT GAIN, STD MODE, IF = 184MHZ, LS INJECTION] 3X3, L-I, R-I (-5-) 3x3 Rejection [2.4 GHz] LO to IF Leakage [low side inj, 2.6 GHz] RF to IF Leakage [2.4 GHz] 3x3 Rejection [2.6 GHz] LO to IF Leakage [high side inj., 2.6 GHz] RF to IF Leakage [2.6 GHz] -100 -90 -80 -70 -60 -50 -40 -30 -20 3579111315171921232527

3 X 3 Rejection (dBc)

Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -75 -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 3579111315171921232527 LO to IF Leakage (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -95 -90 -85 -80 -75 -70 -65 -60 -55 -50 -45 -40 3579111315171921232527 RF to IF Leakage (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -90 -80 -70 -60 -50 -40 -30 -20 3579111315171921232527 Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -75 -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 3579111315171921232527 LO to IF Leakage (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB -100 -95 -90 -85 -80 -75 -70 -65 -60 -55 -50 -45 -40 3579111315171921232527 RF to IF Leakage (dBm) Gain Setting (dB) / PIN (dBm/Tone) -40C / ChA -40C / ChB +25C / ChA +25C / ChB +105C / ChA +105C / ChB

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 15 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [SWEPT GAIN, LC MODE, IF = 184MHZ, LS INJECTION] GAIN, OIP3, IIP3 (-6-) Gain [v Temp] Output IP3 [v Temp] Input IP3 [v Temp] Gain [v LO Power] Output IP3 [v LO Power] Input IP3 [v LO Power] 46810121416182022242628 Gain (dB) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B 46810121416182022242628 Output IP3 (dBm) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B 46810121416182022242628 Input IP3 (dBm) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B 46810121416182022242628 Gain (dB) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B 46810121416182022242628 Output IP3 (dBm) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B 46810121416182022242628 Input IP3 (dBm) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 16 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [SWEPT GAIN, LC MODE, IF = 184MHZ, LS INJECTION] OIP2, CHAN ISO, 2X2 (-7-) Output IP2 [v Temp] Channel Isolation [v Temp] 2x2 Rejection [v Temp] Output IP2 [v LO Power] Channel Isolation [v LO Power] 2x2 Rejection [v LO Power] 46810121416182022242628 Output IP2 (dBm) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B 46810121416182022242628 Channel Isolation (dB) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 46810121416182022242628 2x2 Rejection (dBc) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B 46810121416182022242628 Output IP2 (dBm) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B 46810121416182022242628 Channel Isolation (dB) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 46810121416182022242628 2x2 Rejection (dBc) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 17 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [SWEPT GAIN, LC MODE, IF = 184MHZ, LS INJECTION] 3X3, L-I, DC CURRENT, R-I (-8-) 3x3 Rejection [v Temp] LO to IF Leakage [v Temp] RF to IF Leakage [v Temp] 3x3 Rejection [v LO Power] Total ICC [v Temp] RF to IF Leakage [v LO Power] -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 46810121416182022242628 3x3 Rejection (dBc) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 46810121416182022242628 LO to IF Leakage (dBm) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B -90 -80 -70 -60 -50 -40 -30 -20 -10 46810121416182022242628 RF to IF Leakage (dBc) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 46810121416182022242628 3x3 Rejection (dBc) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B 240 280 320 360 400 440 480 46810121416182022242628 Total ICC (mA) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B -90 -80 -70 -60 -50 -40 -30 -20 -10 46810121416182022242628 RF to IF Leakage (dBc) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 18 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TYPICAL OPERATING CONDITIONS [276 MHZ IF CENTER] Unless otherwise noted, the following conditions apply:  Applications circuit for 100ohm differential load with 276MHz +/- 40 MHzBW into 2:1 Transformer. See schematic Below  Pout ~ +1dBm (for Gain Setting > 5dB)  Measurement on Channel A  PIN from -27dBm to -6dBm per Tone (Gain Setting Adjusted to yield Pout ~ +1dBm)  Tone Spacing = 800KHz  Device configured in Standard Mode with Low Side Injection  TCASE = 25C, VCC = 5.00V, LO Power = 0dBm  RF Frequency: 2.4GHz, 2.6GHz  IF Frequency: 276MHz  IF Transformer Losses are de-embedded  Input RF trace Losses are de-embedded Vcc C25/C13 = 1.2 pF L9/L12 = 24 nH L10/L11 = 24 nH C27/C12 = 8 pF C24/C9 = 8 pF L8/L4 = 82 nH L7/L3 =82 nH 10 nF 10 nF 0.6 pF 100 ohm IFOUT- IFOUT+ Vcc 2:1 Transformer

276 MHz Output Match 200 Ω to 100Ω

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 19 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [SWEPT GAIN, STD MODE, IF = 276MHZ, LS INJECTION] GAIN, OIP3, OIP2 (-9-) Gain [2.4 GHz] Output IP3 [2.4 GHz] Output IP2 [2.4 GHz] Gain [2.6 GHz] Output IP3 [2.6 GHz] Output IP2 [2.6 GHz] -22 -18 -14 -10 -20-16-12-8-40481216202428 Gain (dB) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.4GHz / Ch A 25degC / 3dBm / 2.4GHz / Ch B 25degC / 0dBm / 2.4GHz / Ch A 25degC / 0dBm / 2.4GHz / Ch B 25degC / -3dBm / 2.4GHz / Ch A 25degC / -3dBm / 2.4GHz / Ch B -20-16-12-8-40481216202428 Output IP3 (dBm) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.4GHz / Ch A 25degC / 3dBm / 2.4GHz / Ch B 25degC / 0dBm / 2.4GHz / Ch A 25degC / 0dBm / 2.4GHz / Ch B 25degC / -3dBm / 2.4GHz / Ch A 25degC / -3dBm / 2.4GHz / Ch B 100 110 -20-16-12-8-40481216202428 Output IP2 (dBm) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.4GHz / Ch A 25degC / 3dBm / 2.4GHz / Ch B 25degC / 0dBm / 2.4GHz / Ch A 25degC / 0dBm / 2.4GHz / Ch B 25degC / -3dBm / 2.4GHz / Ch A 25degC / -3dBm / 2.4GHz / Ch B -22 -18 -14 -10 -20-16-12-8-40481216202428 Gain (dB) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B -20-16-12-8-40481216202428 Output IP3 (dBm) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B 100 110 -20-16-12-8-40481216202428 Output IP2 (dBm) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 20 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS [SWEPT GAIN, STD MODE, IF = 276MHZ, LS INJECTION] 2X2, 3X3, CURRENT, R-I, ISO (-10-) 2x2 Rejection [2.4 GHz] 3x3 Rejection [2.6 GHz] RF to IF Leakage [2.6 GHz] 2x2 Rejection [2.6 GHz] Total ICC [2.6 GHz] Channel Isolation [2.6 GHz] -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 -20-16-12-8-40481216202428 2 x 2 Rejection (dBc) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.4GHz / Ch A 25degC / 3dBm / 2.4GHz / Ch B 25degC / 0dBm / 2.4GHz / Ch A 25degC / 0dBm / 2.4GHz / Ch B 25degC / -3dBm / 2.4GHz / Ch A 25degC / -3dBm / 2.4GHz / Ch B -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 -20-16-12-8-40481216202428 3 x 3 Rejection (dBc) Gain Setting (dB) / Pin (dBm) 25degC / 3dBm / 2.6GHz / Ch A 25degC / 3dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 25degC / -3dBm / 2.6GHz / Ch A 25degC / -3dBm / 2.6GHz / Ch B -90 -80 -70 -60 -50 -40 -30 -20 -10 -20-16-12-8-40481216202428 RF to IF Leakage (dBc) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 -20-16-12-8-40481216202428 2 x 2 Rejection (dBc) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B 320 360 400 440 480 520 560 -20-16-12-8-40481216202428 Total ICC (mA) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch A -20-16-12-8-40481216202428 Channel Isolation (dB) Gain Setting (dB) / Pin (dBm) -40degC / 0dBm / 2.6GHz / Ch A -40degC / 0dBm / 2.6GHz / Ch B 25degC / 0dBm / 2.6GHz / Ch A 25degC / 0dBm / 2.6GHz / Ch B 105degC / 0dBm / 2.6GHz / Ch A 105degC / 0dBm / 2.6GHz / Ch B

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 21 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS RETURN LOSS [STD MODE] (-11-) IF_A Output Return Loss 184MHz match IF_A Output Return Loss 276MHz match RF Port Return Loss IF_B Output Return Loss 184MHz match IF_B Output Return Loss 276MHz match LO Port Return Loss -35 -30 -25 -20 -15 -10 84 104 124 144 164 184 204 224 244 264 284 Return Loss (dB) IF Frequency (MHz) G-20 G10 G15 G17 G20 G23 G25 G27 -35 -30 -25 -20 -15 -10 176 196 216 236 256 276 296 316 336 356 376 Return Loss (dB) IF Frequency (MHz) G-20 G10 G15 G17 G20 G23 G25 G27 -30 -25 -20 -15 -10 Return Loss (dB) RF Frequency (GHz) ChA / LO=2.2GHz ChA / LO=2.6GHz ChB / LO=2.2GHz ChB / LO=2.6GHz -35 -30 -25 -20 -15 -10 84 104 124 144 164 184 204 224 244 264 284 Return Loss (dB) IF Frequency (MHz) G-20 G10 G15 G17 G20 G23 G25 G27 -35 -30 -25 -20 -15 -10 176 196 216 236 256 276 296 316 336 356 376 Return Loss (dB) IF Frequency (MHz) G-20 G10 G15 G17 G20 G23 G25 G27 -30 -25 -20 -15 -10 Return Loss (dB) LO Frequency (GHz) LO

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 22 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS NOISE FIGURE, GAIN ACCURACY, P1dB [STD MODE] (-12-) NF v Gain [RF=2.6G, IF=184M, ChA, LS Injection] Gain Accuracy [RF =2.6G, IF=184M, LS Injection] Input P1dB [IF =184 MHz, Low Side Injection] NF v RF/IF Frequency [ChA, LS Injection] Output P1dB [IF = 184 MHz, Low Side Injection] Input P1dB [IF = 184 MHz, Low Side Injection] -20-16-12-8-40481216202428 Noise Figure (dB) Gain Setting (dB) -40 degC 25 degC 105 degC -1.0 -0.6 -0.2 0.2 0.6 1.0 -24-20-16-12-8-40481216202428 Absolute Gain Accuracy (dB) Gain Setting (dB) -40C_CHA -40C_CHB 25C_CHA 25C_CHB 105C_CHA 105C_CHB -10 Input P1dB (dBm) RF Frequency (GHz) 27dB Gain Setting / Channel A 27dB Gain Setting / Channel B 17dB Gain Setting / Channel A 17dB Gain Setting / Channel B 7dB Gain Setting / Channel A 7dB Gain Setting / Channel B 144M 184M 224M 144M 184M 224M 2400MHz 2600MHz -40degC / 27dB GainSet -40degC / 17dB GainSet 25degC / 27dB GainSet 25degC / 17dB GainSet 105degC / 27dB GainSet 105degC / 17dB GainSet Noise Figure (dB) RF Freq / IF Freq Output P1dB (dBm) RF Frequency (GHz) 27dB Gain Setting / Channel A 27dB Gain Setting / Channel B 17dB Gain Setting / Channel A 17dB Gain Setting / Channel B 7dB Gain Setting / Channel A 7dB Gain Setting / Channel B -10 -20-16-12-8-40481216202428 Input P1dB (dBm) Gain Setting (dB) -40 degC 25 degC 105 degC

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 23 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS M X N SPURS [IF = 276 MHZ, LO = 2.2586 GHZ, TCASE = 25C] (-13-) Spur Rejection [ChA, Spur PIN = -5 dBm] Spur Rejection [ChA, Spur PIN = 0 dBm] Transformer TC2-7T Loss vs. Temperature Spur Rejection [ChB, Spur PIN = -5 dBm] Spur Rejection [ChB, Spur PIN = 0 dBm] -3 3 -2 2 -3 3 -1 -2-3 32 1 -2 2 -1 1 -1 1 1 -1 1 -1 2 -2 1 23 -3-2 -1 3 -3 2 -2 3 -3 -1000 1000 3000 5000 7000 9000 11000 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 Spur Rejection (dBc) Spur Frequency (GHz) Spur Rejection (dBc) M x RF N x LO FundamentalImage -3 3 -2 2 -3 3 -1 -2-3 32 1 -2 2 -1 1 -1 1 1 -1 1 -1 2 -2 1 23 -3-2 -1 3 -3 2 -2 3 -3 -1000 1000 3000 5000 7000 9000 11000 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 Spur Rejection (dBc) Spur Frequency (GHz) Spur Rejection (dBc) M x RF N x LO FundamentalImage Sig Gen Out of Range 0.00 0.25 0.50 0.75 1.00 1.25 1.50 -40 25 100 IF Frequency (GHz) TC2 Loss (dB) -3 3 -2 2 -3 3 -1 -2-3 32 1 -2 2 -1 1 -1 1 1 -1 1 -1 2 -2 1 23 -3-2 -1 3 -3 2 -2 3 -3 -1000 1000 3000 5000 7000 9000 11000 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 Spur Rejection (dBc) Spur Frequency (GHz) Spur Rejection (dBc) M x RF N x LO FundamentalImage -3 3 -2 2 -3 3 -1 -2-3 32 1 -2 2 -1 1 -1 1 1 -1 1 -1 2 -2 1 23 -3-2 -1 3 -3 2 -2 3 -3 -1000 1000 3000 5000 7000 9000 11000 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 Spur Rejection (dBc) Spur Frequency (GHz) Spur Rejection (dBc) M x RF N x LO FundamentalImage Sig Gen Out of Range

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 24 Rev1, April 2014 IDTF0562NBGI Datasheet F0552NBGI Advance Datasheet TOCS HISTOGRAMS [N= 4584, TCASE = 25C] (-14-) Gain [RF = 2500M, LO = 2316M, GMAX] Output IP3 [RF = 2500M, LO = 2316M, G17] ATTN Accuracy2 [RF = 2500M, LO = 2316, ChA] Output IP3 [RF = 2500M, LO = 2316M, GMAX] ATTN Accuracy1 [RF = 2500M, LO = 2316, ChA] Total ICC [LO = 2316M, VCC = 5.00 V] 10% 15% 20% 25% 30% 35% 40% Percent Gain Bin (dB) ChA ChB 10% 15% 20% 25% Percent Output IP3 Bin (dBm) ChA ChB Gain Setting = 17 dB (10 dB Reduced from Max Gain) 10% 15% 20% 25% 30% Percent Attenuation Accuracy Bin (dB) 32 dB 47 dB 10% 15% 20% 25% Percent Output IP3 Bin (dBm) ChA ChB 10% 20% 30% 40% 50% 60% 70% Percent Attenuation Accuracy Bin (dB) 8 dB 16 dB 10% 15% 20% 25% 30% 35% Percent Total Current Draw Bin (mA) STD mode LC mode

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 25 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet PACKAGE DRAWING (10X10 68-PIN THIN QFN)

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 26 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 PINOUT: IDTF0552/0502/0562NLGI 68B5 NC VCC ISET_B GND IFOUT_B+ IFOUT_B- NC NC NC MX_IF_BiasB NC MX_IFB+ MX_IFB- GND VCC GND VCC LO1_Adj GND GND LO_IN LO_IN_RTN VCC LO2_Adj GND NC MX_IFA- MX_IFA+ NC MX_IF_BiasA NC NC GND IFOUT_A- IFOUT_A+ GND ISET_A VCC NC VCC GND VCC GND RFIN_A GND NC TDD_A LCmode TDD_B NC GND RFIN_B GND VCC GND VCC

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 27 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 PIN DESCRIPTION TABLE Pin Name Function 1, 3, 15, 17, 25, 38, 40, 46, VCC Power Supply. Bypass to GND with capacitors shown in the Typical Application Circuit as close as possible to pin. 2, 4, 6, 12, 14, 16, 27, 37, 39, 42, 43, 48, 56, GND Ground these pins. 5 RFIN_A Main Channel RF Input. Internally matched to 50Ω. DO NOT apply DC to these pins 7, 11, 24, 30, 31, 32, 34, 49, 52, 54, 55, 62 NC No Connection. Not internally connected. OK to connect to VCC, OK to connect to GND

8 TDD_A

Standby control for Channel A. Includes an internal pull-up resistor so leave as NC for Standby mode. Set this pin to low or GND for normal operation. 9 LCmode Low_Current Mode. Includes an internal pull-up resistor so leave as NC for LC mode. Set this pin to low or GND for STD mode.

10 TDD_B

Standby control for Channel B. Includes an internal pull-up resistor so leave as NC for Standby mode. Set this pin to low or GND for normal operation. 13 RFIN_B Diversity Channel RF Input. Internally matched to 50Ω

18 B5 Parallel Gain Control Input - MSB

19 B4 Parallel Gain Control Input

20 B3 Parallel Gain Control Input

21 B2 Parallel Gain Control Input

22 B1 Parallel Gain Control Input

23 B0 Parallel Gain Control Input – LSB (1 dB step)

26 ISET_B ChB VGA Icc set: Recommended resistor value = 3.83K 28 IFOUT_B+ Channel B Differential Output +. Pull up to Vcc through an inductor 29 IFOUT_B- Channel B Differential Output -. Pull up to Vcc through an inductor

33 MX_IF_BiasB

Connect the specified resistor for either Standard mode (41ohm) or LC mode (62ohm) from this pin to ground to set the bias for the Diversity IF amplifier. This is NOT a current set resistor. 35 MX_IFB+ Diversity Mixer Differential IF (+) Output. Connect a pullup inductor from this pin to VCC. 36 MX_IFB- Diversity Mixer Differential IF (-) Output. Connect a pullup inductor from this pin to VCC.

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 28 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 PIN DESCRIPTION TABLE (CONTINUED)

41 LO1_ADJ

Connect the specified resistor for either Standard mode (220ohm) or LC mode (240ohm) from this pin to ground to set the LO common buffer Icc. 44 LO_IN Local Oscillator Input. Connect the LO to this port through the recommended coupling capacitor. 45 LO_IN_RTN Transformer ground return. Ground this pin.

47 LO2_ADJ

Connect the specified resistor for either Standard mode (1.3K) or LC mode (2.15K) from this pin to ground to set the LO drive buffers Icc. 50 MX_IFA- Diversity Mixer Differential IF (-) Output. Connect a pullup inductor from this pin to VCC. 51 MX_IFA+ Diversity Mixer Differential IF (+) Output. Connect a pullup inductor from this pin to VCC.

53 MX_IF_BiasA

Connect the specified resistor for either Standard mode (41ohm) or LC mode (62ohm) from this pin to ground to set the bias for the Diversity IF amplifier. This is NOT a current set resistor. 57 IFOUT_A- Channel A Differential Output -. Pull up to Vcc through an inductor 58 IFOUT_A+ Channel A Differential Output +. Pull up to Vcc through an inductor 60 ISET_A ChA VGA Icc set: Recommended resistor value = 3.83K

63 A0 Parallel Gain Control Input – LSB (1dB step)

64 A1 Parallel Gain Control Input

65 A2 Parallel Gain Control Input

66 A3 Parallel Gain Control Input

67 A4 Parallel Gain Control Input

68 A5 Parallel Gain Control Input - MSB

— EP Exposed Pad. Internally connected to GND. Solder this exposed pad to a PCB pad that uses multiple ground vias to provide heat transfer out of the device into the PCB ground planes. These multiple via grounds are also required to achieve the noted RF performance.

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 29 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 DIGITAL PIN VOLTAGE & RESISTANCE VALUES The following table provides open-circuit DC voltage and resistance values referenced to ground for each of the control pins listed. Pin Name DC voltage (volts) Resistance (ohms)

8 TDD_A 5 50k

9 LC_MODE 5 50k

10 TDD_B 5 50k

18 – 23 B0-B5 5 50k 63 - 68 A0-A5 5 50k

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 30 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet APPLICATIONS INFORMATION Power Supplies A common VCC power supply should be used for all pins requiring DC power. All supply pins should be bypassed with external capacitors to minimize noise and fast transients. Supply noise can degrade noise figure and fast transients can trigger ESD clamps and cause them to fail. Supply voltage change or transients should have a slew rate smaller than 1V/20uS. In addition, all control pins should remain at 0V (+/-0.3V) while the supply voltage ramps or while it returns to zero. Control Pin Interface If control signal integrity is a concern and clean signals cannot be guaranteed due to overshoot, undershoot, ringing, etc., provisions for an R-C circuit at the input of each control and data pin is recommended. This applies to pins 8, 9, 10, 18 - 23, and 63 - 68 as shown below. IDTF0552/0502/0562NLGI B3 B2 TDD_A LCmode TDD_B 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf 5Kohm 2pf

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 31 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet EVKIT & TYPICAL APPLICATION SCHEMATIC: The following schematic describes the recommended EVkit and applications circuit.

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 32 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet SCHEMATIC CONTINUED FROM PREVIOUS PAGE

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 33 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet EVKIT PICTURE LEAVE OPEN FOR LC MODE, SHORT FOR STD MODE INSTALL JUMPER IN OUTER POSITION FOR CHANNEL A STD MODE INNER POSITION FOR CHANNEL A LC MODE SHORT FOR CHANNEL A NORMAL OPERATION LEAVE OPEN CHANNEL A STBY MODE SHORT FOR CHANNEL B NORMAL OPERATION LEAVE OPEN CHANNEL B STBY MODE INSTALL JUMPER IN OUTER POSITION FOR STD MODE INNER POSITION FOR LC MODE INSTALL JUMPER IN OUTER POSITION FOR CHANNEL B STD MODE INNER POSITION FOR CHANNEL B LC MODE

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 34 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet IDTF0562 BOM 1 & 2 Two BOMs are included: BOM1 supports the 4:1 output transformation from 200ohms to 50ohms used for production test and BOM2 supports the 2:1 output transformation from 200ohms to 100ohms used to generate the typical operating curve graphs. BOM1 includes components for 4:1 output transformation supporting production test (IF center frequency 184MHz) BOM2 includes components for 2:1 output transformation used for TOCs (IF center frequency 184MHz +/ - 40MHz) F0562 BOM 4:1 IF=184Mhz Item # Value Size/RevDesc Mfr. Part # Mfr. Supplier Part # Supplier Part Reference Qty 1 39pF 0402 CAP CER 39PF 50V 5% C0G 0402 GRM1555C1H390JZ010MURATA 490-1286-1-ND Digikey C3,4,19 3 2 10nF 0402 CAP CER 10000PF 16V 10% X7R 0402 GRM155R71C103KA01DMURATA 490-1313-1-ND Digikey C1,2,5,6,7,10,11,14,15, 17, 21,22,26,28,29,30 16 3 1000pF 0402 CAP CER 1000PF 50V C0G 0402 GRM1555C1H102JA01DMURATA 490-3244-1-ND Digikey C9,12,24,27 4 4 0.6pF 0402 CAP CER 0.6pF 50V C0G +/-0.1pF 0402GJM1555C1HR60BB01DMURATA 81-GJM1555C1HR60BB01DMouser C8,32 2 5 10uF 0603 CAP CER 10UF 6.3V X5R 0603 GRM188R60J106ME47DMURATA 490-3896-1-ND Digikey C31 1 6 91 0402 RES 91.0 OHM 1/10W 1% 0402 SMD ERJ-2RKF91R0X Panasonic P91.0LCT-ND Digikey R15 1 7 180 0402 RES 180 OHM 1/10W 1% 0402 SMD ERJ-2RKF1800X Panasonic P180LCT-ND Digikey R16 1 8 100 0402 RES 100 OHM 1/10W 1% 0402 SMD ERJ-2RKF1000X Panasonic P100LCT-ND Digikey R22, 23 2 9 1.21K 0402 RES 1.21K OHM 1/10W 1% 0402 SMD ERJ-2RKF1211X Panasonic P1.21KLCT-ND Digikey R18 1 10 1.91k 0402 RES 1.91K OHM 1/10W 1% 0402 SMD ERJ-2RKF1911X Panasonic P1.91KLCT-ND Digikey R19 1 11 110 0402 RES 110 OHM 1/10W 1% 0402 SMD ERJ-2RKF1100X Panasonic P110LCT-ND Digikey R10,21 2 12 3.48K 0402 RES 3.48K OHM 1/10W 1% 0402 SMD ERJ-2RKF3481X Panasonic P3.48KLCT-ND Digikey R9,24 2 13 40.2 0402 RES 40.2 OHM 1/10W 1% 0402 SMD ERJ-2RKF40R2X Panasonic P40.2LCT-ND Digikey R11,20 2 14 0 0402 RES 0.0 OHM 1/10W 0402 SMD ERJ-2GE0R00X Panasonic P0.0JCT-ND Digikey R1,2,12,13,14,17,25,L9- 11 15 SMA_END_LAUNCH .062 SMA_END_LAUNCH (Big) 142-0701-851 Emerson Johnson530-142-0701-851 Mouser J1,5,9 3 16 SMA_END_LAUNCH .062 SMA_END_LAUNCH (small) 142-0711-821 Emerson Johnson530-142-0711-821 Mouser J6,12,14 3

17 Header 14 Pin TH 14 CONN HEADER VERT SGL 14POS GOLDN2514-6002-RB 3M MHC14K-ND Digikey J15 1

18 Header 2 Pin TH 2 CONN HEADER VERT SGL 2POS GOLD 961102-6404-AR 3M 3M9447-ND Digikey J2,3,4,13 4

19 Header 3 Pin TH 3 CONN HEADER VERT SGL 3POS GOLD 961103-6404-AR 3M 3M9448-ND Digikey J7,8,10,11 4

20 1:4 Balun SM-22 4:1 Center Tap Balun TC4-1WG2+ Mini Circuits TC4-1WG2+ Mini Circuits T1,2 2 21 390 nH 0805 0805CS (2012) Ceramic Chip Inductor 0805CS-391XJLB COILCRAFT 0805CS-391XJLB COILCRAFTL1-L8 8

22 F0562 TQFN-68Sampling IF receiver F0562 IDT F0562 IDT U1 1

23 PCB 04 Printed Circuit Board F0552 EV Kit Rev 04 CC 1

24 DNP Do Not Populate C13,25

25 BOM 01 Bill Of Material

F0562 BOM 2:1 IF=184Mhz Item # Value Size/Rev Desc Mfr. Part # Mfr. Supplier Part # Supplier Part Reference Qty 1 39pF 0402 CAP CER 39PF 50V 5% C0G 0402 GRM1555C1H390JZ010MURATA 490-1286-1-ND Digikey C3,4,19 3 2 10nF 0402 CAP CER 10000PF 16V 10% X7R 0402 GRM155R71C103KA01DMURATA 490-1313-1-ND Digikey C1,2,5,6,7,10,11,14, 15,17, 16 3 20pF 0402 CAP CER 20pF 50V C0G 0402 GRM1555C1H200JZ01DMURATA 490-1282-1-ND Digikey C9,12,24,27 4 4 3pF 0402 CAP CER 3pF 50V C0G 0402 GRM1555C1H3R0CZ01DMURATA 490-3205-1-ND Digikey C13,25 2 5 0.6pF 0402 CAP CER 0.6pF 50V C0G +/-0.1pF GJM1555C1HR60BB01DMURATA 81-GJM1555C1HR60BB01DMouser C8, 32 2 6 10uF 0603 CAP CER 10UF 6.3V X5R 0603 GRM188R60J106ME47DMURATA 490-3896-1-ND Digikey C31 1 7 91 0402 RES 91.0 OHM 1/10W 1% 0402 SMD ERJ-2RKF91R0X Panasonic P91.0LCT-ND Digikey R15 1 8 180 0402 RES 180 OHM 1/10W 1% 0402 SMD ERJ-2RKF1800X Panasonic P180LCT-ND Digikey R16 1 9 100 0402 RES 100 OHM 1/10W 1% 0402 SMD ERJ-2RKF1000X Panasonic P100LCT-ND Digikey R22, 23 2 10 1.21K 0402 RES 1.21K OHM 1/10W 1% 0402 SMD ERJ-2RKF1211X Panasonic P1.21KLCT-ND Digikey R18 1 11 1.91k 0402 RES 1.91K OHM 1/10W 1% 0402 SMD ERJ-2RKF1911X Panasonic P1.91KLCT-ND Digikey R19 1 12 110 0402 RES 110 OHM 1/10W 1% 0402 SMD ERJ-2RKF1100X Panasonic P110LCT-ND Digikey R10,21 2 13 3.48K 0402 RES 3.48K OHM 1/10W 1% 0402 SMD ERJ-2RKF3481X Panasonic P3.48KLCT-ND Digikey R9,24 2 14 40.2 0402 RES 40.2 OHM 1/10W 1% 0402 SMD ERJ-2RKF40R2X Panasonic P40.2LCT-ND Digikey R11,20 2 15 0 0402 RES 0.0 OHM 1/10W 0402 SMD ERJ-2GE0R00X Panasonic P0.0JCT-ND Digikey R1,2,12,13,14,17,25 7 16 SMA_END_LAUNCH.062 SMA_END_LAUNCH (Big) 142-0701-851 Emerson Johnson530-142-0701-851 Mouser J1,5,9 3 17 SMA_END_LAUNCH.062 SMA_END_LAUNCH (small) 142-0711-821 Emerson Johnson530-142-0711-821 Mouser J6,12,14 3

18 Header 14 Pin TH 14 CONN HEADER VERT SGL 14POS GOLDN2514-6002-RB 3M MHC14K-ND Digikey J15 1

19 Header 2 Pin TH 2 CONN HEADER VERT SGL 2POS 961102-6404-AR 3M 3M9447-ND Digikey J2,3,4,13 4

20 Header 3 Pin TH 3 CONN HEADER VERT SGL 3POS 961103-6404-AR 3M 3M9448-ND Digikey J7,8,10,11 4

21 2:1 Balun SM-22 2:1 Center Tap Balun TC2-72T+ Mini Circuits TC2-72T+ Mini Circuits T1,2 2 22 390 nH 0805 0805CS (2012) Ceramic Chip Inductor 0805CS-391XJLB COILCRAFT 0805CS-391XJLB COILCRAFTL1,2,5,6, 4 23 150nH 0805 0805CS (2012) Ceramic Chip Inductor 0805CS-151XJLB COILCRAFT 0805CS-151XJLB COILCRAFTL3,4,7,8 4 24 30nH 0402 0402CS Ceramic Chip Inductor 0402CS-30NXJLU COILCRAFT 0402CS-30NXJLU COILCRAFTL9-12 4

25 F0562 TQFN-68 Sampling IF receiver F0562 IDT F0562 IDT U1 1

26 PCB 04 Printed Circuit Board F0552 EV Kit Rev 04 CC 1

27 BOM 02 Bill Of Material

Sampling IF Receiver 2300MHz to 2700MHz FlatNoiseTM, Zero-DistortionTM, SIF Rx 35 Rev1, April 2014 IDTF0562NLGI Datasheet F0552NBGI Advance Datasheet TOP MARKINGS IDTF0562 NLGI ZB1344N Q33A009MY Part Number Date Code [YYWW] (Week 44 of 2013) Lot CodeDie Step

TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com Contact Information For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) © 2020 Renesas Electronics Corporation. All rights reserved.

Product Information

F0562 specifications and overview.

Summary

Sampling IF Receiver 2300MHz to 2700MHz

Description

Sampling IF Receiver 2300MHz to 2700MHz

Source title F0562 Datasheet(PDF) - Integrated Device Technology

Related Parts

More parts from the same family.

Browse manufacturer