E3Z-X-ILX OMRON | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 14

Technical content

IO-Link Photoelectric Sensor E3Z-@-IL@ IO-Link Makes Sensor Level Information Visible and Solves the Three Major Issues at Manufacturing Sites! Standard Photoelectric Sensor.

  • Downtime can be reduced.
  • Notifies you of faulty parts and changing conditions in the Sensor in real time.
  • The frequency of sudden failure can be decreased.
  • The incident light level monitor prevents false detection before it happens.
  • The efficiency of changeover can be improved.
  • The batch check for individual sensor IDs significantly decreases commissioning time.
  • Three types of sensing methods and three types of conn ection methods are available.

Ordering Information

IO-Link Model / Sensors [Refer to Dimensions on page 10.] Note: Please contact your OMRON sales representative regarding the IO-Link setup file (IODD file). *1. The Reflector is sold separately. Select the Reflector model most s uited to the application. *2. The sensing distance specified is possible when the E39-R1S is used. Values in parentheses indicate the minimum required distance between the Sensor and Reflector. *3. Through-beam Sensors are sold in sets that include both the Emitter and Receiver. Sensing method Appearance Connection method Sensing distance Baud rate Model PNP Through-beam (Emitter + Receiver) Pre-wired (2 m) COM2 E3Z-T81-IL2 2M Pre-wired M12 connector E3Z-T81-M1TJ-IL2 0.3M Standard M8 connector E3Z-T86-IL2 Pre-wired (2 m) COM E3Z-T81-IL3 2M Pre-wired M12 connector E3Z-T81-M1TJ-IL3 0.3M Standard M8 connector E3Z-T86-IL3 Retro-reflective with MSR function Pre-wired (2 m) *2 COM2 E3Z-R81-IL2 2M Pre-wired M12 connector E3Z-R81-M1TJ-IL2 0.3M Standard M8 connector E3Z-R86-IL2 Pre-wired (2 m) COM3 E3Z-R81-IL3 2M Pre-wired M12 connector E3Z-R81-M1TJ-IL3 0.3M Standard M8 connector E3Z-R86-IL3 For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Be sure to read Safety Precautions on page 9. Red light Infrared light 15 m 4 m (100 mm) (When using E39-R1S)

E3Z-@-IL@ Note: Please contact your OMRON sales representative regarding the IO-Link setup file (IODD file). Accessories (Sold Separately) Slit (A Slit is not provided with Through-beam Sensors) Order a Slit separately if required. Reflectors (Reflector required for Retroreflective Sensors) A Reflector is not provided with the Sensor. Be sure to order a Reflector separately. Note:1. If you use the Reflector at any distance other than the rated distance, make sure that the stability indicator lights properly when you install the Sensor. 2. Refer to Reflectors on E39-L/E39-S/E39-R on your OMRON website for details. * Values in parenthese indicate the minimum required distance between the Sensor and Reflector. Sensing method Appearance Connection method Sensing distance Baud rate Model PNP Diffuse-reflective Pre-wired (2 m) COM2 E3Z-D82-IL2 2M Pre-wired M12 connector E3Z-D82-M1TJ-IL2 0.3M Standard M8 connector E3Z-D87-IL2 Pre-wired (2 m) COM3 E3Z-D82-IL3 2M Pre-wired M12 connector E3Z-D82-M1TJ-IL3 0.3M Standard M8 connector E3Z-D87-IL3 Pre-wired (2 m) COM2 E3Z-L81-IL2 2M Pre-wired M12 connector E3Z-L81-M1TJ-IL2 0.3M Standard M8 connector E3Z-L86-IL2 Pre-wired (2 m) COM3 E3Z-L81-IL3 2M Pre-wired M12 connector E3Z-L81-M1TJ-IL3 0.3M Standard M8 connector E3Z-L86-IL3 Slit width Sensing distance Minimum detectable object (Reference value) Model ContentsE3Z-T@@ 0.5-mm dia. 50 mm 0.2-mm dia. E39-S65A One set (contains Slits for both the Emitter and Receiver) 1-mm dia. 200 mm 0.4-mm dia. E39-S65B 2-mm dia. 800 mm 0.7-mm dia. E39-S65C 0.5 × 10 mm 1 m 0.2-mm dia. E39-S65D 1 × 10 mm 2.2 m 0.5-mm dia. E39-S65E 2 × 10 mm 5 m 0.8-mm dia. E39-S65F Name Sensing distance * Model Quantity RemarksE3Z-R Rated value Reference value Reflector 3 m (100 mm) --- E39-R1 1

  • Reflectors are not provided with Retro-reflective models.
  • The MSR function of the E3Z-R@ is enabled. 4 m (100 mm) --- E39-R1S 1 --- 5 m (100 mm) E39-R2 1 Fog Preventive Coating --- 3 m (100 mm) E39-R1K 1 Small Reflector --- 1.5 m (50 mm) E39-R3 1 Tape Reflector --- 700 mm (150 mm) E39-RS1 1 --- 1.1 m (150 mm) E39-RS2 1 --- 1.4 m (150 mm) E39-RS3 1 Red light Infrared light 1 m 90 mm (narrow beam)

E3Z-@-IL@ Mounting Brackets A Mounting Bracket is not enclosed with the Sensor. Order a Mounting Bracket separately if required. Note:1. When using Through-beam models, order one bracket for the Receiver and one for the Emitter. 2. Refer to Mounting Brackets on E39-L/E39-S/E39-R on your OMRON website for details. *1. Cannot be used for Standard Connector models with mounting surface on the bottom. In that case, use Pre-wired Connector mode ls. *2. Cannot be used for Standard Connector models. Sensor I/O Connectors (Models for Connectors and Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) Note:1. When using Through-beam models, order one connector for the Receiver and one for the Emitter. 2. Refer to Sensor I/O Connectors/Sensor Controllers on your OMRON website for details. *1. Straight type/L-shape type combinations are also available. *2. The connectors will not rotate after they are connected. *3. The cable is fixed at an angle of 180° from the sensor emitter/receiver surface. Appearance Model (material) Quantity Remarks Appearance Model (material) Quantity Remarks E39-L153 (SUS304) *1 1 Mounting Brackets E39-L98 (SUS304) *2 1 Metal Protective Cover Bracket E39-L104 (SUS304) *1 1 E39-L150 (SUS304) 1 (Sensor adjuster) Easily mounted to the aluminum frame rails of conveyors and easily adjusted. For left to right adjust- ment E39-L43 (SUS304) *2 1 Horizontal Mounting Brackets E39-L151 (SUS304) 1 E39-L142 (SUS304) *2 1 Horizontal Protective Cover Bracket E39-L44 (SUS304) 1 Rear Mounting Bracket E39-L144 (SUS304) *2 1 Compact Protective Cover Bracket (For E3Z only) Size Type Appearance Cable length Model M12 Socket on one cable end 2 m XS5F-D421-D80-F 5 m XS5F-D421-G80-F 2 m XS5F-D422-D80-F 5 m XS5F-D422-G80-F Socket and plug on cable ends *1 2 m XS5W-D421-D81-F 5 m XS5W-D421-G81-F 2 m XS5W-D422-D81-F 5 m XS5W-D422-G81-F M8 Socket on one cable end 2 m XS3F-M421-402-A 5 m XS3F-M421-405-A 2 m XS3F-M422-402-A 5 m XS3F-M422-405-A M8 socket/ M12 plug Socket and plug on cable ends 0.2 m XS3W-M42C-4C2-A Smartclick connector Straight *2 Smartclick connector L-shape *2 *3 Smartclick connector Straight/ Straight *2 Smartclick connector L-shape/L-shape *2 *3 Straight *3 L-shape *3 *4 M8-M12 (Smartclick) conversion cable *2

E3Z-@-IL@ Ratings and Specifications IO-Link Model * Values in parentheses indicate the minimum required distance between the Sensor and Reflector. Sensing method Through-beam Retro-reflective with MSR function Diffuse-reflective Narrow-beam Models PNP output Pre-wired E3Z-T81-IL@ E3Z-R81-IL@ E3Z-D82-IL@ E3Z-L81-IL@ Model Pre-wired connector (M12) E3Z-T81-M1TJ-IL@ E3Z-R81-M1TJ-IL@ E3Z-D82-M1TJ-IL@ E3Z-L81-M1TJ-IL@ Item Connector (M8) E3Z-T86-IL@ E3Z-R86-IL@ E3Z-D87-IL@ E3Z-L86-IL@ Sensing distance 15 m 4 m (100 mm) * (when using E39-R1S) 3 m (100 mm) * (when using E39-R1) 1 m (white paper: 300 × 300 mm) 90 + 30 mm (white paper: 100 × 100 mm) Spot diameter (reference value) --- 2.5 dia. and sensing dis- tance of 90 mm Standard sensing object Opaque: 12-mm dia. min. Opaque: 75-mm dia. min. --- Minimum detectable object (reference value) --- 0.1 mm (copper wire) Differential travel (representative example) --- --- 20% max. of setting distance Refer to Engineering data on page 6 Directional angle Both emitter and receiver: 3 to 15° 2 to 10° --- Light source (wavelength) Infrared LED (870 nm) Red LED (660 nm) Infrared LED (860 nm) Red LED (650 nm) Power supply voltage 10 to 30 VDC (including 10% ripple (p-p)) Current consumption 50 mA max. (Emitter: 25 mA max., Receiver: 25 mA max.) 30 mA max. Control output Load power supply voltage: 30 VDC max., Load current: 100 mA max. Residual voltage: Load current of less than 10 mA: 1 V max. Load current of 10 to 100 mA: 2 V max. PNP open collector output Light-ON/Dark-ON selectable Indicators In the Standard I/O mode (SIO mode): Operation indicator (orange, lit) and stability indicator (green, lit) In the IO-Link Mode: Operation indicator (orange, lit) and communication indicator (green, blinking at 1 s intervals) Protection circuits Reversed power supply polarity protection, out- put short-circuit protec- tion, and reversed output polarity protection Reversed power supply polarity protection, output short-circuit protection, reversed output polarity protection, and mutual interference prevention Response time Operate or reset: 1 ms max. Sensitivity adjustment Sensitivity adjuster / IO-Link communications Ambient illumination (Receiver side) Incandescent lamp: 3,000 lx max. Sunlight: 10,000 lx max. Ambient temperature range Operating: −25 to 55°C (with no icing or condensation) Storage: −40 to 70°C (with no icing or condensation) Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation) Insulation resistance 20 MΩ min. at 500 VDC Dielectric strength 1,000 VAC, 50/60 Hz for 1 min Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 3 times each in X, Y, and Z directions Degree of protection IEC 60529 IP67 Connection method Pre-wired cable (standard cable length 2 m), M12 pre-wired connector (standard cable length 0.3 m), M8 connector Weight (packed state) Pre-wired cable (2 m) Approx. 120 g Approx. 65 g Pre-wired connector (M12) Approx. 60 g Approx. 30 g Connector (M8) Approx. 30 g Approx. 20 g Material Case Polybutylene terephthalate (PBT) Display Modified polyarylate Lens Modified polyarylate Methacrylate resin (PMMA) Modified polyarylate Main IO-Link functions Operation mode switching between Light ON and Dark ON, setup of the instability detection level for light receiving and non-light receiving, timer function of the control output and timer time selecting, instability output (IO-Link mode) ON delay timer time selecting, setup of a teaching level and execution of teaching, setup of light receiving sensitivity level, monitor output, operating hours read-out, and initial reset Communication specifications IO-Link specification Ver 1.1 Baud rate -IL3: COM3 (230.4 kbps), -IL2: COM2 (38.4 kbps) Data length PD size: 2 bytes, OD size: 1 byte (M-sequence type: TYPE_2_2) Minimum cycle time -IL3 (COM3): 1 ms, -IL2 (COM2): 2.3 ms Accessories Instruction manual (Neither Reflectors nor Mounting Brackets are provided with any of the above models.)

E3Z-@-IL@ Engineering Data (Reference Value) Parallel Operating Range Through-beam Models Through-beam Models Retro-reflective Models E3Z-T8@-IL@ E3Z-T8@-IL@ and Slit (A Slit is mounted to the Emitter and Receiver.) E3Z-R8@-IL@ and Reflector Operating Range Diffuse-reflective Models Narrow-beam Reflective Models E3Z-D8@-IL@ E3Z-L8@-IL@ Monitor Output vs. Sensing Distance Through-beam Models Retro-reflective Models E3Z-T8@-IL@ E3Z-R8@-IL@ and E39-R1 Reflector 1000 800 600 400 200 −200 −400 −600 −800 1000 40302010 Distance X (m) Distance Y (mm) Y X 250 200 150 100 −50 −100 −150 −200 −250 5 4321 Distance X (m) E39-S65B E39-S65C E39-S65D E39-S65E E39-S65F Y X Distance Y (mm) Y X 200 150 100 −50 −100 −150 −200 8642 Distance X (m) E39-R9 E39-R1SE39-R1 E39-R10 E39-R2 E39-R1K E39-R3 Distance Y (mm) −20 −40 −60 −80 1.61.0 1.20.6 1.40.80.2 0.4 Distance X (m) Y X Sensing object: 300 × 300 mm white paper Distance Y (mm) Y X −10 Sensing object: 100 × 100 mm white paper 50 100 150 200 250 Distance X (mm) Distance Y (mm) 280 260 240 220 200 180 160 140 120 100 05 1 5 10 20 25 30 4535 40 50 Distance (m) Sensitivity adjuster: 1/2 Sensitivity adjuster: MAX Sensitivity adjuster: 1/3 Monitor Output 280 260 240 220 200 180 160 140 120 100 Distance (m) Sensitivity adjuster: 1/2 Sensitivity adjuster: MAX Sensitivity adjuster: 1/3 Monitor Output

E3Z-@-IL@ Monitor Output vs. Sensing Distance Diffuse-reflective Models Narrow-beam Reflective Models E3Z-D8@-IL@ E3Z-L8@-IL@ Sensing Object Size vs. Sensing Distance Diffuse-reflective Models Narrow-beam Reflective Models E3Z-D8@-IL@ E3Z-L8@-IL@ Spot Diameter vs. Sensing Distance Differential Tra vel vs. Sensing Distance Narrow-beam Reflective Models Narrow-beam Reflective Models E3Z-L8@-IL@ E3Z-L8@-IL@ 280 260 240 220 200 180 160 140 120 100 Distance (m) Sensitivity adjuster: 1/2 Sensitivity adjuster: MAX Sensitivity adjuster: 1/3 Monitor Output 280 260 240 220 200 180 160 140 120 100 0 50 100 150 200 300250 350 Distance (mm) Sensitivity adjuster: 1/2 Sensitivity adjuster: MAX Sensitivity adjuster: 1/3 Monitor Output d d 4.5 3.5 2.5 1.5 0.5 350 300250200150100 50 0 Black paper White paper Side length (one side) of sensing object: d (mm) SUS (glossy surface) Distance (m) 300 250 200 150 100 100 30 20 10 7.5 5 3 2 1 0 d d Side length (one side) of sensing object: d (mm) Distance (mm) White paper 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 160 140 1208040 1006020 0 Distance (mm) Spot diameter (mm) 15010075 125500 Distance (mm) Differential travel (mm)

E3Z-@-IL@ I/O Circuit Diagrams Timing Chart Output circuit *1. The operation mode can be changed by the IO-Link communications. *2. The timer function can be set up using the IO-Link communications for control output 1 and 2 separately. (It is able to select ON delay, OFF delay, or one-shot function and select a timer time of 1 to 4000 ms (T).) *3. In the IO-Link mode, if the ON/OFF speed of the sensor is slow, high- speed response of 1 ms or less can be realized using control output 2 as a sensor. *4. The judgment time for the instability detection diagnosis can be selected using the IO-Link communications. (For the ON delay timer function to detect instability, the setting can be selected from 0 (invalid), 10, 50, 100, 300, 500, or 1000 ms. *5. The judgment condition for the light receiving/non-light receiving instability detection function can be selected using the IO-Link communications. (Setting of light receiving instability detection threshold: 500%/400%/300%/200%/140%, setting of non-light receiving instability detection threshold: 70%/50%) ON-delay OFF-delay One shot Present Not present T T Sensing object L ON D ON ON OFF ON OFF T T Present Not present Sensing object L ON D ON ON OFF ON OFF T T Present Not present Sensing object L ON D ON ON OFF ON OFF L ON Opera- tion mode Output mode D ON L ON Standard I/O mode (SIO mode) IO-Link mode D ON ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF Stability indicator (green) *5 Operation indicator (orange) Control output 1 *2 Control output 2 *2 Control output 1 *2 Control output 2 *2 Stability indicator (green) *5 Operation indicator (orange) Flashing (1 s cycle) ON OFF ON OFF Flashing (1 s cycle) ON OFF ON OFF Communication indicator (green) Operation indicator (orange) Control output 1 (Byte1_bit0) *2 Control output 2 *2 *3 Instability detection (Light receiving) (Byte1_bit4) *4*5 Instability detection (Non-light receiving) (Byte1_bit3)*4*5 Communication display lamp (green) Operation display lamp (orange) Control output 1 (Byte1_bit0) *2 Control output 2 *2 *3 Instability detection (Light receiving) (Byte1_bit4) *4*5 Instability detection (Non-light receiving) (Byte1_bit3)*4*5 Unstable operation zone Stable operation zone Stable operation zone /PUF 1MFBTFDPOUBDUZPVS0.30/TBMFTSFQSFTFOUBUJWFSFHBSEJOH BTTJHONFOUPGEBUB Connector Pin Arrangement 2 4 Pre-wired M12 connector E3Z-@81-M1TJ-IL@ E3Z-@82-M1TJ-IL@ E3Z-T81-D-M1TJ-IL@ Standard M8 connector E3Z-@86-IL@ E3Z-@87-IL@ E3Z-T86-D-IL@ 2 4 DO C/Q Brown Black White Blue Photoelectric Sensor 10 to 30VDC Load Load DO C/Q DI C/Q Brown Black White Blue Photoelectric Sensor IO-Link master When using the Sensor connected to IO-Link Master Unit When using as a general sensor Reflective / Receiver of Through-beam Model E3Z-@8@-IL@ Connector Pin Arrangement 2 4 E3Z-T81-L-M1TJ-IL˘ E3Z-T86-L-IL˘ 2 4 Note: Pins 2 is not used. Note: Pins 2 is not used. Emitter of Through-beam Model E3Z-T8@-L-IL@ C/Q Photoelectric Sensor 10 to 30VDC C/Q C/Q Brown Black Blue Brown Black Blue Photoelectric Sensor IO-Link master When using the Sensor connected to IO-Link Master Unit When using as a general sensor

E3Z-@-IL@ Plugs (Sensor I/O Connectors) Nomenclature Brown White Blue Black Wire color XS3F-M421-402-A XS3F-M421-405-A XS3F-M422-402-A XS3F-M422-405-A Through-beam Models (Receiver) Retro-reflective Models Diffuse-reflective Models Pin arrangement Classifi- cation Wire color Connector pin No. Application DC Brown 1 Power supply (+V) White 2 Output DO Blue 3 Power supply (0 V) Black 4 Output C/Q M8 connector M12 connector 1 3 Brown White Blue Black Wire color XS5F-D421-D80-F XS5F-D421-G80-F XS5F-D422-D80-F XS5F-D422-G80-F M8-M12 (Smartclick) conversion cable 2 4 XS3W-M42C-4C2-A Terminal No. Brown White Blue Black Wire color Through-beam Models (Emitter) Pin arrangement Note: Pins 2 is not used. Classifi- cation Wire color Connector pin No. Application DC Brown 1 Power supply (+V) White 2 − Blue 3 Power supply (0 V) Black 4 Output C/Q Through-beam Models E3Z-T8@-IL@ (Receiver) Retro-reflective Models E3Z-R8@-IL@ Diffuse-reflective Models E3Z-D8@-IL@ E3Z-L8@-IL@ In the Standard I/O mode (SIO mode): Stability indicator (green) In the IO-Link mode: IO-Link communication indicator (green) Operation selector Operation indicator (orange) Sensitivity adjuster

E3Z-@-IL@ Safety Precautions Be sure to read the precautions for all models in the website at: www.omron247.com. Warning Indications Meaning of Product Safety Symbols This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. The maximum power supply voltage is 30 VDC. Before turning the power ON, make sure that the power supply voltage does not exceed the maximum voltage. Never use the product with an AC power supply. Otherwise, explosion may result. Do not use the product with voltage in excess of the rated voltage. Excess voltage may result in malfunction or fire. Do not use the product above rated load. Be sure to follow the safety precautions below for added safety. 1. Do not use the sensor under the environment with explosive or ignition gas. 2. Never disassemble, repair nor tamper with the product. 1. Do not use the product under the following conditions. (1) In the place exposed to the direct sunlight. (2) In the place where humidity is high and condensation may occur. (3) In the place where vibration or shock is directly transmitted to the product. 2. Connection and Mounting (1) If the sensor wiring is placed in the same conduits or ducts as high-voltage or high-power lines, inductive noise may cause malfunction or damage. Wire the cables separately or use a shielded cable. (2) Use an extension cable less than 100 m long for Standard I/O mode and less than 20 m for IO-Link mode. (3) Do not exceed the following force values applied to the cable. Tensile: 80 N max., torque: 0.1 Nm max., pressure: 20 N max., flexure: 3 kg max. M8 metal connectors (4) Fasten a fixed implement by hand. If you use pliers, it may cause malfunction or damage to it. 3. Cleaning Do not use thinner, alcohol, or other organic solvents. Otherwise, the optical properties and degree of protection may be degraded. 4. Power supply When using a commercially available switching regulator, be sure to ground the FG (Frame Ground) terminals. 5. Power supply reset time The photoelectric switch will begin sensing no later than 100 ms after the power is turned on. If the load and the photoelectric switch is connected to different power supply, the photoelectric switch must be always turned on first. 6. Turning off the power supply When turning off the power, output pulse may be generated. We recommend turning off the power supply of the load or load line first. 7. Water resistance Though this is type IP67, do not use in the water, rain or outdoors. 8. Please process it as industrial waste. WARNING Warning level Indicates a potentially hazardous situation which, if not avoided, will result in minor or moderate injury, or may result in serious injury or death. Additionally there may be significant property damage. Precautions for Safe Use Supplementary comments on what to do or avoid doing, to use the product safely. Precautions for Correct Use Supplementary comments on what to do or avoid doing, to prevent failure to operate, malfunction or undesirable effect on product performance. General prohibition Indicates the instructions of unspecified prohibited action. Caution, explosion Indicates the possibility of explosion under specific conditions. Caution, fire Indicates the possibility of fires under specific conditions. WARNING Precautions for Safe Use Precautions for Correct Use

E3Z-@-IL@ Dimensions Sensors * Models numbers for Through-beam Sensors (E3Z-T@@) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3Z-T81-IL@-L 2M), the model number of the Receiver, by adding "-D" (example: E3Z-T81-IL@-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. (Unit: mm) Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified. Through-beam Models * Pre-wired Models E3Z-T81-IL@ 2020 32.8 25.4 12.7 4 dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.1 mm), Standard length: 2 m Two, M3 Power indicator/ IO-Link communication indicator (green) Emitter Lens 2.1 3131 10.810.8 7.2 Pins 2 is not used. Terminal No. Specifi- cations 1+ V 2 --- 30 V Output C/Q 4 dia. vinyl-insulated round cable Standard length: 0.3 m Pre-wired M12 connector (E3Z-T@@-M1TJ) 4M12×1 2020 32.8 25.4 12.7 4 dia. vinyl-insulated round cable with 4 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.1 mm), Standard length: 2 m Two, M3 4.511.2 Operation Indicator (orange) 7.5 Sensitivity adjuster Operation selector Receiver Lens 2.1 3131 10.810.8 7.2 Stability indicator/ IO-Link communication indicator (green) Terminal No. Specifi- cations 1+ V

2 Output DO

Through-beam Models * Connector Models E3Z-T86-IL@ M8 connector

10.4 Two, M3

9.75 Emitter 20202.1 12.7 3131 10.810.8 7.2 32.8 25.4 Power indicator/ IO-Link communication indicator (green) Pins 2 is not used. Terminal No. Specifi- cations 1+ V 2 --- 30 V

4 Output C/Q

9.75 Lens Operation Indicator (orange) Sensitivity adjuster Operation selector Receiver Two, M3 2.8 25.4 4.511.2 7.5 12.7 2020 10.810.8 7.2 10.4 2.1 3131 Stability indicator/ IO-Link communication indicator (green) Terminal No. Specifi- cations 1+ V

E3Z-@-IL@ Note: The lens for the E3Z-D @2/D@7 is black. 2.8 25.4 4 dia. vinyl-insulated round cable with 4 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.1 mm), Standard length: 2 m Two, M3 Sensitivity adjuster Operation selector Operation Indicator (orange) 2.1 3131 Receiver Lens 7 dia. Emitter Lens 7 dia. 2020 16.7 10.810.8 32.8 4.511.2 7.5 25.48 Power indicator/ IO-Link communication indicator (green) Retro-reflective Models Pre-wired Models E3Z-R81-IL@ E3Z-D82-IL@ E3Z-L81-IL@ Terminal No. Specifi- cations 1+ V 4 dia. vinyl-insulated round cable Standard length: 0.3 m Pre-wired M12 connector (E3Z-@8@-M1TJ) 4M12×1 Retro-reflective Models Connector Models E3Z-R86-IL@ E3Z-D87-IL@ E3Z-L86-IL@ Two, M3 9.75 Receiver Lens 7 dia. Emitter Lens 7 dia. Sensitivity adjuster M8 connector Operation selector Operation Indicator (orange) 2020 16.7 10.810.8 10.4 2.1 3131 2.8 25.4 4.511.2 7.5 Stability indicator/ IO-Link communication indicator (green) Terminal No. Specifi- cations 1+ V

E3Z-@-IL@ Accessories (Order Separately) Reflectors Refer to E39-R on your OMRON website for details. Sensor I/O Connectors Refer to XS3 or XS5 on your OMRON website for details. Slits E39-S65A E39-S65B E39-S65C A 32.232.2 20.220.2 0.2-mm-thick 10.410.4 12.7 Model Size A Material E39-S65A 0.5 dia. SUS301 stainless steel E39-S65B 1.0 dia. E39-S65C 2.0 dia. Slits E39-S65D E39-S65E E39-S65F Model Size A Material E39-S65D 0.5 SUS301 stainless steel E39-S65E 1.0 E39-S65F 2.0 A 32.232.2 10 0.2-mm-thick 10.410.4 20.220.2 12.7 Mounting Bracket E39-L44 16.2 19.5 14.1 8.7 2727 31.231.2 3636 1.8 23.2 26.2 20° (Mounting dimensions) Mounting Bracket E39-L104 6.7 7.0 4.56 292917.8 26.626.6 12.4 R20 14° 21.5 3939 10° 8.8 (Mounting dimensions)

Terms and Conditions of Sale 1. Offer; Acceptance . These terms and conditions (these "Terms ") are deemed part of all quotes, agreements, purchase orders, acknowledgments, price lists, catalogs, manuals, brochures and other documents, whether electronic or in writing, relating to the sale of products or services (collectively, the "Products by Omron Electronics LLC and its subsidiary companies (“Omron ”). Omron objects to any terms or conditions proposed in Buyer’s purchase order or other documents which are inconsistent with, or in addition to, these Terms. 2. Prices; Payment Terms. All prices stated are current, subject to change with- out notice by Omron. Omron reserves the right to increase or decrease prices on any unshipped portions of outstanding orders. Payments for Products are due net 30 days unless otherwise stated in the invoice. 3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices sent to Buyer after deducting transportation charges, taxes and duties, and will be allowed only if (i) the invoice is paid according to Omron’s payment terms and (ii) Buyer has no past due amounts. 4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 5. Orders . Omron will accept no order less than $200 net billing. 6. Governmental Approvals. Buyer shall be responsible for, and shall bear all costs involved in, obtaining any government approvals required for the impor- tation or sale of the Products. 7. Taxes . All taxes, duties and other governmental charges (other than general real property and income taxes), including any interest or penalties thereon, imposed directly or indirectly on Omron or required to be collected directly or indirectly by Omron for the manufacture, production, sale, delivery, importa- tion, consumption or use of the Products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by Buyer to Omron. 8. Financial. If the financial position of Buyer at any time becomes unsatisfactory to Omron, Omron reserves the right to stop shipments or require satisfactory security or payment in advance. If Buyer fails to make payment or otherwise comply with these Terms or any related agreement, Omron may (without liabil- ity and in addition to other remedies) cancel any unshipped portion of Prod- ucts sold hereunder and stop any Products in transit until Buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid accounts. 9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation unless Buyer indemnifies Omron against all related costs or expenses. 10. Force Majeure . Omron shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron: a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship except in “break down” situations. b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall constitute delivery to Buyer; c. All sales and shipments of Products shall be FOB shipping point (unless oth- erwise stated in writing by Omron), at which point title and risk of loss shall pass from Omron to Buyer; provided that Omron shall retain a security inter- est in the Products until the full purchase price is paid; d. Delivery and shipping dates are estimates only; and e. Omron will package Products as it deems proper for protection against nor- mal handling and extra charges apply to special conditions. 12. Claims. Any claim by Buyer against Omron for shortage or damage to the Products occurring before delivery to the carrier must be presented in writing to Omron within 30 days of receipt of shipment and include the original trans- portation bill signed by the carrier noting that the carrier received the Products from Omron in the condition claimed. 13. Warranties . (a) Exclusive Warranty . Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Li mitations. OMRON MAKES NO WARRANTY OR REPRESENTA TION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL- ITY OR FITNESS FOR A P ARTICULAR PURPOSE OF THE PRO DUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THA T THE PRODUCTS WILL SUITABL Y MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or oth- erwise of any intellectual property right. (c) Buyer Remedy . Omron’s sole obli- gation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsi- ble for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were prop- erly handled, stored, installed and maintained and not subject to contamina- tion, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Compa- nies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environ- ments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron247.com or contact your Omron representative for pub- lished information. 14. Limitation on Liability; Etc . OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT , INCIDENT AL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY , NEGLIGENCE OR STRICT LIABILITY . Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. 15. Indemnities . Buyer shall indemnify and hold harmless Omron Companies and their employees from and against all liabilities, losses, claims, costs and expenses (including attorney's fees and expenses) related to any claim, inves- tigation, litigation or proceeding (whether or not Omron is a party) which arises or is alleged to arise from Buyer's acts or omissions under these Terms or in any way with respect to the Products. Without limiting the foregoing, Buyer (at its own expense) shall indemnify and hold harmless Omron and defend or set- tle any action brought against such Companies to the extent based on a claim that any Product made to Buyer specifications infringed intellectual property rights of another party. 16. Property; Confidentiality. Any intellectual property in the Products is the exclu- sive property of Omron Companies and Buyer shall not attempt to duplicate it in any way without the written permission of Omron. Notwithstanding any charges to Buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of Omron. All information and materials supplied by Omron to Buyer relating to the Products are confidential and proprietary, and Buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. 17. Export Controls. Buyer shall comply with all applicable laws, regulations and licenses regarding (i) export of products or information; (iii) sale of products to “forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of regulated technology or information. 18. Miscellaneous . (a) Waiver. No failure or delay by Omron in exercising any right and no course of dealing between Buyer and Omron shall operate as a waiver of rights by Omron. (b) Assignment . Buyer may not assign its rights hereunder without Omron's written consent. (c) Law. These Terms are governed by the law of the jurisdiction of the home office of the Omron company from which Buyer is purchasing the Products (without regard to conflict of law princi- ples). (d) Amendment . These Terms constitute the entire agreement between Buyer and Omron relating to the Products, and no provision may be changed or waived unless in writing signed by the parties. (e) Severability . If any provi- sion hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. (f) Setoff . Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. (g) Definitions . As used herein, “including” means “including without limitation”; and “Omron Compa- nies” (or similar words) mean Omron Corporation and any direct or indirect subsidiary or affiliate thereof. Certain Precautions on Specifications and Use 1. Suitability of Use . Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Prod- uct in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases but the following is a non-exhaustive list of applications for which particular attention must be given: (i) Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) Use in consumer products or any use in significant quantities. (iii) Energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equip- ment, and installations subject to separate industry or government regulations. (iv) Systems, machines and equipment that could present a risk to life or prop- erty. Please know and observe all prohibitions of use applicable to this Prod- uct. NEVER USE THE PRODUCT FOR AN APPLICA TION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON’S PRO DUCT IS PROP- ERL Y RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. 2. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. 3. Performance Data . Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitabil- ity and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application require- ments. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. 4. Change in Specifications . Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our prac- tice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifica- tions of the Product may be changed without any notice. When in doubt, spe- cial part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. 5. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.

OMRON CANADA, INC. • HEAD OFFICE OMRON ELECTRONICS DE MEXICO • HEAD OFFICE OMRON ELECTRONICS DE MEXICO • SALES OFFICE OMRON ELETRÔNICA DO BRASIL L TDA • HEAD OFFICE OMRON ARGENTINA • SALES OFFICE Cono Sur • 54.11.4783.5300 OMRON CHILE • SALES OFFICE Santiago • 56.9.9917.3920 OTHER OMRON LATIN AMERICA SALES 54.11.4783.5300 Authorized Distributor: Printed on recycled paper. Controllers & I/O

  • Machine Automation Controllers (MAC) • Motion Controllers
  • Programmable Logic Controllers (PLC) • Temperature Controllers • Remote I/O Robotics
  • Industrial Robots • Mobile Robots Operator Interfaces
  • Human Machine Interface (HMI) Motion & Drives
  • Machine Automation Controllers (MAC) • Motion Controllers • Servo Systems
  • Frequency Inverters Vision, Measurement & Identification
  • Vision Sensors & Systems • Measurement Sensors • Auto Identification Systems Sensing
  • Photoelectric Sensors • Fiber-Optic Sensors • Proximity Sensors
  • Rotary Encoders • Ultrasonic Sensors Safety
  • Safety Light Curtains • Safety Laser Scanners • Programmable Safety Systems
  • Safety Mats and Edges • Safety Door Switches • Emergency Stop Devices
  • Safety Switches & Operator Controls • Safety Monitoring/Force-guided Relays Control Components
  • Power Supplies • Timers • Counters • Programmable Relays
  • Digital Panel Meters • Monitoring Products Switches & Relays
  • Limit Switches • Pushbutton Switches • Electromechanical Relays
  • Solid State Relays Software
  • Programming & Configuration • Runtime