E3T-CD11

E3T-CD11 OMRON | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 24

Technical content

Ultracompact, Ultrathin Photoelectric Sensor with Built-in Amplifier E3T The Improved E3T Series with Easier, Smoother Mounting and Installation

• Newly added Through-beam, Long-distance (2 m) Sensors (E3T -ST3@).  Easy installation with M3-mounting Sensors (E3T -ST@@M, E3T -FD@@M, and E3T -SL@@M).  Small Cylindrical Sensors for one-point mounting also added to the Series. (E3T -C@@@(S)). Lineup Overview Sensing method Through-beam Retro- reflective Diffuse- reflective Convergent- reflective BGS- reflectiveAppearance Rectangular type Side-view M2-mounting ●● --- ● --- M3-mounting ● --- --- ● --- Flat M2-mounting ● --- ● --- ● M3-mounting --- --- ● --- --- Cylindrical type Top-view Side-view Be sure to read Safety Precautions on page 13.

Ordering Information

Sensors [Refer to Dimensions on page 14.] Red light Infrared light M2-mounting Sensors A set of mounting screws is included with the Sensor. M3-mounting Sensors A set of mounting screws is not included with the Sensor. Order a Screw Set separately if required. Small Cylindrical Sensors A set of mounting nuts is included with the Sensor. *1. Values in parentheses indicate the minimum required distance between the Sensor and Reflector. *2. The model number of the Emitter is expressed by adding an ”L” to the set model number in the table. Example: E3T-ST11-L 2M The model number of the Receiver is expressed by adding a “D” to the set model number in the table. Example: E3T-ST11-D 2M Orders for individual Emitters and Receivers are accepted. (Modifications are required for some models.) *3. Models are available either with or without the E39-R37-CA Reflector included. Models with E39-R37-CA Reflector. E3T-SR4@-S Models without Reflector. E3T-SR4@-C Sensing method Appearance Sensing distance Operation mode Model NPN output PNP output Through-beam Emitter Receiver Light-ON E3T-ST31 2M E3T-ST33 2M Dark-ON E3T-ST32 2M E3T-ST34 2M Light-ON E3T-ST11 2M E3T-ST13 2M Dark-ON E3T-ST12 2M E3T-ST14 2M Light-ON E3T-ST21 2M E3T-ST23 2M Dark-ON E3T-ST22 2M E3T-ST24 2M Light-ON E3T-FT11 2M E3T-FT13 2M Dark-ON E3T-FT12 2M E3T-FT14 2M Light-ON E3T-FT21 2M E3T-FT23 2M Dark-ON E3T-FT22 2M E3T-FT24 2M Retro- reflective Light-ON E3T-SR41 2M*3 E3T-SR43 2M*3 Dark-ON E3T-SR42 2M*3 E3T-SR44 2M*3 Diffuse- reflective Light-ON E3T-FD11 2M E3T-FD13 2M Dark-ON E3T-FD12 2M E3T-FD14 2M Convergent- reflective Light-ON E3T-SL11 2M E3T-SL13 2M Dark-ON E3T-SL12 2M E3T-SL14 2M Light-ON E3T-SL21 2M E3T-SL23 2M Dark-ON E3T-SL22 2M E3T-SL24 2M BGS- reflective Light-ON E3T-FL11 2M E3T-FL13 2M Dark-ON E3T-FL12 2M E3T-FL14 2M Light-ON E3T-FL21 2M E3T-FL23 2M Dark-ON E3T-FL22 2M E3T-FL24 2M ( ) 2 m (Sensitivity Adjustment Unit can be used.) 1 m (Sensitivity Adjustment Unit can be used.) 300 mm 500 mm 300 mm Using the E39-R4 Reflector provided 200 mm [30 mm] *1 Using the E39-R37-CA 100 mm [10 mm] 5 to 30 mm 5 to 15 mm 5 to 30 mm 1 to 15 mm 1 to 30 mm Sensing method Appearance Sensing distance Operation mode Model NPN output PNP output Through-beam Emitter Receiver Light-ON E3T-ST11M 2M E3T-ST13M 2M Dark-ON E3T-ST12M 2M E3T-ST14M 2M Light-ON E3T-ST21M 2M E3T-ST23M 2M Dark-ON E3T-ST22M 2M E3T-ST24M 2M Diffuse- reflective Light-ON E3T-FD11M 2M E3T-FD13M 2M Dark-ON E3T-FD12M 2M E3T-FD14M 2M Convergent- reflective Light-ON E3T-SL11M 2M E3T-SL13M 2M Dark-ON E3T-SL12M 2M E3T-SL14M 2M Light-ON E3T-SL21M 2M E3T-SL23M 2M Dark-ON E3T-SL22M 2M E3T-SL24M 2M ( ) 1 m 300 mm 5 to 30 mm 5 to 15 mm 5 to 30 mm Sensing method Appearance Sensing distance Operation mode Model NPN output PNP output Through-beam Emitter Receiver Light-ON --- --- Dark-ON E3T-CT12 2M E3T-CT14 2M Light-ON --- --- Dark-ON E3T-CT22S 2M E3T-CT24S 2M Diffuse- reflective (with adjuster) Light-ON E3T-CD11 2M E3T-CD13 2M Dark-ON --- --- ( ) 1 m 500 mm 3 to 50 mm

Variety of Connection Specifications The models with the connection specifications marked with a black circle in the table are available. These are applicable only to M2-mounting Sensors. The model number indication is a combination of the basic model and the connection specification. NPN Output *The sensing distance depends on the Reflector that is used. The sensing distance is 200 mm if an E39-R4 is used and 100 mm if an E39-R37-CA is used. PNP Output *The sensing distance depends on the Reflector that is used. The sensing distance is 200 mm if an E39-R4 is used and 100 mm if an E39-R37-CA is used. Model Model num- ber example E3T-ST11-M1TJ 0.3M E3T-ST11 5M E3T-ST11R 2M E3T-ST11-ECON 0.3M E3T-ST11-ECON 2M Sensing method Sensing distance Operation mode Connection specification M12 pre-wired Smartclick Con- nector (cable length: 0.3 m) Pre-wired (cable length: 5 m) Pre-wired robot (cable length: 2 m) e-CON pre-wired connector (cable length: 0.3 m) e-CON pre-wired connector (cable length: 2 m) Basic model number -M1TJ 0.3M 5M R 2M -ECON 0.3M -ECON 2M Through- beam (side-view) 2 m Light-ON E3T-ST31 ●● ● ● ● Dark-ON E3T-ST32 ●● ● ● ● 1 m Light-ON E3T-ST11 ●● ● ● ● Dark-ON E3T-ST12 ●● ● ● ● 300 mm Light-ON E3T-ST21 ●● --- ●● Dark-ON E3T-ST22 ●● --- ●● Through- beam (flat) 500 mm Light-ON E3T-FT11 ●● ● ● ● Dark-ON E3T-FT12 ●● ● ● ● 300 mm Light-ON E3T-FT21 ● --- --- ●● Dark-ON E3T-FT22 ● --- --- ●● Retro- reflective 200 mm (100 mm) Light-ON E3T-SR41 ●● ● ● ● Dark-ON E3T-SR42 ●● ● ● ● Diffuse- reflective 5 to 30 mm Light-ON E3T-FD11 ●● ● ● ● Dark-ON E3T-FD12 ●● ● ● ● Convergent- reflective 5 to 15 mm Light-ON E3T-SL11 ●● ● ● ● Dark-ON E3T-SL12 ●● ● ● ● 5 to 30 mm Light-ON E3T-SL21 ●● ● ● ● Dark-ON E3T-SL22 ●● ● ● ● BGS- reflective 1 to 15 mm Light-ON E3T-FL11 ● --- ● --- --- Dark-ON E3T-FL12 ● --- ● --- --- 1 to 30 mm Light-ON E3T-FL21 ● --- ●● --- Dark-ON E3T-FL22 ● --- ● --- --- Example: E3T-ST11-M1TJ 0.3M Connection specificationBasic model number Model Model num- ber example E3T-ST13-M1TJ 0.3M E3T-ST13 5M E3T-ST13R 2M Sensing method Sensing distance Operation mode Connection specification M12 pre-wired Smartclick Connector (cable length: 0.3 m) Pre-wired (cable length: 5 m) Pre-wired robot (cable length: 2 m) Basic model number -M1TJ 0.3M 5M R 2M Through- beam (side-view) 2 m Light-ON E3T-ST33 ●● ● Dark-ON E3T-ST34 ●● ● 1 m Light-ON E3T-ST13 ●● ● Dark-ON E3T-ST14 ●● ● 300 mm Light-ON E3T-ST23 ● --- --- Dark-ON E3T-ST24 ● --- --- Through- beam (flat) 500 mm Light-ON E3T-FT13 ●● ● Dark-ON E3T-FT14 ●● ● 300 mm Light-ON E3T-FT23 ● --- --- Dark-ON E3T-FT24 ●● --- Retro- reflective 200 mm (100 mm) Light-ON E3T-SR43 ●● ● Dark-ON E3T-SR44 ●● ● Diffuse- reflective 5 to 30 mm Light-ON E3T-FD13 ●● ● Dark-ON E3T-FD14 ●● ● Convergent- reflective 5 to 15 mm Light-ON E3T-SL13 ●● ● Dark-ON E3T-SL14 ●● ● 5 to 30 mm Light-ON E3T-SL23 ●● ● Dark-ON E3T-SL24 ●● ● BGS- reflective 1 to 15 mm Light-ON E3T-FL13 ● --- ● Dark-ON E3T-FL14 ● --- ● 1 to 30 mm Light-ON E3T-FL23 ● --- ● Dark-ON E3T-FL24 ● --- ●

Accessories (Order Separately) Accessories for M2-mounting Sensors These accessories are not included with the Sensor. Order them separately if required. *1.An arrow indicates the polarization direction. Mutual interference can be prevented by using different polarization directions for adjacent Emitters/Receivers. *2. When using Through-beam Sensors (E3T-ST@@, E3T-FT@@), order one bracket for the Emitter and one for the Receiver. *3. Order two Sets, one for the Emitter and one for the Receiver, for Through-beam Sensors (E3T-ST @@ or E3T-FT@@). This is the Screw Set for mounting the Sensor to the Mounting Bracket. Order this Set if you loose the screws. Do not use this Screw Set to mount the Mounting Bracket to the equipment. *4. This is included with the Sensor. Name Applicable Sensor Model Quantity Dimensions page Remarks Mutual Interference Prevention Filter for Through-beam Side-view Sensors *1 E3T-ST3@ E39-E14 (Two each for Emitter and Receiver) Sensing distance 1 m E3T-ST1@ Sensing distance 0.5 m Slit for Through-beam Side-view Sensors 0.5 dia. E3T-ST3@ E39-S63 (One each for Emitter and Receiver; common with Slit widths of 1 dia. and 0.5 dia.) Sensing distance 200 mm, Minimum detectable object (typical) 0.5-mm dia. E3T-ST1@ Sensing distance 100 mm, Minimum detectable object (typical) 0.5-mm dia. E3T-ST2@ Sensing distance 30 mm, Minimum detectable object (typical) 0.5-mm dia. 1 dia. E3T-ST3@ Sensing distance 600 mm, Minimum detectable object (typical) 1-mm dia. E3T-ST1@ Sensing distance 300 mm, Minimum detectable object (typical) 1-mm dia. E3T-ST2@ Sensing distance 100 mm, Minimum detectable object (typical) 1-mm dia. Slit for Through-beam Flat Sensors 0.5 dia. E3T-FT1@ E39-S64 Sensing distance 50 mm, Minimum detectable object (typical) 0.5-mm dia. E3T-FT2@ Sensing distance 30 mm, Minimum detectable object (typical) 0.5-mm dia. 1 dia. E3T-FT1@ Sensing distance 100 mm, Minimum detectable object (typical) 1-mm dia. E3T-FT2@ Sensing distance 50 mm, Minimum detectable object (typical) 1-mm dia. Sensitivity Adjustment Unit for Through- beam Side-view Sensors E3T-ST3@ E39-E10 1 Sensing distance (typical) 1,200 to 1,800 mm E3T-ST1@ Sensing distance (typical) 300 to 800 mm Mounting Brackets for Side-view Sensors *2 E3T-S@@@ E39-L116 Nut plate providedE39-L117 E39-L118 Mounting Brackets for Flat Sensors *2 E3T-F@@@ E39-L119 --- E39-L120 Screw Set for Side-view Sensors *3*4 E3T-S@@@ E39-L164 2 for each --- Material: Iron (Same type as provided with the Sensor.) Contents: Phillips screws (M2×14), Hexagonal nuts, Spring washers, Flat washers Screw Set for Flat Sensors Material: Iron (Same type as provided with the Sensor.) Contents: Phillips screws (M2×8), Hexagonal nuts, Spring washers, Flat washers SUS Screw Set for Flat Sensors Material: SUS304 Contents: Bolt with hexagonal hole (M2×6) SUS Screw Set for Side-view Sensors *3 E3T-S@@@ E39-L173 2 for each Material: SUS304 Contents: Bolt with hexagonal hole (M2×12), Hexagonal nuts, Spring washers, Flat washers

Accessories for M3-mounting Sensors These accessories are not included with the Sensor. Order them separately if required. *1.When using Through-beam Sensors (E3T-ST@@M), order one bracket for the Emitter and one for the Receiver. *2. This is the Screw Set for mounting the Sensor to the Mounting Bracket. Order this Set if you loose the screws. Do not use this Screw Set to mount the Mounting Bracket to the equipment. Accessories for Small Cylindrical Sensors *1.This Nut Set is for the Emitter/Receiver. This is the Nut Set for mounting the Sensor. Order this Set if you loose the screws. Accessories for All Sensors *1.Values in parentheses indicate the minimum required distance between the Sensor and Reflector. *2. The E3T-SR4@ cannot be used with the E39-R37 or E39-RS1/2/3 (without CA) Tape Reflectors. The E39-@-CA Reflector is for use only with the E3T-SR4@. It cannot be used with other Sensors. Sensor I/O Connectors (Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) Note: When using Through-beam Sensors, order one connector for the Emitter and one for the Receiver. Name Applicable Sensor Model Quantity Dimensions page Remarks Slits for Through-beam Side-view Sensors 0.5 dia. E3T-ST1@M E39-S76A (One each for Emitter and Receiver) Sensing distance 100 mm, Minimum detectable object (typical) 0.5-mm dia. E3T-ST2@M Sensing distance 30 mm, Minimum detectable object (typical) 0.5-mm dia. 1 dia. E3T-ST1@M E39-S76B Sensing distance 300 mm, Minimum detectable object (typical) 1-mm dia. E3T-ST2@M Sensing distance 100 mm, Minimum detectable object (typical) 1-mm dia. Mounting Bracket for Side-view Sensors *1 E3T-S@@@M E39-L166 12 2 Nut plate provided Mounting Bracket for Flat Sensors E3T-FD@@M E39-L167 --- Back-mounting Spacer for Flat Sen- sors E39-L168 Use this Spacer when mounting a Flat Sensor (E3T-FD@@M) from the back. SUS Screw Set for Flat Sensors *2 E3T-FD@@M E39-L170 2 --- Material: SUS304 Contents: Bolt with hexagonal hole (M3×6) SUS Screw Set for Side-view Sen- sors *1*2 E3T-S@@@M E39-L171 2 for each Material: SUS304 Contents: Bolt with hexagonal hole (M3×15), Hex- agonal nuts, Spring washers, Flat washers Name Applicable Sensor Model Quantity Dimensions Page Remarks SUS Nut Set for Through-beam Sensors *1 E3T-CT@@ E3T-CT@@S E39-M5 4 (Hexagonal nuts), 2 (Toothed washers) --- Material: SUS303 (Same type as provided with the Sensor.) SUS Nut Set for Diffuse-reflective Sensors E3T-CD@@ E39-M6 2 (Hexagonal nuts), 1(Toothed washers) Adjustment Driver for Diffuse-reflec- tive Sensors E39-G17 1 This Driver is used to turn the sensitivity adjuster. Provided with E3T-CD@@Name Applicable Sensor Model Quantity Dimensions Page Remarks Small Reflectors (for Retro-reflective Sensors) E3T-SR4@ E39-R4 Sensing distance 200 mm [30 mm] *1 Minimum detectable object 2-mm dia. Provided with the E3T-SR4@ E3T-SR4@-S E39-R37-CA *2 Sensing distance 100 mm [10 mm] *1 Minimum detectable object 2-mm dia. Provided with the E3T-SR4@-S Tape Reflectors (for Retro-reflective Sensors) E3T-SR4@-C E39-RS1-CA Sensing distance 100 mm [10 mm] *1 Minimum detectable object 2-mm dia. Use Tape Reflectors in combination with the E3T-SR4@-C, which does not come with a Reflector. E39-RS2-CA *2 E39-RS3-CA *2 Size Cable Appearance Cable type Model M12 (For -M1TJ models) Standard cable 2 m 4-wire XS5F-D421-D80-A 5 m XS5F-D421-G80-A e-CON 2 m E39-ECON2M 5 m E39-ECON5M 0.5 to 1 m E39-ECONW@M 1.1 to 1.5 m Replace @ with the cable length in 0.1-m increments.1.6 to 2 m Straight Connector on one end Connector on both ends

Ratings and Specifications *1.Values in parentheses indicate the minimum required distance between the Sensor and Reflector. *2. Only the Instruction Manual is included with an M3-mounting Sensor (E3T-ST@@M). Order the Set of Mounting Screws separately if required. Sensing method Through-beam Retro-reflective (without M.S.R. function) Appearance Item Rectangular type (Side-view) Rectangular type (Flat) Cylindrical type (Top-view) Cylindrical type (Side-view) Rectangular type (Side-view) NPN output Light-ON E3T-ST31 E3T-ST11 E3T-ST11M E3T-ST21 E3T-ST21M E3T-FT11 E3T-FT21 --- --- E3T-SR41 Dark-ON E3T-ST32 E3T-ST12 E3T-ST12M E3T-ST22 E3T-ST22M E3T-FT12 E3T-FT22 E3T-CT12 E3T-CT22S E3T-SR42 PNP output Light-ON E3T-ST33 E3T-ST13 E3T-ST13M E3T-ST23 E3T-ST23M E3T-FT13 E3T-FT23 --- --- E3T-SR43 Dark-ON E3T-ST34 E3T-ST14 E3T-ST14M E3T-ST24 E3T-ST24M E3T-FT14 E3T-FT24 E3T-CT14 E3T-CT24S E3T-SR44 Sensing distance 2 m 1 m 300 mm 500 mm 300 mm 1 m 500 mm 200 mm [30 mm] *1 (Using the E39-R4) 100 mm [10 mm] *1 (Using the E39-R37- CA) Standard sensing object Opaque, 3- mm dia. min. mm dia. min. Opaque, 5- mm dia. min. Opaque, 27-mm dia. min. Minimum detectable object (typical) Opaque, 3- Hysteresis (white paper) --- Black/white error --- Directional angle Emitter: 2 to 20° Receiver: 2 to 70° Emitter: 3 to 25° Receiver: 3° min. Receiver: 2° Receiver: 10° 2 to 20° Light source (wavelength) Red LED (650 nm) Red LED (630 nm) Red LED (625 nm) Red LED (650 nm) Power supply voltage 12 to 24 VDC ±10%, ripple (p-p) 10% max. Current consumption 30 mA max. (Emitter 10 mA max., Receiver 20 mA max.) 30 mA max. (Emitter 15 mA max., Receiver 15 mA max.) 20 mA max. Control output Load power supply voltage: 26.4 VDC max. Load current: 50 mA max. (residual voltage: 2 V max. for load current of 10 to 50 mA, 1 V max. for load current of less than 10 mA) Open-collector output Load power supply voltage: 30 VDC max. Load current: 80 mA max. (residual voltage: 1 V max.) Open-collector output Load power supply voltage: 26.4 VDC max. Load current: 50 mA max. (residual volt- age: 2 V max. for load current of 10 to 50 mA, 1 V max. for load current of less than 10 mA) Open-collector output Protection circuits Power supply and control output reverse polarity protection, Output short-circuit protection Power supply reverse polarity protection, Output short-circuit protection Power supply and control output reverse polarity protection, Output short-circuit protection, Mutual interference prevention Response time Operate or reset: 1 ms max. Operate or reset: 0.5 ms max. Operate or reset: 1 ms max. Ambient illumination Incandescent lamp: 5,000 lx max., Sunlight: 10,000 lx max. Incandescent lamp: 3,000 lx max. Incandescent lamp: 5,000 lx max., Sun- light: 10,000 lx max. Ambient temperature range Operating: −25 to +55°C Storage: −40 to +70°C (with no icing or condensation) Operating: −25 to +55°C Storage: −30 to +70°C (with no icing or condensa- tion) Operating: −25 to +55°C Storage: −40 to +70°C (with no icing or condensation) Ambient humidity range Operating: 35% to +85% Storage: 35% to +95% (with no condensation) Operating or Storage: 35% to +85% (with no condensation) Operating: 35% to +85% Storage: 35% to +95% (with no condensation) Insulation resistance 20 MΩ min. at 500 VDC Dielectric strength AC1,000V, 50/60 Hz for 1 min. AC500V, 50/60 Hz for 1 min. AC1,000V, 50/60 Hz for 1 min. Vibration resistance (destruction) 10 to 2,000 Hz, 1.5-mm double amplitude or 300 m/s 2 for 0.5 hours each in X, Y, and Z directions 10 to 55Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions 10 to 2,000 Hz, 1.5-mm double ampli- tude or 300 m/s 2 for 0.5 hours each in X, Y, and Z directions Shock resistance (destruction) 1,000 m/s 2 3 times each in X, Y, and Z directions 500 m/s2 3 times each in X, Y, and Z directions 1,000m/s2 3 times each in X, Y, and Z di- rections Degree of protection IP67 (IEC 60529) IP65 (IEC 60529) IP67 (IEC 60529) Connection method Pre-wired (standard length: 2 m) Weight (packed state) Approx. 40 g Approx. 60 g Approx. 20 g Materi- als Case PBT (polybutylene terephthalate) SUS303 PBT (polybutylene terephthalate) Display window Denatured polyarylate Polysulfone Denatured polyarylate Lens Denatured polyarylate Polysulfone Methacrylc resin Hexagonal nuts --- SUS303 --- Toothed wash- ers --- SUS303 --- Accessories *2 Instruction manual, Phillips screws (Side-view Sensors: M2 × 14, Flat Sensors: M2 × 8), Nuts, Spring washers, Flat washers *2 Instruction manual, Hexago- nal nuts, Toothed washers Instruction manual, Phillips screws (M2×14), Nuts, Spring washers, Flat washers, E39-R4 (E3T-SR4@ only), E39-R37-CA (E3T-SR4@-S only)

*Only the Instruction Manual is included with an M3-mounting Sensor (E3T-FD@@M or E3T-SL@@M). Order the Set of Mounting Screws separately if required. Sensing method Diffuse-reflective Convergent-reflective BGS-reflective Appearance Item Rectangular type (Flat) Cylindrical type (Top-view) Rectangular type (Side-view) Rectangular type (Flat) NPN output Light-ON E3T-FD11 E3T-FD11M E3T-CD11 E3T-SL11 E3T-SL11M E3T-SL21 E3T-SL21M E3T-FL11 E3T-FL21 Dark-ON E3T-FD12 E3T-FD12M --- E3T-SL12 E3T-SL12M E3T-SL22 E3T-SL22M E3T-FL12 E3T-FL22 PNP output Light-ON E3T-FD13 E3T-FD13M E3T-CD13 E3T-SL13 E3T-SL13M E3T-SL23 E3T-SL23M E3T-FL13 E3T-FL23 Dark-ON E3T-FD14 E3T-FD14M --- E3T-SL14 E3T-SL14M E3T-SL24 E3T-SL24M E3T-FL14 E3T-FL24 Sensing distance 5 to 30 mm (50 × 50 mm white paper) 3 to 50 mm (100 × 100 mm white paper) 5 to 15 mm (50 × 50 mm white paper) 5 to 30 mm (50 × 50 mm white paper) 1 to 15 mm (50 × 50 mm white paper) 1 to 30 mm (50 × 50 mm white paper) Standard sensing object --- Minimum detectable object (typical) 0.15-mm dia. (sensing distance 10 mm) --- 0.15-mm dia. (sensing distance 10 mm) 0.15-mm dia. non-glossy object (sensing distance 10 mm) Hysteresis (white paper) 6 mm max. 15% or less of the sensing Black/white error --- 15% max. Directional angle --- Light source (wavelength) Red LED (650 nm) Infrared LED (870 nm) Red LED (650 nm) Power supply voltage 12 to 24 VDC ±10%, ripple (p-p) 10% max. Current consumption 20 mA max. Control output Load power supply voltage: 26.4 VDC max. Load current: 50 mA max. (re- sidual voltage: 2 V max. for load current of 10 to 50 mA, 1 V max. for load current of less than 10 mA) Open-collector output Load power supply voltage: 30 VDC max. Load current: 80 mA max. (residual voltage: 1 V max.) Open-collector output Load power supply voltage: 26.4 VDC max. Load current: 50 mA max. (residual voltage: 2 V max. for load cur- rent of 10 to 50 mA, 1 V max. for load current of less than 10 mA) Open-collector output Protection circuits Power supply and control output reverse polarity protection, Output short-circuit protection, Mutual interference prevention Power supply reverse polarity protection, Output short-circuit protection Power supply and control output reverse polarity protection, Output short-circuit protection, Mutual interference prevention Response time Operate or reset: 1 ms max. Operate or reset: 0.5 ms max. Operate or reset: 1 ms max. Ambient illumination Incandescent lamp: 5,000 lx max., Sunlight: 10,000 lx max. Incandescent lamp: 3,000 lx max. Incandescent lamp: 5,000 lx max., Sunlight: 10,000 lx max. Ambient temperature range Operating: −25 to +55°C Storage: −40 to +70°C (with no icing or condensation) Operating: −25 to +55°C Storage: −30 to +70°C (with no icing or condensation) Operating: −25 to +55°C Storage: −40 to +70°C (with no icing or condensation) Ambient humidity range Operating: 35% to +85% Storage: 35% to +95% (with no condensation) Operating or Storage: 35% to +85% (with no condensation) Operating: 35% to +85% Storage: 35% to +95% (with no condensation) Insulation resistance 20 MΩ min. at 500 VDC Dielectric strength 1,000 VAC, 50/60 Hz for 1 min. 500 VAC, 50/60 Hz for 1 min. 1,000 VAC, 50/60 Hz for 1 min. Vibration resistance (destruction) 10 to 2,000 Hz, 1.5-mm double amplitude or 300 m/s 2 for 0.5 hours each in X, Y, and Z directions 10 to 55Hz, 1.5-mm double am- plitude for 2 hours each in X, Y, and Z directions 10 to 2,000 Hz, 1.5-mm double amplitude or 300 m/s2 for 0.5 hours each in X, Y, and Z directions Shock resistance (destruction) 1,000 m/s2 3 times each in X, Y, and Z directions 500 m/s2 3 times each in X, Y, and Z directions 1,000m/s2 3 times each in X, Y, and Z directions Degree of protection IP67 (IEC 60529) IP65 (IEC 60529) IP67 (IEC 60529) Connection method Pre-wired (standard length: 2 m) Weight (packed state) Approx. 20 g Approx. 40 g Approx. 20 g Materi- als Case PBT (polybutylene terephtha- late) SUS303 PBT (polybutylene terephthalate) Display window Denatured polyarylate Epoxy Denatured polyarylate Lens Denatured polyarylate Polysulfone Denatured polyarylate Hexagonal nuts --- SUS303 --- Toothed wash- ers --- SUS303 --- Accessories * Instruction manual, Phillips screws(M2 × 8), Nuts, Spring washers, Flat washers Instruction manual, Hexagonal nuts, Toothed washers, Adjust- ment driver Instruction manual, Phillips screws(M2 × 14), Nuts, Spring washers, Flat washers Instruction manual, Phillips screws(M2 × 8), Nuts, Spring washers, Flat washers

Engineering Data (Typical) M2-mounting and M3-mounting Sensors Parallel Operating Range Through-beam E3T-ST3@ + E39-S63 Slit (A Slit is mounted to the Emitter and Receiver.) E3T-ST@@ + E39-E14 Mutual interference prevention filter (A Slit is mounted to the Emitter and Receiver.) E3T-ST1@(M) + E39-S63 Slit (A Slit is mounted to the Emitter and Receiver.) E3T-ST1@(M) + E39-S63 Slit (Enlarged graph) (A Slit is mounted to the Emitter and Receiver.) E3T-ST2@(M) + E39-S63 Slit (A Slit is mounted to the Emitter and Receiver.) E3T-FT1@ + E39-S64 Slit (A Slit is mounted to the Emitter and Receiver.) E3T-FT1@ + E39-S64 Slit (Enlarged graph) (A Slit is mounted to the Emitter and Receiver.) E3T-FT2@ + E39-S64 Slit (A Slit is mounted to the Emitter and Receiver.) Retro-reflective E3T-SR4@ Operating Range Diffuse-reflective Convergent-reflective E3T-FD1@(M) E3T-SL1@(M) E3T-SL2@(M) 200 150 100 −50 −100 −150 −200 X Y 0.5-dia Slit Distance X (m) 1.0-dia Slit Distance Y (mm) Without Slit 100 −20 −40 −60 −80 −100 E3T -ST1@ E3T -ST3@ X Y Distance X (m) Distance Y (mm) 200 150 100 −50 −100 −150 −200 X Y 0.5-dia Slit Distance X (m) 1-dia Slit Distance Y (mm) Without Slit −20 −40 −60 −80 40 80 120 160 200 X Y Distance Y (mm) 1-dia Slit 0.5-dia Slit Distance X (mm) −10 −15 −20 −25 200 400 800600 X Y Without Slit Distance X (mm) Distance Y (mm) 1-dia Slit 0.5-dia Slit 200 150 100 −50 −100 −150 −200 Y 1-dia Slit Without Slit Distance X (m) Distance Y (mm) 0.5-dia Slit X −20 −40 −60 −80 40 80 120 160 200 Y Distance Y (mm)0.5-dia Slit 1-dia Slit Distance X (mm) X −20 −40 −60 −80 200 400 600 800 Y 1-dia Slit Distance X (mm) Distance Y (mm) Without Slit 0.5-dia Slit X −10 −20 −30 −40 400100 200 300 Y X E3T-SR4@+E39-R4 E3T-SR4@+E39-R37-CA Distance Y (mm) Distance X (mm) 10 20 30 40 Y XSensing object: 50 x 50 mm white paper Distance Y (mm) Distance X (mm) −10 −15 51 01 52 02 53 0 Y X Distance Y (mm) Sensing object: 50 x 50 mm white paper Distance X (mm) 10 20 30 40 Y X Distance Y (mm) Sensing object: 50 x 50 mm white paper Distance X (mm)

Inclination Detection Area Characteristic BGS-reflective Convergent-reflective E3T-FL1@ E3T-FL2@ E3T-SL1@(M) (Top to Bottom) E3T-SL1@(M) (Right to Left) E3T-SL2@(M) (Top to Bottom) E3T-SL2@(M) (Right to Left) BGS-reflective E3T-FL1@ (Top to Bottom) E3T-FL1 @ (Right to Left) E3T-FL2@ (Top to Bottom) Excess Gain vs. Set Distance Through-beam E3T-FL2@ (Right to Left) E3T-ST1 @(M)/E3T-ST3@ E3T-ST2@(M) 26 8 41 0 12 14 16 Y X Distance X (mm) Distance Y (mm) Sensing object: 50 x 50 mm white paper −10 51 5 2 010 25 30 35 Y X Distance X (mm) Distance Y (mm) Sensing object: 50 x 50 mm white paper 100−10 Distance (mm) Angle θ (°) Glass t: 0.7 mm Stainless steel Angle of inclination−θ +θ 100−10 Distance (mm) Angle θ (°) Stainless steel Angle of inclination−θ +θ Glass t: 0.7 mm 100−10 Angle θ (°) Stainless steel Distance (mm) Angle of inclination−θ+θ Glass t: 0.7 mm 20 100−10 Angle θ (°) Stainless steel Distance (mm) Angle of inclination−θ +θ Glass t: 0.7 mm 100−10 Stainless steel Angle θ (°) Distance (mm) Angle of inclination White paper Center line Glass t: 0.7 mm 100−10 Angle θ (°) Distance (mm) Angle of inclination White paper Center line Stainless steel Glass t: 0.7 mm 100−10 Angle θ (°) Stainless steel Distance (mm) Angle of inclination White paper Center line Glass t: 0.7 mm 100−10 Stainless steel Angle θ (°) Angle of inclination White paper Center line Distance (mm) Glass t: 0.7 mm 100 0.5 0.3 0.1 40003000200010000 E3T -ST3@ E3T -ST1@(M)Operating level Set distance (mm) Excess gain ratio 12009006003000 Operating level Set distance (mm) Excess gain ratio

E3T-FT1@ E3T-FT2@ E3T-SR4@ Diffuse-reflective Convergent-reflective E3T-FD1@(M) E3T-SL1@(M) E3T-SL2@(M) Sensing Object Size vs. Sensing Distance Sensing Distance vs. Material Convergent-reflective Diffuse/Convergent-reflective Conve rgent-reflective E3T-SL1@(M) E3T-FD1@(M)/E3T-SL2@(M) E3T-SL1@(M) Diffuse-reflective BGS-reflective E3T-SL2@(M) E3T-FD1@(M) E3T-FL1@ 100 0.5 0.3 0.10 400 800 1200 1600 2000 Excess gain ratio Operating level Set distance (mm) 0 2000150010005000 Excess gain ratio Operating level Set distance (mm) 100 0.5 0.3 0.1 3002001000 Set distance (mm) Excess gain ratio Operating level E3T-SR4@+E39-R37-CA E3T-SR4@+E39-R4 100 0.5 0.3 0.10 10 20 30 40 Excess gain ratio Operating level Black paper White paper Set distance (mm) 0 5 10 15 20 1000 500 300 100 0.5 0.3 0.1 Excess gain ratio Operating level Black paper White paper Set distance (mm) 100 0.5 0.3 0.10 10 20 30 40 Excess gain ratio Operating level White paper Black paper Set distance (mm) 2.0 1.6 1.2 0.8 0.4 0 5 10 15 20 Min. sensing object dia. (mm) Set distance (mm) 0 5 10 15 20 25 30 E3T -FD1@(M) E3T -SL2@(M) Min. sensing object dia. (mm) Sensing object: Pin-gauge, stainless steel Set distance (mm) Material Sensing distance (mm) White paper Stainless Plywood Cardboard Glass sheet Black rubber Black paper Sensing distance (mm) Material White paper Stainless Plywood Cardboard Glass sheet Black rubber Black paper Sensing distance (mm) Material White paper Stainless Plywood Cardboard Glass sheet Black rubber Black paper Sensing distance (mm) Material White paper Stainless Plywood Cardboard Glass sheet Black rubber Black paper

Sensing Distance Characteristics of Sensitivity Adjustment Unit (when Completing Optical Axis Adjustment) E3T-FL2@ E3T-ST1@ + E39-E10 Sensitivity Adjustment Unit E3T-ST3@ + E39-E10 Sensitivity Adjustment Unit Parallel Operating Range Through-beam E3T-CT1@ E3T-CT2@S (Top to Bottom) E3T-CT2@S (Right to Left) Operating Range Sensing Distance vs. Material Diffuse-reflective Diffuse-reflective E3T-CD1@ E3T-CD1@ Sensing distance (mm) Material White paper Stainless Plywood Cardboard Glass sheet Black rubber Black paper Min 1/3 1/2 2/3 Max 3.5 3.0 2.5 2.0 1.5 1.0 0.5 E3T -ST3@ E3T -ST1@ Adjustment dial angle Sensing distance (m) −20 −40 −60 −80 Y X Distance X (m) Distance Y (mm) 200 150 100 −50 −100 −150 −200 Y X Distance X (m) Distance Y (mm) 200 150 100 −50 −100 −150 −200 Y X Distance X (m) Distance Y (mm) −10 −15 −20 20 3010 40 50 60 70 80 Y X Distance X (m) Distance Y (mm) Sensing object: 100 x 100 mm white paper 120 110 100 Sensing distance (mm) Material White paper Stainless Plywood Cardboard Glass sheet Black rubber Black paper

Plugs (Sensor I/O Connectors) Model Operation mode Timing charts Output circuit E3T-@@@1 E3T-@@@1M Light-ON E3T-@@@2 E3T-@@@2M E3T-@@@2S Dark-ON Light incident Light interrupted Operation indicator (orange) ON OFF Output transistor Load (e.g., relay) Operate Reset ON OFF (Between brown (1) and black (4) leads) ZD 0 V Through-beam Receivers and Reflective Sensors Operation indicator (orange) Stability indicator (green) Photo- electric Sensor Main Circuit Brown Black Blue (Control output) 12 to 24 VDC Load (relay) Through-beam Emitters Brown Blue 12 to 24 VDC Photo- electric Sensor Main Circuit 50 mA max.*2 2 4 Note: Pin 2 is not used. Pins 2 and 4 are not used with Through- beam Emitters. *1.There is no diode for Small Cylindrical Sensors (E3T-C@@@(S)). *2. This is 80 mA max. for Small Cylindrical Sensors (E3T-C@@@(S)). *3. These connectors do not apply to the E3T- Connector Pin Arrangement e-CONM12 Operation indicator (orange) ON OFF Output transistor Load (e.g., relay) Operate Reset ON OFF (Between brown (1) and black (4) leads) Light incident Light interrupted Model Operation mode Timing charts Output circuit E3T-@@@3 E3T-@@@3M Light-ON E3T-@@@4 E3T-@@@4M E3T-@@@4S Dark-ON Operation indicator (orange) ON OFF Output transistor Load (e.g., relay) Operate Reset ON OFF (Between blue (3) and black (4) leads) Light incident Light interrupted 0 V ZD Through-beam Receivers and Reflective Sensors Through-beam Emitters Operation indicator (orange) Stability indicator (green) Photo- electric Sensor Main Circuit Photo- electric Sensor Main Circuit Brown Blue 12 to 24 VDC 50 mA max. Brown Black Blue 12 to 24 VDC Load (relay) (Control output) 2 4 Note: Pin 2 is not used. Pins 2 and 4 are not used with Through- beam Emitters. Connector Pin Arrangement*3 e-CONM12 *1.There is no diode for Small Cylindrical Sensors (E3T-C@@@(S)). *2. This is 80 mA max. for Small Cylindrical Sensors (E3T-C@@@(S)). *3. These connectors do not apply to the E3T- Operation indicator (orange) ON OFF Output transistor Load (e.g., relay) Operate Reset ON OFF (Between blue (3) and black (4) leads) Light incident Light interrupted 1 3 XS5F-D421-D80-A (cable length: 2 m) XS5F-D421-G80-A (cable length: 5 m) Brown Blue White Black Wire color Pin arrangement Note: Pin 2 is not used. Pin 2 and 4 are not used with Through-beam Emitters. Classi- fication Wire color Connector pin No. Application DC Brown 1 Power supply (+V) White 2 --- Blue 3 Power supply (0 V) Black 4 Output 1 2 3 4 E39-ECON@M E39-ECONW@M 1 2 3 4 4 3 12 e-CON connectorM12 Connector

Refer to Warranty and Limitations of Liability. This product is not designed or rated for ensuring safety of persons. Do not use it for such purpose. Do not apply AC power to the E3T, otherwise the E3T may rupture. Do not use the product in atmospheres or environments that exceed product ratings.

• Wiring The maximum power supply voltage is 26.4 VDC. Before turning the power ON, make sure that the power supply voltage be not more than maximum voltage. Load short-circuit protection The E3T incorporates a load short-circuit protection function. If the load short-circuits, the output of the E3T will be turned OFF. Then, recheck the wiring and turn on the E3T again to reset the load short- circuit protection function. The load short-circuit protection function will work if there is a current flow that is 1.5 times larger than the rated load current. When using a capacitance load, be sure that the inrush current will not exceed 1.5 times larger than the rated current.
• Mounting When mounting the Sensor, never strike it with a heavy object, such as a hammer. Doing so may reduce its watertight properties. Use screws with spring, flat, or toothed washers to secure the Sensor. Tightening Torque M2-mounting Sensors: 0.15 N·m max M3-mounting Sensors: 0.5 N·m max Small Cylindrical Sensors: 1 N·m max Mounting the Sensor on Moving Parts Consider models that use break resistant cables (e.g., Robotics Cables) if the Sensor will be mounted on a moving part, such as a robot hand. The flexing resistance of Robotics Cable at approximately 400 thousand times is far superior to that of standard cable at approximately 14 thousand times. Cable Bending Rupture Test (Tough Cable Breaking Test) The cable is repeatedly bent with power supplied to check the number of bends until the current is turned OFF.
• Adjusting Indicators
• The following graphs indicate the status of each operating level.
• Be sure to use the E3T within the stable operating range. Use of E39-E10 Sensitivity Adjustment Unit (Dark-ON: E3T-ST12) 1. Mount the Unit on the Receiver. 2. Set the adjuster of the Sensitivity Adjustment Unit to Max. (Before shipping: Max.) 3. After mounting on the Sensor, adjust the optical axis and secure the Sensor. 4. Place a workpiece between the Emitter and Receiver and gradually turn the adjuster counterclockwise toward the Min. side. Stop turning the adjuster when the operation indicator and stability indicator (green) turn ON. 5. Remove the workpiece and confirm that the operation indicator is OFF and the stability indicator (green) is ON. This completes the adjustment. Note: If the light attenuation rate due to a workpiece is 40% or less, the stability indicator will not turn ON whether or not light is received. When the variation of light is small such as when sensing semi-transparent workpieces, carefully perform preliminary testing. E3T-CD@@ Sensitivity Adjustment Use the special screwdriver that is provided with the Sensor to adjust the sensitivity. Do not exceed 0.8 N·m when turning the adjuster.
• Others Do not install the E3T in the following locations.
• Locations subject to excessive dust or dirt
• Locations subject to direct sunlight
• Locations subject to corrosive gas
• Locations subject to contact with organic solvents
• Locations subject to vibration and shock
• Locations subject to contact with water, oil, or chemicals
• Locations subject to high humidities that might result in condensation WARNING Precautions for Correct Use Specimen Standard cable 2.4-mm dia. (7/0.127-mm dia.), 3 conductors Robotics cable 2.4-mm dia. (20/0.08-mm dia.), 3 conductorsTest Con- tents/ condi- tions Bending angle (θ) 90° each to the left and right Bending speed 50 times/min Load 200 g Operation per bend Once in 1 to 3 in the diagram Curvature radius of support point (R) 5 mm Result Approx. 14,000 times Approx. 400,000 times θ θ Weight R A C B Stable operation range Unstable operation range Stable operation range Operating level x 1.2 Operating level Operating level x 0.8 Light ON ON ON ON OFF OFF OFF Stability indicator (green) Operation indicator (orange) E3T -@@@1 E3T -@@@3 E3T -@@@2 E3T -@@@4 * If the E3T fs operating level is set to the stable operation range, the E3T will be in most reliable operation without being influenced by temperature change, voltage fluctuation, dust, or setting change. If the operating level cannot be set to the stable operation range, pay attention to environmental changes while operating the E3T. Indicator Adjuster (At Min) (At Center) (At Max.)

(Unit: mm) Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. Two, M2 holes 9±0.2 7 7 7.7 2.7 3.8 3.9 2.2 4.8 9.5 9.5 14.6 14.6 2.4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Emitter lens (1.3 dia.) Mounting Holes Two, 2.2 dia. * *The mounting holes are made of SUS301. M2-mounting Sensors Through-beam Side-view Sensors E3T-ST1@ (Emitter) E3T-ST2@ (Emitter) E3T-ST3@ (Emitter) Emitter: E3T-ST@@-L Receiver: E3T-ST@@-D M12 Smartclick Pre-wired Connector Model (E3T-ST@@-M1TJ/E3T-FT@@-M1TJ) M12 2.4-dia. vinyl-insulated round cable with 2 or 3 conductors Standard length: 0.3 m e-CON Pre-wired Connector Model (E3T-ST@@-ECON/E3T-FT@@-ECON) 152 5.9 15.6 2.4-dia. vinyl-insulated round cable with 2 or 3 conductors Standard lengths: 0.3 m and 2 m Termi- nal No. Specifica- tions 1+ V 2 --- 30 V

4 Output

(receiver only) *Refer to Mounting the Sensor on Moving Parts on page 13 for details on Robotics Cable models. Two, M2 holes 9±0.2 7 7 7.7 2.7 3.8 3.9 2.2 4.8 14.6 9.5 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Operation indicator Two, 2.2 dia. * Receiver lens * Stability indicator Mounting Holes *The receiver lens diameters are given below. Model Receiver lens diameter E3T-ST1@-D E3T-ST2@-D (1.3 dia.) E3T-ST3@-D (2.4 dia.) E3T-ST1@ (Receiver) E3T-ST2@ (Receiver) E3T-ST3@ (Receiver) *The mounting holes are made of SUS301. 3.53.5 1.75 1.75 4.4 12 12 3.2 8.6 15.815.8 8±0.2 Two, M2 holes Emitter lens (1.3 dia.) 2.4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Two, 2.2 dia. * Mounting Holes Through-beam Flat Sensors E3T-FT1@ (Emitter) E3T-FT2@ (Emitter) Emitter: E3T-FT@@-L Receiver: E3T-FT@@-D *The mounting holes are made of SUS301. E3T-FT1@ (Receiver) E3T-FT2@ (Receiver) 3.2 1.75 4.4 3.53.53.53.5 8.6 15.815.8 12 12 8±0.2 Two, M2 holes Operation indicator Receiver lens (1.3 dia.) Two, 2.2 dia. * 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Stability indicator Mounting Holes *The mounting holes are made of SUS301.

9.2 4.5 3.8 3.9 6.3 1111 15±0.2 3.7 20.620.6 Two, M2 holes Operation indicator Mounting Holes 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Lens (2.0 dia.) Two, 2.2 dia. * Stability indicator Retro-reflective Side-view Sensors E3T-SR4@ *The mounting holes are made of SUS301. M12 Smartclick Pre-wired Connector Model (E3T-SR@@-M1TJ/E3T-FD@@-M1TJ/ E3T-SL@@-M1TJ) M12 2.4-dia. vinyl-insulated round cable with 3 conductors Standard length: 0.3 m e-CON Pre-wired Connector (E3T-SR@@-ECON/E3T-FD@@-ECON/ E3T-SL@@-ECON) 152 5.9 15.6 2.4-dia. vinyl-insulated round cable with 3 conductors Standard lengths: 0.3 m and 2 m Terminal No. Specifi- cations 1+ V 2- - - 30 V *Refer to Mounting the Sensor on Moving Parts on page 13 for details on Robotics Cable models. 20.8 20.8 12 12 3.5 3.5 1.75 13.4 4.4 19 20.8 3.2 8±0.2 Two, M2 holes Operation indicator 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Stability indicator Receiver lens (2.0 dia.) Two, 2.2 dia. * Emitter lens (1.5 dia.) Mounting Holes Diffuse-reflective Flat Sensors E3T-FD1@ *The mounting holes are made of SUS301. 7 7 9.2 3.8 3.9 6.3 11 11 3.7 20.6 20.6 15±0.2 Two, M2 holes Operation indicator 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Emitter lens (4.0 dia.) Receiver lens (4.0 dia.) Two, 2.2 dia. * Stability indicator Mounting Holes Convergent-reflective Side-view Sensors E3T-SL1@ E3T-SL2@ *The mounting holes are made of SUS301.

12 12 3.5 3.5 1.75 3.2 4.4 7.4 20.8 20.8 8±0.2 Two, M2 holes Operation indicator Receiver lens (2.8 square) Emitter lens (1.5 dia.) Two, 2.2 dia. * 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Stability indicator Mounting Holes *Refer to Mounting the Sensor on Moving Parts on page 13 for details on Robotics Cable models. M12 2.4-dia. vinyl-insulated round cable with 3 conductors Standard length: 0.3 m M12 Smartclick Pre-wired Connector Model (E3T-FL@@-M1TJ) 152 5.9 15.6 2.4-dia. vinyl-insulated round cable with 3 conductors Standard lengths: 0.3 m and 2 m e-CON Pre-wired Connector (E3T-FL@@-ECON) BGS-reflective Flat Sensors E3T-FL1@ E3T-FL2@ Termi- nal No. Specifi- cations 1 +V 2 --- 3 0 V *The mounting holes are made of SUS301. Two, M3 holes 7 12.812.8 13±0.2 2.5 6.5 13 2222 6.3 3.9 2.4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Emitter lens (1.3 dia.) Mounting Holes Two, 3.2 dia. * M3-mounting Sensors Through-beam Side-view Sensors E3T-ST1@M (Emitter) E3T-ST2@M (Emitter) Emitter: E3T-ST@@M-L Receiver: E3T-ST@@M-D *The mounting holes are made of SUS304. 7 12.812.8 6.3 6.5 2.5 2222 3.9 Two, M3 holes 13±0.2 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Operation indicator Receiver lens (1.3 dia.) Stability indicator Mounting Holes Two, 3.2 dia. * E3T-ST1@M (Receiver) E3T-ST2@M (Receiver) *The mounting holes are made of SUS304.

4.2 12.6 1616 3.5 14.8 20.4 23.423.4 3.1 Two, M3 holes 10±0.2 Operation indicator 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Stability indicator Receiver lens (2.0 dia.) Two, 3.2 dia. * Emitter lens (1.5 dia.) Mounting Holes Diffuse-reflective Flat Sensors E3T-FD1@M *The mounting holes and plate are made of SUS304. 2.5 6.3 3.9 12.812.87 2222 4.8 Two, M3 holes 16±0.2 Operation indicator 2.4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.1 mm² (AWG27), Insulator diameter: 0.7 mm), Standard length: 2 m Emitter lens (4.0 dia.) Receiver lens (4.0 dia.) Two, 3.2 dia. * Stability indicator Mounting Holes Convergent-reflective Side-view Sensors E3T-SL1@M E3T-SL2@M *The mounting holes are made of SUS304. 8 26.226.2 3.5 M5×0.5M5×0.5 2.5 9.7 4.4 5.6 dia. (1.8) 2.5-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.15 mm² (AWG25), Insulator diameter: 0.8 mm), Standard length: 2 m Mounting Hole 10 dia. 5.5 +0.5 Optical axis Toothed washerTwo, hexagonal nuts (M5) 10 dia. (1) 26.226.2 3.5 M5×0.5M5×0.5 2.5 9.7 4.4 5.6 dia. 5.5 +0.5 Optical axis Two, hexagonal nuts (M5) Toothed washer Operation Indicator 2.7-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.15 mm² (AWG25), Insulator diameter: 0.85 mm), Standard length: 2 m Stability indicator Mounting Hole Small Cylindrical Sensors Through-beam Top-view Sensors E3T-CT1@ (Emitter) E3T-CT1@ (Receiver) Emitter: E3T-CT1@-L Receiver: E3T-CT1@-D

27.227.2 13.1 3.56.2 2.2 M5×0.5M5×0.5 2.5 9.7 10 dia. 5.6 dia. 5.5 +0.5 Optical axis Two, hexagonal nuts (M5) Toothed washer Operation indicator 2.7-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.15 mm² (AWG25), Insulator diameter: 0.85 mm), Standard length: 2 m Stability indicator Mounting Hole 6.2 27.227.2 3.513.1 2.5 9.7 2.2 M5×0.5M5×0.5 10 dia. 5.6 dia. 5.5 +0.5 Optical axis Two, hexagonal nuts (M5) Toothed washer 2.5-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.15 mm² (AWG25), Insulator diameter: 0.8 mm), Standard length: 2 m Mounting Hole Through-beam Side-view Sensors E3T-CT2@S (Emitter) E3T-CT2@S (Receiver) Emitter: E3T-CT2@S-L Receiver: E3T-CT2@S-D 2.4 dia. M6×0.75M6×0.75 22.6 19.9 2.8 6.517 29.129.1 6.8 dia. 11 dia. (1.2) 6.5 +0.5 Optical axis Two, hexagonal nuts (M6) Toothed washer Operation indicator 2.7-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.15 mm² (AWG25), Insulator diameter: 0.85 mm), Standard length: 2 m Stability indicator Mounting Hole Sensitivity adjusterDiffuse-reflective Top-view Sensors E3T-CD1@ 13.7 9.7 8.7 23 19 18 Two, 2.2 dia. 1.4 4.9 4.7 Reflector (Provided with E3T-SR4@) E39-R4 Material, reflective surface: acrylic Rear surface: ABS 10.2 8.7 13.7 13.7 18.3 23 18.3 23 (1.1) Two, R1.55 Mounting bracket Reflector Reflective surface: acrylic Mounting Bracket: t 0.5 Reflector: t 0.5 (adhesive tape side) Two, 3.1 dia. Reflector (Provided with E3T-SR4@-S) E39-R37-CA Material: Mounting plate: stainless steel (SUS301) Reflective surface: acrylic Note: The reflective plate and mounting plate (1) come as a set.

Accessories (Order Separately) Mutual Interference Prevention Filter for E3T-ST3@/ST1@ Through-beam Sensors E39-E14 Slit for E3T-ST@@ Through-beam Sensors E39-S63 Slit for E3T-FT@@ Through-beam Sensors E39-S64 0.5-dia Slit for E3T-ST@@M Through-beam Sensors E39-S76A 1-dia Slit for E3T-ST@@M Through-beam Sensors E39-S76B Sensitivity Adjustment Unit for E3T-ST1@/ST3@ Through-beam Sensors E39-E10 Tape Reflectors E39-RS1-CA Four, R1 Adhesive tape side 0.5 Material: Acrylic E39-RS3-CA Material: Acrylic 0.5 Four, R1 Adhesive tape side E39-RS2-CA Material: Acrylic 40 0.5 Four, R1 Adhesive tape side Optical axis 7.4 8.1 3 dia. 8.1 9.9 3.8 2.7 918.5 With Filter Attachment Material: 0.2-mm thick stain- less steel (SUS301) Two, 2.2 dia. 2.7 2.7 12.6 9.7 1.0±0.05 dia. 0.5±0.05 dia. 7.4 Notch With Slit Attachment Material: 0.2-mm thick stainless steel (SUS301) Note: Align the notch direction of the Slit when installing on the Emitter and Receiver. 12.3 (4.1) 0.5 dia. 1 dia. With Slit Attachment Material: 0.1-mm thick stain- less steel (SUS301) 0.5±0.05 dia. 7.4 Two, 3.2 × 3.4 12.2 6.5 13.2 10.4 13.2 13.2 Material: 0.2-mm thick stain- less steel (SUS301) With Slit Attachment 1.0±0.1 dia. 7.4 Two, 3.2 × 3.4 12.2 6.5 13.2 13.2 10.4 Material: 0.2-mm thick stainless steel (SUS301) With Slit Attachment 2 dia.Optical axis 90° 7.4 (10.1) (15.1) 18.7 9.7 5.8 Adjuster With Sensitivity Adjustment Unit Attachment Material: stainless steel (SUS301)

7.5(17.8) 4.1 Two, 3.4 1.6 9.5 2.2 31.2 1.2 2.4 90° 20.5 15 24.5 31.2 9.7 (10.3) 17.8 6.2 7.7With Mounting Bracket (Example: E3T -ST11) (Two, R2) (Two, R2) (Two, R1.1) (Two, R1.2) (Two, R1.7) R1.5 max. (Four, R2) Three, M2 Two, M2 × 14 Mounting Bracket for M2-mounting Side-view Sensors E39-L116 Material: 1.2-mm-thick stainless steel (SUS304) 2320.5 15 (10.3) 11.2 7.7 3.1 3.1 18 11.5 11.2 3.4 4.5 Two, R2 90° 2.4 (23) 15 Two, 2.2 (11.2) 10.2 16.3 11.2 6.2 1.2 Two, M2 × 14 (Two, R1.7) (Two, R1.7) R1 max. (Two, R1.1) (Two, R2) (Four, R2) Three, M2 With Mounting Bracket (Example: E3T -ST11) Mounting Bracket for M2-mounting Side-view Sensors E39-L117 Material: 1.2-mm-thick stainless steel (SUS304)

20.5 15 7.7 90° 90° 11.5 11.5 22.7 2.4 Two, 2.2 4.5 3.4 (23)18 11.5 16.3 13.2 3.1 3.1 1.2 (Two, R1.7) (Four, R2)(Two, R1.1) Two, M2 × 14(Four, R2) Three, M2 With Mounting Bracket (Example: E3T -ST11) Mounting Bracket for M2-mounting Side-view Sensors E39-L118 Material: 1.2-mm-thick stainless steel (SUS304) 12 16 90° 9 7 3.2 2.4 2.4 10.5 10.6 97 3.5 1.2 Four, M2 tapped holes Two, M2 × 8 With Mounting Bracket (Example: E3T -FT11) Mounting Bracket for M2-mounting Flat Sensors E39-L119 Material: 1.2-mm-thick stainless steel (SUS304) 12 16 13.56 3.2 2.4 2.4 22.5 4.2 (5.4) 10.6 (6.4) 13.5 1.2 Four, M2 tapped holes Two, M2 × 8 With Mounting Bracket (Example: E3T -FT11) Mounting Bracket for M2-mounting Flat Sensors E39-L120 Material: 1.2-mm-thick stainless steel (SUS304)

3.2 3.2 6.5 2.8 1.2 3.4 4.5

3 Three, M3

13.5 13.5 (12.6) 10 8.5 12.5 (15) 13.8 14.5 13.5 3.1 11.5 3.1 Two, R2 2212.9 90° Two, M3 × 15 With Mounting Bracket (Example: E3T -ST11M) Mounting Bracket for M3-mounting Side-view Sensors E39-L166 Material: 1.2-mm-thick stainless steel (SUS304) Two, M3 × 6 With Mounting Bracket (Example: E3T -FD11M) 3.2 1.5 2.4 17.5 2.4 Four, M3 tapped holes 17 14.5 13.8 17.8 (10.5) (6.5) 23.5 Mounting Bracket for M3-mounting Flat Sensors E39-L167 Material: 1.5-mm-thick stainless steel (SUS304) 40.312.6 8.3 10.8 14.828.7 10 (7.3) Back-mounting Spacer for M3-mounting Flat Sensors E39-L168 Note: Use this Spacer when mounting the Sensor from the back. Material: PBT (polybutylene terephthalate)

READ AND UNDERSTAND THIS DOCUMENT Please read and understand this document befor e using the products. Please c onsult your OMRON representative if you have any qu estions or comments. WARRANTY OMRON’s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY , OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABL Y MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY , NEGLIGENCE, OR STRICT LIABILITY . In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY , REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON’S ANAL YSIS CONFIRMS THAT THE PRODUCTS WERE PROPERL Y HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. SUITABILITY FOR USE THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. THEY ARE NOT DESIGNED OR RATED FOR ENSURING SAFETY OF PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to separate catalogs for OMRON's safety rated products. OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of produc ts in the customer’s application or use of the product. At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exh austive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:  Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document.  Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.  Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERI OUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERL Y RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PERFORMANCE DATA Performance data given in this document is provided as a guide for the user in determ ining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assum ed for clerical, typographical, or proofreading errors, or omissions. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user’s programming of a programmable product, or any consequence thereof. COPYRIGHT AND COPY PERMISSION This document shall not be copied for sales or promotions without permission. This document is protected by copyright and is intended solely for use in conjunction with t he product. Please notify us before copying or reproducing this document in any manner, for any other purpose. If copying or transmitting this document to another, please copy or transmit it in its entirety.

: r o t u b i r t s i D d e z i r o h t u A , t n e m e v o r p m i t c u d o r p f o t s e r e t n i e h t n I . e c i t o n t u o h t i w e g n a h c o t t c e j b u s e r a s n o i t a c i f i c e p s . d e v r e s e R s t h g i R l l A 0 1 0 2 n o i t a r o p r o C N O R M O © n o i t a r o p r o C N O R M O y n a p m o C n o i t a m o t u A l a i r t s u d n I C L L S C I N O R T C E L E N O R M O , g r u b m u a h c S e v i r D e c r e m m o C e n O . A . S . U 2 0 3 5 - 3 7 1 0 6 L I 7 8 7 7 - 3 4 8 - 7 4 8 ) 1 ( : x a F / 0 0 9 7 - 3 4 8 - 7 4 8 ) 1 ( : l e T s r e t r a u q d a e H l a n o i g e R . V . B E P O R U E N O R M O t i n U s s e n i s u B r o s n e S y n a m r e G , n e g n i r f u N 4 5 1 1 7 - D , 4 . r t S - z n e B - l r a C 9 9 1 - 1 1 8 - 2 3 0 7 ) 9 4 ( : x a F / 0 - 1 1 8 - 2 3 0 7 ) 9 4 ( : l e T m o c . n o r m o . a i . w w w : t c a t n o C N A P A J , o y k o T . D T L . E T P C I F I C A P A I S A N O R M O , ) 2 y b b o L ( 8 0 / 5 0 - 5 0 # d a o R a r d n a x e l A A 8 3 4 . o N , k r a p o n h c e T a r d n a x e l A 7 6 9 9 1 1 e r o p a g n i S 1 1 7 2 - 5 3 8 6 ) 5 6 ( : x a F / 1 1 0 3 - 5 3 8 6 ) 5 6 ( : l e T . D T L , . O C ) A N I H C ( N O R M O , r e w o T a n i h C f o k n a B , 1 1 2 2 m o o R , d a o R g n o h Z g n e h C n i Y 0 0 2 a n i h C , 0 2 1 0 0 2 , i a h g n a h S , a e r A w e N g n o D u P 0 0 2 2 - 7 3 0 5 - 1 2 ) 6 8 ( : x a F / 2 2 2 2 - 7 3 0 5 - 1 2 ) 6 8 ( : l e T Printed in Japan (1010)Cat. No. E407-E1-01 CSM_3_1_1210