E2EZ-X2D1-M1GJ0.3M

E2EZ-X4D1-R OMRON | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 9

Technical content

Chip-immune Inductive Proximity Sensor E2EZ Chip-immune Inductive Proximity Sensor

• Correct operation even with aluminum or iron chips sticking to the Sensor. Only the sensing object is detected.  Pre-wired Smartclick Connector Models also available. Be sure to read Safety Precautions on page 7. For the most recent information on models that have been certified for safety standards, refer to your OMRON website.

Ordering Information

Sensors [Refer to Dimensions on page 8.] Pre-wired Models Pre-wired Smartclick Connector Models (M12) Appearance Sensing distance Output configuration Model Operation mode NO NC M12 DC 2-Wire Models E2EZ-X2D1-N 2M E2EZ-X2D2-N 2M M18 DC 3-wire, NPN E2EZ-X4C1 2M — DC 2-wire E2EZ-X4D1-N 2M E2EZ-X4D2-N 2M AC 2-wire E2EZ-X4Y1 2M — M30 DC 3-wire, NPN E2EZ-X8C1 2M — DC 2-wire E2EZ-X8D1-N 2M E2EZ-X8D2-N 2M AC 2-wire E2EZ-X8Y1 2M Shielded 2 mm 4 mm 8 mm Appearance Sensing distance Output configuration Model Operation mode NO NC M12 DC 2-wire, (3)-(4) pin arrangement E2EZ-X2D1-M1TJ 0.3M — DC 2-wire, (1)-(4) pin arrangement E2EZ-X2D1-M1TGJ 0.3M — M18 DC 2-wire, (3)-(4) pin arrangement E2EZ-X4D1-M1TJ 0.3M — DC 2-wire, (1)-(4) pin arrangement E2EZ-X4D1-M1TGJ 0.3M — M30 DC 2-wire, (3)-(4) pin arrangement E2EZ-X8D1-M1TJ 0.3M — DC 2-wire, (1)-(4) pin arrangement E2EZ-X8D1-M1TGJ 0.3M — Shielded 2 mm 4 mm 8 mm

Pre-wired Connector Models (M12) Accessories (Order Separately) Sensor I/O Connectors (M12, Sockets on One Cable End) (Models for Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) [Refer to Dimensions on XS2, XS5.] Mounting Brackets Protective Covers Sputter Protective Covers Refer to Y92@ for details. Appearance Sensing distance Output configuration Model Operation mode NO NC M12 DC 2-wire, (3)-(4) pin arrangement E2EZ-X2D1-M1J 0.3M — DC 2-wire, (1)-(4) pin arrangement E2EZ-X2D1-M1GJ 0.3M — M18 DC 2-wire, (3)-(4) pin arrangement E2EZ-X4D1-M1J 0.3M — DC 2-wire, (1)-(4) pin arrangement E2EZ-X4D1-M1GJ 0.3M — M30 DC 2-wire, (3)-(4) pin arrangement E2EZ-X8D1-M1J 0.3M — DC 2-wire, (1)-(4) pin arrangement E2EZ-X8D1-M1GJ 0.3M — Shielded 2 mm 4 mm 8 mm Appearance Cable length Sensor I/O Connector model number Applicable Proximity Sensor model number 2 m XS2F-D421-DD0 E2EZ-X@D1-M1J5 m XS2F-D421-GD0 2 m XS2F-D422-DD0 5 m XS2F-D422-GD0 2 m XS2F-D421-DA0-F E2EZ-X@D1-M1GJ5 m XS2F-D421-GA0-F 2 m XS2F-D422-DA0-F 5 m XS2F-D422-GA0-F 2 m XS5F-D421-D80-F E2EZ-X@D1-M1TJ E2EZ-X@D1-M1TGJ5 m XS5F-D421-G80-F Straight L-shape Straight L-shape Smartclick Connector Straight

Ratings and Specifications *1. Use the Sensor within the range in which the green indicator is ON. *2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. Model E2EZ-X2D@-N E2EZ-X2D@-M1J E2EZ-X2D@-M1GJ E2EZ-X4D@-N E2EZ-X4D@-M1J E2EZ-X4D@-M1GJ E2EZ-X8D@-N E2EZ-X8D@-M1J E2EZ-X8D@-M1GJ E2EZ-X4C1 E2EZ-X4Y1 E2EZ-X8C1 E2EZ-X8Y1 Item Sensing distance 2 mm ±10% 4 mm ±10% 8 mm ±10% 4 mm ±10% 8 mm ±10% Differential travel 20% max. of sensing distance Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.) Standard sensing object Iron, 12 × 12 × 1 mm Iron, 30 × 30 × 1 mm Iron, 54 × 54 × 1 mm Iron, 30 × 30 × 1 mm Iron, 54 × 54 × 1 mm Response frequency *2 200 Hz 100 Hz 30 Hz C Models: 12 Hz Y Models: 5 Hz C Models: 8 Hz Y Models: 5 Hz Power supply volt- age (operating voltage range) 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. C Models: 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. Y Models: 100 to 220 VAC (90 to 250 VAC), 50/60 Hz Current consumption --- C Models: 15 mA max. Leakage current 0.8 mA max. Y Models: 2 mA max. at 100 VAC, 3 mA max. at 200 VAC Con- trol output Load cur- rent 3 to 100 mA max. C Models: NPN open-collector output 100 mA max. at 12 VDC (30 VDC max.) 200 mA max. at 24 VDC (30 VDC max.) Y Models: 10 to 200 mA Residual voltage 3 V max. (Load current: 100 mA, Cable length: 2 m) C Models: 2 V max. (Load current: 200 mA, Cable length: 2 m) Y Models: Refer to residual voltage characteristic data Refer to page 4. Indicators D1 Models: Operation indicator (red), Setting indicator (green) D2 Models: Operation indicator (red) C Models: Detection indicator (red) Y Models: Operation indicator (red) Operation mode (with sensing ob- ject approaching) D1 Models: NO D2 Models: NC For details, refer to the Timing chart on page 5. NO For details, refer to the Timing chart on page 6. Protection circuits Load short-circuit protection, Surge suppressor C Models: Load short-circuit protection, Reverse polarity protection, Surge suppressor Y Models: Surge suppressor Ambient temperature range Operating/Storage: 0 to 50°C (with no icing or condensation) Ambient humidity range Operating/Storage: 35% to 95% (with no condensation) Temperature influence ±20% max. of sensing distance at 23°C in the temperature range of 0 to 50°C Voltage influence ±2.5% max. of sensing distance at rated voltage in the rated voltage ±10% range Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case C Models: 1,000 VAC, 50/60 Hz for 1 min between cur- rent-carrying parts and case Y Models: 2,000 VAC, 50/60 Hz for 1 min between cur- rent-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions Degree of protection IEC 60529 IP67, in-house standards: oil-resistant Connection method Pre-wired Models (Standard cable length: 2 m) and Pre-wired Connector Models Weight (packed state) E2EZ-X2D@-N: Approx. 70 g E2EZ-X2D@-M1J: Approx. 40 g E2EZ-X2D@-M1GJ: Approx. 40 g E2EZ-X4D@-N: Approx. 160 g E2EZ-X4D@-M1J: Approx. 90 g E2EZ-X4D@-M1GJ: Approx. 90 g E2EZ-X8D@-N: Approx. 220 g E2EZ-X8D@-M1J: Approx. 160 g E2EZ-X8D@-M1GJ: Approx. 160 g Approx. 170 g Approx. 270 g Materi- als Case Nickel-plated brass Sensing surface PBT Heat-resistant ABS Clamp- ing nuts Zinc-plated iron Toothed washer Zinc-plated iron Accessories Instruction manual

Engineering Data (Reference Value) Sensing Area E2EZ-X2@ E2EZ-X4@ E2EZ-X8@ Influence of Sensing Object Size and Material E2EZ-X2@ E2EZ-X4@ E2EZ-X8@ Residual Output Voltage E2EZ-X@D@-N E2EZ-X4Y1/-X8Y1 at 100 VAC E2EZ-X4Y1/-X8Y1 at 200 VAC 0.5 1.0 1.5 Y X 2.0 2.5 8 6 4 2 0−2−4−6−8 0.0 Distance Y (mm)Sensing Head Distance X (mm) Y X 10 8 6 4 2 0 Distance Y (mm)Sensing Head Distance X (mm) −8−12−16−20 X Y 20 16 12 8 4 0−4 Distance Y (mm)Sensing Head Distance X (mm) X 40302010 Side length of sensing object: d (mm) Brass Iron Aluminum Stainless steel (SUS304) Distance X (mm) d × d t = 1 mm X 60 5040 30 20 10 d × d t = 1 mm Side length of sensing object: d (mm) Brass Iron Aluminum Stainless steel (SUS304) Copper Distance X (mm) 01 0 X 60 5040 30 20 d × d t = 1 mm Side length of sensing object: d (mm) Iron Brass AluminumCopper Stainless steel (SUS304) Distance X (mm) 10 5 3 1 1,000 500 300100 50 30 Load current (mA) Residual output voltage (V) 50 A V ON

100 VAC

Load voltage (V) Load current (mA) ON

200 VAC

V A 100 150 200 10 5 200 150 100 50 OFF Residual output voltage Residual load voltage Load voltage (V) Load current (mA)

E2EZ-X4Y1/-X8Y1 E2EZ-X @D@-N Opera- tion mode Model Timing chart Output circuit NO E2EZ-X2D1-N E2EZ-X4D1-N E2EZ-X8D1-N E2EZ-X2D1-M1J E2EZ-X2D1-M1GJ E2EZ-X4D1-M1J E2EZ-X4D1-M1GJ E2EZ-X8D1-M1J E2EZ-X8D1-M1GJ NC E2EZ-X2D2-N E2EZ-X4D2-N E2EZ-X8D2-N 6 A 250200150100 90 AC power Power supply voltage (V) Leakage current (mA) Protective resistance 02 010 0.5 1.0 1.5 4030 Power supply voltage (V) Leakage current (mA) 080(TYP)100(%) Sensing object Rated sensing distance Stable sensing area Non-sensing area Unstable sensing area Set position ON OFF ON OFF ON OFF Setting indicator (green) Operation indicator (red) Control output 0 V Load Brown Blue Prox- imity Sensor main circuit Note: The load can be connected to either the +V or 0 V side. (M1J) 0 V 0 V Load Prox- imity Sensor main circuit Note: The load can be connected to either the +V or 0 V side. Load Prox- imity Sensor main circuit Note: The load can be connected to either the +V or 0 V side. Connector Pin Arrangement Note: Pins 1 and 2 are not used. Connector Pin Arrangement Note: Pins 2 and 3 are not used. (M1GJ) 0100(%) Sensing object Rated sensing distance Sensing areaNon-sensing area ON OFF ON OFF Operation indicator (Red) Control output 0 V Load Brown Blue Prox- imity Sensor main circuit Note: The load can be connected to either the +V or 0 V side.

Connections for Sensor I/O Connectors Operation mode Model Timing chart Output circuit NO E2EZ-X4C1 E2EZ-X8C1 Operation mode Model Timing chart Output circuit NO E2EZ-X4Y1 E2EZ-X8Y1 Present Not present Operate Reset ON OFF Sensing object Load Detection indicator (red) 2.2 Ω 0 V Proximity Sensor main circuit Load Brown Black Output Blue * 100 mA max. at 12 V, 200 mA max. at 24 V (load current). Present Not present Operate Reset ON OFF Sensing object Load Operation indicator (red) LoadBrown Blue Prox- imity Sensor main circuit Proximity Sensor Sensor I/O Connectors ConnectionsModel Operation mode Model Model DC 2-Wire Models (IEC pin wiring) NO E2EZ-X@D1-M1GJ DC 2-Wire Models (previous pin wir- ing) E2EZ-X@D1-M1J DC 2-Wire Models (IEC pin wiring) E2EZ-X@D1-M1TGJ DC 2-Wire Models (previous pin wir- ing) E2EZ-X@D1-M1TJ XS2F-D42@-@A0-F 1: Straight 2: L-shape D: 2-m cable G: 5-m cable XS2F E2EZ main circuit Brown (+) Blue (−) XS2F-D42@-@D0 1: Straight 2: L-shape D: 2-m cable G: 5-m cable XS2F E2EZ main circuit Blue (−) Brown (+) XS5F-D421-@80-F D: 2-m cable G: 5-m cable XS5F E2EZ main circuit Brown (+) White Blue Black (−) XS5F E2EZ main circuit Blue (−) Black (+) Brown White Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details.

Refer to Warranty and Limitations of Liability. This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Do not use this product under ambient conditions that exceed the ratings.

• Design Influence of Surrounding Metal When mounting the Sensor within a metal panel, ensure that the clearances given in the following table are maintained. Failure to maintain these distances may cause deterioration in the performance of the Sensor. Influence of Surrounding Metal (Unit: mm) Mutual Interference When installing Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained. Aluminum and Iron Cuttings Normally aluminum or iron cuttings will not be detected even if they adhere to or accumulate on the sensing surface. Detection signals may be output for the following: If this occurs, remove the cuttings from the sensing surface. 1. Relationship between the Size of the Cutting (d) and the Size of the Sensing Surface (D) Cuttings of the size d ≥ D on the sensing surface *
• Mounting Do not tighten the nut with excessive force. A washer must be used with the nut.Note: 1. The allowable tightening strength depends on the distance from the edge of the head, as shown in the following table. (A is the distance from the edge of the head. B includes the nut on the head side. If the edge of the nut is in part A, the tightening torque for part A applies instead.) 2. The following torque assume washers are being used. WARNING Precautions for Correct Use Item l d D m n Model Embedded material E2EZ-X2@ Iron 01 20 8 18 Aluminum 22 52 3 6 E2EZ-X4@ Iron 01 80 16 27 Aluminum 54 05 5 4 E2EZ-X8@ Iron 03 00 32 45 Aluminum 10 70 10 90 D d dia. m n l Mutual Interference (Unit: mm) Model Item A B E2EZ-X2@ 30 20 E2EZ-X4@ 40 50 E2EZ-X8@ 60 100 A B Tightening Torque Part A Part B Model Dimension (mm) Torque Torque E2EZ-X2D@-@ 30 N·m E2EZ-X4D@-@ 70 N·m E2EZ-X8D@-@ 180 N·m E2EZ-X4C1 E2EZ-X4Y1 20 15 N·m 29 N·m E2EZ-X8C1 E2EZ-X8Y1 22 29 N·m 39 N·m D d Sensing surface Cutting Cutting Pressed against sensing surface. Cuttings of the size d* (Unit: mm) *E 2 E Z - X 2@: d ≥ D on the sensing surface. 2. Cuttings Pressed against the Sensing Surface Model Size D E2EZ-X2@ 10 * E2EZ-X4@ 16 E2EZ-X8@ 28 Part B Part A

(Unit: mm) Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified. 38 9 17 4 21 dia. M12 × 1 15 dia. M12 × 1 Indicator*2 Two clamping nuts Toothed washer *1. 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm 2, Insulator diameter: 1.3 mm), Standard length: 2 m *2. D1 Models: Operation indicator (red), Setting indicator (green), D2 Models: Operation indicator (red) Pre-wired Connector Models (-M1J/M1GJ) 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm 2, Insulator diameter: 1.3 mm), Standard length: 300 mm E2EZ-X2D@-N 15 dia. M12 × 1 Pre-wired Connector Models (-M1J/M1GJ) 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm 2, Insulator diameter: 1.9 mm), Standard length: 300 mm E2EZ-X4D@-N 43 12 424 29 dia. M18 × 1 Indicator*2 Two clamping nuts Toothed washer *1. 6-dia. vinyl-insulated round cable with 2 conduc- tors (Conductor cross section: 0.5 mm2, Insula- tor diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (sepa- rate metal conduit). *2. D1 Models: Operation indicator (red), Setting in- dicator (green) D2 Models: Operation indicator (red) 48 12 536 42 dia. M30 × 1.5 Indicator*2 Two clamping nuts Toothed washer *1. 6-dia. vinyl-insulated round cable with 2 con- ductors (Conductor cross section: 0.5 mm2, In- sulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (sepa- rate metal conduit). *2. D1 Models: Operation indicator (red), Setting indicator (green) D2 Models: Operation indicator (red)15 dia. M12 × 1 Pre-wired Connector Models (-M1J/M1GJ) 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm 2, Insulator diameter: 1.9 mm), Standard length: 300 mm E2EZ-X8D@-N E2EZ-X4C1 E2EZ-X4Y1 6024 29 dia. M18 × 1 4 4Two toothed washers Two clamping nuts Indicator*2 *2. C Models: Detection indicator (red), Y Models: Operation indicator (red) *1. C Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m E2EZ-X8C1 E2EZ-X8Y1 6036 42 dia. M30 × 1.5 Two toothed washers Two clamping nuts Indicator*2 *2. C Models: Detection indicator (red), Y Models: Operation indicator (red) *1. C Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m Model F (mm) E2EZ-X2@ 12.5 dia. E2EZ-X4@ 18.5 dia. E2EZ-X8@ 30.5 dia. +0.5 +0.5 +0.5 F

Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2014.1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2014 All Right Reserved.