DTR-622-SM-LC-A-HP-ST OPLINK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

/boxcheckbld Designed for Multi-rate OC-3 (155Mb/s) & OC-12 (622Mb/s) data rates /boxcheckbld Long Reach 1310nm (40km distance) and 1550nm (80km) as well as Intermediate Reach (15km) /boxcheckbld Eye Safe (Class I Laser Safety) /boxcheckbld Multi-sourced 10-pin (2x5) SFF (Small Form Factor) package style /boxcheckbld Duplex LC optical connector interface /boxcheckbld Excellent EMI & ESD protection /boxcheckbld Single +3.3V power supply & LV-PECL DATA interface /boxcheckbld Option for LV-TTL or LV-PECL SIGNAL DETECT output The DTR-622-SM-LC-MR and DTR-622-SM-LS-MR fiber optic transceivers offer a simple, convenient way to interface PCBs to single mode fiber optic cables. These multi-rate transceivers are designed with performance versions that are fully compliant with SONET/SDH standards for OC-12/STM-4 data rate for Short Reach (12/2 km), Intermediate Reach (21/15 km) and Long Reach (42/40 km and 85/80 km) specifications. The modules also operate down to OC-3/STM-1 data rate. All modules satisfy Class I Laser Safety requirements in accordance with the US FDA/CDRH and international IEC-825 standards. The transmit and receive functions are contained in a narrow width two-row, 10-pin (2x5) package with a Duplex LC connector interface. The receptacle fits into an RJ-45 form factor outline. The 10-pin configuration is in conformance to a Small Form Factor (SFF) multisource transceiver agreement. The transmitter incorporates a highly reliable 1300 nm or 1550 nm InGaAsP Laser and a driver circuit which converts LV-PECL data to light. A LV-TTL Transmitter Disable control input is also provided. The receiver features a transimpedance amplifier IC with internal AGC for high sensitivity and wide dynamic range. The Signal Detect status output can be either LV-TTL or LV-PECL. The transceiver operates from a single +3.3V power supply over an operating temperature range of - 5°C to +70°C or - 40°C to +85°C (“A” option). The package is made of metal for excellent EMI shielding

Description

Optical Communication Products, Inc. Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units StorageT emperature Tst -40 +85 °C OperatingCase T emperature "A"option Top -40 +85 "B"option -5 +70 SupplyVoltage VCC 0+ 6 . 0V InputVoltage Vin 0 VCC V OutputCurrent IO -5 0 m A LeadSolderingT emperature&T ime - - 260°C,10sec OCP

2 21737-0375, Rev. B 06-12-2003 Transmitter Performance Characteristics (over Operating Case Temperature) Receiver Performance Characteristics (over Operating Case Temperature) OC-12/STM-4 LC Single Mode Transceiver: DTR-622-SM-LC/LS-MR Parameter Symbol Minimum Typical Maximum Units DataRate B 155 622 700 Mb/s ReceiverSensitivity(10 -10BER)1,2 Pmin -28.0 -31.0 - dBm MaximumInputOpticalPower(10 -10BER)1 Pmax -7.0 0 - dBm SignalDetect Thresholds IncreasingLightInput Psd+ - - -28.0 dBm DecreasingLightInput Psd- -45.0 - - SignalDetectHysteresis - 0.5 1.5 - dB SignalDetectT iming Delay IncreasingLightInput tsd+ -- 1 0 0 µs DecreasingLightInput tsd- -- 1 0 0 WavelengthofOperation λ 1100 - 1600 nm 1SpecifiedinAverageOpticalInputPowerandmeasuredat155Mb/s&622Mb/sand1300nm(1550nmforLR2)wavelengthwith2231PRBS. 2ForLongReach(LR1&LR2),themodulesarenotfullycompliantwithSO N ETO C- 3/STM- 1specificationsforsensitivity. Laser Safety: All transmitters are Class I Laser products per FDA/CDRH and IEC-825 standards. They must be operated under specified operating conditions. Optical Communication Products, Inc. DATE OF MANUFACTURE: MANUFACTURED IN THE USA This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements Parameter Symbol Minimum Typical Maximum Units DataRate B 155 622 700 Mb/s AverageOpticalOutputPower (coupledintosinglemode fiber),50%dutycycle HP1 Po -3.0 -1.0 +2.0 dBm ExtinctionRatio SR&IR Phi/Plo 8.2 - - dBLR1&LR2 10 - - CenterWavelength2 SR(ShortReach) λc 1261 1310 1360 nmIR(IntermediateReach) 1274 1310 1356 1293 1310 1334 LR1(LongReach1310nm) 1280 1310 1335 LR2(LongReach1550nm) 1480 1550 1580 SpectralWidth(RMS)

2 SR(ShortReach) ∆λRMS

-- 4 . 0 nmIR(IntermediateReach) - - 2.5or4.0 1 SpectralWidth(-20dB) LR1&LR2 ∆λ20 -- 1 . 0 SideModeSuppressionRatio LR1&LR2 SMSR 30 - - dB OpticalOutputEye CompliantwithT elcordiaGR-253-COREandITU-TRecommendationG .957 1ForLongReachV ersion(LR1&LR2),themodulesarenotfullycompliantwithSONETOC-3/STM-1specificationsforoutputpower. 2ForIntermediateReachversion,theCenterWavelengthiseither1274nm≤ λc ≤1356nmfor∆λRMS≤2.5nm or1293nm≤ λc ≤1334nmfor∆λRMS≤4.0nm.

3 21737-0375, Rev. B 06-12-2003 Transmitter Electrical Interface (over Operating Case Temperature Range) Receiver Electrical Interface (over Operating Case Temperature Range) Electrical Power Supply Characteristics (over Operating Case Temperature Range) Parameter Symbol Minimum Typical Maximum Units SupplyVoltage VCC 3.13 3.3 3.47 V SupplyCurrent1 TX ICC,TX - 80 120 mA RX ICC,RX - 70 100 1Supplycurrentdoesnotincludeterminationresistorcurrent. Parameter Symbol Minimum Typical Maximum Units OutputHIGHVoltage(LV-PECL)1 VOH VCC-1.10 - VCC-0.90 V OutputLOWVoltage(LV-PECL)1 VOL VCC-1.84 - VCC-1.60 V OutputHIGHVoltage(LV-TTL) VOH 2.4 - VCC OutputLOWVoltage(LV-TTL) VOL 0- 0 . 8 OutputCurrent IO -- 2 5 m A 1With50ΩterminatedtoVCC-2volts. Parameter Symbol Minimum Typical Maximum Units InputHIGHVoltage VIH VCC-1.165 - VCC-0.700 V InputLOWVoltage VIL VCC-1.950 - VCC-1.475 V TransmitterDisableVoltage VDIS VCC-1.3 - VCC V TransmitterEnableVoltage VEN 0- 0 . 8 V OC-12/STM-4 LC Single Mode Transceiver: DTR-622-SM-LC/LS-MR Pin Assignments PIN FUNCTION LOGICFAMILY 1R X G N D - 2V CCRX -

3 SD(RXSIGNALDETECT) LV-TTL/LV-PECL

4 RD-(RXDATAOUT-) LV-PECL

5 RD+(RXDATAOUT+) LV-PECL

8 TXDISABLE LV-TTL

9 TD+(TXDATAIN+) LV-PECL

10 TD-(TXDATAIN-) LV-PECL

4 21737-0375, Rev. B 06-12-2003 +3.3volt

1 Hcoilor

µ µ TXD+ TXD- SIGNALDETECT TXDISABLE RXD- RXD+ GND POSTS 0.1 0.1 10 0.1 160 160 160 100 Capacitorvaluesin F,Resistorvaluesinohmµ 50ohmline LV-PECL50ohmline 100 50ohmline 50ohmline LV-PECL 160 DTR-622-SM-LC-MR OC-12/STM-4 LC Single Mode Transceiver: DTR-622-SM-LC/LS-MR Internal Termination (for “M” & “ME” version) Transmitter: When the DA TA+ input is at logic HIGH and DA TA- input is at logic LOW, the Laser Diode is ON; and vice versa. The transmitter is normally enabled (i.e. when the TX DISABLE control input is not connected). When the TX DISABLE control input voltage is higher than V CC - 1.3 V , the laser is turned off independent of the input data. The transmitter has two options for input termination. With “MS” and “MSE” versions, the transmitter input interface is standard LV-PECL(i.e. normal resistor termination needs to be provided by the end user). With the “M” and “ME” version, an internal differential 100 ohm resistor termination is provided at the transmitter input interface for convenience (see circuit diagrams below.) The transmitter incorporates an Average Power Control (APC) loop to stabilize the transmitter average optical output power against temperature variation. The APC loop always acts to keep the transmitter average optical output power at a constant value. Therefore, when the input data is all continuous “zeroes” or all continuous “ones”, the transmitter optical output power is a constant level equal to the nominal average optical output power (not at the “OFF” level or at the “ON” level). Application Notes Receiver: Both differential DATA+ and DA TA- outputs are LV- PECL levels requiring proper termination (see recommended interface circuits). For optimum performance, both outputs should be terminated in the same manner, even if only one is used. The Signal Detect circuit monitors the level of the incoming optical signal and generates a logic LOW signal when insufficient photocurrent is produced. If the SIGNAL DETECT output is LV-TTL level, no termination is required. If the SIGNAL DETECT output is LV-PECL level, a termination resistor of 160 ohms to GND is required. Interface circuit: The power supply line should be well-filtered. All 0.1 µF power supply bypass capacitors should be as close to the DTR transceiver module as possible. The two front GND posts (mounting studs) should be grounded to Circuit Ground or Chassis Ground. The Transmitter has internal 50 ohm termination (see interface circuits).

5 21737-0375, Rev. B 06-12-2003 OC-12/STM-4 LC Single Mode Transceiver: DTR-622-SM-LC/LS-MR Package without EMI shield (LC) +3.3volt µ µ TXD+ TXD- SIGNALDETECT TXDISABLE RXD- RXD+ GND POSTS 0.1 0.1 10 0.1 160 160 160 100 Capacitorvaluesin F,Resistorvaluesinohmµ 50ohmline LV-PECL50ohmline 50ohmline 50ohmline LV-PECL 160 100 DTR-622-SM-LC-MR External Termination (for “MS” & “MSE” version) Notes: 1. Default tolerance for all dimensions given in inches [mm] .xxx = +0.005” .xx = +0.01” 2. x, y: see Pin length option table in ordering information

6 21737-0375, Rev. B 06-12-2003 Package with EMI Shield (LS) OC-12/STM-4 LC Single Mode Transceiver: DTR-622-SM-LC/LS-MR 11.9 .47 3.6 .14 [9.78 MAX] .385 MAX (Y) 9.65 .380 0.38 .015 TYP (X) 15.01 .59 48.44 1.907 [13.59 MAX] .535 MAX 15.11 .60 RX TX 15.6 .62 0.76 .030 1.91 .075 2.54 .1002X 1.02 .040 10.16 .400 0.46 .018 TYP 18.54 .730 [13.59 +0/-0.254] .535 +0/-.01 17.78 .700 1.78 .070 TYP PIN 1PIN 5 PIN 6 6.25 .246 Package with Extended EMI Shield (S1) Notes: 1. Default tolerance for all dimensions given in inches [mm] .xxx = +0.005” .xx = +0.01” 2. x, y: see Pin length option table in ordering information Notes: 1. Default tolerance for all dimensions given in inches [mm] .xxx = +0.005” .xx = +0.01” 2. x, y: see Pin length option table in ordering information

7 21737-0375, Rev. B 06-12-2003 Optical Communication Products, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Optical Communication Products, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Optical Communication Products, Inc. for its use nor for any infringements of third parties which may result from its use. No license is granted by implication or otherwise under any patent right of Optical Communication Products, Inc. Optical Communication Products, Inc. 20961 Knapp Street, Chatsworth, CA 91311, Tel.: 818-701-0164, FAX: 818-701-1468, http://www.ocp-inc.com OC-12/STM-4 LC Single Mode Transceiver: DTR-622-SM-LC/LS-MR Distance Option1 specifies the range for Center Wavelength & Spectral Width to be compliant with SONET/SDH standard SR : SR-1 / I-4 distance 12/2 km IR : IR-1 / S-4.1 ” 21/15 km2 LR1 : LR-1 / L-4.1 ” 42/40 km3 LR2 : LR-2 / L-4.2 ” 85/80 km4

Ordering Information

DTR - 622 - SM - Lx -T- Ln - D - Mpxy - MR - S1 Temperature Range “Blank” : - 5°C to +70 °C 1These are target distances to be used for classification and not for specification, per Telcordia GR-253-CORE/ITU-T Recommendation G.957 2The DTR-622-SM-Lx-T-L3-IR-Mpxy-MR modules are fully compliant with OC-12/STM-4 Intermediate Reach IR-1/S-4.1 SONET/SDH standard for distance of 21/15 km. 3The DTR-622-SM-Lx-T-HP-LR1-Mpxy-MR are fully compliant with OC-12/STM-4 Long Reach 1310 nm LR1/L-4.1 SONET/SDH standard. They use DFB lasers to satisfy the requirement for Center Wavelength & Spectral Width. 4The DTR-622-SM-Lx-T-HP-LR2-Mpxy-MR are fully compliant with OC-12/STM-4 Long Reach 1550 nm LR-2/L-4.2 SONET/SDH standard. Both modules use DFB lasers. However, the DTR-622-SM-Lx-A-HP-LR2-Mpxy-MR is specified only over -25°C to +70°C. Light Output Option HP: (- 3 dBm to +2 dBm) for LR1 or LR2 option L3: (- 15 dBm to - 8.0 dBm) for SR or IR option Connector LC : w/o EMI Shield LS : w/ EMI Shield see Pin Length Option Table Pin Length Option Table Options (P) PinLength(x) PostLength(y) Inches Millimeters Inches Millimeters -0.005 3.17+0.250 -0.125 -0.005 3.94+0.250 -0.125 Transmitter Termination “Blank” : Internal “S” : External Signal Detect Option “Blank” : LV-TTL “E” : LV-PECL Extended Shield Option “Blank” : NONE “S1”: Extended EMI shield