DT0703 MACOM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Series Number 3003 9th Avenue SW PO Box 50 DT0703 Watertown, SD 57201 DT1351 Toll free: 888-978-2638 Ph: 605-886-3326 Fax: 605-886-8995 Number L W H Y Z A B C L1 Suffix DCR2 IAVE

3 Storage Tolerance DCR2 IAVE

3 Storage Tolerance Dot Code

µH Codes W A mJ Suffix4 W A mJ Suffix4 1st 2nd 3rd 1) Tested at 100kHz, 100mVrms @20°C. 2) DCRs (DC resistances) are maximums @20°C. 3) Average maximum allowable current. Spikes as high as 2X the current rating. 4) Tolerance of M = ±20%. Call Toll Free: 888-978-2638 Website: www.coev.net Significant DigitDT0703 DT1351 Shielded, High Current, Inductors Smart Part Numbers: ( Series Number ) - ( Suffix Code )(Tolerance), example DT6630-100M Bulk Packaging add (-B) to end of Part Numbering Sequence. example DT6630-100M-B DT0703 DT1351 Series Maximum Dimensions Reference Dimensions B A C B Suggested Land Pattern Features: High energy storage and low resistance. Ideal for DC-DC buck or boost conversion. Reliable surface mounting. Low temperature rise over inductance range. H Y W L Z 1st significant digit 3rd significant digit 2nd significant digit Parts will be marked with Significant Digit Dots OR Suffix code Specifications subject to change without notice

B Revision Sheet 2 of 3 90-0059 Reel Quantity 90-0057 Reel dimensions (mm) Customer Packaging Specifications For Print Distribution to Customers 2500 700 Series DT SERIES A B C D E A A SECTION A-A T f1.5+1.0 U F W 4.0±0.1 V PACKAGING NOTE: Only pressure sensitive cover tape is to be used. Dimensions are in millimeters unless specified.

Item Specification Test Method/Condition Environmental Static Humidity After exposure part remains within specified electrical parameters for L, Q and DCR. Storage Life After exposure part remains within specified electrical parameters for L, Q and DCR. Moisture Resistance After exposure, part shall not Per MIL-STD 202 Method 106, ten 24 hour cycles at +25°C to have a shorted or open winding. +65°C at 80 to 95% R.H. During any of the first 9 cycles, inductors are revolved from the chamber and exposed to -10°C for 3 hours. Allow parts to dry for 2 hours before measurements are taken. Temperature Cycle After exposure part remains 10 cycles (Air to Air) 1 cycle shall consist of: within specified electrical 30 minutes exposure to +85°C parameters for L, Q and DCR. 30 minutes exposure to -40°C Allow 20 minutes transition between extremes. Temperature Shock After exposure part remains 10 cycles (Air to Air) 1 cycle shall consist of: within specified electrical 30 minutes exposure to -45°C parameters for L, Q and DCR. 30 minutes exposure to +125°C 15 seconds maximum transition between temperatures General Storage Temperature Range -40°C to +85°C Operating Temperature Range -40°C to +85°C Flammability IEC 695-2-2 Withstands needle-flame test Other Vibration After exposure part remains Inductors shall be randomly vibrated per NAVMAT P9492 within specified electrical profile. Samples shall be subjected to 0.04G/Hz for a parameters for L, Q and DCR. minimum of 15 minutes per axis, for each of the three axes. Mechanical Shock After exposure part remains Test per MIL-STD 202 method 213 test condition A, test within specified electrical mounted samples 3 axes, 6 times, totaling 18 shocks. parameters for L, Q and DCR. (50Gs, 11ms, half-sine). Solderability Wetting shall cover 90% minimum of each termination Component Adhesion (Push Test) 4 pounds Apply and measure force with a digital force gauge set. Resistance to Solvent No sign of degradation in Withstands 6 minutes of alcohol. appearance or marking detail. Withstands 3 minutes forced spray Freon TMS Load Life After exposure, part shall not Parts to be stored at 110°C for 1000 hours with rated current have a shorted or open winding. applied. Parts to be tested at: start, 500 and 1000 hours. Allow 2 hours at room temperature before testing. Series Revision Sheet 3 of 3 Subject parts to an environment of +50°C 90 to 100% R.H. for 46 to 50 hours. After exposure, allow parts to dry for 2 hours before measurements are taken. Expose parts to an environment of +50°C with 90 to 95% R.H. for 100 hours. After exposure, allow parts to dry for 2 hours before measurements are taken. DT SERIES BFor Print Distribution to Customers Dip pads in RMA flux, 63/37 solder (Sn/Pb) at 232°C for 5 seconds ±2 seconds.