DS92LV1021 NSC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 18
Technical content
Features
n Guaranteed transition every data transfer cycle n Single differential pair eliminates multi-channel skew n Flow-through pinout for easy PCB layout n 400 Mbps serial Bus LVDS bandwidth (at 40 MHz clock) n 10-bit parallel interface for 1 byte data plus 2 control bits n Synchronization mode and LOCK indicator n Programmable edge trigger on clock n High impedance on receiver inputs when power is off n Bus LVDS serial output rated for 27 Ω load n Small 28-lead SSOP package-MSA Block Diagrams 10011001 TRI-STATE® is a registered trademark of National Semiconductor Corporation. December 2002 DS92LV1021 and DS92LV1210 16-40 MHz 10 Bit Bus LVDS Serializer and Deserializer © 2002 National Semiconductor Corporation DS100110 www.national.com
Block Diagrams (Continued) Application 10011002 Functional Description The DS92LV1021 and DS92LV1210 is a 10-bit Serializer / Deserializer chipset designed to transmit data over a heavily loaded differential backplanes at clock speeds from 16 to 40MHz. It may also be used to drive data over Unshielded Twisted Pair (UTP) cable. The chipset has three active states of operation: Initializa- tion, Data Transfer, and Resynchronization; and two passive states: Powerdown and TRI-STATE The following sections describe each operation and passive state. Initialization Before data can be transferred both devices must be initial- ized. Initialization refers to synchronization of the Serializer and the Deserializer PLL’s to local clocks that may be the same or separate. Afterward, synchronization of Deserializer to Serializer occurs as the second step of initialization. Step 1: When V CC is applied to both Serializer and/or Dese- rializer, the respective outputs are held in TRI-STATE ® and internal circuitry is disabled by on-chip power-on circuitry. When V CC reaches VCC OK (2.5V) the PLL in each device begins locking to a local clock. For the Serializer, the local clock is the transmit clock, TCLK, provided by the source ASIC or other device. For the Deserializer, the local clock is provided by an on-board oscillator or other source and ap- plied to the REFCLK pin. After V CC OK is reached the device’s PLL will lock. The Serializer outputs are held in TRI-STATE while the PLL locks to the TCLK. The Serializer is now ready to send data or SYNC patterns depending on the levels of the SYNC1 and SYNC2 inputs. The SYNC pattern is composed of six ones and six zeros switching at the input clock rate. The Deserializer LOCK output will remain high while its PLL is locking to the local clock- the REFCLK input and then to SYNC patterns on the input. Step 2: The Deserializer PLL must synchronize to the Seri- alizer to complete the initialization. The transmission of SYNC patterns to the Deserializer enables the Deserializer to lock to the Serializer signal. Control of the sync pins is left to the user. A feedback loop between the LOCK pin is one recommendation. Another option is that one or both of the Serializer SYNC inputs are asserted for at least 1024 cycles of TCLK to initiate trans- mission of SYNC patterns. The Serializer will continue to send SYNC patterns after the minimum of 1024 if either of the SYNC inputs remain high. When the Deserializer detects edge transitions at the Bus LVDS input it will attempt to lock to the embedded clock information. When the Deserializer locks to the Bus LVDS clock, the LOCK output will go low. When LOCK is low the Deserializer outputs represent incoming Bus LVDS data. Data Transfer After initialization, the Serializer inputs DIN0–DIN9 may be used to input data to the Serializer. Data is clocked into the Serializer by the TCLK input. The edge of TCLK used to strobe in data is selectable via the TCLK_R/F pin. TCLK_R/F high selects the rising edge for clocking data and low selects the falling edge. If either of the SYNC inputs is high for 5*TCLK cycles the data at DIN 0-DIN9 is ignored regardless of the clock edge. A start bit and a stop bit, appended internally, frame the data bits in the register. The start bit is always high and the stop bit is always low. The start and stop bits function as the embedded clock bits in the serial stream. Serialized data and clock bits (10+2 bits) are transmitted from the serial data output (DO) at 12 times the TCLK frequency. For example, if TCLK is 40 MHz, the serial rate is 40 x 12 = 480 Mega bits per second. Since only 10 bits are from input data, the serial “payload” rate is 10 times the TCLK frequency. For instance, if TCLK = 40 MHz, the pay- load data rate is 40 x 10 = 400 Mbps. TCLK is provided by the data source and must be in the range 16 MHz to 40 MHz nominal. The outputs (DO ±) can drive a heavily loaded backplane or a point-to-point connection. The outputs transmit data when the enable pin (DEN) is high, PWRDN = high and SYNC1 and SYNC2 are low. The DEN pin may be used to TRI- STATE the outputs when driven low. The LOCK pin on the Deserializer is driven low when it is synchronized with the Serializer. The Deserializer locks to DS92LV1021 and DS92LV1210 www.national.com 2
Data Transfer (Continued) the embedded clock and uses it to recover the serialized data. ROUT data is valid when LOCK is low. Otherwise ROUT0–ROUT9 is invalid. RCLK pin is the reference to data on the ROUT0-ROUT9 pins. The polarity of the RCLK edge is controlled by the RCLK_R/F input. ROUT(0-9), LOCK and RCLK outputs will drive a minimum of three CMOS input gates (15 pF load) with 40 MHz clock. Resynchronization The Deserializer LOCK pin driven low indicates that the Deserializer PLL is locked to the embedded clock edge. If the Deserializer loses lock, the LOCK output will go high and the outputs (including RCLK) will be TRI-STATE. The LOCK pin must be monitored by the system to detect a loss of synchronization and the system must arrange to pulse the Serializer SYNC1 or SYNC2 pin to resynchronize. There are multiple approaches possible. One recommenda- tion is to provide a feedback loop using the LOCK pin itself to control the sync request of the Serializer (SYNC1 or SYNC2). Otherwise, LOCK pin needs to be monitored and when it is a high, the system needs to ensure that one or both of the Serializer SYNC inputs area asserted for at least 1024 cycles of TCLK. A minimum of 1024 sync patterns are needed to resynchronize. Dual SYNC pins are provided for multiple control in a multi-drop application. Powerdown The Powerdown state is a low power sleep mode that the Serializer and Deserializer may use to reduce power when there is no data to be transferred. Powerdown is entered when PWRDN and REN are driven low on the Deserializer, and when the PWRDN is driven low on the Serializer. In Powerdown, the PLL is stopped and the outputs go into TRI-STATE, disabling load current and also reducing supply current to the milliamp range. To exit Powerdown, PWRDN is driven high. Both the Serializer and Deserializer must reinitialize and resynchronize before data can be transferred. Initialization of the Serializer takes 1024 TCLK cycles. The Deserializer will initialize and assert LOCK high until it is locked to the Bus LVDS clock. TRI-STATE For the Serializer, TRI-STATE is entered when the DEN pin is driven low. This will TRI-STATE both driver output pins (DO+ and DO−). When DEN is driven high the serializer will return to the previous state as long as all other control pins remain static (SYNC1, SYNC2, PWRDN, TCLK_R/F). For the Deserializer, TRI-STATE is entered when the REN pin is driven low. This will TRI-STATE the receiver output pins (ROUT0–ROUT9), LOCK and RCLK. Order Numbers NSID Function Package DS92LV1021TMSA Serializer MSA28 DS92LV1210TMSA Deserializer MSA28 DS92LV1021 and DS92LV1210 www.national.com3
Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V CC) −0.3V to +4V CMOS/TTL Input Voltage −0.3V to (V CC +0.3V) CMOS/TTL Output Voltage −0.3V to (V CC +0.3V) Bus LVDS Receiver Input Voltage −0.3V to +3.9V Bus LVDS Driver Output Voltage −0.3V to +3.9V Bus LVDS Output Short Circuit Duration Continuous Junction Temperature +150˚C Storage Temperature −65˚C to +150˚C Lead Temperature (Soldering, 4 seconds) +260˚C Maximum Package Power Dissipation Capacity @ 25˚C Package: 28L SSOP 1.27 W Package Derating: 28L SSOP 10.2 mW/˚C above +25˚C ESD Rating (HBM) >5kV Recommended Operating Conditions Min Nom Max Units Supply Voltage (VCC) 3.0 3.3 3.6 V Operating Free Air Temperature (TA) −40 +25 +85 ˚C Receiver Input Range 0 2.4 V Supply Noise Voltage (VCC) 100 mVP-P
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units SERIALIZER CMOS/TTL DC SPECIFICATIONS (apply to DIN0-9, TCLK, PWRDN, TCLK_R/F, SYNC1, SYNC2, DEN) VIH High Level Input Voltage 2.0 V CC V VIL Low Level Input Voltage GND 0.8 V VCL Input Clamp Voltage I CL = −18 mA −1.5 V IIN Input Current V IN = 0V or 3.6V −10 ±2 +10 µA DESERIALIZER CMOS/TTL DC SPECIFICATIONS (apply to pins PWRDN, RCLK_R/ F, REN, REFCLK = inputs; apply to pins ROUT, RCLK, LOCK = outputs) VIH High Level Input Voltage 2.0 V CC V VIL Low Level Input Voltage GND 0.8 V VCL Input Clamp Voltage I CL = −18 mA −0.62 −1.5 V IIN Input Current V IN = 0V or 3.6V −10 ±1 +10 µA VOH High Level Output Voltage I OH = −9 mA 2.1 2.93 V CC V VOL Low Level Output Voltage I OL = 9 mA GND 0.33 0.6 V IOS Output Short Circuit Current VOUT = 0V −15 −38 −85 mA IOZ TRI-STATE Output Current PWRDN or REN = 0.8V, V OUT =0 Vo rV C C −10 ±0.4 +10 µA SERIALIZER Bus LVDS DC SPECIFICATIONS (apply to pins DO+ and DO−) V OD Output Differential Voltage (DO+)–(DO−) R L=2 7Ω 200 270 mV ∆VOD Output Differential Voltage Unbalance 35 mV VOS Offset Voltage 0.78 1.1 1.3 V ∆VOS Offset Voltage Unbalance 35 mV IOS Output Short Circuit Current D0 = 0V, DIN = High,PWRDN and DEN = 2.4V −10 −15 mA IOZ TRI-STATE Output Current PWRDN or DEN = 0.8V, DO = 0V or VCC −10 ±1 +10 µA IOX Power-Off Output Current VCC = 0V, DO = 0V or VCC −20 ±1 +20 µA DESERIALIZER Bus LVDS DC SPECIFICATIONS (apply to pins RI+ and RI−) VTH Differential Threshold High Voltage VCM = +1.1V +19 +100 mV VTL Differential Threshold Low Voltage −100 −7 mV DS92LV1021 and DS92LV1210 www.national.com 4
Deserializer Timing Requirements for REFCLK Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units tRFCP REFCLK Period 25 T 62.5 ns tRFDC REFCLK Duty Cycle 50 % tRFCP / tTCP Ratio of REFCLK to TCLK Periods 0.83 1 1.03 t RFTT REFCLK Transition Time 3 6 ns Deserializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Pin/Freq. Min Typ Max Units tRCP Receiver out Clock Period Figure 9 tRCP =t TCP RCLK 25 62.5 ns tCLH CMOS/TTL Low-to-High Transition Time C L=1 5p F Figure 4 Rout(0-9), 25 n s tCHL CMOS/TTL High-to-Low Transition Time LOCK, RCLK 25 n s tDD Deserializer Delay Figure 10 1.75*tRCP 1.75*tRCP+3 1.75*t RCP+7 ns tROS ROUT (0-9) Setup Data to RCLK Figure 11 RCLK 0.4*tRCP 0.5*tRCP ns tROH ROUT (0-9) Hold Data to RCLK −0.4*tRCP −0.5*tRCP ns tRDC RCLK Duty Cycle 40 50 60 % tHZR HIGH to TRI-STATE Delay Figure 12 Rout(0-9), LOCK 4+0.5*tRCP 10+tRCP ns tLZR LOW to TRI-STATE Delay 4.2+0.5*tRCP 10+tRCP ns tZHR TRI-STATE to HIGH Delay 6+0.5*tRCP 12+tRCP ns tZLR TRI-STATE to LOW Delay 6.5+0.5*tRCP 12+tRCP ns tDSR1 Deserializer PLL Lock Time from PWRDWN (with SYNCPAT) (Note 5) Figure 13 Figure 14 16MHz 71 5 µ s 40MHz 4.8 25.6 µs t DSR2 Deserializer PLL Lock time from SYNCPAT 16MHz 7 10 µs 40MHz 4.5 7 µs tZHLK TRI-STATE to HIGH Delay (power-up) LOCK 1.5 12 ns tRNM Deserializer Noise Margin Figure 15 (Note 6)
16 MHz 400 1100 ps
40 MHz 100 400 ps
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. Note 2: Typical values are given for V CC = 3.3V and T A = +25˚C. Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground except VOD, ∆VOD, VTH and VTL which are differential voltages. Note 4: Due to TRI-STATE of the Serializer, the Deserializer will lose PLL lock and have to resynchronize before data transfer. Note 5: For the purpose of specifying deserializer PLL performance tDSR1 and tDSR2 are specified with the REFCLK running and stable, and specific conditions of the incoming data stream (SYNCPATs). It is recommended that the derserializer be initialized using either tDSR1 timing or tDSR2 timing. tDSR1 is th e time required for the deserializer to indicate lock upon power-up or when leaving the power-down mode. Synchronization patterns should be sent to the devi ce before initiating either condition. tDSR2 is the time required to indicate lock for the powered-up and enabled deserializer when the input (RI+ and RI-) cond itions change from not receiving data to receiving synchronization patterns (SYNCPATs). Note 6: tRNM is a measure of how much phase noise (jitter) the deserializer can tolerate in the incoming data stream before bit errors occur. DS92LV1021 and DS92LV1210 www.national.com 6
Differential output signal is shown as (DO+)–(DO−), device in Data Transfer mode. FIGURE 15. Receiver Bus LVDS Input Skew Margin
Application Information
USING THE DS92LV1021 AND DS92LV1210 The Serializer and Deserializer chipset is an easy to use transmitter and receiver pair that sends 10 bits of parallel TTL data over a serial Bus LVDS link up to 400 Mbps. Serialization of the input data is accomplished using an onboard PLL at the Serializer which embeds two clock bits with the data. The Deserializer uses a separate reference clock (REFCLK) and an onboard PLL to extract the clock information from the incoming data stream and deserialize the data. The Deserializer monitors the incoming clock infor- mation to determine lock status and will indicate loss of lock by raising the LOCK output. POWER CONSIDERATIONS All CMOS design of the Serializer and Deserializer makes them inherently low power devices. Additionally, the constant current source nature of the Bus LVDS outputs minimize the slope of the speed vs. I CC curve of CMOS designs. POWERING UP THE SERIALIZER The DS92LV1021 must be powered up using a specific sequence to properly start the PLL up. Not following the sequence can cause the Bus LVDS outputs to be stuck in a certain output state. This may occur if the TCLK input is driven before power is applied to the Serializer. It is impor- tant to note that this is not a latch up condition: no excessive current is drawn by the Serializer in this state and the power does not need to be cycled to recover from this state. Cycling the PWRDWN pin from high to low and back to high will reset the PLL and return the Serializer to normal operation. To avoid this condition, the Serializer should be powered up (ALL V CC pins) simultaneously with the PWRDWN pin held low for 1µs. Do not float the PWRDWN pin, external pull resistor is recommended. Once the V CC pins have stabilized the TCLK input can be driven and the Serializer will be ready for data transmission. POWERING UP THE DESERIALIZER The DS92LV1210 can be powered up at any time following the proper sequence. The REFCLK input can be running before the Deserializer is powered up and it must be running in order for the Deserializer to lock to incoming data. The Deserializer outputs will remain in TRI-STATE ™ until the Deserializer detects data transmission at its inputs and locks to the incoming stream. The recommended power up se- quence for the deserializer is to power up all V CC pins simultaneously with the PWRDWN pin held low for 1µs. Once the V CC pins have stabilized the Deserializer is ready for locking. Another option to ensure proper power up is to cycle the PWRDWN pin from high to low and back to high after power up. TRANSMITTING DATA Once the Serializer and Deserializer are powered up and running they must be phase locked to each other in order to transmit data. Phase locking is accomplished by the Serial- izer sending SYNC patterns to the Deserializer. SYNC pat- terns are sent by the Serializer whenever SYNC1 or SYNC2 inputs are held high. The LOCK output of the Deserializer is high whenever the Deserializer is not locked. Connecting the LOCK output of the Deserializer to one of the SYNC inputs of the Serializer will guarantee that enough SYNC patterns are sent to achieve Deserializer lock. While the Deserializer LOCK output is low, data at the De- serializer outputs (ROUT0-9) is valid except for the specific case of loss of lock during transmission. NOISE MARGIN The Deserializer noise margin is the amount of input jitter (phase noise) that the Deserializer can tolerate and still reliably receive data. Various environmental and systematic factors include: Serializer: TCLK jitter, V CC noise (noise bandwidth and out-of-band noise) Media: ISI, VCM noise Deserializer: VCC noise RECOVERING FROM LOCK LOSS In the case where the Serializer loses lock during data transmission up to 5 cycles of data that was previously received can be invalid. This is due to the delay in the lock detection circuit. The lock detect circuit requires that invalid clock information be received 4 times in a row to indicate loss of lock. Since clock information has been lost it is possible that data was also lost during these cycles. When the Deserializer LOCK pin goes low, data from at least the previous 5 cycles should be resent upon regaining lock. Lock can be regained at the Deserializer by causing the Serializer to resend SYNC patterns as described above. PCB CONSIDERATIONS The Bus LVDS devices Serializer and Deserializer should be placed as close to the edge connector as possible. In mul- tiple Deserializer applications, the distance from the Deseri- alizer to the slot connector appears as a stub to the Serial- izer driving the backplane traces. Longer stubs lower the impedance of the bus increasing the load on the Serializer and lowers threshold margin at the Deserializers. Deserial- izer devices should be placed no more than 1 inch from the slot connector. TRANSMISSION MEDIA The Serializer and Deserializer are designed for data trans- mission over a multi-drop bus. Multi-drop buses use a single Serializer and multiple Deserializer devices. Since the Seri- alizer can be driving from any point on the bus, the bus must be terminated at both ends. For example, a 100 Ohm differ- ential bus must be terminated at each end with 100 Ohms lowering the DC impedance that the Serializer must drive to 50 Ohms. This load is further lowered by the addition of multiple Deserializers. Adding up to 20 Deserializers to the bus (depending upon spacing) will lower the total load to about 27 Ohms (54 Ohm bus). The Serializer is designed for DC loads between 27 and 100 Ohms. The Serializer and Deserializer can also be used in point-to- point configuration of a backplane, PCB trace or through a twisted pair cable. In point-to-point configurations the trans- mission media need only be terminated at the receiver end. In the point-to-point configuration the potential of offsetting the ground levels of the Serializer vs. the Deserializer must be considered. Bus LVDS provides a plus / minus one volt common mode range at the receiver inputs. DS92LV1021 and DS92LV1210 www.national.com13
DS92LV1021TMSA - Serializer 10011018 DS92LV1210TMSA - Deserializer 10011019 DS92LV1021 and DS92LV1210 www.national.com 14
Serializer Pin Description Pin Name I/O No. Description DIN I 3–12 Data Input. TTL levels inputs. Data on these pins are loaded into a 10-bit input register. TCLK_R/F I 13 Transmit Clock Rising/Falling strobe select. TTL level input. Selects TCLK active edge for strobing of DIN data. High selects rising edge. Low selects falling edge. DO+ O 22 + Serial Data Output. Non-inverting Bus LVDS differential output. DO− O 21 − Serial Data Output. Inverting Bus LVDS differential output. DEN I 19 Serial Data Output Enable. TTL level input. A low, puts the Bus LVDS outputs in TRI-STATE. PWRDN I 24 Powerdown. TTL level input. PWRDN driven low shuts down the PLL and TRI-STATEs outputs putting the device into a low power sleep mode. Do not float the PWRDWN pin, external pull resistor is recommended. A pull-down will disable the device until it is actively driven (enabled). TCLK I 14 Transmit Clock. TTL level input. Input for 16 MHz–40 MHz (nominal) system clock. SYNC I 1, 2 Assertion of SYNC (high) for at least 1024 synchronization symbols to be transmitted on the Bus LVDS serial output. Synchronization symbols continue to be sent if SYNC continues asserted. TTL level input. The two SYNC pins are ORed. DVCC I 27, 28 Digital Circuit power supply. DGND I 15, 16 Digital Circuit ground. AVCC I 17, 26 Analog power supply (PLL and Analog Circuits). AGND I 18, 25, 20, 23 Analog ground (PLL and Analog Circuits). DS92LV1021 and DS92LV1210 www.national.com15
Deserializer Pin Description Pin Name I/O No. Description ROUT O 15–19, 24–28 Data Output. ±9 mA CMOS level outputs. RCLK_R/F I 2 Recovered Clock Rising/Falling strobe select. TTL level input. Selects RCLK active edge for strobing of ROUT data. High selects rising edge. Low selects falling edge. RI+ I 5 + Serial Data Input. Non-inverting Bus LVDS differential input. RI− I 6 − Serial Data Input. Inverting Bus LVDS differential input. PWRDN I 7 Powerdown. TTL level input. PWRDN driven low shuts down the PLL and TRI-STATEs outputs putting the device into a low power sleep mode. LOCK O 10 LOCK goes low when the Deserializer PLL locks onto the embedded clock edge. CMOS level output. Totem pole output structure, does not directly support wire OR connection. RCLK O 9 Recovered Clock. Parallel data rate clock recovered from embedded clock. Used to strobe ROUT, CMOS level output. REN I 8 Output Enable. TTL level input. TRI-STATEs ROUT0–ROUT9, LOCK and RCLK when driven low. DVCC I 21, 23 Digital Circuit power supply. DGND I 14, 20, 22 Digital Circuit ground. AVCC I 4, 11 Analog power supply (PLL and Analog Circuits). AGND I 1, 12, 13 Analog ground (PLL and Analog Circuits). REFCLK I 3 Use this pin to supply a REFCLK signal for the internal PLL frequency. DS92LV1021 and DS92LV1210 www.national.com 16
DIN (0–9) TCLK_R/F TCLK SYNC1/SYNC2 DEN PWRDN DO+ DO− XXX X X 0ZZ XXX X 0 1ZZ X X SYSTEM CLK 1∼ 1 1 SYNC PTRN SYNC PTRN* DATA 1 L 0 1 1 DATA (0–9) DATA (0–9)* DATA 0 K 0 1 1 DATA (0–9) DATA (0–9)* RI RI− RCLK_R/F REFCLK REN PWRDN RCLK LOCK ROUT (0–9) XXX X X 0ZZZ XXX X 0 * * 1ZZZ SYNC PTRN SYNC PTRN* X SYSTEM CLK 1 1 CLK 1 † SYNC PTRN DATA (0–9) DATA (0–9)* 1 SYSTEM CLK 1 1 L 0 DATA DATA (0–9) DATA (0–9)* 0 SYSTEM CLK 1 1 K 0 DATA ∼ Pulse 5-bits * Inverted †Must be 1 before SYNC PTRN starts ** Device must be locked first DS92LV1021 and DS92LV1210 www.national.com17
Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS92LV1021TMSA or DS92LV1210TMSA LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Corporation Americas Email: support@nsc.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 www.national.com DS92LV1021 and DS92LV1210 16-40 MHz 10 Bit Bus LVDS Serializer and Deserializer National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the righ t at any time without notice to change said circuitry and specifications.