DS92LV1023TMSA

DS92LV1023 NSC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 13

Technical content

Features

n 40–66 MHz Single 10:1 Serializer with 400–660 Mb/s throughput n Robust Bus LVDS serial data transmission with embedded clock for exceptional noise immunity and low EMI n Guaranteed transition every data transfer cycle n Low power consumption < 250 mW (typ) @ 66 MHz n Single differential pair eliminates multichannel skew n Flow-through pinout for easy PCB layout n Programmable edge trigger on clock n High impedance on driver outputs when power is off n Bus LVDS serial output rated for 27 Ω load n Small 28-lead SSOP package Block Diagrams 10093301 TRI-STATE® is a registered trademark of National Semiconductor Corporation. April 2005 DS92LV1023 40-66 MHz 10 Bit Bus LVDS Serializer © 2005 National Semiconductor Corporation DS100933 www.national.com

Block Diagrams (Continued) Application 10093302 Functional Description The DS92LV1023 is a 10-bit Serializer device which together with a compatible deserializer (i.e. DS92LV1224) forms a chipset designed to transmit data over FR-4 printed circuit board backplanes and balanced copper cables at clock speeds from 40 to 66 MHz. The chipset has three active states of operation: Initializa- tion, Data Transfer, and Resynchronization; and two passive states: Powerdown and TRI-STATE The following sections describe each operation and passive state. Initialization Initialization of both devices must occur before data trans- mission begins. Initialization refers to synchronization of the Serializer and Deserializer PLL’s to local clocks, which may be the same or separate. Afterwards, synchronization of the Deserializer to Serializer occurs. Step 1: When you apply V CC to both Serializer and/or Dese- rializer, the respective outputs enter TRI-STATE ®, and on- chip power-on circuitry disables internal circuitry. When VCC reaches VCCOK (2.5V) the PLL in each device begins lock- ing to a local clock. For the Serializer, the local clock is the transmit clock (TCLK) provided by the source ASIC or other device. For the Deserializer, you must apply a local clock to the REFCLK pin. The Serializer outputs remain in TRI-STATE while the PLL locks to the TCLK. After locking to TCLK, the Serializer is now ready to send data or SYNC patterns, depending on the levels of the SYNC1 and SYNC2 inputs or a data stream. The SYNC pattern sent by the Serializer consists of six ones and six zeros switching at the input clock rate. Note that the Deserializer LOCK output will remain high while its PLL locks to the incoming data or to SYNC patterns on the input. Step 2: The Deserializer PLL must synchronize to the Seri- alizer to complete initialization. The Deserializer will lock to non-repetitive data patterns. However, the transmission of SYNC patterns enables the Deserializer to lock to the Seri- alizer signal within a specified time. See Figure 7. The user’s application determines control of the SYNC1 and SYNC 2 pins. One recommendation is a direct feedback loop from the LOCK pin. Under all circumstances, the Serializer stops sending SYNC patterns after both SYNC inputs return low. When the Deserializer detects edge transitions at the Bus LVDS input, it will attempt to lock to the embedded clock information. When the Deserializer locks to the Bus LVDS clock, the LOCK output will go low. When LOCK is low, the Deserializer outputs represent incoming Bus LVDS data. Data Transfer After initialization, the Serializer will accept data from inputs DIN0–DIN9. The Serializer uses the TCLK input to latch incoming Data. The TCLK_R/F pin selects which edge the Serializer uses to strobe incoming data. TCLK_R/F high selects the rising edge for clocking data and low selects the falling edge. If either of the SYNC inputs is high for 5*TCLK cycles, the data at DIN0-DIN9 is ignored regardless of clock edge. After determining which clock edge to use, a start and stop bit, appended internally, frame the data bits in the register. The start bit is always high and the stop bit is always low. The start and stop bits function as the embedded clock bits in the serial stream. The Serializer transmits serialized data and clock bits (10+2 bits) from the serial data output (DO ±) at 12 times the TCLK frequency. For example, if TCLK is 66 MHz, the serial rate is 66 x 12 = 792 Mega-bits-per-second. Since only 10 bits are from input data, the serial “payload” rate is 10 times the TCLK frequency. For instance, if TCLK = 66 MHz, the pay- load data rate is 66 x 10 = 660 Mbps. The data source provides TCLK and must be in the range of 40 MHz to 66 MHz nominal. The Serializer outputs (DO ±) can drive a point-to-point con- nection or in limited multi-point or multi-drop backplanes. The outputs transmit data when the enable pin (DEN) is high, PWRDN = high, and SYNC1 and SYNC2 are low. When DEN is driven low, the Serializer output pins will enter TRI-STATE. When the Deserializer synchronizes to the Serializer, the LOCK pin is low. The Deserializer locks to the embedded DS92LV1023 www.national.com 2

Data Transfer (Continued) clock and uses it to recover the serialized data. ROUT data is valid when LOCK is low. Otherwise ROUT0–ROUT9 is invalid. The ROUT0-ROUT9 pins use the RCLK pin as the reference to data. The polarity of the RCLK edge is controlled by the RCLK_R/F input. ROUT(0-9), LOCK and RCLK outputs will drive a maximum of three CMOS input gates (15 pF load) with a 66 MHz clock. Resynchronization When the Deserializer PLL locks to the embedded clock edge, the Deserializer LOCK pin asserts a low. If the Dese- rializer loses lock, the LOCK pin output will go high and the outputs (including RCLK) will enter TRI-STATE. The user’s system monitors the LOCK pin to detect a loss of synchronization. Upon detection, the system can arrange to pulse the Serializer SYNC1 or SYNC2 pin to resynchronize. Multiple resynchronization approaches are possible. One recommendation is to provide a feedback loop using the LOCK pin itself to control the sync request of the Serializer (SYNC1 or SYNC2). Dual SYNC pins are provided for mul- tiple control in a multi-drop application. Sending sync pat- terns for resynchronization is desirable when lock times within a specific time are critical. However, the Deserializer can lock to random data, which is discussed in the next section. Random Lock Initialization and Resynchronization The initialization and resynchronization methods described in their respective sections are the fastest ways to establish the link between the Serializer and Deserializer. However, the DS92LV1224 can attain lock to a data stream without requiring the Serializer to send special SYNC patterns. This allows the DS92LV1224 to operate in “open-loop” applica- tions. Equally important is the Deserializer’s ability to support hot insertion into a running backplane. In the open loop or hot insertion case, we assume the data stream is essentially random. Therefore, because lock time varies due to data stream characteristics, we cannot possibly predict exact lock time. The primary constraint on the “random” lock time is the initial phase relation between the incoming data and the REFCLK when the Deserializer powers up. As described in the next paragraph, the data contained in the data stream can also affect lock time. If a specific pattern is repetitive, the Deserializer could enter “false lock” - falsely recognizing the data pattern as the clocking bits. We refer to such a pattern as a repetitive multi-transition, RMT. This occurs when more than one Low- High transition takes place in a clock cycle over multiple cycles. This occurs when any bit, except DIN 9, is held at a low state and the adjacent bit is held high, creating a 0-1 transition. In the worst case, the Deserializer could become locked to the data pattern rather than the clock. Circuitry within the DS92LV1224 can detect that the possibility of “false lock” exists. The circuitry accomplishes this by detect- ing more than one potential position for clocking bits. Upon detection, the circuitry will prevent the LOCK output from becoming active until the potential “false lock” pattern changes. The false lock detect circuitry expects the data will eventually change, causing the Deserializer to lose lock to the data pattern and then continue searching for clock bits in the serial data stream. Graphical representations of RMT are shown in Figure 1. Please note that RMT only applies to bits DIN0-DIN8. Powerdown When no data transfer occurs, you can use the Powerdown state. The Serializer and Deserializer use the Powerdown state, a low power sleep mode, to reduce power consump- tion. The Deserializer enters Powerdown when you drive PWRDN and REN low. The Serializer enters Powerdown when you drive PWRDN low. In Powerdown, the PLL stops and the outputs enterTRI-STATE, which disables load cur- rent and reduces supply current to the milliampere range. To exit Powerdown, you must drive the PWRDN pin high. Before valid data exchanges between the Serializer and Deserializer, you must reinitialize and resynchronize the de- vices to each other. Initialization of the Serializer takes 510 TCLK cycles. The Deserializer will initialize and assert LOCK high until lock to the Bus LVDS clock occurs. TRI-STATE The Serializer enters TRI-STATE when the DEN pin is driven low. This puts both driver output pins (DO+ and DO−) into TRI-STATE. When you drive DEN high, the Serializer returns to the previous state, as long as all other control pins remain static (SYNC1, SYNC2, PWRDN, TCLK_R/F). When you drive the REN pin low, the Deserializer enters TRI-STATE. Consequently, the receiver output pins (ROUT0–ROUT9) and RCLK will enter TRI-STATE. The LOCK output remains active, reflecting the state of the PLL. DS92LV1023 www.national.com3

Ordering Information

DS92LV1023TMSA Serializer MSA28 10093324 DIN0 Held Low-DIN1 Held High Creates an RMT Pattern 10093325 DIN4 Held Low-DIN5 Held High Creates an RMT Pattern 10093326 DIN8 Held Low-DIN9 Held High Creates an RMT Pattern FIGURE 1. RMT Patterns Seen on the Bus LVDS Serial Output

Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V CC) −0.3V to +4V LVCMOS/LVTTL Input Voltage −0.3V to (V CC +0.3V) LVCMOS/LVTTL Output Voltage −0.3V to (V CC +0.3V) Bus LVDS Driver Output Voltage −0.3V to +3.9V Bus LVDS Output Short Circuit Duration 10mS Junction Temperature +150˚C Storage Temperature −65˚C to +150˚C Lead Temperature (Soldering, 4 seconds) +260˚C Maximum Package Power Dissipation Capacity @ 25˚C Package: 28L SSOP 1.27 W Package Derating: 28L SSOP 10.3 mW/˚C above +25˚C θja 97˚C/W θjc 27˚C/W ESD Rating HBM (1.5kOhm, 100pF) >1kV MM > 250V Recommended Operating Conditions Min Nom Max Units Supply Voltage (VCC) 3.0 3.3 3.6 V Operating Free Air Temperature (TA) −40 +25 +85 ˚C Supply Noise Voltage (VCC) 100 mVP-P

Electrical Characteristics

Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units SERIALIZER LVCMOS/LVTTL DC SPECIFICATIONS (apply to DIN0-9, TCLK, PWRDN, TCLK_R/F, SYNC1, SYNC2, DEN) VIH High Level Input Voltage 2.0 V CC V VIL Low Level Input Voltage GND 0.8 V VCL Input Clamp Voltage I CL = −18 mA -0.86 −1.5 V IIN Input Current V IN = 0V or 3.6V −10 ±1 +10 µA SERIALIZER Bus LVDS DC SPECIFICATIONS (apply to pins DO+ and DO−) V OD Output Differential Voltage (DO+)–(DO−) R L=2 7Ω, Figure 10 200 290 mV ∆VOD Output Differential Voltage Unbalance 35 mV VOS Offset Voltage 1.05 1.1 1.3 V ∆VOS Offset Voltage Unbalance 4.8 35 mV IOS Output Short Circuit Current D0 = 0V, DIN = High,PWRDN and DEN = 2.4V −56 −90 mA IOZ TRI-STATE Output Current PWRDN or DEN = 0.8V, DO = 0V or VCC −10 ±1 +10 µA IOX Power-Off Output Current VCC = 0V, DO=0V or 3.6V −20 ±1 +25 µA SERIALIZER SUPPLY CURRENT (apply to pins DVCC and AVCC) I CCD Serializer Supply Current RL = 27 Ω f = 40 MHz 47 60 mA Worst Case Figure 2 f = 66 MHz 75 90 mA ICCXD Serializer Supply Current Powerdown PWRDN = 0.8V 47 500 µA DS92LV1023 www.national.com5

AC Timing Diagrams and Test Circuits (Continued)

Application Information

USING THE SERIALIZER AND DESERIALIZER CHIPSET The Serializer and Deserializer chipset is an easy to use transmitter and receiver pair that sends 10 bits of parallel LVTTL data over a serial Bus LVDS link up to 660 Mbps. An on-board PLL serializes the input data and embeds two clock bits within the data stream. The Deserializer uses a separate reference clock (REFCLK) and an onboard PLL to extract the clock information from the incoming data stream and then deserialize the data. The Deserializer monitors the incoming clock information, determines lock status, and as- serts the LOCK output high when loss of lock occurs. POWER CONSIDERATIONS An all CMOS design of the Serializer and Deserializer makes them inherently low power devices. In addition, the constant current source nature of the Bus LVDS outputs minimizes the slope of the speed vs. I CC curve of conventional CMOS designs. TRANSMITTING DATA Once you power up the Serializer and Deserializer, they must be phase locked to each other to transmit data. Phase locking occurs when the Deserializer locks to incoming data or when the Serializer sends patterns. The Serializer sends SYNC patterns whenever the SYNC1 or SYNC2 inputs are high. The LOCK output of the Deserializer remains high until it has locked to the incoming data stream. Connecting the LOCK output of the Deserializer to one of the SYNC inputs of the Serializer will guarantee that enough SYNC patterns are sent to achieve Deserializer lock. The Deserializer can also lock to incoming data by simply powering up the device and allowing the “random lock” circuitry to find and lock to the data stream. While the Deserializer LOCK output is low, data at the De- serializer outputs (ROUT0-9) is valid, except for the specific case of loss of lock during transmission which is further discussed in the "Recovering from LOCK Loss" section be- low. HOT INSERTION All the BLVDS devices are hot pluggable if you follow a few rules. When inserting, ensure the Ground pin(s) makes con- tact first, then the VCC pin(s), and then the I/O pins. When removing, the I/O pins should be unplugged first, then the VCC, then the Ground. Random lock hot insertion is illus- trated in Figure 11. PCB CONSIDERATIONS The Bus LVDS Serializer and Deserializer should be placed as close to the edge connector as possible. In multiple Deserializer applications, the distance from the Deserializer to the slot connector appears as a stub to the Serializer driving the backplane traces. Longer stubs lower the imped- ance of the bus, increase the load on the Serializer, and lower the threshold margin at the Deserializers. Deserializer devices should be placed much less than one inch from slot connectors. Because transition times are very fast on the Serializer Bus LVDS outputs, reducing stub lengths as much as possible is the best method to ensure signal integrity. TRANSMISSION MEDIA The Serializer and Deserializer can also be used in point-to- point configuration of a backplane, through a PCB trace, or through twisted pair cable. In point-to-point configuration, the transmission media need only be terminated at the receiver end. Please note that in point-to-point configuration, the potential of offsetting the ground levels of the Serializer vs. the Deserializer must be considered. Also, Bus LVDS pro- vides a +/− 1.2V common mode range at the receiver inputs. 10093316 VOD = (DO+)–(DO−). Differential output signal is shown as (DO+)–(DO−), device in Data Transfer mode. FIGURE 10. VOD Diagram

FIGURE 11. Random Lock Hot Insertion

DS92LV1023TMSA - Serializer 10093318 Serializer Pin Description Pin Name I/O No. Description DIN I 3–12 Data Input. LVTTL levels inputs. Data on these pins are loaded into a 10-bit input register. TCLK_R/F I 13 Transmit Clock Rising/Falling strobe select. LVTTL level input. Selects TCLK active edge for strobing of DIN data. High selects rising edge. Low selects falling edge. DO+ O 22 + Serial Data Output. Non-inverting Bus LVDS differential output. DO− O 21 − Serial Data Output. Inverting Bus LVDS differential output. DEN I 19 Serial Data Output Enable. LVTTL level input. A low, puts the Bus LVDS outputs in TRI-STATE. PWRDN I 24 Powerdown. LVTTL level input. PWRDN driven low shuts down the PLL and TRI-STATEs outputs putting the device into a low power sleep mode. TCLK I 14 Transmit Clock. LVTTL level input. Input for 40 MHz–66 MHz (nominal) system clock. SYNC I 1, 2 Assertion of SYNC (high) for at least 1024 synchronization symbols to be transmitted on the Bus LVDS serial output. Synchronization symbols continue to be sent if SYNC continues asserted. TTL level input. The two SYNC pins are ORed. DVCC I 27, 28 Digital Circuit power supply. DGND I 15, 16 Digital Circuit ground. AVCC I 17, 26 Analog power supply (PLL and Analog Circuits). AGND I 18, 25, 20, 23 Analog ground (PLL and Analog Circuits). DS92LV1023 www.national.com 12

Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS92LV1023TMSA National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 www.national.com DS92LV1023 40-66 MHz 10 Bit Bus LVDS Serializer