DS61 LUMILEDS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 28

Technical content

DS061 LUXEON Rebel ES Product Datasheet ©2016 Lumileds Holding B.V. All rights reserved. RoHS COMPLIANT LUXEON Rebel ES is a high flux LED that gives you the flexibility you need to design luminaires and lamps for outdoor and industrial lighting applications and bring them to market. Tested and binned at 700mA, confidently design LUXEON Rebel ES into high lumen applications or create more energy efficient devices using the same emitter. Luminaire manufacturers and designers count on LUXEON Rebel ES for quality, reliability and in-device performance. LUXEON Rebel ES High value and easy design-in FEATURES AND BENEFITS PRIMARY APPLICATIONS High lm/$ for cost competitive applications High Bay & Low Bay Broad portfolio of emitters for indoor and outdoor applications Outdoor CCT and CRI combinations to support a wide range of applications Specialty Lighting Extensive applications ecosystem for easy design-in and quick ROI LM-80 test report available

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. i Table of Contents

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 2 General Information Product Nomenclature LUXEON Rebel ES is tested and binned at 700mA, with current pulse duration of 20 ms. All characteristic charts where the thermal pad is kept at constant temperature (25°C typically) are measured with current pulse duration of 20 ms. Under these conditions, junction temperature and thermal pad temperature are the same. The LUXEON Rebel ES family of emitters contain a series of LEDs designed for Illumination applications. The part number designation for the LXML series is explained as follows: L X M L - A B C D Where: A — designates radiation pattern (value P for Lambertian) B — designates color (W for White) C — designates color variant (C for Cool-White, N for Neutral-White) D — designates test current (value 2 for 700mA) The part number designation for the LXH7 series is explained as follows: L X H A - B C D E Where: A — designates minimum CRI performance (value 7 = 70 minimum) B — designates radiation pattern (value P for Lambertian) C — designates color (value W = White) D & E — designates nominal ANSI CCT (value 40 = 4000K)) Therefore products tested and binned at 700mA follow the part numbering scheme: L X M L - P W x 2 and L X H 7 - P W x x

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 3 Average Lumen Maintenance Characteristics Lumen maintenance for solid state lighting devices (LEDs) is typically defined in terms of the percentage of initial light output remaining after a specified period of time. Lumileds projects that LUXEON Rebel ES products will deliver, on average, 70% lumen maintenance (L70) at 50,000 hours of operation at a forward current of 1000mA. This projection is based on constant current operation with junction temperature maintained at or below 135°C. This performance is based on independent test data, Lumileds historical data from tests run on similar material systems, and internal LUXEON reliability testing. Observation of design limits included in this data sheet is required in order to achieve this projected lumen maintenance. Environmental Compliance Lumileds LLC is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON Rebel ES is compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the RoHS Directive 2011/65/EU and REACH Regulation (EC) 1907/2006. Lumileds LLC will not intentionally add the following restricted materials to its products: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE).

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 4 Product Selection Guide for LUXEON Rebel ES Thermal Pad Temperature = 25°C Table 1. Performance at Test Current (700mA) Nominal CCT/Color Part Number Minimum CRI Typical CRI Min Luminous Flux (lm) [1] 4100K Neutral White LXML-PWN2 60 65 200 5650K Cool White LXML-PWC2 60 70 200 4000K LXH7-PW40 70 75 180 Note for Table 1: 1. Minimum luminous flux performance within published operating conditions. Lumileds maintains a tolerance of ± 6.5% on luminous flux measurements and ± 2 on CRI measurements.. Typical Luminous Flux Characteristics at 350mA, 700mA and 1000mA for LUXEON Rebel ES, Thermal Pad Temperature = 25°C Table 2. Nominal CCT/Color Part Number Typical Luminous Flux (lm) @ 350mA Forward Current [1] Typical Luminous Flux (lm) @ 700mA Forward Current [1] Typical Luminous Flux (lm) @ 1000mA Forward Current [1] 4100K Neutral White LXML-PWN2 130 230 310 5650K Cool White LXML-PWC2 135 235 320 4000K LXH7-PW40 114 205 279 Note for Table 2: 1. Typical luminous flux performance within published operating conditions. Lumileds maintains a tolerance of ± 6.5% on luminous flux measurments. Optical Characteristics for LUXEON Rebel ES at Test Current [1] Thermal Pad Temperature = 25°C Table 3. Part Number Nominal CCT Color Temperature CCT Typ Total Included Angle [2] u0.90V Typ Viewing Angle [3] 2u 1/2Minimum Typical Maximum LXML-PWN2 4100K Neutral White 3500K 4100K 4500K 160° 120° LXML-PWC2 5650K Cool White 4500K 5650K 10000K 160° 120° LXH7-PW40 4000K 3710K 3985K 4260K 160° 120° Notes for Table 3: 1. Test current is 700mA for all LXML-PWx2 and LXH7-PWxx emitters. 2. Total angle at which 90% of total luminous flux is captured. 3. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value.

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 5 Electrical Characteristics at 700mA for LUXEON Rebel ES Thermal Pad Temperature = 25°C Table 4. Part Number Nominal CCT/Color Forward Voltage Vf [1] (V) Typ. Temperature Coefficient of Forward Voltage [2] (mV/°C) DVf / DTJ Typical Thermal Resistance Junction to Thermal Pad (°C/W) Ru J-C Minimum Typical Maximum Notes for Table 4: 1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements. 2. Measured between 25°C = TJ = 110°C at If = 700mA. Typical Electrical Characteristics at 350mA, 700mA and 1000mA for LUXEON Rebel ES Thermal Pad Temperature = 25°C Table 5. Nominal CCT/Color Part Number Typical Forward Voltage Vf (V) @ 350mA Forward Current Typical Forward Voltage Vf (V) @ 700mA Forward Current Typical Forward Voltage Vf (V) @ 1000mA Forward Current 4100K Neutral White LXML-PWN2 2.75 3.00 3.10 5650K Cool White LXML-PWC2 2.75 3.00 3.10 4000K LXH7-PW40 2.75 3.00 3.10 Notes for Table 5: 1. Lumileds maintains a tolerance of ±0.06V on forward voltage measurements.

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 6 Absolute Maximum Ratings Table 6. Parameter LUXEON Rebel ES DC Forward Current (mA) 1000 [2] Peak Pulsed Forward Current (mA) 1200 [3] ESD Sensitivity < 8000V Human Body Model (HBM) Class 3A JESD22-A114-E LED Junction Temperature [1] 150°C Operating Case Temperature at 700mA -40°C - 135°C Storage Temperature -40°C - 135°C Soldering Temperature JEDEC 020c 260°C Allowable Reflow Cycles 3 Reverse Voltage (Vr) LUXEON Rebel ES LEDs are not designed to be driven in reverse bias Notes for Table 6: 1. Proper current derating must be observed to maintain junction temperature below the maximum. For additional information on thermal measurement guidelines please refer to Application Brief AB33. 2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called “ripple’, with frequencies ≥ 100 Hz and amplitude ≤ 200mA are acceptable, assuming the average current throughout each cycle does not exceed 1000mA. 3. Pulsed operation with a peak drive current of 1200mA is acceptable if the pulse on-time is ≤ 5 ms per cycle and the duty cycle is ≤ 50%. JEDEC Moisture Sensitivity Table 7. Level Floor Life Soak Requirements Standard Time Conditions Time Conditions 1 unlimited [ 30°C / 85% RH 168h + 5 / - 0 85°C / 85% RH

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 7 Reflow Soldering Characteristics Temperature profile for Table 8. Table 8. Profile Feature Lead Free Assembly Average Ramp-Up Rate (Tsmax to Tp) 3°C / second max Preheat Temperature Min (Tsmin) 150°C Preheat Temperature Max (Tsmax) 200°C Preheat Time (tsmin to tsmax) 60 - 180 seconds Temperature (TL) 217°C Time Maintained Above Temperature (TL) 60 - 150 seconds Peak / Classification Temperature (TP) 260°C Time Within 5°C of Actual Peak Temperature (tP) 20 - 40 seconds Ramp - Down Rate 6°C / second max Time 25°C to Peak Temperature 8 minutes max Notes for Table 8: 1. All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package body. 2. For additional information on thermal measurement guidelines please refer to Application Brief AB33. JEDEC 020c

  1. Do not handle the device by the lens—care must be taken to avoid damage to the lens or the interior of the device that can be damaged by excessive force to the lens.
  2. All dimensions are in millimeters.
  3. The thermal pad is electrically isolated from the anode and cathode contact pads.

Figure 1. Package outline drawing.

  1. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads.
  2. The photograph shows the recommended LUXEON Rebel ES layout on Printed Circuit Board (PCB). This design easily achieves a thermal resistance of 7K/W.

2 ANODE

1 CATHODE

Figure 2. Pad configuration. Figure 3. Solder pad layout.

Figure 6. Color spectrum of LXH7-PW40 emitter, integrated measurement.

Figure 16. Relative luminous efficacy vs. thermal pad temperature, test current 700mA.

Figure 19. Maximum forward current vs. ambient temperature, based on TJMAX = 150°C.

Figure 20. Typical representative spatial radiation pattern for 4100K neutral white and 5650K cool white lambertian.

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 18 Emitter Pocket Tape Packaging 100020 50

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 19 Emitter Reel Packaging

DS061 LUXEON Rebel ES Product Datasheet 20160628 ©2016 Lumileds Holding B.V. All rights reserved. 20 Product Binning and Labeling Purpose of Product Binning In the manufacturing of semiconductor products, there is a variation of performance around the average values given in the technical data sheets. For this reason, Lumileds bins the LED components for luminous flux, color and forward voltage (Vf ). Decoding Product Bin Labeling LUXEON Rebel ES emitters are labeled using a four digit alphanumeric code (CAT code) depicting the bin values for emitters packaged on a single reel. All emitters packaged within a reel are of the same 3-variable bin combination. Using these codes, it is possible to determine optimum mixing and matching of products for consistency in a given application. Reels of LUXEON Rebel ES emitters are labeled with a four digit alphanumeric CAT code following the format below. A B C D A = Flux bin (P, Q, R, S etc.) B & C = Color bin (W0, V0, U0 etc. for LXML-PWx2 series. 5W, 5X, 5Y and 5Z for LXH7-PW40 emitter) D = Vf bin (P, R, S and T)

Not all bins are available in all colors. Table 9. Flux Bins transition may result in mixed shipments of old bin codes and new bin codes during calendar year 2013. Table 10. Flux Bins

Table 11. 4100K Neutral White Bin Coordinates

  1. Lumileds maintains a tester tolerence of ± 0.005 on x, y color coordinates.

Figure 21. 4100K Neutral White bin structure.

Figure 22. 5650K Cool White bin structure.

Table 12. 5650K Cool White Bin Coordinates

  1. Lumileds maintains a tester tolerence of ± 0.005 on x, y color coordinates.

LUXEON Rebel ES emitters are tested and binned by x,y coordinates.

4 Color Bins, CCT Range 3710K to 4260K

Table 14. LUXEON Rebel ES ANSI 1/4th quadrant Bin Coordinates for LXH7-PW40 emitter Figure 24. LUXEON Rebel ES ANSI 1/4th quadrant bin structure (LXH7-PW40 emitter only).

are outlined, product availability in a particular bin varies by production run and by product performance. Table 15. Vf Bins

Product Datasheet 20160628 Neither Lumileds Holding B.V. nor its affiliates shall be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided informa- tion and data. Although Lumileds Holding B.V. and/or its affiliates have attempted to provide the most accurate information and data, the materials and services information and data are provided “as is,” and neither Lumileds Holding B.V. nor its affiliates warrants or guarantees the contents and correctness of the provided information and data. Lumileds Holding B.V. and its affiliates reserve the right to make changes without notice. You as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data. About Lumileds Lumileds is the global leader in light engine technology. The company develops, manufactures and distributes groundbreaking LEDs and automotive lighting products that shatter the status quo and help customers gain and maintain a competitive edge. With a rich history of industry “firsts,” Lumileds is uniquely positioned to deliver lighting advancements well into the future by maintaining an unwavering focus on quality, innovation and reliability. To learn more about our portfolio of light engines, visit lumileds.com. ©2016 Lumileds Holding B.V. All rights reserved. LUXEON is a registered trademark of the Lumileds Holding B.V. in the United States and other countries. lumileds.com