DS3884

DS3884 MITEL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 12

Technical content

Supersedes version in December 1993 Digital Video & DSP IC Handbook, HB3923-1 DS3884 - 1.3 September 1996 The PDSP16330 is a high speed digital CMOS IC that converts Cartesian data (Real and Imaginary) into Polar form (Magnitude and Phase), at rates up to 20MHz. Cartesian 16+16 bit 2's complement or Sign-Magnitude data is converted into 16 bit Phase format. The Magnitude output may be scaled in amplitude by powers of 2. The Phase output represents a full 2 x π field to eliminate phase ambiguities. Polyimide is used as an inter-layer dielectric and as glassivation. The PDSP16330 is offered in three speed grades: a basic 10MHz part (PDSP16330), a 20MHz version (PDSP16330A) and a 25MHz version (PDSP16330). A MIL- STD-883 version is also detailed in a separate datasheet. Fig.1 Pin connections - bottom view (PGA) AC841234567891011 L K J H G F E D C B A PIN 1A INDEX MARK ON TOP SURFACE

FEATURES

25MHz Cartesian to Polar Conversion 16-Bit Cartesian Inputs 16-Bit Magnitude Output 12-Bit Phase Output 2’s Complement or Sign-Magnitude Input Formats Three-state Outputs and Independent Data Enables Simplify System Interfacing Magnitude Scaling Facility with Overflow Flag Less than 400 mW Power Dissipation at 10MHz 84-pin PGA or 100 pin QFP Package or 84 LCC

APPLICATIONS

PDSP16112 16 X 12 Complex Multiplier PDSP16116 16 X 16 Complex Multiplier PDSP16318 Complex Accumulator PDSP16350 I/Q Splitter and NCO PDSP16510A Stand Alone FFT Processor Fig.2 Pin connections - QFP Package GG100/R

The PDSP16330 converts incoming Cartesian Data into the equivalent Polar Values. The device accepts new 16 + 16 bit complex data every cycle, and delivers a 16 bit + 12 bit Polar equivalent after 24 clock cycles.The input data can be in 2s’ Complement or Sign Magnitude format selected via the FORM input. The output is in a magnitude format for both the Magnitude output and the Phase. Phase data is zero for data with a zero Y input and positive X, and is 400 hex for zero X data and positive Y, is 800 hex for zero Y data and negative X, and is C00 hex for zero X and negative Y. The LSB weighting (bit 0) is 2 x π/4096 radians. The 16 bit Magnitude result may be scaled by shifting one, two, or three places in the more significant direction, effectively multiplying the Magnitude result by 2,4 or 8 respectively. Any of these shifts can under certain conditions cause an invalid result to be output from the device. Under these circumstances the OVR output will become active. The PDSP16330 has independent clock enables and three state output controls for all ports. FORM This input selects the format of the X and Y input data. A low level on FORM indlcates that the Input data is twos’ complement format (Note: input data 8000 hex is not valid in 2s’ complement mode). This input refers to the format of the current Input data and may be changed on a per cycle basis if desired. The level of FORM is latched at the same time as the data to which it refers. S1-0 These inputs select the scaling factor to be applied to the Magnitude output. They are latched by the rising edge of CLK and determine the scaling of the output in the cycle after they are loaded into the device. The scale factor applied is determined by the table. Should the scaling factor applied cause an invalid Magnitude result to be output on the M Port, then the OVR Flag will become active for the period that the M Port output is invalid. The output number range is from 0 to 2 when the scaling factor is set at x1. Scaling Factor Fig.2 Block diagram π

Symbol Pin Name and Description CLK Clock: Common Clock to device Registers. Register contents change on the rising edge of clock. Both pins must be connected. CEX Clock Enable: Clock Enable for X Port. The clock to the X port is enabled by a low level. CEY Clock Enable: Clock Enable for Y Port The clock to the Y port is enabled by a low level. X15-X0 X Data Input Data presented to this input is loaded into the device by the rising edge of CLK. X15 is the MSB Y15-Y0 Y Data Input Data presented to this input is loaded into the device by the rising edge of CLK. Y15 is the MSB M15-M0 M Data Output: Magnitude data generated by the device is output on this port. Data changes on the rising edge of CLK, M15 is the MSB. The weighting of M15 is determined by the Scale factor selected . P11-P0 P Data Output: Phase data generated by the device is output on this port. Data changes on the rising edge of CLK, P11 is the MSB. The weighting of P11 is π radians. OEM Output Enable: Output Enable for M Port. The M Port is in a high impedance state when this input is high. OEP Output Enable: Output Enable for P Port. The P Port is in a high impedance state when this input is high. FORM Format Select This input selects the format of the Cartesian Data input on the X and Y ports. This input is latched by the rising edge of CLK, and is applied at the same time as the data to which it refers. A low !evel indicates that two’s complement data is applied, a high indicates Sign-Magnitude S1-S0 Scaling Control: Control input for scaling of Magnitude Data. This input is latched by the rising edge of CLK, and determines the scaling to be applied to the Magnitude result. The Scaling is applied to the output data in the cycle following the cycle in which the control was latched. OVR Overflow: Overflow flag. This signal becomes active if the scaling currently selected causes an invalid value to be presented to the Magnitude output. Vcc +5V supply. All Vcc pins must be connected. GND 0V supply. All GND pins must be connected. 2's Complement 7FFF 0001 0000 FFFF 8001 Sign Magnitude 7FFF 0001 FFF 0000 8000 INPUT DATA RANGE

1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3

ELECTRICAL CHARACTERISTICS

Test conditions (unless otherwise stated): Tamb (Commercial) = 0°C to + 70°C, Tamb (Industrial) = -40°C to + 85°C Vcc (Commercial) = 5.0V + 5%, Vcc (Industrial and Military) = 5.0V + 1%, GND = 0V STATIC CHARACTERISTICS Value Characteristic Symbol Units Conditions Min. Typ. Max. Output high voltage VOH 2.4 V IOH = 3.2mA Output low voltage VOL 0.6 V lOL=-3.2mA Input high voltage (CMOS) VIH 3.0 V Inputs CEX, CEY and CLK only Input low voltage (CMOS) VIL 1.0 V Inputs CEX, CEY and CLK only Input high voltage (TTL) VIH 2.2 V All other inputs Input low voltage (TTL) VIL 0.8 V All other inputs Input leakage current (Note 1 )IIL -10 + 120 µA GND < VIN<VCC Input capacitance C IN 10 pF Output leakage current loz -50 + 50 µA GND <VIN < VCC Output SC current IOS -50 230 mA Vcc = Max NOTES 1. All inputs except clock inputs have high value pull-down resistors 2. All parameters marked * are tested during production. Parameters marked † are guaranteed by design and characterisa- tion. Pin No. AC Function GND Vcc FORM Y15 Y14 Y13 Y12 Y11 Y10 Pin No. AC L10 L11 K10 J10 K11 J11 H10 H11 F10 G10 G11 F11 E11 E10 D11 D10 C11 B11 C10 A11 B10 A10 Function YO CEY CLK Vcc GND GND GND GND GND GND GND O EP P10 P11 GND Vcc C EX Pin No. AC Function X10 X11 X12 X13 X14 X15 CLK OVR Vcc GND O EM M15 M14 M13 M12 M11 M10 PIN FUNCTION GG 100 GG GG

Max. PDSP16330A Min. Max. 180 120 Characteristic † Input data setup to clock rising edge † Input data Hold after clock rising edge † CEX, CEY Setup to clock rising edge † CEX, CEY Hold aher clock rising edge † FORM, S1:0 Setup to clock rising edge † FORM, S1:0 Hold after clock rising edge † Clock rising edge to valid data * Clock period † Clock high time † Clock low time † Latency † OEM, OEP low to data high data valid † OEM, OEP low to data low data valid † OEM, OEP high to data high impedance † OEM, OEP low to data high impedance † Vcc current (TTL input levels) † Vcc current (CMOS input levels) SWITCHING CHARACTERISTICS NOTES 1. LSTTL is equivalent to IOH = 20µA, IOL = -0.4mA 2. Current is defined as negative into the device 3. CMOS input levels are defined as: VIH = VDD - 0.5V, VIL = +0.5V 4. All parameters marked * are tested during production. Parameters marked † are guaranteed by design and characterisation. 5. All timings are dependent on silicon speed. This speed is tested by measuring clock period. This guarantees all other timings by characterisation and design. Value PDSP16330 Min. 100 Max. 110 PDSP16330B Min. 225 150 Units ns ns ns ns ns ns ns ns ns ns cycles ns ns ns ns mA mA Conditions 2 x LSTTL + 20pF 2 x LSTTL + 20pF 2 x LSTTL + 20pF 2 x LSTTL + 20pF 2 x LSTTL + 20pF VCC = Max Outputs unloaded Clock freq. = Max VCC = Max Outputs unloaded Clock freq. = Max ABSOLUTE MAXIMUM RATINGS Supply voltage, Vcc -0.5V to + 7.0V Input voltage, VIN -0.5V to VCC + 0.5V Output voltage, Vour -0.5V to VCC + 0.5V Clamp diode current per pin, IK (see Note 2) ±18mA Static discharge voltage (HMB), VSTAT 500V Storage temperature. Tstg -65°C to + 150°C Ambient temperature with power applied Tamb : Commercial 0°C to + 70°C Industrial -40°C to + 85°C Military -55 °C to + 125°C Package power dissipation PTOT 1200mW Junction temperature 150°C THERMAL CHARACTERISTICS Package Type θJC°C/W θJA°C/W AC 12 36 GG 12 35 NOTES 1. Exceeding these ratings may cause permanent damage. Functional operatlon under these conditions is not implied. 2. Maximum dissipation or 1 second should not be exceeded; only one output to be tested at any one time. 3. Exposure to Absoulte Maximum Ratings for extended periods may affect device reliability.

ORDERING INFORMATION

Commercial (0°C to +70°C) PDSP16330 CO AC (10MHZ - PGA Package) PDSP16330A CO AC (20MHZ - PGA Package) PDSP16330B CO AC (25MHZ - PGA Package) Industrial (-40°C to +85°C) Military (-55°C to +125°C) PDSP16330 AC GG 10MHz - GG Package Mil 883C Screened PDSP16330A AC AC 20MHz - PGA Package Mil 883C Screened

Fig.3 Three state delay measurement load

Internet: http://www.gpsemi.com CUSTOMER SERVICE CENTRES l FRANCE & BENELUX Les Ulis Cedex Tel: (1) 69 18 90 00 Fax : (1) 64 46 06 07 l GERMANY Munich Tel: (089) 419508-20 Fax : (089) 419508-55 l ITALY Milan Tel: (02) 6607151 Fax: (02) 66040993 l JAPAN Tokyo Tel: (03) 5276-5501 Fax: (03) 5276-5510 l KOREA Seoul Tel: (2) 5668141 Fax: (2) 5697933 l NORTH AMERICA Scotts Valley, USA Tel: (408) 438 2900 Fax: (408) 438 5576/6231 l SOUTH EAST ASIA Singapore Tel:(65) 3827708 Fax: (65) 3828872 l SWEDEN Stockholm Tel: 46 8 702 97 70 Fax: 46 8 640 47 36 l TAIWAN, ROC Taipei Tel: 886 2 25461260 Fax: 886 2 27190260 l UK, EIRE, DENMARK, FINLAND & NORWAY Swindon Tel: (01793) 726666 Fax : (01793) 518582 These are supported by Agents and Distributors in major countries world-wide. © Mitel Corporation 1998 Publication No. DS3884 Issue No. 1.3 September 1996 TECHNICAL DOCUMENTATION – NOT FOR RESALE. PRINTED IN UNITED KINGDOM HEADQUARTERS OPERATIONS MITEL SEMICONDUCTOR Cheney Manor, Swindon, Wiltshire SN2 2QW, United Kingdom. Tel: (01793) 518000 Fax: (01793) 518411 MITEL SEMICONDUCTOR

1500 Green Hills Road,

Scotts Valley, California 95066-4922 United States of America. Tel (408) 438 2900 Fax: (408) 438 5576/6231 This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners.