DS2120 MAXIM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
1 of 10 REV: 010506
FEATURES
Fully Compliant with Ultra3, Ultra160, Ultra320, and Ultra2 (LVD only) SCSI Provides Low-Voltage Differential (LVD) Termination for Nine Signal Line Pairs Zero Temperature Coefficient Termination Resistors Autoselection of LVD Termination 5% Tolerance on LVD Termination Resistance Low Power-Down Capacitance of 3pF Built-In Mode Change Filter/Delay On-Board Thermal Shutdown Circuitry SCSI Bus Hot Plug Compatible PIN CONFIGURATION
APPLICATIONS
SCSI Host Bus Adapter Cards (HBA) Servers SCSI Cables Network Attached Storage (NAS) Storage Area Networks (SANs)
ORDERING INFORMATION
(V) PIN-PACKAGE TOP MARK* DS2120B 0°C to +70°C 5 36 SSOP DS2120 DS2120B/T&R 0°C to +70°C 5 36 SSOP/Tape and Reel DS2120 DS2120E 0°C to +70°C 5 28 TSSOP DS2120 DS2120E+ 0°C to +70°C 5 28 TSSOP DS2120 DS2120E/T&R 0°C to +70°C 5 28 TSSOP/Tape and Reel DS2120 DS2120E+T&R 0°C to +70°C 5 28 TSSOP/Tape and Reel DS2120 + Denotes lead-free/RoHS-compliant package. * The top mark includes a "+" on lead-free packages. DS2120 Ultra3 LVD SCSI Terminator www.maxim-ic.com NC R1P R1N VREF NC R2N HS GND HS GND R3P R3N R4P R4N R2P HS GND R5P R5N ISO GND LVD NC R9N R8N R8P HS GND HS GND HS GND R7N R7P R6N R9P TPWR NC DIFF_CAP DIFFSENSE MSTR/SLV R6P SSOP VREF HS GND R3P R3N R4P R4N R5P R5N ISO GND R1P R1N R2N R2P HS GND R7N R7P R6N TPWR DIFF_CAP DIFFSENSE MSTR/SLV R6P R9N R8N R8P R9P TPWR1 14 15 TSSOP
The DS2120 Ultra3 LVD SCSI terminator is a low-volta ge differential (LVD) terminator. If the device is connected in an LVD-only bus, the DS2120 uses LVD termination. If any single-ended (SE) or high- voltage differential (HVD) devices are connected to the bus, the DS 2120 disconnects from the bus. This is accomplished inside the part automatically by sensing the voltage on the SCSI bus DIFFSENS line. For the LVD termination, the DS2120 integrates two curre nt sources with nine precision resistor strings. Three DS2120 terminators are needed for a wide SCSI bus. REFERENCE DOCUMENTS Small Computer Systems Interface (SCSI-3) SCSI Parallel Interface (SPI) Project: 0855-M, 1995 Small Computer Systems Interface (SCSI-3) SCSI Parallel Interface 2 (SPI-2) Project: 1142-M, 1998 Small Computer Systems Interface (SCSI-3) SCSI Parallel Interface 3 (SPI-3) Project: 1302-D, 1999 Small Computer Systems Interface (SCSI-3) SCSI Parallel Interface 4 (SPI-4) Project: 1365-D, 200x Available from: American National Standards Institute (ANSI) Phone: 212-642-4900 Global Engineering Documents 15 Inverness Way East; Englewood, CO 80112 Phone: 800-854-7179 FUNCTIONAL DESCRIPTION The DS2120 combines LVD termination with DIFFSENSE sourcing and detection. LVD termination is provided by a laser-trimmed resi stor biased with two current sources and a common- mode voltage source, generated from a bandgap refe rence of 1.25V. The confi guration is a y-type terminator with a 105 Ω differential and 150 Ω common-mode resistance. A fail-safe bias of 112mV is maintained when no drivers are connected to the SC SI bus. In non-LVD mode, th e resistors are isolated from the bus. The DIFF_CAP pin of DS2120 monitors the DIFFSENS lin e to determine the proper operating mode of the device. If the voltage on the DIFF_CAP is between 0.7V and 1.9V, the device enters LVD mode after the mode-change delay. If the voltage at the DIFF_C AP later crosses one of the thresholds, the DS2120 again changes modes after the mode-change delay. The mode-change delay is the same when changing in or out of LVD mode. A new mode change can start anytime after a previous mode change has been detected. These modes are the following:
- LVD Mode: LVD termination is provided by a precision laser-trimmed resistor string with two current sources. This configuration yields a 105 Ω differential and 150 Ω common-mode impedance. A fail-safe bias of 112mV is maintain ed when no drivers are connected to the SCSI bus.
- SE Isolation Mode: The DS2120 identifies that there is a SE (single-ended) device on the SCSI bus and isolates the termination pins from the bus.
- HVD Isolation Mode: The DS2120 identifies that there is an HVD device on the SCSI bus and isolates the termination pins from the bus. When ISO is pulled high, the termination pins are is olated from the SCSI bus and VREF remains active. The mode-change delay/filter is still active and the L VD pin continues to indicate the correct bus mode.
During thermal shutdown, the termination pins are isol ated from the SCSI bus and VREF becomes high impedance. The DIFFSENS driver is shut down during either of these two events. The DIFF_CAP receiver is disabled and the LVD goes low, indicating a non-LVD condition. To ensure proper operation, the TPWR pin should be connected to the SCSI bus TERMPWR line. As with all analog circuitry, the TERMPWR and V DD lines should be bypassed locally. A 2.2 µF capacitor and a 0.01µF high-frequency capacitor are recommended between TPWR and ground and placed as close as possible to the DS2120. The DS2120 should be placed as close as possible to the SCSI connector to minimize signal and power trace length, thereby lessen ing input capacitance a nd reflections that can degrade the bus signals. To maintain the specified regulation, a 4.7 µF capacitor is requir ed between the VREF pin and ground of each DS2120. A high-frequency cap (0.1 µF ceramic recommended) can also be placed on the VREF pin in applications that use fast rise/fall-time drivers. A typical SCSI bus configuration is shown in Figure 2. DIFFSENS Noise Filtering: The DS2120 incorporates a digital filter to remove high-frequency transients on the DIFFSENS control line, thereby e liminating erroneous switchi ng between modes. This filter eliminates the need for the external capacitor and resistor, which previously performed this function. The external filter can be used in addition to th e digital filter if the DS2120 and DS2118M or DS2119M are to be used interchangeably. NOTES: 1) DIFFSENS: Refers to the SCSI bus signal. 2) DIFFSENSE: Refers to the Da llas Semiconductor pin name and internal circuitry relating to differential sensing.
Figure 1. Block Diagram
Figure 2. SCSI Bus Configuration
1 1 VREF Regulator Output Voltage. 1.25V reference in LVD mode; must be decoupled with a 4.7µF cap. 2–5, 7–12, 18–21, 23–26 4–7, 11–16, 22–25, 29–32 RxP, RxN Signal Termination. Connect to SCSI bus signal lines. 6, 22 8–10, 26–28 HS_GND Heat Sink Ground. Internally connected to the mounting pad. Should be connected to ground. 13 17 ISO Isolation. When pulled high, terminating resistors and biasing current sources are isolated from the SCSI bus. 14 18 GND Signal Ground 15 19 MSTR/SLV Master/Slave. Mode select for the noncontrolling terminator. When pulled high (MSTR), the DIFFSENS driver is enabled. 16 20 DIFFSENSE DIFFSENSE. Output to drive the SCSI bus DIFFSENS line. 17 21 DIFF_CAP DIFFSENSE Capacitor. Connect a 0.1µF capacitor for DIFFSENSE filter. Input to detect the type of device (differential or single-ended) on the SCSI bus. 27, 28 36 TPWR Termination Power. Connect to the SCSI TERMPWR line and decouple with 2.2µF capacitor. — 34 LVD Low-Voltage Differential. Output of DIFFSENSE receiver; output high indicates LVD bus operation. — 2, 3, 33, 35 NC No Connection. Do not connect pins. RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL MIN TYP MAX UNITS NOTES Termpower Voltage, LVD Mode V TPWR(LVD) 2.7 5.5 V Logic 0 V IL -0.3 +0.8 V 13 Logic 1 V IH 2.0 VTPWR +
0.3 V 13
Operating Temperature V AMB 0 70 °C
LOW-VOLTAGE DIFFERENTIAL CHARACTERISTICS PARAMETER SYMBOL MIN TYP MAX UNITS NOTES Differential Mode Termination Resistance RDM 100 110 Ω Common Mode Termination Resistance RCM 110 190 Ω Differential Mode Bias V DM 100 125 mV 2 Common Mode Bias V CM 1.125 1.375 V Output Capacitance C OUT 3 pF 1 Mode-Change Delay M CD 0.66 1.25 2 ms 1, 12 DC CHARACTERISTICS PARAMETER SYMBOL MIN TYP MAX UNITS NOTES Termpower Current I TPMR 12 30 mA 2, 3 Input Leakage High I IH -1.0 µA 14, 15 Input Leakage Low I IL 1.0 µA 14, 15 Output Current High I OH -1.0 mA 4, 6 Output Current Low I OL 4.0 mA 5, 6 DIFF_CAP LVD Operating Range VLVDOR 0.7 1.9 V DIFFSENSE Driver Output Voltage VDSO 1.2 1.4 V 7, 8 DIFFSENSE Driver Source Current IDSH 5 15 mA 7, 9, 11 DIFFSENSE Driver Sink Current IDSL 20 200 µA 7, 10, 11 MSTR/SLV Input Leakage I MSTRSLV -6.5 +125 µA ISO Input Leakage I ISO -125 +6.5 µA Thermal Shutdown 150 °C
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES VREF Line Regulation LI REG 1.0 2.0 % VREF Load Regulation LO REG 1.3 3.5 % VREF Current Limit I LIM 200 mA VREF Sink Current I SINK 200 mA NOTES: 1) Guaranteed by design. 2) All lines open. 3) ISO = 1 4) V OUT = 2.4V 5) V OUT = 0.4V 6) LVD pin only. 7) MSTR/SLV = 1 8) I DS = 0 to 5mA 9) V DSO = 0.0V 10) VDSO = 2.75V 11) TPWR = 5.5V 12) MCD is extended by the RC time constant formed by the resistor connected from DIFFSENSE to DIFF_CAP and the capacitor connected from DIFF_CAP to ground. 13) MSTR/SLV and ISO pins. 14) Terminator pins only. 15) DIFFCAP pin only.
PACKAGE INFORMATION
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/DallasPackInfo.)
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product. No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2006 Maxim Integrated Products • Printed USA The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation. PACKAGE INFORMATION (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/DallasPackInfo.)