DS2108 MAXIM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
FEATURES
/elevenoclock Fully compliant with SCSI, SCSI-2 and SCSI- 3 standards /elevenoclock Conforms to EIA RS-485 standard /elevenoclock Provides differential termination for 9 pairs of signal lines /elevenoclock Operates with SCSI signal voltages of -7 to +12 Volts /elevenoclock Laser-trimmed 330 and 150-ohm termination resistors have ±5% tolerance over full temperature range /elevenoclock Switchable power-down mode /elevenoclock Low power down capacitance of 6 pF /elevenoclock 24-pin plastic SOIC (DS2108S) PIN ASSIGNMENT
DESCRIPTION
The DS2108 SCSI Terminator has been specifically designed for High Voltage Differential (HVD) SCSI systems requiring switchable termination. The DS2108 integrates eighteen 330-ohm and nine 150-ohm precise switched termination resistors into a monolithic IC. The surface mount SOIC package saves board space over conventional resistor SIPs. The termination resistors can be isolated from the SCSI bus under software or hardware control. While in the powered down mode, the DS2108 isolates the nine terminator blocks from the bus while adding only 6 pF capacitance to each signal line of the SCSI bus. FUNCTIONAL DESCRIPTION The DS2108 consists of power-down circuitry, eighteen 330-ohm and nine 150-ohm termination resistors (Figure 1). The DS2108 can be removed from the circuit by bringing the power down pin (PD) low. The power down capacitance on the terminating resistors is 6 pF, well below the SCSI-3 allotment of 25 pF. The DS2108 supports SCSI signal voltages of -7 to +12 volts when powered on or off. When all lines settle into the quiescent state (no signal transitions), 56 mA is typically consumed. Only 1 mA is typically consumed in the powered down mode. DS2108 Differential SCSI Switchable Terminator www.dalsemi.com PD GND R1P R3P R4P R5P R6P R7P R8P R9P GND R2P TPWR R1N R2N R4N R5N R6N R7N R8N R9N TPWR NC R3N DS2108S 24-Pin SOIC (300-mil)
DS2108 BLOCK DIAGRAM Figure 1
TYPICAL DIFFERENTIAL SCSI BUS CONFIGURATION Figure 2 NOTES: 1. Two DS2108s required per 8–bit SCSI device and three DS2108s per 16–bit SCSI device. 2. Mid–bus termination effectively removed by grounding PD pin. 3. Termination power to be provided as specified in SCSI–3 Parallel Interface (SPI) document. 4. Local TERMPWR bypassing is recommended by the SPI document with values shown. The bypass capacitors should be located as close as possible to the DS2108s. Only one pair of capacitors is required per SCSI device (may be shared between DS2108s on same device). PIN DESCRIPTION Table 1 PIN SYMBOL DESCRIPTION 1, 11 TPWR Termination Power. Should be connected to the SCSI TERMPWR line. Bypass with a 2.2 µF cap in parallel with a 0.1 µF cap as shown in Figure 2, 3, 4, 5, 6, 7, 8, 9, 10 R1N…R9N Signal Termination Negative. Connect to –SIGNAL of SCSI bus. 12 NC No Connect. Do not connect any signal to this pin. 13, 23 GND Ground. Signal ground; 0.0V. 14, 15, 16, 17, 18, 19, 20, 21, 22 R1P…R9P Signal Termination Positive. Connect to +SIGNAL of SCSI bus. 24 PD Power Down. When tied low, the DS2108 enters a power-down mode. Contains an internal 50K pull-up. Strap low to deactivate the DS2108, leave open circuited to activate the DS2108.
ABSOLUTE MAXIMUM RATINGS* Voltage on Any Pin Relative to Ground -7.0V to +12.0V Operating Temperature 0 °C to 70°C Storage Temperature -55 °C to +125°C Soldering Temperature 260 °C for 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED OPERATING CONDITIONS (0°C to 70°C) PARAMETER SYM MIN TYP MAX UNITS NOTES TERMPWR Voltage V TP 4.00 5.25 V PD Active VPDA -0.3 0.8 V PD Inactive VPDI 2.00 V TP + 0.3 V DC CHARACTERISTICS PARAMETER SYMBOL MIN TYP MAX UNITS NOTES TERMPWR Current I TP 56 65 mA 1, 6 Power-down Current I PD 1 2 mA 1, 5 Command Mode Voltage Vem 7.0 12.0 V 7, 8 Termination Resistance R TTN 313.5 330 346.5 ohms 2 Termination Resistance R TNP 142.5 150 157.5 ohms 3 Termination Resistance R TPG 313.5 330 346.5 ohms 4 Power-down Termination Capacitance C PD 5 6 pF 1, 5, 7 NOTES: 1. 4.00V < TERMPWR < 5.25V 2. 330 Ω =resistor between TERMPWR and -SIGNAL. 3. 150 Ω =resistor between -SIGNAL and +SIGNAL. 4. 330 Ω =resistor between +SIGNAL and GDN. 5. PD = 0.0V. 6. Signal pins left open. 7. Guaranteed by design; not production tested. 8. Signal lines RxN and RxP only.
24-PIN SOIC (300-MIL) The chamfer on the body is optional. If it is not present, a terminal 1 identifier must be positioned so that ½ or more of its area is contained in the hatched zone. PKG 24-PIN DIM MIN MAX A IN. MM 0.094 2.38 0.105 2.68 A1 IN. MM 0.004 0.102 0.012 0.30 A2 IN. MM 0.089 2.26 0.095 2.41 b IN. MM 0.013 0.33 0.020 0.51 C IN. MM 0.009 0.229 0.013 0.33 D IN. MM 0.598 15.19 0.612 15.54 e IN. MM
0.050 BSC
1.27 BSC
E1 IN. MM 0.290 7.37 0.300 7.62 H IN. MM 0.398 10.11 0.416 10.57 L IN. MM 0.016 0.40 0.040 1.02 ΘΘΘΘ 0° 8°