DR22

DR22 CRYDOM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

DC Output DIN Rail Mount SSRs

• Output ratings up to 30 Amps at 200 VDC
• Integral heat sink eliminates the need for complex thermal calculations
• DBC substrate for superior thermal performance
• LED input status indicator
• IP20 touch-safe housing
• 1kHz Maximum PWM Frequency
• 3750 VAC optical isolation
• C-UL-US approved PRODUCT SELECTION Control Voltage 20 A 4-32 VDC DR2220D20U 30 A DR2220D30U AVAILABLE OPTIONS Required for valid part number Operating Voltage 20: 1-200 VDC Control Voltage D: 4-32 VDC Series DR22 20 D Rated Load Current 20: 20 Amps 30: 30 Amps U Terminal Layout U: Relay Configuration U20 OUTPUT SPECIFICATIONS (1) Description 30 A Absolute Maximum Rating [VDC] 200 Recommended Operating Voltage [VDC] 1-150 Maximum Off-State Leakage Current @ Rated Voltage [mA] 0.2 Load Current, DC General Use UL508 @ 40°C [ADC] 30 Minimum Load Current [mA] (2) 5 Maximum Surge Current [ADC] (10ms) 86 Maximum On-State Voltage Drop @ Rated Current [VDC] 0.480 Maximum On-State Resistance [RDS-ON][Ohms] 0.016 Maximum Pulse Width Modulation Frequency [Hz] (3) 900 20 A 200 1-150 0.1 Load Current, DC Motor Starting UL508 FLA @ 40°C [ADC] 5.44.1 0.680 0.034 1000 Motor Rating UL 508 [HP (kW)]: 120 VDC 1/2 (0.37)1/3 (0.25) INPUT SPECIFICATIONS (1)

Description

Minimum Turn-On Voltage (4) Must Turn-Off Voltage Minimum Input Current (for on-state) Maximum Input Current Nominal Input Impedance Maximum Turn-On Time [µsec] Maximum Turn-Off Time [µsec] DC Control 4-32 VDC -32 VDC

4 VDC

1 VDC

Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

GENERAL SPECIFICATIONS (1) ParametersDescription Dielectric Strength, Input to Output (50/60Hz) 3750 VRMS Dielectric Strength, Input/Output to Case (50/60Hz) 2500 VRMS Minimum Insulation Resistance (@ 500 VDC) 109 Ohms Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -40 to 80 °C Ambient Storage Temperature Range -40 to 100 °C Weight (typical) 10.5 oz (298 g) Housing Material UL94 V-0 Heat Sink Material Aluminum Din Rail Clip Material Zinc Plated Steel Hardware Finish Nickel Plating Input Terminal Screw Torque Range (in-lb/Nm) 13-15/1.5-1.7 Load Terminal Screw Torque Range (in-lb/Nm) 13-15/1.5-1.7 Humidity 95% non-condensing LED Input Status Indicator Green SURGE CURRENT INFORMATION Duty Factor 10% Duty Factor 20% Duty Factor 50% Period Pulse Width For Pulse Width Modulation applications select the curve according to the duty factor and pulse duration as follows: * for Single Surge Pulse Tc=40°C ;Tj=175°C ** for Repetitive Surge Pulse Tc=40°C ;Tj=130°C Duty Factor = Pulse Width Period x100 (%) Single Pulse * Duty Factor (10%) Duty Factor (20%) Duty Factor (50%) ** 100 125 150 0.1 1 10 100 1000 Surge Current (Amp) Surge Duration (msec) DR2220D20U 100 125 150 175 200 0.1 1 10 100 1000 Surge Current (Amp) Surge Duration (msec) DR2220D30U 0 5 10 15 20 25 30 35 4-32 VDC Input Input Current (mA) Input Voltage (VDC) INPUT CURRENT INFORMATION DatasheetDIN Rail Mount Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

EQUIVALENT CIRCUIT BLOCK DIAGRAMS/WIRING DIAGRAM Load can be wired in position A or B inductive loads must be diode suppressed. Trigger Circuit Control Circuit 4/A2 3/A1 DC V DCV Load Load A B Current Limiter Recommended Wire Sizes Terminal Configuration Wire Size (Solid / Stranded) Wire Pull-Out Strength (lb)[N] Output Relay “U” suffix Input Relay “U” suffix 2 x 18 AWG (1 mm 2) Stranded 2 x 10 AWG (6 mm 2) Stranded 2 x 18 AWG (1 mm 2) Stranded 2 x 12 AWG (4 mm 2) Stranded 20 [88] 60 [266] 20 [88] 40[177] THERMAL DERATE INFORMATION DR2220D30U 20 30 40 50 60 70 80 Load Current (Amps) Ambient Temperature (ºC) Single unit (5) Multiple units DR2220D20U Single unit (5) Multiple units 20 30 40 50 60 70 80 Load Current (Amps) Ambient Temperature (ºC) MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] INPUT+3/A1 -4/A2 OUTPUT+1 -2 0.39 [9.9] 1.88 [47.8] 3.67 [93.2]3.00 [76.2] 0.89 [22.5] 1.19 [30.2] 4.59 [116.5] 3.54 [90] Protective Earth Connection Protective Earth (PE) screw type recommended is 10-32 UNC standard not provided with SSR. Through the use of a DIN rail ground (protective conductor) terminal block, the DIN rail itself can be used as the grounding bus bar. In this case, the zinc plated steel material used for the DIN rail clip of DR22 models, permits a secure path to ground and avoid the need of a further PE connection. 10-32 Thread DatasheetDIN Rail Mount Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

Rev. 060216 AGENCY APPROVALS, CONFORMANCES AND EMC Certification in accordance with: United States Standard for Industrial Control Equipment - UL 508 and Canadian Standard Association for Industrial Control Equipment – C22.2 No. 14. Certification in accordance with: Electromagnetic Compatibility Generic Standard Inmunity Tests Test Specification Level IEC 61000-6-2 Immunity for Industrial Environments Electrostatic Discharge IEC 61000-4-2 Fast transients (burst) IEC 61000-4-4 Surge IEC 61000-4-5 4kV air discharge 4kV contact discharge Output 2kV, 5kHz, 100kHz Input 1kV, 5kHz, 100kHz 1kV Line to Line 2kV Line to Earth Performance Criterion A Criterion A Criterion B Criterion B Criterion B Criterion B Output E116949 (1) All parameters at 25°C unless otherwise specified. (2) Low current loads and high ambient temperature can affect turn-on time. (3) 8 VDC Minimum control voltage. Resistive loads only . Consider switching losses; at maximum frequency reduce to 75% output current. Recommended suppressor diode connected at load side, see wiring diagram. (4) Increase minimum voltage by 1 V for operations from -20 to -40°C. (5) Minimum spacing to obtain max. current is 22.5mm between adjacent units. GENERAL NOTES ID Marker Recommended Accessories CNLB CNLN CNL2 ACCESSORIES DatasheetDIN Rail Mount Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH.

• Disconnect all power before installing or working with this equipment.
• Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION.
• Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo.
• Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION
• Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil
• Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION.
• Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen
• Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSIONE.
• Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura
• Verificare tutti i collegamenti e sostituire tutte le coperture prima dell’accensione L'omissione di queste istruzioni provocherà la morte o lesioni serie 存在电击、 爆炸或电弧 闪烁危险
• 在操作此设 备之前请先 关闭电源。 若不遵守这些说明， 可能会导致严重的 人身伤害甚至死亡。 WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE
• The product's side panels may be hot, allow the product to cool before touching.
• Follow proper mounting instructions including torque values.
• Do not allow liquids or foreign objects to enter this product. Failure to follow these instructions can result in serious injury, or equipment damage. RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER
• Les panneaux latéraux du produit peuvent être chauds. Laisser le produit refroidir avant de le toucher.
• Respecter les consignes de montage, et notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, des lésions corporelles graves ou des dommages matériels. Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben. GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG
• Die Seitenwände können heiß sein. Lassen Sie das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder Fremdkörper in das Produkt ein. Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales. RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD
• Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en particular los pares de apretado.
• No dejar que penetren líquidos o cuerpos extraños en el producto. La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature. RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO
• I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo apparecchio. 如不能正确执行这些操作说明， 极有可能造成严重人体伤害或者设备的损坏。 材料损坏和高温外壳的危险性
• 产品的一侧面板可能很热，在其冷却前请 不要触碰。
• 遵照正确的安装说明，包括扭矩值。
• 请勿让液体及其他异物进入本产品。 DatasheetDIN Rail Mount Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

ANNEX - ENVIROMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium (Cr (VI)) biphenyls (PBB) diphenyl ethers (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 有毒有害物质或元素件部 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 DatasheetDIN Rail Mount Do not forget to visit us at: www.crydom.com Copyright © 2016 Crydom Inc. Specifications subject to change without notice.