DM2502_11 TI1 | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
DM2502,DM2503,DM2504 DM2502 DM2503 DM2504 Successive Approximation Registers Literature Number: SNOSBI9A
DM2502, DM2503, DM2504 Successive Approximation Registers November 1995 DM2502, DM2503, DM2504 Successive Approximation Registers General Description The DM2502, DM2503 and DM2504 are 8-bit and 12-bit TTL registers designed for use in successive approximation A/D converters. These devices contain all the logic and control circuits necessary in combination with a D/A con- verter to perform successive approximation analog-to-digital conversions. The DM2502 has 8 bits with serial capability and is not ex- pandable. The DM2503 has 8 bits and is expandable with- out serial capability. The DM2504 has 12 bits with serial capability and expandability. All three devices are available in ceramic DIP, ceramic flat- pak, and molded Epoxy-B DIPs. The DM2502, DM2503 and DM2504 operate over b55§Ct o a125§C; the DM2502C, DM2503C and DM2504C operate over 0 §Ct o a70§C.
Features
Y Complete logic for successive approximation A/D con- verters Y 8-bit and 12-bit registers Y Capable of short cycle or expanded operation Y Continuous or start-stop operation Y Compatible with D/A converters using any logic code Y Active low or active high logic outputs Y Use as general purpose serial-to-parallel converter or ring counter Logic Diagram Connection Diagrams (Dual-In-Line and Flat Packages) DM2502, DM2503 DM2504 TL/F/5702–1 Order Number DM2502J, DM2502CJ, DM2503J or DM2503CJ See NS Package J16A Order Number DM2502CN or DM2503CN See NS Package N16A Order Number DM2502W, DM2502CW, DM2503W, or DM2503CW See NS Package W16A Order Number DM2504F or DM2504CJ See NS Package F24D Order Number DM2504J or DM2504CJ See NS Package J24A Order Number DM2504CN See NS Package N24A C1995 National Semiconductor Corporation RRD-B30M115/Printed in U. S. A. Obsolete
Absolute Maximum Ratings (Note 1) Supply Voltage 7V Input Voltage 5.5V Output Voltage 5.5V Storage Temperature Range b65§Ct o a150§C Lead Temperature (Soldering, 10 seconds) 300 §C Operating Conditions Min Max Units Supply Voltage, V CC DM2502C, DM2503C, 4.75 5.25 V DM2504C DM2502, DM2503, 4.5 5.5 V DM2504 Temperature, T A DM2502C, DM2503C, 0 a70 §C DM2504C DM2502, DM2503 b55 a125 §C DM2504 Electrical Characteristics (Notes 2 and 3) V CCe5.0V, T Ae25§C, C Le15 pF, unless otherwise specified. Parameter Conditions Min Typ Max Units Logical ‘‘1’’ Input Voltage (V IH)V CCeMin 2.0 V Logical ‘‘1’’ Input Current (I IH)V CCeMax CP Input V IHe2.4V 6 40 mA D, E ,S Inputs VIHe2.4V 6 80 mA All Inputs VIHe5.5V 1.0 mA Logical ‘‘0’’ Input Voltage (V IL)V CCeMin 0.8 V Logical ‘‘0’’ Input Current (I IL)V CCeMax CP, S Inputs VILe0.4V b1.0 b1.6 mA D, E Inputs VILe0.4V b1.0 b3.2 mA Logical ‘‘1’’ Output Voltage (V OH)V CCeMin, I OHe0.48 mA 2.4 3.6 V Output Short Circuit Current VCCeMax; V OUTe0.0V; b10 b20 b45 mA (Note 4) (I OS) Output High; CP, D, S , High; E Low Logical ‘‘0’’ Output Voltage (V OL)V CCeMin, I OLe9.6 mA 0.2 0.4 V Supply Current (I CC)V CCeMax, All Outputs Low DM2502C 65 95 mA DM2502 65 85 mA DM2503C 60 90 mA DM2503 60 80 mA DM2504C 90 124 mA DM2504 90 110 mA Propagation Delay to a Logical ‘‘0’’ 10 18 28 ns From CP to Any Output (t pd0) Propagation Delay to a Logical ‘‘0’’ CP High, S Low 16 24 ns From E to Q7 (Q11) Output (t pd0) DM2503, DM2503C, DM2504, DM2504C Only Propagation Delay to a Logical ‘‘1’’ 10 26 38 ns From CP to Any Output (t pd1) Propagation Delay to a Logical ‘‘1’’ CP High, S Low 13 19 ns From E to Q7 (Q11) Output (t pd1) DM2503, DM2503C, DM2504, DM2504C Only Set-Up Time Data Input (t s(D)) b10 4 8 ns Set-Up Time Start Input (t s(S)0 9 16 ns Minimum Low CP Width (t PWL)3 0 42 ns Minimum High CP Width (t PWH)1 7 24 ns Maximum Clock Frequency (f MAX) 15 21 MHz Note 1: ‘‘Absolute Maximum Ratings’’ are those values beyond which the safety of the device cannot be guaranteed. Except for ‘‘Operating Temperature Range’’ they are not meant to imply that the devices should be operated at these limits. The table of ‘‘Electrical Characteristics’’ provides conditions for actual device operation. Note 2: Unless otherwise specified min/max limits apply across the b55§Ct o a125§C temperature range for the DM2502, DM2503 and DM2504, and across the 0§Ct o a70§C range for the DM2502C, DM2503C and DM2504C. All typicals are given for V CCe5.0V and T Ae25§C. Note 3: All currents into device pins shown as positive, out of device pins as negative, all voltages referenced to ground unless otherwise noted. All values shown as max or min on absolute value basis. Note 4: Only one output at a time should be shorted. Obsolete
Application Information
The registers consist of a set of master latches that act as the control elements in the device and change state on the input clock high-to-low transition and a set of slave latches that hold the register data and change on the input clock low-to-high transition. Externally the device acts as a special purpose serial-to-parallel converter that accepts data at the D input of the register and sends the data to the appropriate slave latch to appear at the register output and the DO out- put on the DM2502 and DM2504 when the clock goes from low-to-high. There are no restrictions on the data input; it can change state at any time except during a short interval centered about the clock low-to-high transition. At the same time that data enters the register bit the next less significant bit register is set to a low ready for the next iteration. The register is reset by holding the S (Start) signal low dur- ing the clock low-to-high transition. The register synchro- nously resets to the state Q7 (11) low, and all the remaining register outputs high. The Q CC (Conversion Complete) sig- nal is also set high at this time. The S signal should not be brought back high until after the clock low-to-high transition in order to guarantee correct resetting. After the clock has gone high resetting the register, the S signal must be re- moved. On the next clock low-to-high transition the data on the D input is set into the Q7 (11) register bit and the Q6 (10) register bit is set to a low ready for the next clock cycle. On the next clock low-to-high transition data enters the Q6 (10) register bit and Q5 (9) is set to a low. This operation is repeated for each register bit in turn until the register has been filled. When the data goes into Q0, the Q CC signal goes low, and the register is inhibited from further change until reset by a Start signal. The DM2502, DM2503 and DM2504 have a specially tai- lored two-phase clock generator to provide nonoverlapping two-phase clock pulses (i.e., the clock waveforms intersect below the thresholds of the gates they drive). Thus, even at very slow dV/dt rates at the clock input (such as from rela- tively weak comparator outputs), improper logic operation will not result. LOGIC CODES All three registers can be operated with various logic codes. Two’s complement code is used by offsetting the compara- tor (/2 full range a (/2 LSB and using the complement of the MSB (Q7 or Q 11) with a binary D/A converter. Offset binary is used in the same manner but with the MSB (Q 7o rQ 11). BCD D/A converters can be used with the addition of illegal code suppression logic. ACTIVE HIGH OR ACTIVE LOW LOGIC The register can be used with either D/A converters that require a low voltage level to turn on, or D/A converters that require a high voltage level to turn the switch on. If D/A converters are used which turn on with a low logic level, the resulting digital output from the register is active low. That is, a logic ‘‘1’’ is represented as a low voltage level. If D/A converters are used that turn on with a high logic level then the digital output is active high; a logic ‘‘1’’ is represented as a high voltage level. EXPANDED OPERATION An active low enable input, E , on the DM2503 and DM2504 allows registers to be connected together to form a longer register by connecting the clock, D, and S inputs in parallel and connecting the Q CC output of one register to the E input of the next less significant register. When the start resets the register, the E signal goes high, forcing the Q7 (11) bit high and inhibiting the register from accepting data until the previous register is full and its Q CC goes low. If only one register is used the E input should be held at a low logic level. Timing Diagram DM2502, DM2503 TL/F/5702–2 Obsolete
Application Information (Continued) SHORT CYCLE If all bits are not required, the register may be truncated and conversion time saved by using a register output going low rather then the Q CC signal to indicate the end of conversion. If the register is truncated and operated in the continuous conversion mode, a lock-up condition may occur on power turn-on. This condition can be avoided by making the start input the OR function of Q CC and the appropriate register output. COMPARATOR BIAS To minimize the digital error below g(/2 LSB, the compara- tor must be biased. If a D/A converter is used which re- quires a low voltage level to turn on, the comparator should be biased a(/2 LSB. If the D/A converter requires a high logic level to turn on, the comparator must be biased b(/2 LSB. Definition of Terms CP: The clock input of the register. D: The serial data input of the register. DO: The serial data out. (The D input delayed one bit). E: The register enable. This input is used to expand the length of the register and when high forces the Q7 (11) register output high and inhibits conversion. When not used for expansion the enable is held at a low logic level (ground). Q i ie7 (11) to 0: The outputs of the register. QCC: The conversion complete output. This output remains high during a conversion and goes low when a conversion is complete. Q7 (11): The true output of the MSB of the register. Q7 (11): The complement output of the MSB of the register. S: The start input. If the start input is held low for at least a clock period the register will be reset to Q7 (11) low and all the remaining outputs high. A start pulse that is low for a shorter period of time can be used if it meets the set-up time requirements of the S input. Truth Table DM2502, DM2503 Time Inputs Outputs1 tn DS E2 D03 Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 Q CC
0 X L LX XXXXXXXX X
1 D 7 H L X LHHHHHHH H
2 D 6 H L D 7 D 7 LHHHHHH H
3 D 5 H L D 6 D 7 D 6 LHHHHH H
4 D 4 H L D 5 D 7 D 6 D 5 LHHHH H
5 D 3 H L D 4 D 7D 6D 5D 4 L H H H H
6 D 2 H L D 3 D 7D 6D 5D 4D 3 L H H H
7 D 1 H L D 2 D 7D 6D 5D 4D 3D 2 L H H
8 D 0 H L D 1 D 7D 6D 5D 4D 3D 2D 1 L H
9 X H L D0 D7 D6 D5 D4 D3 D2 D1 D0 L
10 X X L X D7 D6 D5 D4 D3 D2 D1 D0 L
X X H X H N CN CN CN CN CN CN C N C H e High Voltage LevelNote 1: Truth table for DM2504 is extended to include 12 outputs. L e Low Voltage LevelNote 2: Truth table for DM2502 does not include E column or last line in truth table shown. X e Don’t CareNote 3: Truth table for DM2503 does not include D0 column. NC e No Change Typical Applications BCD Illegal Code Suppression Active High Active Low TL/F/5702–3 Obsolete
Typical Applications (Continued) Fast Precision Analog-to-Digital Converter INPUT RANGES Equiv. Unipolar Bipolar Connect DAC Z OUT 0t o1 0 g5 Input to A 2.36 k X 0t o5 g2.5 Input to A 1.90 k X 0t o2 0 g10 Input to B 3.08 k X B to DAC OUT Switching Time Waveforms TL/F/5702–4 TL/F/5702–5 Obsolete
Physical Dimensions inches (millimeters) Order Number DM2504F or DM2504CF Order Number DM2502J, DM2502CJ, DM2503J or DM2503CJ Obsolete
Physical Dimensions inches (millimeters) (Continued) Order Number DM2504J or DM2504CJ Order Number DM2502CM or DM2503CN Obsolete
DM2502, DM2503, DM2504 Successive Approximation Registers Physical Dimensions inches (millimeters) (Continued) Order Number DM2504CN Order Number DM2502W, DM2502CW, DM2503W, or DM2503CW LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or 2. A critical component is any component of a life systems which, (a) are intended for surgical implant support device or system whose failure to perform can into the body, or (b) support or sustain life, and whose be reasonably expected to cause the failure of the life failure to perform, when properly used in accordance support device or system, or to affect its safety or with instructions for use provided in the labeling, can effectiveness. be reasonably expected to result in a significant injury to the user. National Semiconductor National Semiconductor National Semiconductor National Semiconductor Corporation Europe Hong Kong Ltd. Japan Ltd.
1111 West Bardin Road Fax: ( a49) 0-180-530 85 86 13th Floor, Straight Block, Tel: 81-043-299-2309
Arlington, TX 76017 Email: cnjwge @ tevm2.nsc.com Ocean Centre, 5 Canton Rd. Fax: 81-043-299-2408 Tel: 1(800) 272-9959 Deutsch Tel: ( a49) 0-180-530 85 85 Tsimshatsui, Kowloon Fax: 1(800) 737-7018 English Tel: ( a49) 0-180-532 78 32 Hong Kong Fran3ais Tel: ( a49) 0-180-532 93 58 Tel: (852) 2737-1600 Italiano Tel: ( a49) 0-180-534 16 80 Fax: (852) 2736-9960 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. Obsolete
Texas InstrumentsIncorporatedand itssubsidiaries(TI)reservetherighttomake corrections,modifications,enhancements,improvements, and otherchanges toitsproductsand servicesatany timeand todiscontinueany productorservicewithoutnotice.Customersshould obtainthelatestrelevantinformationbeforeplacingordersand shouldverifythatsuch informationiscurrentand complete.Allproductsare soldsubjecttoTI’s termsand conditionsofsalesuppliedatthetimeoforderacknowledgment. TIwarrantsperformanceofitshardwareproductstothespecificationsapplicableatthetimeofsaleinaccordancewithTI’s standard warranty.Testingand otherqualitycontroltechniquesareused totheextentTIdeems necessarytosupportthiswarranty.Exceptwhere mandated by governmentrequirements,testingofallparametersofeach productisnotnecessarilyperformed. TIassumes no liabilityforapplicationsassistanceorcustomerproductdesign.Customersareresponsiblefortheirproductsand applicationsusingTIcomponents.To minimizetherisksassociatedwithcustomerproductsand applications,customersshouldprovide adequatedesignand operatingsafeguards. TIdoes notwarrantorrepresentthatany license,eitherexpressorimplied,isgrantedunderany TIpatentright,copyright,mask work right, orotherTIintellectualpropertyrightrelatingtoany combination,machine,orprocessinwhichTIproductsorservicesareused.Information publishedby TIregardingthird-partyproductsorservicesdoes notconstitutea licensefromTItouse such productsorservicesora warrantyorendorsementthereof.Use ofsuch informationmay requirea licensefroma thirdpartyunderthepatentsorotherintellectual propertyofthethirdparty,ora licensefromTIunderthepatentsorotherintellectualpropertyofTI. ReproductionofTIinformationinTIdatabooks ordatasheetsispermissibleonlyifreproductioniswithoutalterationand isaccompanied by allassociatedwarranties,conditions,limitations,and notices.Reproductionofthisinformationwithalterationisan unfairand deceptive businesspractice.TIisnotresponsibleorliableforsuch altereddocumentation.Informationofthirdpartiesmay be subjecttoadditional restrictions. ResaleofTIproductsorserviceswithstatementsdifferentfromorbeyond theparametersstatedby TIforthatproductorservicevoidsall expressand any impliedwarrantiesfortheassociatedTIproductorserviceand isan unfairand deceptivebusinesspractice.TIisnot responsibleorliableforany such statements. TIproductsarenotauthorizedforuse insafety-criticalapplications(suchas lifesupport)where a failureoftheTIproductwouldreasonably be expectedtocause severepersonalinjuryordeath,unlessofficersofthepartieshave executedan agreementspecificallygoverning such use.Buyersrepresentthattheyhave allnecessaryexpertiseinthesafetyand regulatoryramificationsoftheirapplications,and acknowledgeand agreethattheyaresolelyresponsibleforalllegal,regulatoryand safety-relatedrequirementsconcerningtheirproducts and any use ofTIproductsinsuch safety-criticalapplications,notwithstandingany applications-relatedinformationorsupportthatmay be providedby TI.Further,Buyersmust fullyindemnifyTIand itsrepresentativesagainstany damages arisingoutoftheuse ofTIproductsin such safety-criticalapplications. TIproductsareneitherdesignednorintendedforuse inmilitary/aerospaceapplicationsorenvironmentsunlesstheTIproductsare specificallydesignatedby TIas military-gradeor"enhanced plastic." Onlyproductsdesignatedby TIas military-grademeet military specifications.Buyersacknowledgeand agreethatany such use ofTIproductswhichTIhas notdesignatedas military-gradeissolelyat theBuyer's risk,and thattheyaresolelyresponsibleforcompliancewithalllegaland regulatoryrequirementsinconnectionwithsuch use. TIproductsareneitherdesignednorintendedforuse inautomotiveapplicationsorenvironmentsunlessthespecificTIproductsare designatedby TIas compliantwithISO/TS 16949 requirements.Buyersacknowledgeand agreethat,iftheyuse any non-designated productsinautomotiveapplications,TIwillnotbe responsibleforany failuretomeet such requirements. FollowingareURLs where you can obtaininformationon otherTexas Instrumentsproductsand applicationsolutions: Products Applications Audio www.ti.com/audio Communicationsand Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP ® Products www.dlp.com Energyand Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocksand Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space,Avionicsand Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportationand Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Videoand Imaging www.ti.com/video RFID www.ti-rfid.com OMAP MobileProcessors www.ti.com/omap WirelessConnectivity www.ti.com/wirelessconnectivity TIE2E Community Home Page e2e.ti.com MailingAddress:Texas Instruments,PostOfficeBox 655303,Dallas,Texas 75265 Copyright© 2011,Texas InstrumentsIncorporated