DG506A_10 MAXIM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
Features
S Pin Compatible with Harris, Siliconix, Intersil S Operable with ±4.5V to ±18V Supplies S Symmetrical, Bidirectional Operation S Logic and Enable Inputs, TTL and CMOS Compatible S Latch-Up Proof Construction S Monolithic, Low-Power CMOS Design 19-0482; Rev 3; 2/10 Pin Configurations Typical Operating Circuit
Ordering Information
†Devices are available in a lead(Pb)-free/RoHS-compliant package, specify lead-free by adding “+” to the part number when ordering. CLOCK IN QB QC QAAH1 BH1 NC +15V +15V GNDr02r01 QD NC ANALOG INPUT (OUTPUTS) -15V -15V ANALOG OUTPUT (INPUTS) ENABLE IN (MUX ON-OFF CONTROL) A
0 A1 A2
8-CHANNEL SEQUENTIAL DIFFERENTIAL MUX/DEMUX D V EN NC GND S10 S11 S12 S13 S14 S15 S16 NC NC V+ 28 D a S8a S7a S6a S5a S4a S3a S2a S1a EN NC NC GND S1b S2b S3b S4b S5b S6b S7b S8b NC Db DG506A DG507A PART† TEMP RANGE PIN-PACKAGE DG506AAK -55°C to +125°C 28 CERDIP DG506ABK -25°C to +85°C 28 CERDIP DG506AC/D 0°C to +70°C Dice DG506ACJ 0°C to +70°C 28 Plastic Dip DG506ACK 0°C to +70°C 28 CERDIP DG506ACWI 0°C to +70°C 28 Wide SO DG506AMWI/PR -55°C to +125°C 28 Wide SO DG507AAK -55°C to +125°C 28 CERDIP DG507ABK -25°C to +85°C 28 CERDIP DG507AC/D 0°C to +70°C Dice DG507ACJ 0°C to +70°C 28 Plastic DIP DG507ACK 0°C to +70°C 28 CERDIP DG507ACWI 0°C to +70°C 28 Wide SO
Monolithic CMOS Analog MultiplexersDG506A/DG507A Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. (Voltages referenced to V-.) 20mA, whichever occurs first Peak Current, S or D (pulsed at 1ms, 10% duty cycle max) ...40mA Continuous Power Dissipation (TA = +70°C)* 28-Pin Ceramic DIP (derate 16.7mW/NC above +70NC) ..1333mW 28-Pin Plastic DIP (derate 14.3mW/NC above +70NC) ...1143mW 28-Pin Wide SO (derate 12.5mW/°C above +70°C) ..1000mW
ELECTRICAL CHARACTERISTICS
(V+ = 15V, V- = -15V, V GND = 0V, TA = +25NC, unless otherwise indicated.) ABSOLUTE MAXIMUM RATINGS *All leads soldered or welded to PCB. PARAMETER SYMBOL CONDITIONS DG506AA DG507AA DG506AB/C DG507AB/C UNITS MIN (Note 2) TYP (Note 3) MAX MIN (Note 2) TYP (Note 3) MAX SWITCH Analog Signal Range VANALOG -15 +15 -15 +15 V Drain-to- Source On-Resistance RDS(ON) Sequence each switch on, VAL = 0.8V, VAH = 2.4V, VEN = 2.4V VD = 10V, IS = -200FA 270 400 270 450 I VD = -10V, IS = -200FA 230 400 230 450 Greatest Change in Drain-Source On-Resistance Between Channels RDS(ON) DS(ON)MAX DS(ON)MIN DS(ON) DS(ON)AVE R R R R − -10V P VS P +10V 6 6 % Source Off- Leakage Current IS(OFF) VEN = 0.8V, VAL = 0.8V VS = 10V, VD = -10V -1 0.002 +1 -5 0.002 +5 nA VS = -10V, Drain Off- Leakage Current ID(OFF) DG506A, VEN = 0.8V, VAL = 0.8V VD = 10V, VS = -10V -10 0.02 +10 -20 0.02 +20 nA VD = -10V, VS = 10V -10 -0.03 +10 -20 -0.03 +20 DG507A, VEN = 0.8V, VAL = 0.8V VD = 10V, VS = -10V -5 0.007 +5 -10 0.007 +10 VD = -10V, VS = 10V -5 -0.015 +5 -10 -0.015 +10
Monolithic CMOS Analog Multiplexers DG506A/DG507A ELECTRICAL CHARACTERISTICS (continued) (V+ = 15V, V- = -15V, V GND = 0V, TA = +25NC, unless otherwise indicated.) PARAMETER SYMBOL CONDITIONS DG506AA DG507AA DG506AB/C DG507AB/C UNITS MIN (Note 2) TYP (Note 3) MAX MIN (Note 2) TYP (Note 3) MAX Channel On-Leakage Current ID(ON) (Note 4) DG506A, sequence each switch on, VAL = 0.8V, VAH = 2.4V, VEN = 2.4V VS(all) = VD = 10V -10 0.03 +10 -20 0.03 +20 nA VS(all) = VD DG507A, sequence each switch on, VAL = 0.8V, VAH = 2.4V, VEN = 2.4V VS(all) = VD = 10V -5 0.015 +5 -10 0.015 +10 VS(all) = VD INPUT Address Input Current, Input- Voltage High IAH FA VA = 15V 0.006 10 0.006 10 Address Input Current, Input- Voltage Low IAL All VA = 0V VEN = 2.4V -10 -0.002 -10 -0.002 FA VEN = 0V -10 -0.002 -10 -0.002 DYNAMIC Switching Time of Multiplexer ttransition Figure 1 0.6 1 0.06 Fs Break-Before- Make Interval tOPEN Figure 3 0.2 0.2 Fs Enable Turn- On Time tON(EN) Figure 2 1 1 Fs Enable Turn- Off Time tOFF(EN) Figure 2 0.4 0.4 Fs Off-Isolation (Note 5) OIRR VEN = 0V, RL = 1kI, CL = 15pF, VS = 7VRMS, f = 500kHz 68 68 dB Source Off- Capacitance CS(OFF) VEN = 0V, f = 140kHz, V S = 0V 6 6 pF Drain Off- Capacitance CD(OFF) VEN = 0V, f = 140kHz DG506A, VD = 0V 45 45 pFDG507A, VD = 0V 23 23 SUPPLY Positive Supply Current I+ VEN = 0 or 5V, all V A = 0V 0.13 0.25 0.13 0.3 mA Negative Supply Current I- VEN = 0 or 5V, all V A = 0V -0.15 -0.07 -0.25 -0.07
Monolithic CMOS Analog MultiplexersDG506A/DG507A ELECTRICAL CHARACTERISTICS (Overtemperature) (V+ = 15V, V- = -15V, V GND = 0V, TA = overtemperature range, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS DG506AA DG507AA DG506AB/C DG507AB/C UNITS MIN (Note 2) TYP (Note 3) MAX MIN (Note 2) TYP (Note 3) MAX SWITCH Analog Signal Range VANALOG -15 +15 -15 +15 V Drain-to-Source On-Resistance RDS(ON) Sequence each switch on, VAL = 0.8V, VAH = 2.4V, VEN = 2.4V VD = 10V, IS = -200FA 500 550 I VD = -10V, IS = -200FA 500 550 Source Off- Leakage Current IS(OFF) VEN = 0.8V, VAL = 0.8V VS = 10V, VD = -10V -50 +50 -50 +50 nA VS = -10V, VD = 10V -50 +50 -50 +50 Drain Off- Leakage Current ID(OFF) DG506A, VEN = 0.8V, VAL = 0.8V VD = 10V, VS = -10V -300 +300 -300 +300 nA VD = -10V, VS = 10V -300 +300 -300 +300 DG507A, VEN = 0.8V, VAL = 0.8V VD = 10V, VS = -10V -200 +200 -200 +200 VD = -10V, VS = 10V -200 +200 -200 +200 Channel On-Leakage Current ID(ON) (Note 4) DG506A, sequence each switch on, VAL = 0.8V, VAN = 2.4V, VEN = 2.4V VS(all) = VD = 10V -300 +300 -300 +300 nA VS(all) = VD = -10V -300 +300 -300 +300 DG507A, sequence each switch on, VAL = 0.8V, VAN = 2.4V, VEN = 2.4V VS(all) = VD = 10V -200 +200 -200 +200 VS(all) = VD = -10V -200 +200 -200 +200 INPUT Address Input Current, Input- Voltage High IAH VA = 2.4V -30 -30 FA VA = 15V 30 30 Address Input Current, Input- Voltage Low IAL All VA = 0V VEN = 2.4V -30 -30 FA VEN = 0V 30 30
Monolithic CMOS Analog Multiplexers DG506A/DG507A ELECTRICAL CHARACTERISTICS (Overtemperature) (continued) (V+ = 15V, V- = -15V, V GND = 0V, TA = over temperature range, unless otherwise noted.) Note 1: Signals on SX, DX, or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. Note 2: The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. Note 3: Typical values are for design aid only, not guaranteed nor subject to production testing. Note 4: ID(ON) is leakage from driver into on switch. Note 5: Off-isolation = 20log x VO/VS, VS = input to off switch, V D = output due to VS. Truth Tables Switching Time Test Circuits Figure 1a. Transition Switching Time Figure 1b. Transition Switching Time Note: Logic “0” = VAL ≤ 0.8V, Logic “1” = VAH ≥ 2.4V, “0” = Don’t Care. +2.4V ±10VS1 ±10VS16A1 EN +15V -15V DG506A GND SWITCH OUTPUT V O 1MΩ D 50Ω LOGIC INPUT S2 THRU S15 35pF +2.4V ±10VS1b ±10VS8bA1 EN +15V -15V DG507A GND SWITCH OUTPUT V O 1MΩ Db 50Ω LOGIC INPUT S2b, AND S7b S1a THRU S8a, Da 35pF A3 A2 A1 A0 EN ON SWITCH X X X X 0 None 0 0 0 0 1 1 0 0 0 1 1 2 0 0 1 0 1 3 0 0 1 1 1 4 0 1 0 0 1 5 0 1 0 1 1 6 0 1 1 0 1 7 0 1 1 1 1 8 1 0 0 0 1 9 1 0 0 1 1 10 1 0 1 0 1 11 1 0 1 1 1 12 1 1 0 0 1 13 1 1 0 1 1 14 1 1 1 0 1 15 1 1 1 1 1 16 A2 A1 A0 EN ON SWITCH X X X 0 None 0 0 0 1 1 0 0 1 1 2 0 1 0 1 3 0 1 1 1 4 1 0 0 1 5 1 0 1 1 6 1 1 0 1 7 1 1 1 1 8
Monolithic CMOS Analog MultiplexersDG506A/DG507A Switching Time Test Circuits (continued) Figure 2a. Enable Switching Time Figure 2b. Enable Switching Time Figure 3. Break-Before-Make Figure 4. Timing Diagrams for Figures 1, 2, and 3
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix number, but the drawing pertains to the package regardless of RoHS status. -5VS1 EN +15V -15V DG506A GND SWITCH OUTPUT VO 1kΩ D 50Ω LOGIC INPUT S2 THRU S16 35pF -5VS1b EN +15V -15V DG507A GND SWITCH OUTPUT V O 1kΩ 35pF Db 50Ω LOGIC INPUT S1a THRU S4a, Da, S2b, S3b, S4b +2.4V VS = +5VALL S AND Da A0 A1 A2 A3 EN +15V -15V DG506A DG507A GND SWITCH OUTPUT V O 1kΩ Db, D 50Ω LOGIC INPUT 35pF LOGIC INPUT t r < 20ns ti < 20ns SWITCH OUTPUT VO (SEE FIGURE 1) TRANSITION TIME SWITCH OUTPUT VO (SEE FIGURE 2) ENABLE t(ON)/t(OFF) TIME SWITCH OUTPUT VO (SEE FIGURE 3) 50% tON (En) 0.1 VO 0.9 VO VO VS VS 50% S8 ON toff (En) VS1
0.8 VS1
0.8 VS8
t OPEN PACKAGE TYPE PACKAGE CODE DOCUMENT NO.
28 CERDIP J28-2 21-0046
28 Plastic DIP P28-2 21-0044
28 Wide SO W28-5 21-0042
Monolithic CMOS Analog Multiplexers DG506A/DG507A Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 7 © 2010 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.
Revision History
0 8/92 Initial release — 1 1/99 Updated to Word format. 1–7 2 5/09 Added ruggedized plastic part. 1–4, 7 3 2/10
- Added lead temperature to the Absolute Maximum Ratings.
- Changed the derate rate of all packages to above 70°C in the Absolute Maximum Ratings.