DG401 INTERSIL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 9

Technical content

Features

  • Fast Switching Action
  • Low Charge Injection
  • DG401 Dual SPST; Same Pinout as HI-5041
  • DG403 Dual SPDT; DG190, IH5043, IH5151, HI-5051
  • DG405 Dual DPST; DG184, HI-5045, IH5145
  • TTL, CMOS Compatible
  • Single or Split Supply Operation

Applications

  • Audio Switching
  • Battery Operated Systems
  • Data Acquisition
  • Hi-Rel Systems
  • Sample and Hold Circuits
  • Communication Systems
  • Automatic Test Equipment D 1 NC NC NC NC NC D NC GND V L IN IN1 D 1 NC D 3 D 4 D 2 NC GND VL IN2 IN1

Ordering Information

TEMP. RANGE (oC) PACKAGE PKG. NO. DG401DJ -40 to 85 16 Ld PDIP E16.3 DG401DY -40 to 85 16 Ld SOIC M16.15 DG403DJ -40 to 85 16 Ld PDIP E16.3 DG403DY -40 to 85 16 Ld SOIC M16.15 DG405DY -40 to 85 16 Ld SOIC M16.15 TRUTH TABLE LOGIC DG401 DG403 DG405 SWITCH SWITCH 1, 2 SWITCH 3, 4 SWITCH

0 OFF OFF ON OFF

1 ON ON OFF ON

NOTE: Logic “0”≤0.8V. Logic “1”≥2.4V. Data Sheet June 1999

SWITCHES SHOWN FOR LOGIC “1” INPUT 1S1 IN1 IN2 D 1 D 2 VL V+ GND V- 12 11 13 14 IN1 IN2 D 1 D 3 D 2 D 4 VL V+ GND V- 12 11 13 14 IN1 IN2 D 1 D 3 D 2 D 4 VL V+ GND V- 12 11 13 14 VL VIN GND DRAIN SOURCE DG401, DG403, DG405

Absolute Maximum Ratings Thermal Information V Whichever Occurs First Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle, Max) . . 100mA Operating Conditions Thermal Resistance (Typical, Note 2) θ JA (oC/W) (SOIC - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationo ft h e device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Signals on SX , DX , or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. 2. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical SpecificationsTest Conditions: V+ = +15V, V- = -15V, VIN = 2.4V, 0.8V (Note 3), VL = 5V, Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP (oC) (NOTE 4) MIN (NOTE 5) TYP (NOTE 4) MAX UNITS DYNAMIC CHARACTERISTICS Turn-ON Time, t ON R L = 300Ω , CL = 35pF 25 - 100 150 ns Turn-OFF Time, tOFF 25 - 60 100 ns Break-Before-Make Time Delay (DG403), tD R L = 300Ω , CL = 35pF 25 5 12 - ns Charge Injection, Q (Figure 3) C L = 10nF, VG = 0V, RG = 0Ω 25 - 60 - pC OFF Isolation (Figure 4) R L = 100Ω , CL = 5pF, f = 1MHz 25 - 72 - dB Crosstalk (Channel-to-Channel) (Figure 6) 25 - -90 - dB Source OFF Capacitance, C S(OFF) f = 1MHz, VS = VD = 0V (Figure 7) 25 - 12 - pF Drain OFF Capacitance, CD(OFF) 25 - 12 - pF Channel ON Capacitance, CD(ON) + CS(ON) 25 - 39 - pF DIGITAL INPUT CHARACTERISTICS Input Current with V IN Low, IIL VINUnder Test = 0.8V, All Others = 2.4V Full -1 0.005 1 µA Input Current with VIN High, IIH VINUnder Test = 2.4V, All Others = 0.8V Full -1 0.005 1 µA ANALOG SWITCH CHARACTERISTICS Analog Signal Range, V ANALOG Full -15 - 15 V Drain-Source ON Resistance, rDS(ON) V+ = 13.5V, V- = -13.5V, IS = 10mA, V D =±10V 25 - 20 45 Ω Full - - 55 Ω rDS(ON) Matching Between Channels,ΔrDS(ON) V+ = 16.5V, V- = -16.5V, IS = -10mA, VD = 5, 0, -5V 25 - 3 3 Ω Full - - 5 Ω Source OFF Leakage Current, IS(OFF) V+ = 16.5V, V- = -16.5 VD =±15.5V, VS = 15.5V 25 -0.5 -0.01 0.5 nA Full -5 - 5 nA Drain OFF Leakage Current, ID(OFF) 25 -0.5 -0.01 0.5 nA Full -5 - 5 nA Channel ON Leakage Current, ID(ON) +IS(ON) V± =±16.5V, VD = VS =±15.5V 25 -1 -0.04 1 nA Full -10 - 10 nA DG401, DG403, DG405