DEB MURATA | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 23
Technical content
(High voltage ceramic capacitor of Class 2) Rated voltage : DC2kV / DC3.15kV Reference Specification Product specifications in this catalog are as of Aug.2015, and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering.Please read rating and Cautions first.
- OPERATING VOLTAGE When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage containing these irregular voltage. When DC-rated capacitors are to be used in input circuits from commercial power source (AC filter), be sure to use Safety Recognized Capacitors because various regulations on withstand voltage or impulse withstand established for each equipment should be taken into considerations. Voltage DC Voltage DC+AC Voltage AC Voltage Pulse Voltage(1) Pulse Voltage(2) Positional Measurement 2. OPERATING TEMPERATURE AND SELF-GENERATED HEAT Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self- generated heat due to dielectric-loss. The allowable frequency should be in less than 300kHz in sine wave. Applied voltage should be the load such as self-generated heat is within 20 C on the condition of atmosphere temperature 25 C. When measuring, use a thermocouple of small thermal capacity-K of 0.1mm and be in the condition where capacitor is not affected by radiant heat of other components and wind of surroundings. While, in case of non-sine wave which include a harmonic frequency, please contact our sales representatives or product engineers. 3. FAIL-SAFE When capacitor would be broken, failure may result in a short circuit. Be sure to provide an appropriate fail-safe function like a fuse on your product if failure would follow an electric shock, fire or fume. 4. VIBRATION AND IMPACT Do not expose a capacitor or its leads to excessive shock or vibration during use. 5. SOLDERING When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. When soldering capacitor with a soldering iron, it should be performed in following conditions. Temperature of iron tip : 400 C max. Soldering iron wattage : 50W max. Soldering time : 3.5 s max. Vp-p Vp-pVp-pVo-p Vo-p
- BONDING, RESIN MOLDING AND COATING In case of bonding, molding or coating this product, verify that these processes do not affect the quality of capacitor by testing the performance of the bonded, molded or coated product in the intended equipment. In case of the amount of applications, dryness / hardening conditions of adhesives and molding resins containing organic solvents (ethyl acetate, methyl ethyl ketone, toluene, etc.) are unsuitable, the outer coating resin of a capacitor is damaged by the organic solvents and it may result, worst case, in a short circuit. The variation in thickness of adhesive, molding resin or coating may cause a outer coating resin cracking and/or ceramic element cracking of a capacitor in a temperature cycling. 7. TREATMENT AFTER BONDING, RESIN MOLDING AND COATING When the outer coating is hot (over 100 ℃) after soldering, it becomes soft and fragile. So please be careful not to give it mechanical stress. Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. 8. OPERATING AND STORAGE ENVIRONMENT The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify that these processes do not affect product quality by testing the performance of a cleaned, bonded or molded product in the intended equipment. Store the capacitors where the temperature and relative humidity do not exceed -10 to 40 C and 15 to 85%. Use capacitors within 6 months after delivered. Check the solderability after 6 months or more. 9. LIMITATION OF APPLICATIONS Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party’s life, body or property. 1. Aircraft equipment 2. Aerospace equipment 3. Undersea equipment 4. Power plant control equipment 5. Medical equipment 6. Transportation equipment (vehicles, trains, ships, etc.) 7. Traffic signal equipment 8. Disaster prevention / crime prevention equipment 9. Data-processing equipment exerting influence on public 10. Application of similar complexity and/or reliability requirements to the applications listed in the above.
- CLEANING (ULTRASONIC CLEANING) To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity : Output of 20 watts per liter or less. Rinsing time : 5 min maximum. Do not vibrate the PCB/PWB directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires. 2. CAPACITANCE CHANGE OF CAPACITORS - Class 1 capacitors Capacitance might change a little depending on a surrounding temperature or an applied voltage. Please contact us if you use for the strict time constant circuit. - Class 2 and 3 capacitors Class 2 and 3 capacitors like temperature characteristic B, E and F have an aging characteristic, whereby the capacitor continually decreases its capacitance slightly if the capacitor leaves for a long time. Moreover, capacitance might change greatly depending on a surrounding temperature or an applied voltage. So, it is not likely to be able to use for the time constant circuit. Please contact us if you need a detail information. NOTE 1.Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2.You are requested not to use our product deviating from this specification.
- Application This specification is applied to ceramic capacitor DEB series used for in electric equipment. DEB series is a high voltage disc ceramic capacitor of Class 2 and DC1 kV ratings. Do not use these products in any automotive power train or safety equipment including battery chargers for electric vehicles and plug-in hybrids. 2. Rating 2-1. Operating temperature range -25 +85C 2-2. Part number configuration ex.) DEB B3 3D 332 K A3 B . Series Temperature Rated Capacitance Capacitance Lead Packing Individual characteristic voltage tolerance code style code specification Temperature characteristic Code Temperature characteristic B3 B E3 E F3 F Please confirm detailed specification on Specification and test methods . Rated voltage Code Rated voltage 3D DC2kV 3F DC3.15kV Capacitance The first two digits denote significant figures ; the last digit denotes the multiplier of 10 in pF. ex.) In case of 332. 33102 = 3300pF Capacitance tolerance Please refer to Part number list . Lead code Code Lead style A Vertical crimp long type C Straight long type B Vertical crimp short type D Straight short type N Vertical crimp taping type P Straight taping type Please refer to Part number list . Solder coated copper wire is applied for termination.
Packing style code Code Packing type B Bulk type A Ammo pack taping type Individual specification In case part number cannot be identified without ‘individual specification’ , it is added at the end of part number. 3. Marking Temperature characteristic : Letter code Identified by code for char. B or char. E. (Omitted for maximum body diameter 9mm and under ) Nominal capacitance : 3 digit system Capacitance tolerance : Code(Omitted for maximum body diameter 6mm and under) Rated voltage : Letter code( In case of DC3.15kV, marked with 3KV) Company name code : Abbreviation (Omitted for maximum body diameter 9mm and under) Manufacturing year : Letter code(The last digit of A.D. year.) (Omitted for maximum body diameter 5mm and under) Manufacturing month : Code(Omitted for maximum body diameter 5mm and under) Feb./Mar. 2 Aug./Sep. 8 Apr./May 4 Oct./Nov. O Jun./Jul. 6 Dec./Jan. D (Example) B 332K 2KV
- Part number list Unit : mm T.C. Cap. (pF) Cap. tol. Customer Part Number Murata Part Number DC Rated Volt. (V) Dimension (mm) Lead Code Pack qty. (pcs)D T F d B 100 ±10% DEBB33D101KC1B 2000 4.5 5.0 5.0 0.5 C1 500 B 150 ±10% DEBB33D151KC1B 2000 4.5 5.0 5.0 0.5 C1 500 B 220 ±10% DEBB33D221KC1B 2000 4.5 5.0 5.0 0.5 C1 500 B 330 ±10% DEBB33D331KC1B 2000 5.0 5.0 5.0 0.5 C1 500 B 470 ±10% DEBB33D471KA2B 2000 6.0 5.0 5.0 0.6 A2 500 B 680 ±10% DEBB33D681KA2B 2000 7.0 5.0 5.0 0.6 A2 500 B 1000 ±10% DEBB33D102KA2B 2000 8.0 5.0 5.0 0.6 A2 250 B 1500 ±10% DEBB33D152KA2B 2000 9.0 5.0 5.0 0.6 A2 250 B 2200 ±10% DEBB33D222KA2B 2000 10.0 5.0 5.0 0.6 A2 250 B 3300 ±10% DEBB33D332KA3B 2000 12.0 5.0 7.5 0.6 A3 200 B 4700 ±10% DEBB33D472KA3B 2000 15.0 5.0 7.5 0.6 A3 100 B 100 ±10% DEBB33F101KCDB 3150 5.0 6.0 7.5 0.5 CD 500 B 150 ±10% DEBB33F151KCDB 3150 5.0 6.0 7.5 0.5 CD 500 B 220 ±10% DEBB33F221KCDB 3150 5.0 6.0 7.5 0.5 CD 500 B 330 ±10% DEBB33F331KC3B 3150 6.0 6.0 7.5 0.6 C3 500 B 470 ±10% DEBB33F471KC3B 3150 7.0 6.0 7.5 0.6 C3 250 B 680 ±10% DEBB33F681KA3B 3150 8.0 6.0 7.5 0.6 A3 250 B 1000 ±10% DEBB33F102KA3B 3150 9.0 6.0 7.5 0.6 A3 250 B 1500 ±10% DEBB33F152KA3B 3150 11.0 6.0 7.5 0.6 A3 250 B 2200 ±10% DEBB33F222KA3B 3150 13.0 6.0 7.5 0.6 A3 200 B 3300 ±10% DEBB33F332KA3B 3150 15.0 6.0 7.5 0.6 A3 100 E 1000 +80/-20% DEBE33D102ZA2B 2000 6.0 5.0 5.0 0.6 A2 500 E 2200 +80/-20% DEBE33D222ZA2B 2000 8.0 5.0 5.0 0.6 A2 250 E 4700 +80/-20% DEBE33D472ZA2B 2000 11.0 5.0 5.0 0.6 A2 250 E 10000 +80/-20% DEBE33D103ZA3B 2000 16.0 5.0 7.5 0.6 A3 100 E 1000 +80/-20% DEBE33F102ZC3B 3150 7.0 6.0 7.5 0.6 C3 250 E 2200 +80/-20% DEBE33F222ZA3B 3150 10.0 6.0 7.5 0.6 A3 250
Unit : mm T.C. Cap. (pF) Cap. tol. Customer Part Number Murata Part Number DC Rated Volt. (V) Dimension (mm) Lead Code Pack qty. (pcs)D T F d E 4700 +80/-20% DEBE33F472ZA3B 3150 13.0 6.0 7.5 0.6 A3 200 F 1000 +80/-20% DEBF33D102ZC1B 2000 5.0 5.0 5.0 0.5 C1 500 F 2200 +80/-20% DEBF33D222ZA2B 2000 7.0 5.0 5.0 0.6 A2 500 F 4700 +80/-20% DEBF33D472ZA2B 2000 9.0 5.0 5.0 0.6 A2 250 F 10000 +80/-20% DEBF33D103ZA3B 2000 12.0 5.0 7.5 0.6 A3 200
Unit : mm T.C. Cap. (pF) Cap. tol. Customer Part Number Murata Part Number DC Rated Volt. (V) Dimension (mm) Lead Code Pack qty. (pcs)D T F d B 100 ±10% DEBB33D101KD1B 2000 4.5 5.0 5.0 0.5 D1 500 B 150 ±10% DEBB33D151KD1B 2000 4.5 5.0 5.0 0.5 D1 500 B 220 ±10% DEBB33D221KD1B 2000 4.5 5.0 5.0 0.5 D1 500 B 330 ±10% DEBB33D331KD1B 2000 5.0 5.0 5.0 0.5 D1 500 B 470 ±10% DEBB33D471KB2B 2000 6.0 5.0 5.0 0.6 B2 500 B 680 ±10% DEBB33D681KB2B 2000 7.0 5.0 5.0 0.6 B2 500 B 1000 ±10% DEBB33D102KB2B 2000 8.0 5.0 5.0 0.6 B2 500 B 1500 ±10% DEBB33D152KB2B 2000 9.0 5.0 5.0 0.6 B2 500 B 2200 ±10% DEBB33D222KB2B 2000 10.0 5.0 5.0 0.6 B2 500 B 3300 ±10% DEBB33D332KB3B 2000 12.0 5.0 7.5 0.6 B3 250 B 4700 ±10% DEBB33D472KB3B 2000 15.0 5.0 7.5 0.6 B3 200 B 100 ±10% DEBB33F101KDDB 3150 5.0 6.0 7.5 0.5 DD 500 B 150 ±10% DEBB33F151KDDB 3150 5.0 6.0 7.5 0.5 DD 500 B 220 ±10% DEBB33F221KDDB 3150 5.0 6.0 7.5 0.5 DD 500 B 330 ±10% DEBB33F331KD3B 3150 6.0 6.0 7.5 0.6 D3 500 B 470 ±10% DEBB33F471KD3B 3150 7.0 6.0 7.5 0.6 D3 500 B 680 ±10% DEBB33F681KB3B 3150 8.0 6.0 7.5 0.6 B3 500 B 1000 ±10% DEBB33F102KB3B 3150 9.0 6.0 7.5 0.6 B3 500 B 1500 ±10% DEBB33F152KB3B 3150 11.0 6.0 7.5 0.6 B3 500 B 2200 ±10% DEBB33F222KB3B 3150 13.0 6.0 7.5 0.6 B3 250 B 3300 ±10% DEBB33F332KB3B 3150 15.0 6.0 7.5 0.6 B3 200 E 1000 +80/-20% DEBE33D102ZB2B 2000 6.0 5.0 5.0 0.6 B2 500 E 2200 +80/-20% DEBE33D222ZB2B 2000 8.0 5.0 5.0 0.6 B2 500 E 4700 +80/-20% DEBE33D472ZB2B 2000 11.0 5.0 5.0 0.6 B2 500 E 10000 +80/-20% DEBE33D103ZB3B 2000 16.0 5.0 7.5 0.6 B3 200 E 1000 +80/-20% DEBE33F102ZD3B 3150 7.0 6.0 7.5 0.6 D3 500 E 2200 +80/-20% DEBE33F222ZB3B 3150 10.0 6.0 7.5 0.6 B3 500
Unit : mm T.C. Cap. (pF) Cap. tol. Customer Part Number Murata Part Number DC Rated Volt. (V) Dimension (mm) Lead Code Pack qty. (pcs)D T F d E 4700 +80/-20% DEBE33F472ZB3B 3150 13.0 6.0 7.5 0.6 B3 250 F 1000 +80/-20% DEBF33D102ZD1B 2000 5.0 5.0 5.0 0.5 D1 500 F 2200 +80/-20% DEBF33D222ZB2B 2000 7.0 5.0 5.0 0.6 B2 500 F 4700 +80/-20% DEBF33D472ZB2B 2000 9.0 5.0 5.0 0.6 B2 500 F 10000 +80/-20% DEBF33D103ZB3B 2000 12.0 5.0 7.5 0.6 B3 250
Unit : mm T.C. Cap. (pF) Cap. tol. Customer Part Number Murata Part Number DC Rated volt. (V) Dimension (mm) Lead code Pack qty. (pcs)D T F d P
Unit : mm T.C. Cap. (pF) Cap. tol. Customer Part Number Murata Part Number DC Rated volt. (V) Dimension (mm) Lead code Pack qty. (pcs)D T F d P
- Specification and test methods No. Item Specification Test method
1 Appearance and dimensions No marked defect on appearance
form and dimensions. Please refer to [Part number list]. The capacitor should be inspected by naked eyes for visible evidence of defect. Dimensions should be measured with slide calipers. 2 Marking To be easily legible. The capa citor should be inspected by naked eyes.
3 Dielectric
No failure. The capacitor should not be damaged when DC voltage of 200% of the rated voltage are applied between the lead wires for 1 to 5 s. (Charge/Discharge current50mA.) Body insulation No failure. The capacitor is placed in the container with metal balls of diameter 1mm so that each lead wire, shortcircuited, is kept about 2mm off the balls as shown in the figure, and DC voltage of 1.3kV is applied for 1 to 5 s between capacitor lead wires and small metals. (Charge/Discharge current50mA.)
4 Insulation
Resistance (I.R.) Between lead wires 10000M min. The insulation resistance should be measured with DC50050V within 605 s of charging. 5 Capacitance Within specified tolerance. The capacitance should be measured at 20C with Char. F : 5.0% max. The dissipation factor should be measured at 20C 7 Temperature characteristic Char. B : Within 10% Char. E : Within +20/-55% Char. F : Within +30/-80% The capacitance measurement should be made at each step specified in Table. Pre-treatment : Capacitor should be stored at 852C for 1 h, then placed at *room condition for 242 h before initial measurements.
8 Strength of lead
Pull Lead wire should not cut off. Capacitor should not be broken. As shown in the figure at right, fix the body of the capacitor and apply a tensile weight gradually to each lead wire in the radial direction of the capacitor up to 10N ( 5N for lead diameter 0.5mm ), and keep it for 101 s. Bending Each lead wire should be subjected to 5N ( 2.5N for lead diameter 0.5mm ) of weight and bent 90 at the point of egress, in one direction, then returned to its original position, and bent 90 in the opposite direction at the rate of one bend in 2 to 3 s.
9 Vibration
Appearance No marked defect. The capacito r should be firmly soldered to the supporting lead wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in total amplitude, with about a 1min rate of vibration change from 10Hz to 55Hz and back to 10Hz. Apply for a total of 6 h; 2 h each in 3 mutually perpendicular directions. Capacitance Within specified tolerance. Char. F : 5.0% max.
10 Solderability of leads Lead wire should be soldered
with uniformly coated on the axial direction over 3/4 of the circumferential direction. The lead wire of a capacitor should be dipped into a ethanol solution of 25wt% rosin and then into molten solder for 20.5 s. In both cases the depth of dipping is up to about 1.5 to 2mm from the root of lead wires. Temp. of solder : 245±5°C Lead Free Solder (Sn-3Ag-0.5Cu) 235±5°C H63 Eutectic Solder * "room condition" Temperature: 15 to 35C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa Step 1 2 3 4 5 Temp.(C) 20 2- 2 5 32 0 2 85 2 20 2
No. Item Specification Test method
11 Soldering effect
(Non-preheat) Appearance No marked defect. The lead wire should be immersed into the melted solder of 35010C ( Body of 5 and under: 2705C ) up to about 1.5 to 2.0mm from the main body for 3.50.5 s. ( Body of 5 and under: 50.5 s. ) Pre-treatment : Capacitor should be stored at 85 2C for 1 h, then placed at * room condition for 24 2 h before initial measurements. Post-treatment : Capacitor should be stored for 4 to 24 h at * room condition. Capacitance change Char. B : Within 5% Char. E : Within 15% Char. F : Within 20% Dielectric strength (Between lead wires) Per item 3. 12 Soldering effect (On-preheat) Appearance No marked defect. First t he capacitor should be stored at Then, as in figure, the lead wires should be immersed solder of 260+0/-5°C up to 1.5 to 2.0mm from the root of terminal for 7.5+0/-1 s. Pre-treatment : Capacitor should be stored at 85 2C for 1 h, then placed at * room condition for 24 2 h before initial measurements. Post-treatment : Capacitor should be stored for 4 to 24 h at * room condition. Capacitance change Char. B : Within 5% Char. E : Within 15% Char. F : Within 20% Dielectric strength (Between lead wires) Per item 3.
13 Humidity
(Under steady state) Appearance No marked defect. Set the capacitor for 500 +24/-0 h at 402C in 90 to 95% relative humidity. Pre-treatment : Capacitor should be stored at 85 2C for 1 h, then placed at * room condition for 24 2 h before initial measurements. Post-treatment : Capacitor should be stored for 1 to 2 h at * room condition. Capacitance change Char. B : Within 10% Char. E : Within 20% Char. F : Within 30% Char. F : 7.5% max. I.R. 1000M min. 14 Humidity loading Appear ance No marked defect. Apply the rated voltage for 500 +24/-0 h at 402C in 90 to 95% relative humidity. (Charge/Discharge current50mA.) Pre-treatment : Capacitor should be stored at 85 2C for 1 h, then placed at * room condition for 24 2 h before initial measurements. Post-treatment : Capacitor should be stored at 852C for 1 h, then placed at * room condition for 242 h. Capacitance change Char. B : Within 10% Char. E : Within 20% Char. F : Within 30% Char. F : 7.5% max. I.R. 500M min. 15 Life Appearance No marked defect. Apply a DC voltage of 150% of the rated voltage for 1000 +48/-0 h at 852C, and relative humidity of 50% max.. (Charge/Discharge current50mA.) Pre-treatment : Capacitor should be stored at 85 2C for 1 h, then placed at * room condition for 24 2 h before initial measurements. Post-treatment : Capacitor should be stored at 852C for 1 h, then placed at * room condition for 242 h. Capacitance change Char. B : Within 10% Char. E : Within 20% Char. F : Within 30% Char. F : 7.5% max. I.R. 2000M min. * "room condition" Temperature: 15 to 35C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
No. Item Specification Test method
16 Temperature and
Appearance No marked defect. The capa citor should be subjected to 5 temperature cycles, then consecutively to 2 immersion cycles. <Temperature cycle> Cycle time : 5 cycle <Immersion cycle> Cycle time : 2 cycle Pre-treatment : Capacitor should be stored at 85 2C for 1 h, then placed at * room condition for 24 2 h before initial measurements. Post-treatment : Capacitor should be stored for 4 to 24 h at * room condition. Capacitance change Char. B : Within 10% Char. E : Within 20% Char. F : Within 30% Char. F : 7.5% max. I.R. 2000M min. Dielectric strength (Between lead wires) Per item 3. * "room condition" Temperature: 15 to 35C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa Step Temperature(C) Time 1 -253 30 min 2 Room Temp. 3 min 3 +853 30 min 4 Room Temp. 3 min Step Temperature(C) Time Immersion water 1 +65+5/-0 15 min Clean water 2 03 15 min Salt water
6.Packing specification Bulk type (Packing style code : B) The number of packing = Packing quantity n The size of packing case and packing way 1 : Please refer to [Part number list]. 2 : Standard n = 20 (bag) Ammo pack taping type (Packing style code : A) The tape with capacitors is packed zigzag into a case. When body of the capacitor is piled on other body under it. There should be 3 pitches and over without capacitors in leader and trailer. Unit : mm 340 max. 125 max. 270 max. Partition Polyethylene bag 240 max. 340 max. Position of label 60 max. The size of packing case and packing way Capacitor Base tape Hold down tape Hold down tape upper Unit : mm Note) The outer package and the number of outer packing be changed by the order getting amount.
- Taping specification 7-1. Dimension of capacitors on tape Vertical crimp taping type < Lead code : N2 > Pitch of component 12.7mm / Lead spacing 5.0mm Unit : mm Item Code Dimensions Remarks Pitch of component P 12.7 1.0 Pitch of sprocket hole P0 12.7 0.3 Lead spacing F 5.0 Length from hole center to component center P2 6.35 1.3 Deviation of progress direction Length from hole center to lead P1 3.85 0.7 Body diameter D Please refer to [Part number list ]. Deviation along tape, left or right S 0 1.0 They include deviation by lead bend . Carrier tape width W 18.0 0.5 Position of sprocket hole W1 9.0 0.5 Deviation of tape width direction Lead distance between reference and bottom planes H0 18.0 Protrusion length 0.51.0 Diameter of sprocket hole D0 4.0 0.1 Lead diameter d 0.60 0.05 Total tape thickness t1 0.6 0.3 They include hold down tape thickness. Total thickness, tape and lead wire t2 1.5 max. Deviation across tape, front h1 1.0 max. Deviation across tape, rear h2 Portion to cut in case of defect L 11.0 Hold down tape width W0 11.5 min. Hold down tape position W2 1.5 1.5 Coating extension on lead e Up to the end of crimp Body thickness T Please refer to [Part number list ]. 2.0 1.0 0.8 0.2
Vertical crimp taping type < Lead code : N3 > Pitch of component 15.0mm / Lead spacing 7.5mm Unit : mm Item Code Dimensions Remarks Pitch of component P 15.0 2.0 Pitch of sprocket hole P0 15.0 0.3 Lead spacing F 7.5 1.0 Length from hole center to component center P2 7.5 1.5 Deviation of progress direction Length from hole center to lead P1 3.75 1.0 Body diameter D Please refer to [ Part number list ]. Deviation along tape, left or right S 0 2.0 They include deviation by lead bend . Carrier tape width W 18.0 0.5 Position of sprocket hole W1 9.0 0.5 Deviation of tape width direction Lead distance between reference and bottom planes H0 18.0 Protrusion length 0.51.0 Diameter of sprocket hole D0 4.0 0.1 Lead diameter d 0.60 0.05 Total tape thickness t1 0.6 0.3 They include hold down tape thickness. Total thickness, tape and lead wire t2 1.5 max. Deviation across tape, front h1 2.0 max. Deviation across tape, rear h2 Portion to cut in case of defect L 11.0 Hold down tape width W0 11.5 min. Hold down tape position W2 1.5 1.5 Coating extension on lead e Up to the end of crimp Body thickness T Please refer to [ Part number list ]. 2.0 1.0
Vertical crimp taping type < Lead code : N7 > Pitch of component 30.0mm /Lead spacing 7.5mm Unit : mm Item Code Dimensions Remarks Pitch of component P 30.0 2.0 Pitch of sprocket hole P0 15.0 0.3 Lead spacing F 7.5 1.0 Length from hole center to component center P2 7.5 1.5 Deviation of progress direction Length from hole center to lead P1 3.75 1.0 Body diameter D Please refer to [ Part number list ]. Deviation along tape, left or right S 0 2.0 They include deviation by lead bend. Carrier tape width W 18.0 0.5 Position of sprocket hole W1 9.0 0.5 Deviation of tape width direction Lead distance between reference and bottom planes H0 18.0 Protrusion length 0.51.0 Diameter of sprocket hole D0 4.0 0.1 Lead diameter d 0.60 0.05 Total tape thickness t1 0.6 0.3 They include hold down tape thickness. Total thickness, tape and lead wire t2 1.5 max. Deviation across tape, front h1 2.0 max. Deviation across tape, rear h2 Portion to cut in case of defect L 11.0 Hold down tape width W0 11.5 min. Hold down tape position W2 1.5 1.5 Coating extension on lead e Up to the end of crimp Body thickness T Please refer to [ Part number list ]. 2.0 1.0
Straight taping type < Lead code: P2 > Pitch of component 12.7mm / Lead spacing 5.0mm Unit : mm Item Code Dimensions Remarks Pitch of component P 12.7 1.0 Pitch of sprocket hole P0 12.7 0.3 Lead spacing F 5.0 Length from hole center to component center P2 6.35 1.3 Deviation of progress direction Length from hole center to lead P1 3.85 0.7 Body diameter D Please refer to [ Part number list ]. Deviation along tape, left or right S 0 1.0 They include deviation by lead bend . Carrier tape width W 18.0 0.5 Position of sprocket hole W1 9.0 0.5 Deviation of tape width direction Lead distance between reference and bottom planes H 20.0 Protrusion length 0.51.0 Diameter of sprocket hole D0 4.0 0.1 Lead diameter d 0.60 0.05 Total tape thickness t1 0.6 0.3 They include hold down tape thickness. Total thickness, tape and lead wire t2 1.5 max. Deviation across tape, front h1 1.0 max. Deviation across tape, rear h2 Portion to cut in case of defect L 11.0 Hold down tape width W0 11.5 min. Hold down tape position W2 1.5 1.5 Coating extension on lead e 3.0 max. Body thickness T Please refer to [ Part number list ]. 1.5 1.0 1.0 0.8 0.2
Straight taping type < Lead code : P3 > Pitch of component 15.0mm / Lead spacing 7.5mm Unit : mm Item Code Dimensions Remarks Pitch of component P 15.0 2.0 Pitch of sprocket hole P0 15.0 0.3 Lead spacing F 7.5 1.0 Length from hole center to component center P2 7.5 1.5 Deviation of progress direction Length from hole center to lead P1 3.75 1.0 Body diameter D Please refer to [ Part number list ]. Deviation along tape, left or right S 0 2.0 They include deviation by lead bend . Carrier tape width W 18.0 0.5 Position of sprocket hole W1 9.0 0.5 Deviation of tape width direction Lead distance between reference and bottom planes H 20.0 Protrusion length 0.51.0 Diameter of sprocket hole D0 4.0 0.1 Lead diameter d 0.60 0.05 Total tape thickness t1 0.6 0.3 They include hold down tape thickness. Total thickness, tape and lead wire t2 1.5 max. Deviation across tape, front h1 2.0 max. Deviation across tape, rear h2 Portion to cut in case of defect L 11.0 Hold down tape width W0 11.5 min. Hold down tape position W2 1.5 1.5 Coating extension on lead e 3.0 max. Body thickness T Please refer to [ Part number list ]. 1.5 1.0 1.0
7-2. Splicing way of tape 1) Adhesive force of tape is over 3N at test condition as below. 2) Splicing of tape a) When base tape is spliced Base tape should be spliced by cellophane tape. (Total tape thickness should be less than 1.05mm.) b) When hold down tape is spliced Hold down tape should be spliced with overlapping. (Total tape thickness should be less than 1.05mm.) ape are spliced Base tape and adhesive tape should be spliced with splicing tape. c) When both tape are spliced Base tape and hold down tape should be spliced with splicing tape. 3 ) Missing components There should be no consecutive missing of more than three components. The number of missing components should be not more than 0.5% of total components that should be present in a Ammo pack. Hold down tape Base tape W Unit : mm Progress direction in production line Hold down tape Base tape Cellophane tapeAbout 30 to 50 Progress direction in production line Hold down tape Base tape 20 to 60 Unit : mm No lifting for the direction of progressing
This products of the following crresponds to EU RoHS. RoHS maximum concentration values tolerated by weight in homogeneous materials ・1000 ppm maximum Lead ・1000 ppm maximum Mercury ・100 ppm maximum Cadmium ・1000 ppm maximum Hexavalent chromium ・1000 ppm maximum Polybrominated biphenyls (PBB) ・1000 ppm maximum Polybrominated diphenyl ethers (PBDE)