DDU66F-16D1

DDU66F DATADELAY | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

Doc #97020 DATA DELAY DEVICES, INC. 2/5/97 3 Mt. Prospect Ave. Clifton, NJ 07013 5-TAP, TTL-INTERFACED FIXED DELAY LINE (SERIES DDU66F)

FEATURES

Five equally spaced outputs Fits standard 14-pin DIP socket Low profile Auto-insertable Input & outputs fully TTL interfaced & buffered

10 T2L fan-out capability

The DDU66F-series device is a 5-tap digitally buffered delay line. The signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an amount given by the device dash number. For dash numbers less than 25, the total delay of the line is measured from T1 to T5, with the nominal value given by the dash number. The nominal tap-to-tap delay increment is given by 1/4 of this number. The inherent delay from IN to T1 is nominally 3.5ns. For dash numbers greater than or equal to 25, the total delay of the line is measured from IN to T5, with the nominal value given by the dash number. The nominal tap-to-tap delay increment is given by 1/5 of this number. SERIES SPECIFICATIONS Minimum input pulse width: 40% of total delay Output rise time: 2ns typical Supply voltage: 5VDC ± 5% Supply current: ICCL = 32ma typical ICCH = 7ma typical Operating temperature: 0° to 70° C Temp. coefficient of total delay: 100 PPM/°C 25% 25% 25% 25% VCC GND IN Functional diagram for dash numbers < 25 3.5ns 20% 20% 20% 20% 20% VCC GND IN Functional diagram for dash numbers >= 25 1997 Data Delay Devices data delay devices, inc. IN GND VCC IN N/C N/C N/C GND VCC N/C N/C N/C DDU66F-xxD1 Com. SMD DDU66F-xxD4 Com. SMD DDU66F-xxMD1 Mil. SMD DDU66F-xxMD4 Mil. SMD DDU66F-xx DIP DDU66F-xxA2 Gull-Wing DDU66F-xxB2 J-Lead DDU66F-xxME7 Military DIP PIN DESCRIPTIONS IN Signal Input T1-T5 Tap Outputs VCC +5 Volts GND Ground DASH NUMBER SPECIFICATIONS Part Number Total Delay (ns) Delay Per Tap (ns) DDU66F-4 4 ± 1.0 * 1.0 ± 0.5 DDU66F-6 6 ± 1.0 * 1.5 ± 0.5 DDU66F-8 8 ± 2.0 * 2.0 ± 1.0 DDU66F-10 10 ± 2.0 * 2.5 ± 1.0 DDU66F-12 12 ± 2.0 * 3.0 ± 1.0 DDU66F-16 16 ± 2.0 * 4.0 ± 1.5 DDU66F-20 20 ± 3.0 * 5.0 ± 1.5 DDU66F-25 25 ± 3.0 5.0 ± 2.0 DDU66F-30 30 ± 3.0 6.0 ± 2.0 DDU66F-35 35 ± 3.0 7.0 ± 2.0 DDU66F-40 40 ± 3.0 8.0 ± 2.0 DDU66F-45 45 ± 3.0 9.0 ± 3.0 DDU66F-50 50 ± 3.0 10.0 ± 3.0 DDU66F-60 60 ± 3.0 12.0 ± 3.0 DDU66F-75 75 ± 4.0 15.0 ± 3.0 DDU66F-100 100 ± 5.0 20.0 ± 3.0 DDU66F-125 125 ± 6.5 25.0 ± 3.0 DDU66F-150 150 ± 7.5 30.0 ± 3.0 DDU66F-175 175 ± 8.0 35.0 ± 4.0 DDU66F-200 200 ± 10.0 40.0 ± 4.0 DDU66F-250 250 ± 12.5 50.0 ± 5.0 * Total delay is referenced to first tap output Input to first tap = 3.5ns ±± 1ns NOTE: Any dash number between 4 and 250 not shown is also available.

Doc #97020 DATA DELAY DEVICES, INC. 2/5/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com APPLICATION NOTES HIGH FREQUENCY RESPONSE The DDU66F tolerances are guaranteed for input pulse widths and periods greater than those specified in the test conditions. Although the device will function properly for pulse widths as small as 40% of the total delay and periods as small as 80% of the total delay (for a symmetric input), the delays may deviate from their values at low frequency. However, for a given input condition, the deviation will be repeatable from pulse to pulse. Contact technical support at Data Delay Devices if your application requires device testing at a specific input condition. POWER SUPPLY BYPASSING The DDU66F relies on a stable power supply to produce repeatable delays within the stated tolerances. A 0.1uf capacitor from VCC to GND, located as close as possible to the VCC pin, is recommended. A wide VCC trace and a clean ground plane should be used. DEVICE SPECIFICATIONS TABLE 1: ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL MIN MAX UNITS NOTES DC Supply Voltage VCC -0.3 7.0 V Input Pin Voltage VIN -0.3 VCC+0.3 V Storage Temperature TSTRG -55 150 C Lead Temperature TLEAD 300 C 10 sec TABLE 2: DC ELECTRICAL CHARACTERISTICS (0C to 70C, 4.75V to 5.25V) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES High Level Output Voltage VOH 2.5 3.4 V VCC = MIN, IOH = MAX VIH = MIN, VIL = MAX Low Level Output Voltage VOL 0.35 0.5 V VCC = MIN, IOL = MAX VIH = MIN, VIL = MAX High Level Output Current IOH -1.0 mA Low Level Output Current IOL 20.0 mA High Level Input Voltage VIH 2.0 V Low Level Input Voltage VIL 0.8 V Input Clamp Voltage VIK -1.2 V VCC = MIN, II = IIK Input Current at Maximum Input Voltage IIHH 0.1 mA VCC = MAX, VI = 7.0V High Level Input Current IIH µA VCC = MAX, VI = 2.7V Low Level Input Current IIL -0.6 mA VCC = MAX, VI = 0.5V Short-circuit Output Current IOS -60 -150 mA VCC = MAX Output High Fan-out Unit Output Low Fan-out 12.5 Load

Doc #97020 DATA DELAY DEVICES, INC. 2/5/97 3 Mt. Prospect Ave. Clifton, NJ 07013 PACKAGE DIMENSIONS DDU66F-xx (Commercial) .780 MAX. .290 MAX. .015 TYP. .070 MAX. .018 TYP. .600±.010 .280 MAX. .350 MAX. .010±.002 Lead Material: Nickel-Iron alloy 42 TIN PLATE DDU66F-xxME7 (Military) .130 ±.030 .820 MAX. .320 MAX. .018 TYP. .410 TYP. .300 TYP. .020 TYP. .600 TYP. .020 TYP. .100 TYP. .790 MAX. .430 TYP. .020 TYP. .040 TYP. .100 .090 .600 .300 MAX. .270 TYP. .010 TYP. .050 TYP. DDU66F-xxA2 (Commercial Gull-Wing) .790 MAX. .320 TYP. .020 TYP. .040 TYP. .100 .110 .600 .350 MAX. .270 TYP. .050 TYP. .110 TYP. DDU66F-xxB2 (Commercial J-Lead) .008 .510 MAX. .510 MAX. .045 .300 TYP. .017 .050 .100 .100 .025 .300 .300 .360 TYP. .065 TYP. .065 TYP. .200 MAX. (Com) .225 MAX. (Mil) DDU66F-xxD1 (Commercial SMD) DDU66F-xxMD1 (Military SMD) .200 MAX. (Com) .225 MAX. (Mil) .080 .080 .510 MAX. .510 MAX. .017 .050 .300 TYP. .100 .100 .650 .008 .005 .065 TYP. .360 TYP. .065 TYP. DDU66F-xxD4 (Commercial SMD) DDU66F-xxMD4 (Military SMD)

Doc #97020 DATA DELAY DEVICES, INC. 2/5/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com DELAY LINE AUTOMATED TESTING TEST CONDITIONS INPUT: OUTPUT: Ambient Temperature: 25oC ± 3oC Load:

1 FAST-TTL Gate

Supply Voltage (Vcc): 5.0V ± 0.1V Cload: 5pf ± 10% Input Pulse: High = 3.0V ± 0.1V Threshold: 1.5V (Rising & Falling) Low = 0.0V ± 0.1V Source Impedance: 50Ω Max. Rise/Fall Time: 3.0 ns Max. (measured between 0.6V and 2.4V ) Pulse Width: PWIN = 1.5 x Total Delay Period: PERIN = 10 x Total Delay NOTE: The above conditions are for test only and do not in any way restrict the operation of the device. OUT TRIG IN REF TRIG Test Setup DEVICE UNDER TEST (DUT) TIME INTERVAL COUNTER PULSE GENERATOR COMPUTER SYSTEM PRINTER IN Timing Diagram For Testing TRISE TFALL PERIN PWIN TRISE TFALL 0.6V 0.6V 1.5V 1.5V 2.4V 2.4V 1.5V 1.5V VIH VIL VOH VOL INPUT SIGNAL OUTPUT SIGNAL