DCS8-140E POWERBOX | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
- High power density Remote voltage sense & remote programming Wide range of output voltages High programming resolution with ethernet interface Remote control Specifications INPUT Input voltage 1KW: 200-250VAC, single phase; 100-132VAC single phase, internal jumper selectable (see M1 option) 1.2KW: 200-250VAC, single phase; 100- 132VAC single phase, internal jumper selectable (see M1 option) 3KW: 190-250VAC, three phase; 200-250VAC, single phase (Note: Max.power output of 3KW supplies must be limited to 2.5KW for single phase input) Frequency 47-63Hz for both single and three phase input Current 1KW: 15A typ at 115VAC, 8A typ at 230VAC, 1.2KW: 18A typ at 115VAC, 9A typ at 230VAC, 3KW: 20A typ at 230VAC single phase, 14A typ at 230VAC three phase Soft start Line current is lower than full load peak value during turn-on or power application after restart ENVIRONMENTAL Operating temperature 0°C to 50° (No De-rating) Storage temperature -40°C to 85°C Humidity range 0-80% RH, non condensing Cooling Internal fan with over-temperature protection OUTPUT Voltage adjustment Zero to rated output Current adjustment Zero to rated output Ripple & Noise See table Regulation (Line or Load) Voltage: 0.1% Current: 0.1% Transient response Typically recovers in < 1ms to 1% of steady-state output voltage (within 1% of Vmax) for 70-100% or 100-70% load change. 500/H9262s typical Stability +/-0.05% of maximum voltage or current over 8 hours after 30 minute warm-up time at fixed line, load and temperature Temperature Coefficient 0.02%/°C of maximum output voltage 0.03%/°C of maximum output current INPUT VOLTAGE OPTIONS M1 Factory configured for 115VAC input (1 and 1.2kW only) REMOTE INTERFACE OPTIONS M9C Internal IEEE-488/RS 232 interface M13 Locking shafts (front panel potentiometers) M32 Master/slave cable configured for two or more units M33 Replace input connector with terminal block (3kW only) M51A Isolated analog programming control of V/I/OVP and isolated V/I monitor outputs up to 500V relative to the supply’s return line M85 Multichannel slave interface M102 Front panel binding posts for 1kw or 1.2 kW, Models /H11088/H1108830A, /H11088/H11088100V. Not compatible with M9C, M85, M130, M131, M133, M135, M136 M130 LXI compliant 10/100 Base T Ethernet remote control master interface; includes web server for direct control of power supply via web browser (MS Internet Explorer 6.0 or later) M131 16-bit slave interface option for use with a M130 master (3 ft. control cable included) M133 Output disconnect and polarity reversal controlled via SCPI commands. Limited to 1k or 1.2 kW, /H11088/H11088 300V,/H11088/H11088 60A M135 M130 & M133 combination M136 M131 & M133 combination 105-330-26 Rack slide kit (3kW) OPERATING Efficiency See table Remote sense The maximum allowed sense line drop is 4V per line (2V on the DCS 8 and 10V 1KW and 1.2KW models and 1V/ line for all 3KW models) Remote programming External jumper via rear panel connectors J3. Overvoltage protection Crowbar type adjustable from 5-110% Protection rated output using front panel control (local or remote program selectable via J3 jumper) Remote analog programming Linearity: +/-1% Accuracy: +/-5% Software LabVIEW® driver for M9C/M85 (Contact Powerbox) Regulatory compliance CE Mark on all models, FCC Part 15 Class A UL1012 and CSA 22.2 #220 (1 and 1.2 KW only) Options and Accessories
486 LABORATORY
1000-3000 WATTS PROGRAMMABLE DC SUPPLY MODEL CONSTANT CURRENT MODE* TEMP. COEFF. VOLTAGE %/°C (TYP) VOLTAGE DRIFT % % IO MAX (TYP) PROGRAMMING CONSTANTS CURRENT MODE INPUT CURRENT, A NORMAL EFFICIENCY % (TYP) CASE COMBINED REGULATION LINE AND LOAD % RIPPLE (RMS) OHMS/A V/A 230V SINGLE PHASE 208V THREE PHASE DCS 8-140E 0.2 180 0.03 0.05 35.7 0-10V= 0-100% Io or 0-5V= 0-100% Io
9 N/A 82 I
DCS 10-120E 0.2 153 0.03 0.05 41.7 9 N/A 82 I DCS 20-60E 0.2 30 0.03 0.05 83.3 9 N/A 82 I DCS 33-36E 0.2 11 0.03 0.05 138.9 9 N/A 84 I DCS 40-30E 0.2 9 0.03 0.05 166.7 9 N/A 84 I DCS 60-20E 0.2 6.6 0.03 0.05 250 9 N/A 85 I DCS 80-15E 0.2 6 0.03 0.05 333.3 9 N/A 85 I DCS 150-8E 0.2 2.3 0.03 0.05 625 9 N/A 85 I DCS 300-4E 0.2 1.2 0.03 0.05 1250 9 N/A 85 I * Typical resolution is 0.02% RMS ripple from 20Hz to 300kHz *Consult factory Dimension: 1RU or 44mm (H) x 482mm (W) x 444mm (D) ; Weight: 8.6kg86 MODEL OUTPUT POWER COMBINED REGULATION LINE AND LOAD % CONSTANT VOLTAGE MODE* TEMP. COEFF. VOLTAGE %/°C (TYP) VOLTAGE DRIFT % VMAX (TYP) PROGRAMMING CONSTANTS VOLTAGE MODES VOLTAGE VDC CURRENT ADC @ 50°C RIPPLE (RMS)** (TYP.) NOISE (P-P) (TYP) TRANSIENT RESPONSE TIME (TYP) OHMS/V V/V DCS 8-350E 0-8 0-350 0.2 15mV 100mV 1000/H9262s 0.02 0.05 625 0-10V = 0-100% Vo or 0-5V = 0-100% Vo DCS 12-250E 0-12 0-250 0.2 10mV 100mV 1000/H9262s 0.02 0.05 416.7 DCS 20-150E 0-20 0-150 0.2 10mV 100mV 1000/H9262s 0.02 0.05 250 DCS 40-75E 0-40 0-75 0.2 20mV 100mV 1000/H9262s 0.02 0.05 125 DCS 55-55E 0-55 0-55 0.2 20mV 100mV 1000/H9262s 0.02 0.05 90.9 DCS 60-50E 0-60 0-50 0.2 20mV 100mV 1000/H9262s 0.02 0.05 83 DCS 80-37E 0-80 0-37 0.2 20mV 100mV 1000/H9262s 0.02 0.05 62.5 DCS 150-20E 0-150 0-20 0.2 30mV 200mV 1000/H9262s 0.02 0.05 33.3 MODEL CONSTANT CURRENT MODE* TEMP. COEFF. VOLTAGE %/°C (TYP) VOLTAGE DRIFT % % IO MAX (TYP) PROGRAMMING CONSTANTS CURRENT MODE INPUT CURRENT, A NORMAL EFFICIENCY % (TYP) CASE COMBINED REGULATION LINE AND LOAD % RIPPLE (RMS) OHMS/A V/A 230V SINGLE PHASE 208V THREE PHASE DCS 8-350E 0.2 870 0.03 0.05 14.7 0-10V= 0-100% I0 or 0-5V= 0-100% I0 24 13 82 II DCS 12-250E 0.2 400 0.03 0.05 20 26 14 82 II DCS 20-150E 0.2 100 0.03 0.05 33.3 26 14 82 II DCS 40-75E 0.2 75 0.03 0.05 66.7 26 14 86 II DCS 55-55E 0.2 40 0.03 0.05 90.9 26 14 82 II DCS 60-50E 0.2 33 0.03 0.05 100 26 14 86 II DCS 80-37E 0.2 20 0.03 0.05 135 26 14 86 II DCS 150-20E 0.2 10 0.03 0.05 250 26 14 86 II * Typical resolution is 0.02% RMS ripple from 20Hz to 300kHz *Consult factory Dimension: 2RU or 88mm (H) x 482mm (W) x 444mm (D) ; Weight: 15kg DSC 3kW Series
Your dependable power partner – www.powerbox.com.au 485 LABORATORY DCS Series 1000-3000 WATTS PROGRAMMABLE DC SUPPLY MODEL OUTPUT POWER COMBINED REGULATION LINE AND LOAD % CONSTANT VOLTAGE MODE* TEMP. COEFF. VOLTAGE %/°C (TYP) VOLTAGE DRIFT % VMAX (TYP) PROGRAMMING CONSTANTS VOLTAGE MODES VOLTAGE VDC CURRENT ADC @ 50°C RIPPLE (RMS)** (TYP.) NOISE (P-P) (TYP) TRANSIENT RESPONSE TIME (TYP) OHMS/V V/V DCS 8-125E 0-8 0-125 0.2 4mV 60mV 500/H9262s 0.02 0.05 625 0-10V = 0-100% Vo or 0-5V = 0-100% Vo DCS 10-100E 0-10 0-100 0.2 4mV 60mV 500/H9262s 0.02 0.05 500 DCS 20-50E 0-20 0-50 0.2 4mV 60mV 500/H9262s 0.02 0.05 250 DCS 33-33E 0-33 0-33 0.2 4mV 60mV 500/H9262s 0.02 0.05 151.5 DCS 40-25E 0-40 0-25 0.2 4mV 60mV 500/H9262s 0.02 0.05 125 DCS 50-20E 0-50 0-20 0.2 4mV 60mV 500/H9262s 0.02 0.05 100 DCS 60-18E 0-60 0-18 0.2 4mV 60mV 500/H9262s 0.02 0.05 83 DCS 80-13E 0-80 0-13 0.2 4mV 60mV 500/H9262s 0.02 0.05 62.5 DCS 100-10E 0-100 0-10 0.2 6mV 60mV 500/H9262s 0.02 0.05 50 DCS 150-7E 0-150 0-7 0.2 12mV 160mV 500/H9262s 0.02 0.05 33.3 MODEL CONSTANT CURRENT MODE* TEMP. COEFF. VOLTAGE %/°C (TYP) VOLTAGE DRIFT % % IO MAX (TYP) PROGRAMMING CONSTANTS CURRENT MODE INPUT CURRENT, A NORMAL EFFICIENCY % (TYP) CASE COMBINED REGULATION LINE AND LOAD % RIPPLE (RMS) OHMS/A V/A 230V SINGLE PHASE 208V THREE PHASE DCS 8-125E 0.2 160 0.03 0.05 40 0-10V= 0-100% Io or 0-5V= 0-100% Io
8 N/A 82 I
DCS 10-100E 0.2 128 0.03 0.05 50 8 N/A 82 I DCS 20-50E 0.2 25 0.03 0.05 100 8 N/A 82 I DCS 33-33E 0.2 10 0.03 0.05 151.5 8 N/A 84 I DCS 40-25E 0.2 7 0.03 0.05 200 8 N/A 84 I DCS 50-20E 0.2 7 0.03 0.05 250 8 N/A 84 I DCS 60-18E 0.2 6 0.03 0.05 277.8 8 N/A 86 I DCS 80-13E 0.2 4 0.03 0.05 384.6 8 N/A 86 I DCS 100-10E 0.2 3 0.03 0.05 500 8 N/A 86 I DCS 150-7E 0.2 2 0.03 0.05 714.3 8 N/A 86 I * Typical resolution is 0.02% RMS ripple from 20Hz to 300kHz *Consult factory Dimension: 1RU or 44mm (H) x 482mm (W) x 444mm (D) ; Weight: 8.6kg MODEL OUTPUT POWER COMBINED REGULATION LINE AND LOAD % CONSTANT VOLTAGE MODE* TEMP. COEFF. VOLTAGE %/°C (TYP) VOLTAGE DRIFT % VMAX (TYP) PROGRAMMING CONSTANTS VOLTAGE MODES VOLTAGE VDC CURRENT ADC @ 50°C RIPPLE (RMS)** (TYP.) NOISE (P-P) (TYP) TRANSIENT RESPONSE TIME (TYP) OHMS/V V/V DCS 8-140E 0-8 0-140 0.2 5mV 60mV 500/H9262s 0.02 0.05 625 0-10V = 0-100% Vo or 0-5V = 0-100% Vo DCS 10-120E 0-10 0-120 0.2 5mV 60mV 500/H9262s 0.02 0.05 500 DCS 20-60E 0-20 0-60 0.2 5mV 60mV 500/H9262s 0.02 0.05 250 DCS 33-36E 0-33 0-36 0.2 5mV 60mV 500/H9262s 0.02 0.05 151.5 DCS 40-30E 0-40 0-30 0.2 5mV 60mV 500/H9262s 0.02 0.05 125 DCS 50-24E 0-50 0-24 0.2 5mV 60mV 500/H9262s 0.02 0.05 100 DCS 60-20E 0-60 0-20 0.2 5mV 60mV 500/H9262s 0.02 0.05 83 DCS 80-15E 0-80 0-15 0.2 5mV 60mV 500/H9262s 0.02 0.05 62.5 DCS 100-12E 0-100 0-12 0.2 10mV 60mV 500/H9262s 0.02 0.05 50 DCS 150-8E 0-150 0-8 0.2 15mV 160mV 500/H9262s 0.02 0.05 33.3 DCS 300-4E 0-300 0-4 0.2 25mV 200mV 500/H9262s 0.02 0.05 16.67 DSC 1kW Series DSC 1.2kW Series
Your dependable power partner – www.powerbox.com.au 487 LABORATORY DCS Series 1000-3000 WATTS PROGRAMMABLE DC SUPPLY Technical Illustrations 1KW AND 1.2KW 3KW Options & Accesssories INPUT VOLTAGE OPTIONS M1 Factory configured for 115 VAC input (1 and 1.2 kW only) REMOTE INTERFACE OPTIONS M9C Internal IEEE-488/RS 232 interface (Supports only 12-bit slaves) M13 Locking shafts (front panel potentiometers) M32 Master/slave cable configured for two or more units M33 Replace input connector with terminal block(3 kW only) M51A Isolated analog programming control M102 Front Panel Binding Posts (1 kW and 1.2 kW only?30A) M85 12-bit slave interface M130 Ethernet/RS232 Interface (Supports both 12- & 16-bit slaves) M131 16-bit slave interface M133 Output disconnect and polarity reversal relays* M135 Output disconnect and polarity reversal relays M136 Output disconnect and polarity reversal relays* 105-330-26 Rack slide kit (3 kW only) * Requires M9C Includes option M130 *Includes option M131 J3 PROGRAM AND SENSE 1 90-250 VAC Remote Shutdown 14 TTL Shutdown
2 Shutdown Return 15 +12 VDC
3 OVP Program 16 1 mACurrent Source (OVP)
4 Remote/Local Status Indicator 17 OVP Indicator
5 Mode Status Indicator 18 Thermal S/DN Status
6 Ground 19 0-5V Voltage Monitor
7 0-5V Current Monitor 20 Remote Voltage Select