DA16200MOD RENESAS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 62

Technical content

Datasheet sections

  • 1 Terms and Definitions
  • 2 References
  • 3 Block Diagram
  • 4 Pinout
  • 4.1 Pin-out Description (37 pins)
  • 4.2 Pin Multiplexing
  • 5 Electrical Specification
  • 5.1 Absolute Maximum Ratings
  • 5.2 Recommended Operating Conditions
  • 5.3 Electrical Characteristics
  • 5.3.3 DC Parameters for RTC Block
  • 5.3.4 DC Parameters for Digital Wake-up
  • 5.4 Radio Characteristics
  • 5.4.1 WLAN Receiver Characteristics
  • 5.4.2 WLAN Transceiver Characteristics
  • 5.5 Current Consumption
  • 5.6 Radiation Performance
  • 5.7 ESD Ratings
  • 5.8 Clock Electrical Characteristics
  • 5.8.1 RTC Clock Source
  • 5.8.2 Main Clock Source
  • 6 Power Management
  • 6.1 Power On Sequence
  • 6.2 Low Power Operation Mode
  • 6.2.1 Sleep Mode
  • 6.2.2 Sleep Mode
  • 6.2.3 Sleep Mode
  • 7 Core System
  • 7.1 ARM Cortex-M4F Processor
  • 7.2 Wi-Fi Processor
  • 7.3 RTC
  • 7.3.1 Wake-up Controller

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 1 of 62 © 2023 Renesas Electronics General Description The DA16200MOD is a fully integrated Wi-Fi® module with ultra-low power consumption, best RF performance and easy development environment. Such low power operation can extend the battery life as longer as a year or more depending on the application. This module series included DA16200-00000A32, 40 MHz crystal oscillator, 32.768 KHz RTC clock, RF Lumped RF filter, 4 M-byte flash memory and chip antenna or u.FL connector. The DA16200MOD has chip antenna type (DA16200MOD-AAC4WA32) and u.FL connector type (DA16200MOD-AAE4WA32) for external antenna. The Module is built from the ground up for the Internet of Things (IoT) and is ideal for door locks, thermostats, sensors, pet trackers, asset trackers, sprinkler systems, connected lighting, video cameras, video door bells, wearables and other IoT devices. The modules certified Wi-Fi alliance for IEEE802.11b/g/n, Wi-Fi Direct, WPS functionalities and it has been approved by many countries including the United States (FCC), Canada (IC) and China (SRRC). Using the Wi-Fi Alliance transfer policy, the Wi-Fi Certifications can be transferred without being tested again. For more information on DA16200MOD, please refer to DA16200-00000A32 datasheet. Key Features ■ Module variants □ DA16200MOD-AAC4WA32 (chip Antenna) □ DA16200MOD-AAE4WA32 (u.FL cont.) ■ Highly integrated ultra-low power Wi-Fi® system module □ Sleep current: 3.5 uA, VBAT=3.3 V ■ Best RF Performance □ Tx Power: +19 dBm, 1 Mbps DSSS □ Rx Sensitivity: -98.5 dBm, 1 Mbps DSSS ■ Full offload: SoC runs full networking OS and TCP/IP stack ■ Wi-Fi processor □ IEEE 802.11b/g/n, 1x1, 20 MHz channel bandwidth, 2.4 GHz □ IEEE 802.11s Wi-Fi mesh □ Wi-Fi security: WPA/WPA2- Enterprise/Personal, WPA2 SI, WPA3 SAE, and OWE □ Vendor EAP types: EAP- TTLS/MSCHAPv2, PEAPv0/EAP- MSCHAPv2, PEAPv1, EAP-FAST, and EAP-TLS □ Operating modes: Station, SoftAP, and Wi-Fi Direct® Modes (GO, GC, GO fixed) □ WPS-PIN/PBC for easy Wi-Fi provisioning □ Connection manager for autonomous and fast Wi-Fi connections ■ Built-in 4-channel auxiliary ADC for sensor interfaces □ 12-bit SAR ADC: single-ended four channels □ Provides dynamic auto switching function ■ Supports various interfaces □ eMMC/SD expanded memory □ SDIO Host/Slave function □ QSPI for external flash control □ Three UARTs □ SPI Master/Slave interface □ I2C Master/Slave interface □ I2S for digital audio streaming □ 4-channel PWM □ Individually programmable, multiplexed GPIO pins □ JTAG and SWD ■ Wi-Fi Alliance certifications: □ Wi-Fi CERTIFIED™ b, g, n □ WPA™ - Enterprise, Personal □ WPA2™ - Enterprise, Personal □ WPA3™ - Enterprise, Personal ■ RF Regulatory certifications □ FCC, IC, CE, KC, TELEC, SRRC ■ CPU core subsystem

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 2 of 62 © 2023 Renesas Electronics □ Bluetooth coexistence □ Antenna switching diversity ■ Hardware accelerators □ General HW CRC engine □ HW zeroing function for fast booting □ Pseudo random number generator (PRNG) ■ Complete software stack □ Comprehensive networking software stack □ Provides TCP/IP stack: in the form of network socket APIs ■ Advanced security □ Secure booting □ Secure debugging using JTAG/SWD and UART ports □ Secure asset storage ■ Built-in hardware crypto engines for advanced security □ TLS/DTLS security protocol functions □ Crypto engine for key deliberate generic security functions: AES (128,192,256), DES/3DES, SHA1/224/256, RSA, DH, ECC, CHACHA, and TRNG ■ Power management unit □ On-Chip RTC □ Wake-up control of fast booting or full booting with minimal initialization time □ Supports three ultra-low power sleep modes □ Arm® Cortex®-M4F core w/ clock frequency of 30~160 MHz □ ROM: 256 KB, SRAM: 512 KB, OTP: 8 KB, Retention Memory: 48 KB ■ SPI flash Memory □ 32 M-bit / 4 M-byte ■ External Clock source □ 40 MHz crystal (± 25 ppm) for master clock (initial + temp + aging) □ 32.768 kHz crystal (± 250 ppm) for RTC clock ■ Supply □ Operating voltage: 2.1 V to 3.6 V (typical: 3.3 V) □ 2 Digital I/O Supply Voltage: 1.8 V / 3.3 V □ Black-out and brown-out detector ■ Module Dimensions □ 13.8 mm × 22.1 mm x 3.3 mm, 37 Pins, ■ Operating temperature range □ -40 °C to 85 °C

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 3 of 62 © 2023 Renesas Electronics

Applications

DA16200MOD is a full offload SoC for IoT Applications, such as: ■ Security systems ■ Door locks ■ Thermostats ■ Garage door openers ■ Blinds ■ Lighting control ■ Sprinkler systems ■ Video camera security systems ■ Smart appliances ■ Video door bell ■ Asset tracker System Diagram Figure 1: System Diagram

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 5 of 62 © 2023 Renesas Electronics

8.10 UART 43

8.11 PWM 47

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 8 of 62 © 2023 Renesas Electronics

1 Terms and Definitions

CRC Cyclic Redundancy Check DMA Direct Memory Access GPIO General Purpose Input/Output HW Hardware I2C Inter-Integrated Circuit I2S Inter-IC Sound IoT Internet of Things JTAG Joint Test Action Group LDO Low-dropout Regulator LLI Linked-List Item NVIC Nested Vectored Interrupt Controller NVRAM Non-Volatile RAM PLL Phase-locked Loop PRNG Pseudo Random Number Generator PWM Pulse Width Modulation QSPI Quad-lane SPI RTC Real-time Clock SAR ADC Successive Approximation Analog-to-Digital Converter SPI Serial Peripheral Interface SW Software SWD Serial Wire Debug UART Universal Asynchronous Receivers and Transmitter XIP eXecutein Place TAP Test Access Port

2 References

[1] ARM Cortex M4 Processor Technical Reference Manual [2] ITU-T O.150, General Requirements for Instrumentation for Performance Measurements on Digital Transmission Equipment, 1996 [3] Arm® TrustZone® CryptoCell-312, Revision r1p1, Software Integrators Manual [4] IEEE Standard 1149.1, Test Access Port and Boundary-Scan Architecture [5] DA16200_SDK_Programmer_Guide.pdf [6] AMBA AHB bus specification, Rev 3.0 https://developer.arm.com/documentation/ihi0033/bb

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 9 of 62 © 2023 Renesas Electronics

3 Block Diagram

Figure 2 shows the DA16200MOD hardware (HW) block diagram. Figure 2: Hardware Block Diagram Figure 3 shows the DA16200 SoC software (SW) block diagram. Figure 3: Software Block Diagram VBAT_3V3 VDD_DIO1 VDD_DIO2 RTC Control 40MHz Crystal 2.4GHzRF filter & Matching External Antenna type (u.FL connector) DA16200MOD-AAE Chip Antenna type DA16200MOD-AAC 32.768KHz Crystal UART For debugging 4ch 12bit ADC PIN Mux JTAG/ SDIO I2S I2C SD/eMMC GPIOs PWM UART Quad-SPI SPI 4Mbyte Serial flash User Application Home Appliance/Sensor Network/Door Lock/Light, IoT.

80211 Link Layer

DHCP/ DNS/ HTTP1.0 / HTTP1.1 TLS / DTLS NetX-APP TCP/UDP IP NetX-Duo Application Service

802.11 Upper MAC

802.11 Lower MAC

mDNS / xmDNS / DNS-SD / CoAP / Jason Afafa U upper Level CLI Handler Wi-Fi Supplicant

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 10 of 62 © 2023 Renesas Electronics The following descriptions are about the SW block diagrams.

  • Kernel layer ○ Real Time Operating System
  • The Wi-Fi layer is divided into four layers: ○ Lower MAC – SW module to control/handle HW Wi-Fi MAC/PHY and interfaces with Upper MAC layer ○ Upper MAC – SW module to control/handle Wi-Fi control/handle to interface with supplicant – Wi-Fi Link Layer: Interface layer between Upper MAC and supplicant – Supplicant: SW module to control/management to operate Wi-Fi operation ○ Network subsystem layer – Used to control/handle network operation – Main protocols are IP, TCP, and UDP – Other necessary protocols are supported ○ Security Layer – Crypto operation engine is ported to use crypto HW engine
  • TLS/TCP and DTLS/UDP APIs are supported to handle security operation: ○ User application layer – Variable sample codes are supported in SDK – sample codes use supported APIs – TCP Client/Server, UDP Client/Server, TLS Client/Server – HTTP/HTTPs download, OTA Update usage, and MQTT usage Customer applications can be included and implemented easily in SDK

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 11 of 62 © 2023 Renesas Electronics

4 Pinout

4.1 Pin-out Description (37 pins)

14 15 16 17 18 19 20 21 22 23 NC GND RTC_SENSOR RTC_WAKE_UP2 UART0_RXD UART0_TXD NC JTAG_TMS JTAG_TCLK GPIOC8 GPIOC7 GPIOC6 RTC_WAKE_UP RTC_PWR_KEY F_CS VDD_DIO2 F_IO1 F_IO0 F_IO2 F_IO3 F_CLK GPIOA10 GPIOA11 GPIOA9 GPIOA6 GPIOA5 GPIOA4 GPIOA3 GPIOA2 GPIOA1 GPIOA0 VDD_DIO1 VBAT_3V3 NC NC GPIOA7 GPIOA8 DA16200MOD series Figure 4: DA16200MOD 37 pins Pin-out Diagram (Top View)

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 12 of 62 © 2023 Renesas Electronics Table 1: Pin Description #Pin Pin Name Type Drive(mA) Reset State Description

1 NC NC NOT CONNECT

2 GND GND RF VDD

3 RTC_PWR_KEY DI RTC block enable signal

4 RTC_WAKE_UP DI RTC block wake-up signal

5 RTC_SENSOR DO Sensor control signal

6 NC NC NOT CONNECT

7 JTAG_TMS DIO 2/4/8/12 I-PU JTAG I/F, SWDIO

8 JTAG_TCLK DIO 2/4/8/12 I-PD JTAG I/F, SWCLK, General Purpose I/O

9 GPIOC8 DIO 2/4/8/12 I-PD General Purpose I/O

10 GPIOC7 DIO 2/4/8/12 I-PD General Purpose I/O

11 GPIOC6 DIO 2/4/8/12 I-PD General Purpose I/O

12 UART_TXD DO 2/4/8/12 O UART transmit data

13 UART_RXD DI 2/4/8/12 I UART receive data

14 RTC_WAKE_UP2 DI RTC block wake-up signal

15 VDD_DIO2 VDD Supply power for digital I/O

GPIOC6~GPIOC8, TMS/TCLK, TXD/RXD

16 F_CSN NC Flash Memory I/F

Available as a test point only, W25Q32JW is connected to DA16200 Internally

17 F_IO1 NC Flash Memory I/F (F_SI)

Available as a test point only, W25QJ32W is connected to DA16200 Internally

18 F_IO2 NC Flash Memory I/F (F_WP)

Available as a test point only, W25QJ32W is connected to DA16200 Internally

19 F_IO0 NC Flash Memory I/F (F_SO)

Available as a test point only, W25QJ32W is connected to DA16200 Internally

20 F_IO3 NC Flash Memory I/F (F_HOLD)

Available as a test point only, W25QJ32W is connected to DA16200 Internally

21 F_CLK NC External Flash Memory I/F

Available as a test point only, W25QJ32W is connected to DA16200 Internally

22 GPIOA11 DIO 2/4/8/12 I-PD General Purpose I/O

23 GPIOA10 DIO 2/4/8/12 I-PD General Purpose I/O

24 GPIOA9 DIO 2/4/8/12 I-PD General Purpose I/O

25 GPIOA8 DIO 2/4/8/12 I-PD General Purpose I/O

26 GPIOA7 DIO 2/4/8/12 I-PD General Purpose I/O

27 GPIOA6 DIO 2/4/8/12 I-PD General Purpose I/O

28 GPIOA5 DIO 2/4/8/12 I-PD General Purpose I/O

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 13 of 62 © 2023 Renesas Electronics #Pin Pin Name Type Drive(mA) Reset State Description

29 GPIOA4 DIO 2/4/8/12 I-PD General Purpose I/O

30 GPIOA3 AI/DIO 2/4/8/12 I-PD Aux.ADC input/General Purpose I/O 31 GPIOA2 AI/DIO 2/4/8/12 I-PD Aux.ADC input/General Purpose I/O 32 GPIOA1 AI/DIO 2/4/8/12 I-PD Aux.ADC input/General Purpose I/O 33 GPIOA0 AI/DIO 2/4/8/12 I-PD Aux.ADC input/General Purpose I/O

34 VDD_DIO1 VDD Supply power for digital I/O

35 VBAT_3V3 VDD Supply power for integrated power amplifier

36 NC NC NOT CONNECT

37 NC NC NOT CONNECT

4.2 Pin Multiplexing

This device provides various interfaces to support many kinds of applications. It is possible to control each pin according to the required application in reference to the pin multiplexing illustrated in Table 2. Pin control can be realized through register setting. This device can u se a maximum of 16 GPIO pins and each of the GPIO pins multiplexes signals of various functions. In particular, four pins from GPIOA0 to GPIOA3 multiplex analog signals, which also can be realized through register setting. Table 2: DA16200MOD Pin Multiplexing

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 14 of 62 © 2023 Renesas Electronics

5 Electrical Specification

5.1 Absolute Maximum Ratings

Table 3: Absolute Maximum Ratings Parameter Pins Min Max Units VBAT_3V3 35 -0.2 3.7 V VDD_DIO1 34 -0.2 3.7 V VDD_DIO2 15 -0.2 3.7 V Operating temperature range (TA) -40 +85 °C Storage temperature range -40 +125 °C

5.2 Recommended Operating Conditions

Table 4: Recommended Operating Conditions Parameter Pins Min Typ Max Units VBAT_3V3 35 2.1 3.6 V VDD_DIO1 34 1.62 3.6 V VDD_DIO2 15 1.62 3.6 V Operating temperature range (TA) -40 +85 °C

5.3 Electrical Characteristics

5.3.1 DC Parameters, 1.8 V IO Table 5: DC Parameters, 1.8 V IO Parameter Symbol Condition Min Typ Max Units Input Low Voltage VIL Guaranteed logic Low level VSS 0.3 × DVDD V Input High Voltage VIH Guaranteed logic High level 0.7 × DVDD DVDD V Output Low Voltage VOL DVDD=Min. VSS 0.2 × DVDD V Output High Voltage VOH DVDD=Min. 0.8 × DVDD DVDD V Pull-up Resistor RPU VPAD=VIH, DIO=Min. 32.4 kΩ Pull-down Resistor RPD VPAD=VIL, DIO=Min. 32.4 Note 1 DVDD = 1.8 V, VDD_DIO1, VDD_DIO2 Logic Level

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 15 of 62 © 2023 Renesas Electronics 5.3.2 DC Parameters, 3.3 V IO Table 6: DC Parameters, 3.3 V IO Parameter Symbol Condition Min Typ Max Units Input Low Voltage VIL Guaranteed logic Low level VSS 0.8 V Input High Voltage VIH Guaranteed logic High level 2.0 DVDD V Output Low Voltage VOL DVDD=Min. VSS 0.4 V Output High Voltage VOH DVDD=Min. 2.4 DVDD V Pull-up Resistor RPU VPAD=VIH, DIO=Min. 19.4 kΩ Pull-down Resistor RPD VPAD=VIL, DIO=Min. 16.0 Note 1 DVDD= 3.3 V, VDD_DIO1, VDD_DIO2 Logic Level

5.3.3 DC Parameters for RTC Block

There are several control pins in RTC block, see Section 7.3 RTC for detail. Table 7: DC Parameters for RTC block, 3.3 V VBAT Parameter Symbol Condition Min Typ Max Units Input Low Voltage VIL Guaranteed logic Low level VSS 0.6 V Input High Voltage VIH Guaranteed logic High level 2.2 VBAT V (RTC block: RTC_PWR_KEY, RTC_WAKE_UP, RTC_WAKE_UP2) Table 8: DC Parameters for RTC block, 2.1 V VBAT Parameter Symbol Condition Min Typ Max Units Input Low Voltage VIL Guaranteed logic Low level VSS 0.3 V Input High Voltage VIH Guaranteed logic High level 1.6 VBAT V (RTC block: RTC_PWR_KEY, RTC_WAKE_UP, RTC_WAKE_UP2)

5.3.4 DC Parameters for Digital Wake-up

Several GPIOs can be used for wake-up, see Section 7.3.1 Wake-up Controller for detail. To use Digital Wake-up, IO voltage should not be over VBAT. Table 9: DC Parameters for Digital Wake-up, 3.3 V VBAT & 1.8/3.3 V IO Parameter Symbol Condition Min Typ Max Units Input Low Voltage VIL Guaranteed logic Low level VSS 0.5 V Input High Voltage VIH Guaranteed logic High level 1.4 DVDD V (DVDD= 1.8/3.3V, VDD_DIO1, VDD_DIO2 Logic Level, DVDD should not be over VBAT)

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 16 of 62 © 2023 Renesas Electronics Table 10: DC Parameters for Digital Wake-up, 2.1 V VBAT & 1.8 V IO Parameter Symbol Condition Min Typ Max Units Input Low Voltage VIL Guaranteed logic Low level VSS 0.3 V Input High Voltage VIH Guaranteed logic High level 1.3 DVDD V (DVDD= 1.8V, VDD_DIO1, VDD_DIO2 Logic Level, DVDD should not be over VBAT)

5.4 Radio Characteristics

5.4.1 WLAN Receiver Characteristics

TA = +25 °C, VBAT = 3.3 V, CH1(2412 MHz) Table 11: WLAN Receiver Characteristics Parameter Condition Min Typ Max Units Sensitivity (8 % PER for 11b rates, 10 % PER for 11g/11n rates) 1 Mbps DSSS -99.5 -98.5 -96.5 dBm

2 Mbps DSSS -95 -94 -92

11 Mbps CCK -90 -89 -87

6 Mbps OFDM -91 -90 -88

9 Mbps OFDM -91 -90 -88

18 Mbps OFDM -89 -88 -86

36 Mbps OFDM -82 -81 -79

54 Mbps OFDM -76 -75 -73

MCS0(GF) -91 -90 -88 MCS7(GF) -73 -72 -70 Maximum input level (8 % PER for 11b rates, 10 % PER for 11g/11n rates) 802.11b -4 0 0 802.11g -10 -4 -3

5.4.2 WLAN Transceiver Characteristics

TA = +25 °C, VBAT = 3.3 V, CH1(2412 MHz) Table 12: WLAN Transmitter Characteristics Parameter Condition Min Typ Max Units Maximum Output Power measured form IEEE spectral mask and EVM 1 Mbps DSSS 16.5 19.0 20 dBm 2 Mbps DSSS 16.5 19.0 20 5.5 Mbps CCK 16.5 19.0 20 11 Mbps CCK 16.5 19.0 20 6 Mbps OFDM 15.5 18.0 19 9 Mbps OFDM 15.5 18.0 19 12 Mbps OFDM 15.5 18.0 19 18 Mbps OFDM 15.5 18.0 19 24 Mbps OFDM 14.5 17.0 18

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 17 of 62 © 2023 Renesas Electronics Parameter Condition Min Typ Max Units 36 Mbps OFDM 14.5 17.0 18 48 Mbps OFDM 13 15.5 16.5 54 Mbps OFDM 12 14.5 15.5 MCS0 OFDM 15.5 18.0 19 MCS7 OFDM 12 14.5 15.5 Transmit center frequency accuracy -25 +25 ppm

5.5 Current Consumption

TA = +25 °C, VBAT = 3.3 V, w/ CPU clock is 80 MHz. Table 13: Current Consumption in Active State Parameter Condition Min Typ Max Units ACTIVE TX 1 Mbps DSSS @ 19.0 dBm 260 280 320 mA 6 Mbps OFDM @ 18.0 dBm 240 260 300 54 Mbps OFDM @ 14.5 dBm 180 200 240 MCS7 @ 14.5 dBm 180 200 240 RX No signal (Note 1) 25 29 51 1 Mbps DSSS (Note 1) 26.5 30.5 53 1 Mbps DSSS 27 37.5 54 54 Mbps OFDM 29 38.5 54 MCS7 29 38.5 54 Note 1 Low Power Mode& CPU clock 30 MHz TA = +25 °C, VBAT = 3.3 V Table 14: Current Consumption in Low Power Operation Parameter Condition Min Typ Max Units Low Power Operation Sleep 1 0.2 µA Sleep 2 1.8 Sleep 3 3.5

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 18 of 62 © 2023 Renesas Electronics

5.6 Radiation Performance

Figure 5: TIS 3D Figure 6: TRP 3D

5.7 ESD Ratings

Table 15: ESD Performance Reliability Test Standards Test Conditions Result Human Body Model (HBM) ANSI/ESDA/JEDEC JS-001-2017 ± 2,000 V Pass Charge Device Mode (CDM) ANSI/ESDA/JEDEC JS-002-2018 ± 500 V Pass

5.8 Clock Electrical Characteristics

DA16200MOD is including two clock sources. One is the 32.768 kHz clock used by the RTC block, and the other is the 40 MHz clock for the internal processor and Wi-Fi system. More specifically, the

40 MHz clock is used as a source clock for the internal PLL while the PLL output is used for the

internal processor and Wi-Fi system block.

5.8.1 RTC Clock Source

The 32.768 kHz RTC clock source is necessary for the free-running counter in the RTC block. The RTC block of the SoC contains an internal 32.768 kHz RC oscillator as well, which is used as a clock for chip initialization before the external 32.768 kHz crystal reaches the stable time in the initial stage. It is necessary to convert it into an external clock for accurate clock counting after the initialization stage. This process is executed through the register setting.

5.8.2 Main Clock Source

DA16200MOD contains a crystal oscillator for the main clock source which supports the external crystal clock. Basically, the external clock is 40 MHz.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 19 of 62 © 2023 Renesas Electronics

6 Power Management

DA16200MOD has an RTC block which provides power management and function control for low power operation. In normal operation, the RTC block is always powered on when RTC_PWR_KEY is enabled.

6.1 Power On Sequence

The sequence after the initial switching from power-off to power-on is shown in Figure 7. The RTC_PWR_KEY of DA16200 is a pin that enables the RTC block. Once RTC_PWR_KEY is enabled after VBAT power is supplied, all the internal regulators are switched on automatically in the sequence pre-defined by the RTC block. Once RTC_PWR_KEY is switched on, LDOs for both XTAL and digital I/O are switched on shortly and then the DC-DC regulator is switched on according to the pre-defined interval. The enabling intervals can also be modified in the register settings after initial power-up. CLK_32K VBAT POWER_KEY IO Voltage 50% VBAT 50% IO 50% VBAT Figure 7: Power on Sequence Table 16: Power on Sequence Timing Requirements Name Description Min Typ Max Unit T0 VBAT power-on time from 10 % to 90% of VBAT ms T1 IO voltage and VCC supply 0 ms T2 RTC_PWR_KEY switch-on time from 50 % VBAT to 50 % POWER_KEY * Note 1 5*T0 ms T3 Internal RC oscillator wake-up time 217 µs Note 1 If the T0 = 10 ms to switch on VBAT, the recommended T2 is 50 ms for the safe booting operation. It would be externally controlled by MCU or it would be implemented using RC filter at the input of RTC_PWR_KEY. The recommended C is 470 nF or 1uF (not to exceed 1 uF) and R value is chosen to have T2 delay. For example, R and C values will be 82 kΩ and 1 uF when T0 = 10 ms.

6.2 Low Power Operation Mode

DA16200MOD provides three Sleep modes as low power operation modes.

6.2.1 Sleep Mode 1

Sleep mode 1 is an operational mode in which the RTC_PWR_KEY is not switched to high yet. The RTC_PWR_KEY is in the low state and the DA16200MOD is only supplied with VBAT power. With all the internal blocks off in Sleep mode 1, only the leakage current from a minimal number of internal blocks connected to VBAT remains.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 20 of 62 © 2023 Renesas Electronics

6.2.2 Sleep Mode 2

Sleep mode 2 is an operational mode in which the RTC_PWR_KEY is set to high and the RTC block is running. Sleep mode 2 is activated by setting RTC registers for controlling the power management unit via a command from the CPU. To switch Sleep mode 2 back to Sleep mode 1, RTC_PWR_KEY should be set to low. Changing the state of the device from Sleep mode 2 to an ACTIVE state happens in one of two ways:

  • The counter value that has been set by the CPU prior to entering Sleep mode 2 is reached.
  • An external wake-up event occurs via the RTC_WAKE_UP pin.

6.2.3 Sleep Mode 3

Sleep Mode 3 is a low power, fully connected Wi-Fi mode of operation. Sleep Mode 3 checks for incoming Wi-Fi network data traffic at regular intervals set by the user such as every one second, three seconds, five seconds, and so on. The exact time interval is programmable. Sleep Mode 3 is activated by software commands. See the SDK documentation for more information. A device can come out of Sleep Mode 3 and into a fully ACTIVE state before the next targeted wakeup time interval via a GPIO wakeup.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 21 of 62 © 2023 Renesas Electronics

7 Core System

7.1 ARM Cortex-M4F Processor

The Cortex-M4F processor is a low-power processor that features low gate count, low interrupt latency, low-cost debug, and includes floating point arithmetic functionality. The processor is intended for deeply embedded applications that require fast interrupt response features. The features of the Cortex-M4F processor in DA16200 are summarized below: ■ Operation clock frequency is up to 160 MHz ■ 32-bit ARM Cortex-M4F architecture optimized for embedded applications ■ Thumb-2 mixed 16/32-bit instruction set ■ Hardware division and fast multiplication ■ Includes Nested Vectored Interrupt Controller (NVIC) ■ SysTick timer provided by Cortex-M4F processor ■ Supports both standard JTAG (5-wire) and the low-pin-count ARM SWD (2-wire, TCLK/TMS) debug interfaces ■ Cortex-M4F is binary compatible with Cortex-M3 [7] For more information on the ARM Cortex-M4F, see ARM Cortex M4 Processor Technical Reference Manual [1].

7.2 Wi-Fi Processor

DA16200 includes an internal MCU (ARM Cortex-M4F) to completely offload the host MCU along with an 802.11 b/g/n radio, baseband, and MAC with a powerful crypto engine for a fast and secure WLAN and Internet connections with 256-bit encryption. It supports the station, SoftAP, and Wi-Fi Direct modes. It also supports WPA/WPA2 personal and enterprise security, WPA2 SI, WPA3 SAE, OWE, and WPS 2.0. It includes an embedded IPv4 and IPv6 TCP/IP stack.

7.3 RTC

Among the pins in DA16200MOD, four special pins are directly connected to the RTC block, which are RTC_PWR_KEY, RTC_GPO, RTC_WAKE_UP, and RTC_WAKE_UP2. Table 17: RTC Pin Description Pin Name Pin Number Description RTC_PWR_KEY 3 RTC_PWR_KEY represents a power key for the RTC block. When this pin is enabled, the RTC starts to work by following a pre- defined power-up sequence and eventually all the necessary power is supplied to all the sub-blocks including the main digital block in DA16200. When disabled, all blocks are powered off and this mode is defined as Sleep mode 1. Minimum leakage current in Sleep mode 1. RTC_SENSOR 5 This pin is an output and high level is 'VBAT'. It has three different functions.

  • GPO function: output value can be set as 1 or 0 via register setting. It can keep the value even in Sleep mode 2/3
  • Flash control function: when in Sleep mode, it becomes 0; when in Active mode, it is 1
  • Sensor wakeup function: when used in sensor wake-up function (Section 8.8.4), it provides a programmable periodic signal for an external device. Inside the RTC, there are registers for setting count values

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 22 of 62 © 2023 Renesas Electronics Pin Name Pin Number Description RTC_WAKE_UP 4 This pin is an input pin for receiving an external event signal from an external device like a sensor. The RTC block detects an external event signal via this pin and wakes up DA16200 from Sleep mode 2 or Sleep mode 3. RTC_WAKE_UP2 14 RTC block has a 36-bit real time counter. Its resolution is equal to one clock period of 32.768 kHz. The count value can be read via the register read command.

7.3.1 Wake-up Controller

The wake-up controller is designed to wake up DA16200MOD from a Sleep mode by an external signal. It detects an edge trigger of the wake-up signal and selects either the rising edge or the falling edge. Also, the wake-up signal must be maintained for at least 200 µs upon occurrence of transition on one side. When it comes to the source of wake-up, 11 digital I/Os in addition to the two pins directly connected to the RTC block can be used. Although up to 11 digital I/Os are available for use, the maximum number of digital I/Os that are simultaneously available is eight. Table 18 describes the digital I/Os that are available for simultaneous use. Table 18: Wake-up Sources Input Selection = 0 Input Selection = 1 GPIOA4 X GPIOA5 X GPIOA6 X GPIOA7 X GPIOA8 X GPIOA9 GPIOC6 GPIOA10 GPIOC7 GPIOA11 GPIOC8 For more on wake-up source selection, refer to input selection register: 0x50091008[25:16]. The wake-up controller is located in the RTC block. Several parameters can be set by RTC registers and they identify which pin is used to wake up the SoC by checking the status register after wake-up. DA16200MOD has another wake-up function using analog sources, which is described in Section 8.8.4. Using the Aux-ADC, DA16200 detects whether it exceeds the pre-defined threshold value. If it detects the wanted condition, it will wake up from a Sleep mode. Four ports (GPIOA[3:0]) are used for this function.

7.3.2 Retention I/O Function

DA16200 I/O supports a retention mode where the I/O cells retain their previous values at the core side inputs when in Sleep mode 2 or Sleep mode 3. Retention mode for the I/O cells is controlled by three bits in the retention enable register of the RTC block (0x5009_1018:BIT[27:24]). To maintain a specific GPIO value when in Sleep mode 2 or Sleep mode 3, the specific bit controlling the I/O power for it must be enabled in the retention enable register. For example, to maintain a HIGH value on GPIOA4 during Sleep mode 2 or Sleep mode 3, set the value of GPIOA4 to HIGH and also set the retention enable register BIT[25] to HIGH. A description of the retention enable register and the I/O power domains it controls can be found in Table 19.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 23 of 62 © 2023 Renesas Electronics Table 19: I/O Power Domain [25] DIO1 [26] DIO2 [27] FDIO GPIOA[11:4] GPIOC[8:6] F_CLK TCLK/TMS F_CSN UART0_RXD/UART0_TXD F_IO0 to F_IO3

7.4 Pulse Counter

7.4.1 Introduction

The pulse counter is a module which counts the number of rising or falling edges of input signals. And this counter module can run even in Sleep mode 2/3. It includes one 32-bit up-counter. The input channel can be chosen by register setting among the 11 digital I/Os. It also has a glitch filter which is designed to remove the unwanted trigger of an input signal.

7.4.2 Functional Description

Ext. Pad Mux. Mux_SEL Glitch Filter Edge Select Counter Int Gli_En Gli_Thresh Edge_Sel Count_En Count_Rst Int_Clr Int_Thresh IntPCLK Pulse Edge Pulse CountCLK_32kHz ㅣ ㅣ Figure 8: Pulse Counter Block Diagram

7.4.2.1 Input

Available input channels are described in Table 18. It uses the same input sources with the wake-up controller. By register setting, input channels can be selected among 11 digital I/Os.

7.4.2.2 Clock

The operation clock of the pulse counter is 32 kHz.

7.4.2.3 Counter

As described in Figure 8, the pulse counter is activated by several counter control signals. By register setting, input signals can be selected on either the rising edges or falling edges. In order to enable the glitch filter module, Gli_En and Gli_Thresh register values need to be set. The pulses whose cycles are shorter than the Gli_Thresh value are removed. The counter is a 32-bit up-counter and the counter value can be reset to zero by Count_Rst.

7.4.2.4 Interrupts

An interrupt occurs when the counter values reaches the Interrupt Threshold value (Int_Thresh). In Sleep mode, this interrupt can be used as a wake-up source.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 24 of 62 © 2023 Renesas Electronics

8 Peripherals

This section describes the peripherals that are supported by the DA16200MOD.

8.1 QSPI: Master with XIP Feature

QSPI master supports 4-line SPI communication with commercial flash memory devices and uses Motorola SPI-compatible interface among SPI communication modes. The highest communication speed is the same as the AMBA bus clock, and the speed is adjustable in integer multiples. The designed QSPI supports 4-/2-/1-line types depending on the purpose. These types should be combined. Especially when the 1-line communication mode is used, it can be used as the SPI master. QSPI master is an IP for communication between the flash memory and AMBA AHB bus and is designed to support XIP. The features of the QSPI master are summarized as follows: Serial Flash Interface:

  • SPI compatible serial bus interface ○ Configurable SPI I/O modes: – Single I/O mode – Dual I/O mode – Quad I/O mode ○ JEDEC Standard: JESD216B ○ 24-bit and 32-bit addressing ○ Supports to access flash with XIP mode – Read access without command – Read access without address and command ○ Programmable SPI clock phase and polarity ○ Maximum number of SPI CS is four that can be operated AMBA Slave Interface
  • Compliance to the AMBA AHB bus specification, Rev 3.0 [6]
  • Direct code execution: directly addressable access without additional driver software
  • Supports single and incrementing burst transfer (SINGLE, INCR, INCR4, INCR8, INCR16)
  • Supports byte, half-word, and word transaction
  • AMBA slave interface is optional to access configuration and status registers
  • Simple timer is used to check the completion time of flash operation
  • XIP path of QSPI master supports HW remapping function to execute selected boot imag e for over-the-air programming (OTA) AMBA Master Interface
  • Compliance to the AMBA AHB bus specification, Rev 3.0 [6]
  • Supports DMA operation to access serial flash devices ○ Automatic copy of code image from serial flash to system RAM ○ Automatic programming of code image from system RAM to serial flash
  • Performs a mem-to-mem copy in units of 32 bits, regardless of the address and length
  • Supports single and incrementing burst transfer (SINGLE, INCR, INCR4, INCR8, INCR16)
  • Supports byte, half-word, and word transaction Figure 9 shows the QSPI Master Block Diagram.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 26 of 62 © 2023 Renesas Electronics

8.2 SPI Master

QSPI can use the SPI master by means of single line interface. Table 21 shows the pin definition of the SPI master interface. SPI signal timing is the same as QSPI. To use DA16200MOD as an SPI master, the CSB signal can be used with any of the GPIO pins. CSB [3:1] can be selected from GPIO special function by setting the registers in the GPIO. Table 21: SPI Master Pin Configuration Pin Name Pin Number I/O Function Name GPIOx O E_SPI_CSB[3:1] GPIOA6 27 O E_SPI_CSB[0] GPIOA7 26 O E_SPI_CLK GPIOA8 25 I/O E_SPI_MOSI or E_SPI_D[0] GPIOA9 24 I/O E_SPI_MISO or E_SPI_D[1] GPIOA10 23 I/O E_SPI_D[2] GPIOA11 22 I/O E_SPI_D[3] E_SPI_CSB E_SPI_CLK E_SPI_D[3:0] TCLK.ON TDO.DLY TDI.SU TCSB.OF F Figure 11: SPI Master Timing Diagram (Mode 0) Table 22: SPI Master Timing Parameters Parameter Symbol Min Typ Max Unit QSPI_CLK frequency FCLK 5 60 MHz QSPI_CLK clock duty 50 % 1st CLK active rising transition time TCLK.ON 0.5 × TCLK TCLK (Note 1) ns QSPI_CSB non-active rising transition time TCSB.OFF 0 TCLK ns QSPI_D[3:0] input setup time TDI.SU 6 ns QSPI_D[3:0] output delay time TDO.DLY 2 ns Note 1 TCLK = (FCLK× 106)-1 seconds

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 27 of 62 © 2023 Renesas Electronics

8.3 SPI Slave

SPI slave interface is a half-duplex connection for an external host to control the DA16200. The range of SPI clock speed is based on the internal bus clock speed and can be calculated using: spi clock = system clock/N where N is an integer divider such as 1,2,3,4,5,6,.... The SPI slave supports both the burst mode and non-burst mode. In the burst mode, SPI_CSB remains active from the start to the end of communication. In the non-burst mode, SPI_CSB remains active at every eight bits. SPI Signals Address Decoder Command Decoder Data Decoder APB bus Controller Figure 12: SPI Slave Block Diagram Communication protocols of the SPI slave interface use either 4-byte or 8-byte control signals. Between the two available communication protocols, the CPU chooses one before initiating the control. Figure 13 and Figure 14 shows the 8-byte and 4-byte control types. SPI_CSB SPI_CLK SPI_MOSI A [ 31 : 24 ] A [ 7 : 0 ]A [ 15 : 8 ]A [ 23 : 16 ] C [ 7 : 0 ] L [ 23 : 16 ] L [ 15 : 8 ] L [ 7 : 0 ] D [ 7 : 0 ] D [ 15 : 8 ] D [ 23 : 16 ] D [ 31 : 24 ] Figure 13: 8-byte Control Type SPI_CSB SPI_CLK SPI_MOSI A [ 15 : 8 ] L [ 7 : 0 ]C [ 7 : 0 ]A [ 7 : 0 ] D [ 7 : 0 ] D [ 15 : 8 ] D [ 23 : 16 ] D [ 31 : 24 ] Figure 14: 4-byte Control Type The 8-byte control type uses 4-byte address, 1-byte control, and 3-byte length. The 4-byte address displays the address of registers subject to internal access. The 1-byte control is for communication control and 3-byte length shows the length of data subject to continuous access in bytes. Hence, when the 8-byte control type is applied, the maximal length of data subject to continuous access is 16 MB. The 4-byte control type uses 2-byte address, 1-byte control, and 1-byte length. The 2-byte address displays the address of registers subject to internal access. The 1-byte control is for communication control and 1-byte length shows the length of data subject to continuous access in bytes. Since the 32-bit address map is used internally, the 2-byte address is not enough to express everything. Thus, the upper 2-byte base address is designated, and then the lower 2-byte address is used. Table 23 and Table 24 shows the meaning of each bit in the 1-byte control in the 8-byte control type and the 4-byte control type, respectively.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 28 of 62 © 2023 Renesas Electronics Table 23: Control Field of the 8-byte Control Type Control Bit Abr. Description 7 Auto Inc. 1 = Internal Address auto-increment 0 = Address fixed

6 Read/Write 1 = Read 0 = Write

5:0 Not used. Set all bits to ‘0’ Table 24: Control Field of the 4-byte Control Type Control Bit Abr. Description 7 Auto Inc. 1 = Internal address auto-increment 0 = Address fixed

5 Common 1 = Refer base address as common area 0 = Refer base address

4 Length section 1 = Refer to register value 0 = Refer to length field

3:0 Length[12:8] Length field upper Table 25 shows the pin definition of the SPI slave interface. Table 25: SPI Slave Pin Configuration Pin Name Pin Number I/O Function Name GPIOA2 31 I SPI_CSB GPIOA6 27 I GPIOA3 30 I SPI_CLK GPIOA7 26 I GPIOA1 32 I SPI_MOSI GPIOA9 24 I GPIOA11 22 I GPIOA0 33 O SPI_MISO GPIOA8 25 O GPIOA10 23 O Figure 15 shows the timing diagram for the SPI slave. SPI_CSB SPI_CLK (CPOL=0) SPI_MOSI SPI_MISO TSCLKL TMSU TMHD TSSU MSB LSB LSB TSCLKHTSCLKOFF TSCLKON TTR TCSBOFF SPI_CLK (CPOL=1) TSCLKLTSCLKH Figure 15: SPI Slave Timing Diagram

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 29 of 62 © 2023 Renesas Electronics Table 26 lists the timing parameters for the SPI slave. Table 26: SPI Slave Timing Parameters Parameter Symbol Min Typ Max Unit SCLK frequency FSCLK - - 50 MHz SCLK clock duty 40 % Non active duration TSCLKOFF 400 - - ns 1st CLK active rising transition time TSCLKON TSCLKL(CPOL=0) TSCLKH (CPOL=1) - - ns CSB non active rising transition time TCSBOFF TSCLKH (CPOL=0) TSCLKL (CPOL=1) - - ns MOSI setup time TMSU 8 - TSCLK (Note 1) ns MOSI hold time TMHD 8 - TSCLK ns MISO delay time TSSU - - 8 ns MISO transition time(10% to 90% transition) TTR - 4 5 ns Note 1 TSCLK = 0.5 × (FSCLK x 106)-1 second

8.4 SDIO

SDIO is a full/high speed card suitable for memory card and I/O card applications with low power consumption. The full/high speed card supports SPI, 1-bit SD, and 4-bit SD transfer modes at the full clock range of 0 to 50 MHz. To be compatible with the serviceable SDIO clock, the internal BUS clock needs to be set to minimum 50 MHz. The CIS and CSA area is located inside the internal memory and the SDIO registers(CCCR and FBR) are programmed by the SD host. Command Decoder APB bus Interface REG. Control Fn0 / Fn1 Decoder DAT Decoder Response Generator CRC Generator 2 port Memory DMA Controller Figure 16: SDIO Slave Block Diagram Table 27 shows the pin definition of the SDIO interface. The GPIOA4 and GPIOA5 pins are set to SDIO CMD and CLK by default. If SDIO initialization is performed and SDIO communication is enabled, SDIO data pin setting is performed automatically. In other words, when the SDIO communication is detected, the pin used as the SDIO data among the GPIO pins is automatically activated in the SDIO use mode. However, the auto setting function is not supported for the F_xxx pin used as the flash function.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 31 of 62 © 2023 Renesas Electronics DA16200 SD_CLK SD_CMD SD_D0 SD_D1 SD_D2 SD_D3 Rp Rp Rp Rp Rp VDD_IO Figure 18: SDIO Pull-up Resistor Pull-up resistor values can be different from the board layout.

8.5 I2C Interface

8.5.1 I2C Master

DA16200MOD includes an I2C master module. Three ranges of clock speed are supported: standard (100 kHz), fast (400 kHz), and high (1.0 MHz) speed mode. Table 29 shows the pin definition of the I2C master interface. Table 29: I2C Master Pin Configuration Pin Name Pin Number I/O Function Name GPIOA1 32 O I2C_CLK GPIOA5 28 O GPIOA9 24 O GPIOA0 33 I/O I2C_SDA GPIOA4 29 I/O GPIOA8 25 I/O

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 33 of 62 © 2023 Renesas Electronics

8.5.2 I2C Slave

I2C slave interface supports the control of DA16200MOD by an external host. Pin mux condition is defined in Table 31. Three ranges of clock speed are supported: standard (100 kHz), fast (400 kHz), and high (1.0 MHz) speed mode. Table 31: I2C Slave Pin Configuration Pin Name Pin Number I/O Function Name GPIOA1 32 I I2C_CLK GPIOA3 30 I GPIOA5 28 I GPIOA7 26 I GPIOA0 33 I/O I2C_SDA GPIOA2 31 I/O GPIOA4 29 I/O GPIOA6 27 I/O Figure 20 shows the I2C slave timing diagram. THD;STA S SDA SCL TR TSU;DAT THIGH TLOW TR THD;DAT TVD;ACK cont. ... ... SDA SCL cont. ... ... TSU;STA THD;STA Sr TBUF P TSU;STO S Figure 20: I2C Slave Timing Diagram Table 32 lists the I2C slave timing parameters. Table 32: I2C Slave Timing Parameters Parameter Symbol Fast Mode High Speed Mode Unit Min Max Min Max SCL clock frequency FSCLK 0 400 0 1000 (Note 2) kHz Clock Duty (Note 1) 40 60 40 60 % Hold time of START THD;STA 0.6 - 0.26 - μs Low period of the SCL clock TLOW 1.3 - 0.5 - μs

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 34 of 62 © 2023 Renesas Electronics Parameter Symbol Fast Mode High Speed Mode Unit Min Max Min Max High period of the SCL clock THIGH 0.6 - 0.26 - μs Setup time for START condition TSU;STA 0.6 - 0.26 - μs Data hold time THD;DAT 0 - 0 - μs Data setup time TSU;DAT 100 - 50 - ns Rise time of both SDA and SCL TR 20 300 - 120 ns Setup time for STOP condition TSU;STO 0.6 - 0.26 - μs Data valid acknowledge time TVD;ACK - - - - μs Buffer free time between START and STOP condition TBUF 1.3 - 0.5 - μs Note 1 Clock duty ratio = (THIGH /TSCLK) × 100[%], TSCLK = 1/FSCLK Note 2 Max. clock = 1.0 MHz (clock period = 1000 ns)

8.5.3 Interface Pull-up

I2C interface requires pull-up resistors to be connected between the signal lines and the supply to enable communication. DA16200 I2C_CLK I2C_SDA Rp Rp VDD_IO Figure 21: I2C Pull-up Resistor Pull-up resistor values can be different from the board layout.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 35 of 62 © 2023 Renesas Electronics

8.6 SD/SDeMMC

The SD/eMMC host IP provides the function for DA16200MOD to access SD or eMMC cards. This SD/eMMC host IP only supports a 4-bit data bus and the maximum clock rate is 50 MHz. The maximum data rate is 25 MB/s (200 Mbps) under the 4-bit data bus and 50 MHz clock. SD/eMMC pin mux condition is defined in Table 33. Table 33: SD/eMMC Master Pin Configuration Pin Name Pin Number I/O Function Name GPIOA4 29 I/O SD/eMMC_CMD GPIOA5 28 O SD/eMMC_CLK GPIOA9 24 I/O SD/eMMC_D0 GPIOA8 25 I/O SD/eMMC_D1 GPIOA7 26 I/O SD/eMMC_D2 GPIOA6 27 I/O SD/eMMC_D3 GPIOA10 23 I SD/eMMC_WRP GPIOA1 32 I

8.6.1 Block Diagram

Figure 22 shows the block diagram of SD/eMMC host IP and it includes the control register, clock control, command/response pipe, data pipe, and AHB master interface blocks. AHB Slave Control Registers Data Pipe AHB Master Clock Control HCLK HCMD HDATA[3:0] CMD/RSP Pipe AHB FIFO Figure 22: SD/eMMC Block Diagram Figure 23 shows the timing diagram for the SD/eMMC master. SD/eMMC_CLK SD/eMMC_D[3:0] SD/eMMC_CMD TCO.DLY TDO.DLY TCI.SU TDI.SU Figure 23: SD/eMMC Master Timing Diagram

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 36 of 62 © 2023 Renesas Electronics Table 34 lists the timing parameters for the SD/eMMC master. Table 34: SD/eMMC Master Timing Parameters Parameter Symbol Min Typ Max Unit SD/eMMC_CLK frequency FSCLK - - 50 MHz SD/eMMC_CLK clock duty 50 % SD/eMMC_CMD input setup time TCI.SU 8 ns SD/eMMC_CMD output delay time TCO.DLY 3 ns SD/eMMC_D[3:0] input setup time TDI.SU 8 ns SD/eMMC_D[3:0] output delay time TDO.DLY 8 ns

8.7 I2S

DA16200MOD provides an I2S interface. Once an I2S block receives audio data through the DMA, it sends audio data to the external port according to the I2S standard. To use the external DAC, output through the GPIO port is possible through the register setting according to the pin configuration (Table 35). The I2S also provides a receive function. However, I2S transmission and reception functions cannot be used at the same time. The transmit and receive functions can be selected by register setting. If the I2S signal is input from outside after the reception function is set, the audio signal can be decoded, stored in the FIFO, and read out through the DMA. The decodable reception function provides 8/16/24/32-bit modes and can receive either mono or stereo. Using the I2S clock divider register, the internal PLL clock can be variably applied to the I2S clock source. The available I2S clock source is 24/48 MHz. There is also a way to apply the I2S clock source directly from outside using the GPIO pin. For accurate I2S audio sampling, I2S clock source can be input to external GPIO pins. It needs to select the GPIO pin setting as the I2S clock input and apply appropriate clock source. The available I2S clock pins are shown in Table 35. Table 35: I2S Pin Configuration Pin Name Pin Number I/O Function Name GPIOA1 32 O I2S_MCLK GPIOA5 28 O GPIOA9 24 O GPIOA0 33 O I2S_BCLK GPIOA4 29 O GPIOA8 25 O GPIOA3 30 O I2S_LRCK GPIOA7 26 O GPIOA2 31 I/O I2S_SDO GPIOA6 27 I/O GPIOA3 30 I I2S_CLK_IN GPIOA10 23 I

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 37 of 62 © 2023 Renesas Electronics

8.7.1 Block Diagram

I2S has the following features: ■ Master Clock Mode only ■ I2S Data pin can work in either input mode or output mode ■ Clock source can be "internal 480 MHz/N" (currently using 24 MHz) or "external clock source" ■ Max Sampling Rate: 48 KHz ■ Mono/Stereo Mode Figure 24: I2S Block Diagram

8.7.2 I2S Clock Scheme

The I2S uses a 24 MHz clock as default from the RF reference clock (40 MHz), so it can support 46.875 KHz of sampling rate. External clock sources are needed to support the standard sampling rate. See Table 36. Figure 25: I2S Clock Scheme

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 38 of 62 © 2023 Renesas Electronics Table 36: I2S Clock Selection Guide Parameter Units LRCK Fs 8 12 16 24 32 44.1 46.875 48 KHz Clk Div2 N (=1,2,3…) 6 4 3 2 2 1 1 1 I2S_CLK (Internal PLL)

24.576 MHz

To confirm the exact LRCK operation, drive the Clock source at I2S_CLK.

8.7.3 I2S Transmit and Receive Timing Diagram

I2S output is possible in the following three modes. The main clock (MCLK) always outputs in 512×fs.

  • I2S Mode LRCK SCLK SDATA MSB -1 -2 -3 +3 +2 +1 LSB MSB -1 -2 -3 -4 +3 +2 +1 LSB Left Channel Right Channel Figure 26: I2S Timing Diagram
  • Left Justified Mode LRCK SCLK SDATA MSB -1 -2 -3 +3 +2 +1 LSB MSB -1 -2 -3 -4 +3 +2 +1 LSB Left Channel Right Channel Figure 27: Left Justified Mode Timing Diagram
  • Right Justified Mode LRCK SCLK SDATA 15 14 2 1 0 Left Channel Right Channel 13 15 14 2 1 013 Figure 28: Right Justified Mode Timing Diagram

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 40 of 62 © 2023 Renesas Electronics

8.8 ADC (Aux 12-bit)

8.8.1 Overview

DA16200MOD includes a high precision, ultra-low power, and wide dynamic range SAR ADC with a 12-bit resolution. It has a 4-channel single-end ADC. Analog input is measured by four pins from GPIOA0 to GPIOA3, and pin selection is changed through the register setting. Figure 31 shows the control block diagram. ADC 12b Max : 1Ms Counter 16-bit ADC Controller Ready CH_SEL SWITCH VI_N[1] VI_N[2] VI_N[3] VI_N[4] Switch Figure 31: ADC Control Block Diagram

8.8.2 Timing Diagram

The input is digitized at a maximum of 1.0 Msps throughput rate. And the maximum input clock rate is 15 MHz. Figure 32 shows the conversion timing, and Table 39 describes DC specifications. Figure 32: 12-bit ADC Timing Diagram CLK 15MHz SAMPLE CLKOUT AUXADC_EN OSC_EN D<11:0> 15*CLK N 15*CLK N+1 15*CLK N+2 15*CLK N+3 15*CLK N+4 N N+1 N+2 N+3 15*CLK

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 41 of 62 © 2023 Renesas Electronics Table 39: DC Specification Description Min Typ Max Unit Resolution 4 12 12 Bits Max clock input 15 MHz Conversion frequency 1 MHz Accuracy:

  • SNR
  • SNDR
  • 61.7
  • 67.2
  • dB
  • dB Analog input range 0 1.4 V

8.8.3 DMA Transfer

There are four ADC channel settings available. Once the input data of each channel reaches the FIFO level, it is possible to read the data through the DMA path.

8.8.4 Sensor Wake-up

DA16200MOD provides an external sensor wake-up function using the analog input signal through this Aux ADC. Even in Sleep mode 2/3, it detects the change of external analog signal, wakes up from a Sleep mode 2/3, and converts DA16200MOD into a normal operation. This function can be used in up to four channels. Also, when multiple external sensors are used, it detects analog signals while changing the channel automatically. For example, if it sets all four channels as input sources which have their threshold register respectively, in measures the channels sequentially from 0 to 3. If one of the four values exceed the allowed range of values set by the threshold register, DA16200MOD is awaken from Sleep mode 2/3. The setting value of input change can be of two types, over threshold and under threshold.

8.8.5 ADC Ports

Table 40 shows the pin definition of the ADC. Table 40: ADC Pin Configuration Pin Name Pin Number I/O Function Name GPIOA3 30 A Analog signal GPIOA2 31 A Analog signal GPIOA1 32 A Analog signal GPIOA0 33 A Analog signal

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 42 of 62 © 2023 Renesas Electronics

8.9 GPIO

All digital pads can be used as GPIO, and each GPIO port is mixed with a multi-functional interface. The GPIO features of DA16200MOD are listed below:

  • Input or output lines in a programmable direction
  • Word and half word read/write access
  • Address-masked byte writes to facilitate quick bit set and clear operations
  • Address-based byte reads to facilitate quick bit test operations
  • Maskable interrupt generation based on input value change
  • Possible to be output signal of PWM[3:0], external interrupt, QSPI_CSB[3:1], RF_SW[1:0], and UART_TXDOE[2:0] on the GPIO pins: ○ It provides special functions for GPIO pin use. PWM [3:0], external interrupt, QSPI_CSB [3:1], RF_SW [1:0], and UART_TXDOE [2:0] signals can be output by selecting unused pins among the GPIO pins. It is possible to select the function to be output from the GPIO register setting and select the remaining GPIO pin without using it to output the specific function to the desired GPIO pins

8.9.1 Antenna Switching Diversity

DA16200MOD-AAE4WA32 (u.FL connector type module) provides the antenna switching diversity function for performance improvement in multi-path environment. Phy block measures the RSSI of each antenna and selects the antenna with the largest RSSI. The selected antenna is also used for transmission. To use this function, an external switching element is required, and switching control is performed through the GPIO. Two GPIOs can be used for switching control, and any unused pins among the GPIO pins can be selected for this purpose. The control signal can be changed by register setting to suit the external switching device. Figure 33: Antenna Switching Internal Block Diagram If the Antenna Switching Diversity function is enabled, the function is automatically done by PHY hardware block. The basic operation scheme is as follows:

  • Antenna's RSSI decision is made for 11b PPDU, except for 11g/n PPDU
  • When PHY hardware detects the existence of 11b PPDU, it stores RSSI
  • After it switch to another antenna, the RSSI stored and decision is made which antenna has better RSSI
  • This operation is done during 11b PPDU's preamble duration to protect corruption of 11b PPDU data reception
  • The decided antenna is not changed until there is a new 11b PPDU RF Switch FC9050 GPIO ANT Antenna1 Antenna2 DA16200MOD-AAE RF Switch

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 43 of 62 © 2023 Renesas Electronics Figure 34: Antenna Switching Timing Diagram For reference, this antenna switching diversity is different from MRC. (Maximum Ratio Combining)

8.10 UART

DA16200MOD provides 3 UARTs, features of which are described below:

  • Programmable use of UART (UART1 and UART2)
  • Compliance to the AMBA AHB bus specification [6] for easy integration into SoC implementation
  • Supports both byte and word access for reduction of bus burden
  • Supports both RS-232 and RS-485
  • Separate 32×8 bit transmit and 32×12 bit receive FIFO memory buffers to reduce CPU interrupts
  • Programmable FIFO disabling for 1-byte depth
  • Programmable baud rate generator
  • Standard asynchronous communication bits (start, stop and parity), which are added prior to transmission and removed on reception
  • Independent masking of transmit FIFO, receive FIFO, and receive timeout
  • Supports for DMA
  • False start bit detection
  • Programmable flow control (CTS/RTS, UART1)
  • Fully programmable serial interface characteristics: ○ Data can be of 5,6,7, or 8 bits ○ Even, odd, stick, or no-parity bit generation and detection ○ 1- or 2- stop bit generation ○ Baud rate generation

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 44 of 62 © 2023 Renesas Electronics Figure 35: DA16200 UART Block Diagram

8.10.1 RS-232

As the serial communication between the UART and the selected device is asynchronous, additional bits (start and stop) are inserted to the data line to indicate the beginning and end. By these bits, two devices can be synchronized. This structure of serial data accompanied by start and stop bits is referred to as a character, as shown in Figure 36. Data Start Bit Time Data bits 5 - 8 Parity 1- or 2-Stop One Character Figure 36: Serial Data Format

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 45 of 62 © 2023 Renesas Electronics An additional parity bit may be added to the serial character. This bit appears between the last data bit and the stop bit(s) in the character structure. It provides the UART with the ability to perform simple error checking on the received data. The UART Line Control Register is used to control the serial character characteristics. The individual bits of the data word are sent after the start bit, starting with the least significant bit (LSB). These are followed by the optional parity bit, followed by the stop bit(s), which can be 1 or 2. Serial Data In 8 16 16 Start Data Bit 0 (LSB) Data Bit 1 Figure 37: Receiver Serial Data Sampling Points All the bits in the transmission are transmitted for exactly the same time duration. This is referred to as a Bit Period or Bit Time. One Bit Time equals 16 baud clocks. To ensure stability on the line, the receiver samples the serial input data at approximately the mid-point of the Bit Time, once the start bit has been detected. As the exact number of baud clocks that each bit was transmitted for is known, calculating the mid-point for sampling is not difficult, that is every 16 baud clocks after the mid-point sample of the start bit. Figure 37 shows the sampling points of the first couple of bits in a serial character.

8.10.2 RS-485

DA16200MOD UART supports RS-485. UART485EN register (0x054) is required to be assigned to one to enable the RS-485. In order to use RS-485, additional signal (UARTTXDOE) is required to notice TXD intervals. This signal can be an output by selecting any unused pins among the GPIO pins. Figure 38: UARTTXDOE Output Signal for UART RS-485

8.10.3 Baud Rate

UART clock frequency (FUARTCLK) is fixed to 80 MHz. Baud Rate Divisor can be calculated as (FUARTCLK / (16 x Baud Rate)). Baud Rate Divisor is comprised of the integer part (UART_INTBRDIV) and fractional part (UART_FRABRDIV). The maximum baud rate of DA16200 UART is 2.5 MBaud. The following example shows how to calculate the divisor value. Example: If the required baud rate is 921600 with 80 MHz FUARTCLK, the Baud Rate Divisor becomes (8 x 107) / (16 x 921600) = 5.425. This means the integer value is 5 and the fractional value is 0.425. Then, the fraction part becomes integer ((0.425 x 64) + 0.5) = 27.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 46 of 62 © 2023 Renesas Electronics Then, generated baud rate divider is 5 + 27/64 = 5.422. Finally, generated baud rate becomes (8 x 107) / (16 x 5.422) = 922169. And the error between required baud rate and generated baud rate is (922169 – 921600) / 921600 x100 = 0.062%.

8.10.4 Hardware Flow Control

Hardware flow control feature is fully selectable, and serial data flow is controlled by using nUARTRTS output and nUARTCTS input signals. Figure 39 shows how two different UART can communicate using hardware flow control. Figure 39: UART Hardware Flow Control When RTS flow control is enabled, nUARTRTS signal is asserted until the receive FIFO is filled up to programmed level. When CTS flow control is enabled, transmitter can transmit the data when nUARTCTS signal is asserted. CTSEn (CTS enable) and RTSEn (RTS enable) bits are determined by 14th (RTS) and 15th bit (CTS) of UARTCR register. Table 41: Control bits to enable and disable hardware flow control CTSEn RTSEn Description 1 1 Both RTS and CTS flow control are enabled 1 0 Only CTS flow control is enabled 0 1 Only RTS flow control is enabled 0 0 Both RTS and CTS flow control are disabled

8.10.5 Interrupts

DA16200MOD UART block provides five interrupt signals by separate interrupt lines. Each interrupt conditions are Modem Status, Receive FIFO Request, Transmit FIFO Request, Receive Timeout and Reception Error. These conditions are logically OR'ed to provide a single combined interrupt, UARTINTR. Table 42 shows the interrupt signals. Table 42: UART Interrupt Signals Signal Name Description UARTMSINTR UART Modem Status Interrupt UARTRXINTR UART Receive FIFO Interrupt

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 47 of 62 © 2023 Renesas Electronics Signal Name Description UARTTXINTR UART Transmit FIFO Interrupt UARTRTINTR UART Receive Timeout Interrupt UARTEINTR UART Error Interrupt UARTINTR UART Interrupt. Five Interrupt signals are combined by OR function

8.10.6 DMA Interface

DA16200MOD UART block can generate DMA request signals with register settings by using DMA interrupt generator module to connect to DA16200 DMA Controller (DMA1). DMA operation of the UART is controlled using DMA Control Register. DA16200MOD UART provides four DMA signals and receives two DMA signals, two signals to transmit (TXDMASREQ, TXDMABREQ) which are cleared by TX clear signal (TXDMACLR) and two signals to receive (RXDMASREQ, RXDMABREQ), which are cleared by RX clear signal (RXDMACLR). When the DMA interface is not used, the TXDMACLR and RXDMACLR lines should be connected to a logic ‘0’. Table 43 shows the pin definition of the UART interface. Table 43: UART Pin Configuration Pin Name Pin Number I/O Function Name UART0_RXD 13 I UART0_RXD UART0_TXD 12 O UART0_TXD GPIOA7 26 I UART1_RXD GPIOA5 28 I GPIOA3 30 I GPIOA1 32 I GPIOA6 27 O UART1_TXD GPIOA4 29 O GPIOA2 31 O GPIOA0 33 O GPIOA5 28 I UART1_CTS GPIOA4 29 O UART1_RTS GPIOA11 22 I UART2_RXD GPIOC7 10 I GPIOA10 23 O UART2_TXD GPIOC6 11 O

8.11 PWM

Pulse Width Modulation (PWM) is a modulation technique used to encode a message into a pulse signal. The blocks are designed to adjust output pulse duration by the CPU bus clock (HCLK). Figure 40 shows the structure of the PWM block.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 48 of 62 © 2023 Renesas Electronics AHB Bus Matrix PWM OUTPWM Block 0 Counter (Period) Register Counter (High Duty) PWM Block 1 Counter (Period) Register Counter (High Duty) PWM Block 2 Counter (Period) Register Counter (High Duty) PWM Block 3 Counter (Period) Register Counter (High Duty) PWM OUT PWM OUT PWM OUT HCLK Counter Register AHB Bus Figure 40: PWM Block Diagram Table 44 shows the pin definition of the PWM interface. GPIOx means that PWM signals can go out through any GPIO pins via register setting. Table 44: PWM Pin Configuration Pin Name Pin Number I/O Function Name GPIOx PWM[3:0] output

8.11.1 Timing Diagram

Table 45 shows the relation between the internal bus clock and PWM output wave patterns. Figure 41 show the conversion timing diagram. ‘a’ and ‘b’ can be adjusted through the register setting, and PWM wave patterns vary depending on the ratio. ‘a’ controls the high width of pulses (nCycle High), while ‘b’ controls the general cycle (nCycle Period). PWM a b BUS CLK Figure 41: PWM Timing Diagram Table 45: PWM Timing Diagram Description Time Description a Bus Clock Period × (nCycle High + 1) b Bus Clock Period × (nCycle Period + 1)

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 49 of 62 © 2023 Renesas Electronics

8.12 Debug Interface

DA16200MOD supports both IEEE Standard 1149.1 JTAG (5-wire) and the low-pin-count ARM SWD (2-wire, TCLK/TMS) debug interfaces. The SWD protocol can handle the same debug features as the JTAG. The JTAG port is an IEEE standard that defines a test access port (TAP) and boundary scan architecture for digital integrated circuits and provides a standardized serial interface to control the associated test logic. For detailed information on the operation of the JTAG port and TAP controller, see [4]. Figure 42 shows the JTAG timing diagram. Figure 42: JTAG Timing Diagram Table 46 shows the JTAG timing parameters. Table 46: JTAG Timing Parameters Parameter Number Parameter Parameter Name Min Max Unit J1 fTCK Clock Frequency 15 MHz J2 tTCK Clock Period 1/fTCK ns J3 tCL Clock Low Period tTCK/2 ns J4 tCH Clock High Period tTCK/2 ns J7 tTMS_SU TMS Setup Time 1 J8 tTMS_HO TMS Hold Time 16 J9 tTDI_SU TDI Setup Time 1 J10 tTDI_HO TDI Hold Time 16 J11 tTDO_HO TDO Hold Time 15

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 50 of 62 © 2023 Renesas Electronics Table 47 shows the pin definition of the JTAG interface. Table 47: JTAG Pin Configuration Pin Name Pin Number I/O Function Name TMS (Note 3) 7 I/O Data TCLK (Note 4) 8 I Clock GPIOC8 9 I TDI: Data Input GPIOC7 10 O TDO: Data Output GPIOC6 11 I nTRST: Reset SWD protocol can handle the same debug features as the JTAG. Note 3 In case of SWD Debug features, Pin name will be SWDIO, A bidirectional signal. Note 4 In case of SWD Debug features, Pin name will be SWCLK.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 51 of 62 © 2023 Renesas Electronics

8.13 Bluetooth Coexistence

DA16200MOD provides the Bluetooth coexistence function to be properly aligned with external devices activated at 2.4 GHz.

8.13.1 Interface Configuration

The following three pins can be set in pin multiplexing:

  • BT_sig0 (oWlanAct) ○ It indicates that Output, WLAN is currently active
  • BT_sig1 (iBtAct) ○ It indicates that Input, BT/BLE is currently active
  • BT_sig2 (iBTPri) ○ It indicates that Input (Optional), BT/BLE has a higher priority A variety of configurable settings are available, including active high/low, manual force mode, use status of the optional iBTPri function, and whether or not to switch oWlanAct to Active in the event of TX/RX/TRX. oWlanAct iBtAct iBtPri DA16200MOD BT/BLE Figure 43: Bluetooth Coexistence Interface

8.13.2 Operation Scenario

The Bluetooth coexistence can be switched on/off by the configurable register, and the activation scenarios based on the status of each pin are described below:

  • BT_sig0 (oWlanAct) ○ When asserted, external BT/BLE is expected to stop occupying RF
  • BT_sig1 (iBtAct) ○ When asserted, DA16200MOD stops occupying RF
  • BT_sig2 (iBTPri) ○ It is optional and thus may not be used ○ If it is used and DA16200’s iBtAct = Active while iBTPri = Non-Active, DA16200 may ignore iBtAct

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 52 of 62 © 2023 Renesas Electronics

9 Applications Schematic

14 15 16 17 18 19 20 21 22 23 GND RTC_SENSOR RTC_WAKE_UP2 UART0_RXD UART0_TXD NC JTAG_TMS JTAG_TCLK GPIOC8 GPIOC7 GPIOC6 RTC_WAKE_UP RTC_PWR_KEY F_CS VDD_DIO2 F_IO1 F_IO0 F_IO2 F_IO3 F_CLK GPIOA10 GPIOA11 GPIOA9 GPIOA6 GPIOA5 GPIOA4 GPIOA3 GPIOA2 GPIOA1 GPIOA0 VDD_DIO1 VBAT_3V3 NC NC GPIOA7 GPIOA8 DA16200MOD NC

2 VBAT_3V3

VDD_DIO1, (1.8V or 3.3V) VDD_DIO2 4.7KΩ External Wake-up Control 4.7KΩ External Wake_up2 Control 1uF UART interface for debugging JTAG interface 10uF 1uF UART1_TXD UART1_RXD Factory_reset WPS GPIO Interface GPIO Interface GPIO Interface 4.7KΩ 4.7KΩ RTC Sensor Out GPIO Interface (1.8V or 3.3V) If you use it as GPIO function, you don't need full-up resistor If the RTC_WAKE_UP2 function is not uesd, it can be connected to the GND External Power Control *Note: Remove R1 and C1 when MCU controls 'RTC_PWR_KEY' If not controlled by MCU, keep R1 and C1 and connect to VBAT. Test Point Figure 44: Application Schematic Table 48: Component for RTC POWER KEY Quantity Part Reference Value Description

1 R1 470 kΩ

Remove when MCU control ‘RTC_PWR_KEY’. This value should be chosen by customer application to achieve the enough delay time depending on the power-on time of VBAT. For detail information, See 6.1

1 C1 1uF

Remove when MCU control ‘RTC_PWR_KEY’. This value should be chosen by customer application to achieve the enough delay time depending on the power-on time of VBAT. Not to exceed 1uF. For detail information, See 6.1

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 53 of 62 © 2023 Renesas Electronics

10.1 Dimension: DA16200MOD-AAC

Unit: mm Figure 45: AAC Module Dimension

10.2 Dimension: DA16200MOD-AAE

Unit: mm Figure 46: AAE Module Dimension

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 54 of 62 © 2023 Renesas Electronics

10.3 PCB Land Pattern

Unit: mm Figure 47: PCB Land Pattern (Top View) Figure 48: PCB Land Pattern (Bottom View) Ant GND is only needed on the bottom of the PCB. GND must be removed for all layers including the inner layer except the bottom. See Figure 49 for detail.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 55 of 62 © 2023 Renesas Electronics 10.4 4-Layer PCB Example Figure 49: 4-Layer PCB Example

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 56 of 62 © 2023 Renesas Electronics

10.5 Soldering Information

10.5.1 Condition for Reflow Soldering

Figure 50 shows the typical process flow for mounting surface mount packages to PCB. The reflow profile depends on the solder paste being used and the recommendations from the paste manufacture should be followed to determine the proper reflow profile. Figure 51 shows a typical reflow profile when a no-clean paste is used. Oven time above liquidus (260 °C for lead-free solder) is 20 to 40 seconds. The rework process involves the following steps: 1. Component removal 2. Site redress 3. Solder paste application 4. Component placement 5. Component attachment Figure 50: Typical PCB Mounting Process Flow

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 57 of 62 © 2023 Renesas Electronics Table 49: Typical Reflow Profile (Lead Free): J-STD-020C Profile Feature Lead Free SMD Average ramp up rate (Tsmax to Tp) 3 °C/s Max. Preheat

  • Temperature Min (Tsmin)
  • Temperature Max (Tsmax)
  • Time (Tsmax to Tsmin)
  • 150 °C
  • 200 °C
  • 60 to 180 seconds Time maintained above
  • Temperature (TL)
  • Time (tL)
  • 217 °C
  • 60 to 150 seconds Peak/Classification temperature (Tp) 260 °C Time within 5 °C of peak temperature (tp) 20 to 40 seconds Ramp down rate 6 °C/s Max. Time from 25 °C to peak temperature 8 minutes Max. Figure 51: Reflow Condition

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 58 of 62 © 2023 Renesas Electronics The ordering number consists of the part number followed by a suffix indicating the packing method. For details and availability, please visit the Low Power Wi-Fi | Renesas website or contact your local sales representative. Table 50: Ordering Information (Production) Part Number Pins Size (mm) Shipment Form Pack Quantity DA16200MOD-AAC4WA32 37 13.8 x 22.1 x 3.3 Reel MOQ: 500 pcs DA16200MOD-AAE4WA32 37 13.8 x 22.1 x 3.3 Reel MOQ: 500 pcs Part Number Legend: DA16200MOD-AAC4WA32 AA: Module revision number C: Select module type [C] Chip antenna, [E] u.FL connector 4: Flash memory [4] 4Mbyte, [2] 2Mbyte W: Voltage range A3: Package No. 2: T&R packing

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 59 of 62 © 2023 Renesas Electronics

Revision History

3.3 04-Jan-23

  • Section 7.4.1, 8.8.4, Table 17 added details for sleep mode
  • Updated Table 3 to add storage temperature range and adjusted min max voltages 3.2 06-Jun-22
  • Update logo, disclaimer, copyright.
  • Section 4.1 Updated Flash memory Pin-out Description Table 1
  • Section 4.2 Updated Pin Multiplexing Table 2
  • Section 7.3.2 Added note about Sleep Mode 2 &3 for retention I/O
  • Section 0 Fixed typo and added note about SPI slave half-duplex and clock speed calculation
  • Section 8.4 Added SDIO interface needs pull-up resistors description and Figure 18
  • Section 8.5.3 Added I2C Interface Pull-up
  • Section 8.12 Updated SWD part Table 47
  • Section 9 Updated Application Schematic Figure 44 3.1 03-Fab-21
  • Editorial
  • Removed BOR part
  • Added Note for Power on Sequence in the Section 6.1, Updated Figure 7 and Table 16
  • Section 8.7.3 Fixed typo
  • Added Section 8.7.1 and 8.7.2
  • Updated Applications Schematic 3.0 23-Jul-20
  • Sync with SoC datasheet v3.1
  • Modified Chapter 3 description to Network subsystem layer.
  • Modified DA16200MOD pin Mux (Table 2) ○ Added module default pin conditions. ○ I2C CLK GPIOA2 -> GPIOA3
  • Added chapter 5.3.3, 5.3.4
  • Modified Rx max input level in chapter 5.4.1(Table 11)
  • Updated Chapter Note 1 Sleep mode description
  • Updated RTC_PWR_KEY description and remove one sentence which leads to misunderstanding. Table 17
  • Modified I2C timing in Table 30, Table 32
  • Added description of chapter 8.9.1
  • Updated Chapter 9 application schematics
  • Changed Module dimension picture Figure 45 and Figure 46
  • Removed F_xx pins
  • Changed the link from customer support portal to Dialog website.
  • Added PCB land pattern Figure 48, Figure 49

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 60 of 62 © 2023 Renesas Electronics Revision Date Description 2.0 08-May-20

  • Added Tolerance of dimension
  • Added min/max Radio characteristics in Table 11, Table 12and Table 13
  • Modified Chapter 8.10.3 Baud rate
  • Updated Reach and ROHS compliance 0.4 07-Apr-20
  • Updated Key Features
  • Modified DA16200MOD pin Mux Table 2
  • Chapter 7.4 Pulse Counter added
  • Chapter 8.10.1 RS-232 added 0.3 23-Mar-20
  • Added ESD performance, Table 15
  • AC characteristics and current consumption of data updated in Table 11, Table 12 and Table 13
  • Updated Key Features, about clock source & embedded memory 0.2 22-Oct-19 ● Modified module size 0.1 03-Oct-19 ● Preliminary datasheet

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 61 of 62 © 2023 Renesas Electronics Status Definitions Revision Datasheet Status Product Status Definition 1.<n> Target Development This datasheet contains the design specifications for product development. Specifications may be changed in any manner without notice. 2.<n> Preliminary Qualification This datasheet contains the specifications and preliminary characterization data for products in pre-production. Specifications may be changed at any time without notice in order to improve the design. 3.<n> Final Production This datasheet contains the final specifications for products in volume production. The specifications may be changed at any time in order to improve the design, manufacturing and supply. Major specification changes are communicated via Customer Product Notifications. Datasheet changes are communicated via www.renesas.com. 4.<n> Obsolete Archived This datasheet contains the specifications for discontinued products. The information is provided for reference only. Reach and RoHS Compliance Renesas Electronics’s suppliers certify that its products are in compliance with the requirements of REACH and Directive 2015/863/EU of the European Parliament on the restriction of the use of certain hazardous substances in electrical and electronic equipment. RoH S certificates from our suppliers are available on request.

Ultra Low Power Wi-Fi Module Datasheet Revision 3.3 04-Jan-2023 CFR0011-120-00 62 of 62 © 2023 Renesas Electronics Important Notice and Disclaimer RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible fo r (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without no tice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third part y intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Con ditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warra nties or warranty disclaimers for these products. © 2023 Renesas Electronics Corporation Corporate Headquarters TOYOSU FORESIA, 3-2-24 Toyosu Koto-ku, Tokyo 135-0061, Japan www.renesas.com Contact Information For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: https://www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners.