D1U4CS-W-2200-12-HXXC_V01 MURATA-PS | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 6
Technical content
D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply CPS_D1U4CS-W-2200-12-HxxC.A10 Page 1 of 6 www.murata-ps.com www.murata-ps.com/support For full details go to www.murata-ps.com/rohs
FEATURES
2200W (220Vac), 1100W (110Vac) Output Power Certified to Climate Savers Computing InitiativeSM and 80 PLUS® Gold efficiency 12V Main Output, 3.3V or 5V Standby Output 1U height: 4.0" x 14.0" x 1.6" 24.5 Watts per cubic inch density N+1 redundancy capable, including hot plugging (up to 4 in parallel) Active Current Sharing on main output; ORing FET Overvoltage, Overcurrent, Overtemperature protection Internal cooling fans (variable speed) I²C Bus Interface, PSMI compliant RoHS compliant Optional 1U x 19" Power-Shelf ORDERING GUIDE Model Number Power Output High Line AC Power Output Low Line AC Main Output Standby Output Airflow D1U4CS-W-2200-12-HC4C 2200W 1100W 12.12V 3.3V Back to front D1U4CS-W-2200-12-HC3C 2200W 1100W 12.12V 3.3V Front to back D1U4CS-W-2200-12-HA4C 2200W 1100W 12.12V 5V Back to front D1U4CS-W-2200-12-HA3C 2200W 1100W 12.12V 5V Front to back INPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Input Voltage Operating Range 90 115/230 264 Vac Input Frequency 47 60 63 Hz Turn-on Input Voltage Ramp up 81 89 VacTurn-off Input Voltage Ramp down 70.5 78 Maximum Input Current Low Line AC 90Vac 13 ArmsHigh Line AC 180Vac 13 Inrush Current Cold start between 0-1msec 16.5 Apk Power Factor Output load >90% 0.95 Output load >50% 0.95 OUTPUT VOLTAGE CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units 12V Voltage Set Point Accuracy 12.12 VdcLine and Load Regulation 11.76 12.48 Ripple Voltage & Noise1 20MHz Bandwidth 120 mV p-p Output Current 9 180 A Load Capacitance 30000 µF 5Vsb Voltage Set Point Accuracy 5 VdcLine and Load Regulation 20MHz Bandwidth 4.85 5.15 Ripple Voltage & Noise1 50 mV p-p Operating Range 0 5 A Load Capacitance 10000 µF 3.3Vsb Voltage Set Point Accuracy 3.3 VdcLine and Load Regulation 20MHz Bandwidth 3.2 3.4 Ripple Voltage & Noise1 50 mV p-p Operating Range 0 6 A Load Capacitance 10000 µF 1 Ripple and noise are measured with 0.1 uF of ceramic capacitance and 10 uF of tantalum capacitance on each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used. PRODUCT OVERVIEW The D1U4CS-W-2200-12-HxxC is a 2200 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping redundant systems. The main output is 12V with a standby output of 5V or 3.3V. Packaged in a 1U low profile enclosure, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power archi- tecture systems requiring high power density. The highly efficient electrical and thermal design with internal cooling fans supports reliable operation conditions. The D1U4CS-W-2200-12-HxxC is designed to autorecover from overtemperature fault. Status information is provided with front panel LEDs, logic signals and an I 2C management interface. Four units can be packaged into an optional 19" 1U power shelf to provide up to 8.8kW of power. CB Test Certificate and Test Report * To Be Discontinued * To Be Discontinued * To Be Discontinued * To Be Discontinued * To Be Discontinued * Last time buy date is 3/31/2022.
D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply CPS_D1U4CS-W-2200-12-HxxC.A10 Page 2 of 6 www.murata-ps.com/support OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Remote Sense 120 mV Efficiency (230V) excluding fan load 20% load 88 89.1 %50% load 92 93.0 100% load 88 92.2 Output Rise Monotonicity Overshoot less than 10% for all outputs, no voltage negative between 10% to 95% during ramp up Startup Time AC ramp up 1.5 s PS_On activated 150 ms Transient Response 12V Ramp 1A/μs ±360 mV5Vsb Ramp 1A/μs ±150 3.3Vsb Ramp 1A/μs ±100 Current sharing accuracy (up to 4 in parallel) At 100% load ±7 % Hot Swap Transients All outputs remain in regulation 5 % Holdup Time 100% load 12 ms ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range Non-condensing -40 70 °COperating Temperature Range D1U4CS-W-2200-12-HC4C and D1U4CS- W-2200-12-HA4C models 0 50 D1U4CS-W-2200-12-HC3C and D1U4CS- W-2200-12-HA3C models 0 40 Operating Humidity Non-condensing 10 90 %Storage Humidity 5 90 Shock 30G non operating Sinusoidal Vibration 0.5G, 5 – 500 Hz operating MTBF Calculated per Bellcore at Ta=30°C 400K hrs Demonstrated 400K hrs Acoustic ISO 7779-1999 60 dB LpAm Safety Approvals CAN/CSA C22.2 No 60950-1-07, Am.1:2011 UL 60950-1-2011, 2nd Ed. UL 60950-1, 2nd Ed. IEC60950-1:2005 (2nd Ed.) w A1:2009, EN 60950-1:2006+A11:2009 +A1:2010 +A12:2011 Input Fuse Power Supply has internal 20A/250V fast blow fuse on the AC line input Material Flammability UL 94V-0 Switching Frequency TBD Weight 4.5lbs (2.1kg) PROTECTION CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units Overtemperature Autorestart 55 65 °C 12V Overvoltage Latching 13.1 14.1 V Overcurrent Latching 197 225 A 5Vsb Overvoltage Latching 5.6 6.2 V Overcurrent Brick wall, autorecovery 5.5 6.2 A 3.3Vsb Overvoltage Latching 3.5 4.0 V Overcurrent Brick wall, autorecovery 6.5 8.0 A
D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply CPS_D1U4CS-W-2200-12-HxxC.A10 Page 3 of 6 www.murata-ps.com/support ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Insulation Safety Rating / Test Voltage Input to Output - Reinforced 3000 Vrms Input to Chassis - Basic 1500 Vrms Isolation Output to Chassis Output to Output Grounding Main Output Return and Standby Output Return are connected internally. 100kΩ resistor parallel with 100nF capacitor is connected between Return and power supply chassis. Main Output Return should be connected to the System Chassis STATUS INDICATORS AND CONTROL SIGNALS Status Conditions Description LEDs Off No AC to all Power Supply Flashing Green Main Output Absent Flashing Amber Calibration Mode; not a normal operating condition Solid Amber PW Fail or PWOK Low. Note: The LED will also show Solid Amber if the power module is: 1. Not correctly installed within its slot (in the host system shelf) with PS_KILL (Pin B5) correctly terminated. 2. Operated externally (as a standalone power module) and is not connected to an Output Connector Card ACAN-32 (see Optional Accessories) that correctly terminates PS_KILL (Pin B5). Solid Green Power Supply Good I2C Registers Refer to Application Note #ACAN-33 EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics IEC/EN 61000-3-2 Complies Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Complies Conducted Emissions FCC 47 CFR Part 15/CISPR 22/EN55022 Class A, 6dB margin Radiated Emissions FCC 47 CFR Part 15/CISPR 22/EN55022 Class A, 6dB margin ESD Immunity IEC/EN 61000-4-2 4kV contact discharge 8kV operational air discharge 15kV non-operational air discharge Radiated Field Immunity IEC/EN 61000-4-3 Complies Electrical Fast Transients/Burst Immunity IEC/EN 61000-4-4 Complies Surge Immunity IEC/EN 61000-4-5 1kV/2kV, Performance Criteria A RF Conducted Immunity IEC/EN 61000-4-6 3 Vac, 80% AM, 1kHz, Performance Criteria A Magnetic Field Immunity IEC/EN 61000-4-8 3 A/m Voltage dips, interruptions IEC/EN 61000-4-11 Complies
D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply CPS_D1U4CS-W-2200-12-HxxC.A10 Page 4 of 6 www.murata-ps.com/support OUTPUT CONNECTOR AND SIGNAL SPECIFICATION DC and Signal Connector: FCI PowerBlade # 51732-048LF Pin Assignment Signal Name Description High Level Low Level I Max P1 to P5 VOUT Main output voltage P6 to P10 VRTN Main output voltage, return A1 Sense + VOUT remote sense, positive node input, connected to the +ve load point A2 Sense - VOUT remote sense, negative node input, connected to the -ve load point C5, C6, D5, D6 Vsb Standby voltage output C3, C4, D3, D4 Vsb Return Standby voltage, return, tied internally to Output Return B1 I_Share Active load sharing bus 0 – 8V -4 mA / +5 mA D1 AC_OK/H Input AC Voltage “OK” signal output (Internal pull up is 10kΩ to Vsb) >2.1V <0.8V +4 mA -2 mA D2 PW_OK/H Internal pull up of 10KΩ to Vsb >2.1V <0.8V +4 mA -2 mA C2 SMB/Alert SMB/Alert signal output (open collector) B5 PS_Kill Floating pin will turn off P/S (shorter pin, last-make and first- break contact for hot plugging). This signal overrides PS-On in disabling the Main Output >2.1V (open) <0.8V (active, PS:On) N/A B6 PS_Present Internally tied to Vsb Return 0 V A6 PS_On/L Internal 3.3KΩ pull-up to Vsb (accepts open collector/ drain drive). This signal to be pulled low to turn-on power supply >2.1V (open, or 3.3V) <0.8V (active, PS:On) A3 I2C Data I2C serial data bus; internal 4.64KΩ pull-up to Vsb A4 I2C Clock I2C serial clock bus; internal 4.64KΩ pull-up to Vsb B2 I2C Adr0 Address input 0, internal 10KΩ pull-up to Vsb >2.1V <0.8V ±1 mA B3 I2C Adr1 Address input 1, internal 10KΩ pull-up to Vsb >2.1V <0.8V ±1 mA B4 I2C Adr2 Address input 2, internal 10KΩ pull-up to Vsb >2.1V <0.8V ±1 mA D1U4CS MATING CONNECTORS 12V D1U4 mating connector Press Fit Solder 1 Straight Right Angle Straight Right Angle Murata-PS N/A 4321-01454-0 N/A N/A FCI 51742-11002400AALF 51762-11002400ABLF N/A N/A 1 Solder connector recommended for board thickness of <0.090 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 x1 x2 x3 x4 x5 x6 VOUT VOUT VOUT VOUT VOUT VRTN VRTN VRTN VRTN VRTN AC_OK/H PW_OK/H Vsb RETURN Vsb RETURN Vsb +OUT Vsb +OUT D SPARE SMB/Alert Vsb RETURN Vsb RETURN Vsb +OUT Vsb +OUT C I_SHARE I2C ADR0 I2C ADR1 I2C ADR2 PS_KILL PS_PRE- SENT B SENSE + SENSE - I2C DATA I2C CLOCK SPARE PS_ON/L A mate-last pins
D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply CPS_D1U4CS-W-2200-12-HxxC.A10 Page 5 of 6 www.murata-ps.com/support WIRING DIAGRAM FOR OUTPUT CURRENT SHARING NOTES 12V Output: Current sharing is achieved using the active current share method. (See wiring diagram for connection details.) The total combined load must be below 2200W at startup. Current sharing can be achieved with or without remote sense connected to the common load. VSB outputs can be tied together for redundancy but total combined output power must not exceed 25W. The VSB output has internal ORing MOSFET for additional redundancy / internal short protection. The current share pin B1 is a connection between the two units. It is input and/or output as the voltage on the line controls the current share. A power supply will respond to a change in this voltage but a power supply can also change the voltage depending on the load drawn from it. On a single unit this would read 8V at 100% load. For two units sharing load then this should read 4V for perfect current sharing. Up to 6 units can be paralleled together. Please consult your Murata sales representative if operation with more than six units in parallel is needed. VRTN Sense + (Main Output Remote Sense) Sense – VOUTA1 Dotted lines show optional remote sense connections. Optional remote sense lines can be attached to a load that is a distance away from the power supply to improve regulation at the load. D1U4CS 12V load C3,C4,D3,D4 C5,C6,D5,D6 Close switch (or FET, BJT, or wire) to turn on +12V OUT Vsb logic circuitry Vsb PS_On Vsb Return B5 PS_Kill D1U4CS B1 I_Share PS_Kill B5 C3,C4,D3,D4Vsb Return PS_On A6 Vsb A2Sense – I_Share VRTN VOUT Sense + (Main Output Remote Sense) P6-P10 P1-P5P1-P5 P6-P10 C5,C6,D5,D6
D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply CPS_D1U4CS-W-2200-12-HxxC.A10 Page 6 of 6 www.murata-ps.com/support Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2021 Murata Power Solutions, Inc. Murata Power Solutions, Inc. 129 Flanders Rd. Westborough, Ma 01581, USA. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: https://www.murata-ps.com/requirements/ MECHANICAL DIMENSIONS - D1U4CS-W-2200-12-HxxC OPTIONAL ACCESSORIES Description Part Number 12V D1U4CS-12 output connector card D1U4CS-12-CONC APPLICATION NOTES Document Number Description Link ACAN-32 D1U4CS-12-CONC Output Connector Card www.murata-ps.com/data/apnotes/acan-32.pdf ACAN-33 D1U4CS-W Communication Protocol www.murata-ps.com/data/apnotes/acan-33.pdf ACAN-37 D1U4CS-x EEPROM Specification www.murata-ps.com/data/apnotes/acan-37.pdf AC Input Connector: The AC input connector is standard IEC C20 20A. Airflow Front to Back Airflow Back to Front 2.40 ±0.25 0.094 ±0.010 349.60 ±0.40 13.764 ±0.016 355.60 ±0.65 14.000 ±0.026 8.89 ±0.25 0.350 ±0.010 41.00 ±0.40 1.614 ±0.016 12.63 ±0.40 0.497 ±0.016 7.62 ±0.40 0.300 ±0.016 101.60 ±0.50 4.000 ±0.020 13.25 ±0.30 0.522 ±0.012 10.75 ±0.30 0.423 ±0.012 BARCODE muRata Ps