D1U4CS-W-2200-12-HA3C

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 1 of 5 email: toronto@murata-ps.com For full details go to www.murata-ps.com/rohs Ḥ www.murata-ps.com

FEATURES

2200W (220Vac), 1100W (110Vac) Output Power Certifi ed to Climate Savers Computing InitiativeSM and 80 PLUS® Gold effi ciency 12V Main Output, 3.3V or 5V Standby Output 1U sized; dimensions 14.0” x 4.0” x 1.6” 24.5 Watts per cubic inch density N+1 redundancy capable, including hot-docking Active Current Sharing on main output Over-voltage, Over-current, Over-temperature protection Internal cooling fans (variable speed) I²C Bus Interface, PSMI compliant RoHS compliant Optional 1U x 19” Power-Shelf SELECTION GUIDE Model Number Power Output High Line AC Power Output Low Line AC Main Output Standby Output Airfl ow D1U4CS-W-2200-12-HC4C 2200W 1100W 12.12V 3.3V Back to front D1U4CS-W-2200-12-HC3C 2200W 1100W 12.12V 3.3V Front to back D1U4CS-W-2200-12-HA4C 2200W 1100W 12.12V 5V Back to front D1U4CS-W-2200-12-HA3C 2200W 1100W 12.12V 5V Front to back INPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Input Voltage Operating Range Low Line AC 90 140 VacHigh Line AC 180 264 Input Frequency 47 60 63 Hz Turn-on Input Voltage Ramp up 81 89 VacTurn-off Input Voltage Ramp down 70.5 78 Maximum Input Current Low Line AC 90Vac 13 ArmsHigh Line AC 180Vac 13 Inrush Current Cold start between 0-1msec 16.5 Apk Power Factor Output load >90% 0.95 Output load >50% 0.95 OUTPUT VOLTAGE CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units 12V Voltage Set Point Accuracy 12.12 VdcLine and Load Regulation 11.76 12.48 Ripple Voltage & Noise 20MHz Bandwidth 120 mV p-p Output Current 0 180 A Load Capacitance 30000 μF 5Vsb Voltage Set Point Accuracy 5 VdcLine and Load Regulation 20MHz Bandwidth 4.85 5.15 Ripple Voltage & Noise 50 mV p-p Operating Range 0 5 A Load Capacitance 10000 μF 3.3Vsb Voltage Set Point Accuracy 3.3 VdcLine and Load Regulation 20MHz Bandwidth 3.2 3.4 Ripple Voltage & Noise 50 mV p-p Operating Range 0 6 A Load Capacitance 10000 μF 1 Ripple and noise are measured with 0.1 uF of ceramic capacitance and 10 uF of tantalum capacitance on each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used. PRODUCT OVERVIEW The D1U4CS-W-2200-12-HxxC is a 2200 Watt, power-factor-corrected (PFC) front-end power supply for hot- swapping redundant systems. The main output is 12V with standby output of 5V or 3.3V. Packaged in 1U low profi le, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power architecture systems requiring high power density. The highly effi cient electrical and thermal design with internal cooling fans supports reliable operation conditions. The D1U4CS-W-2200-12-HxxC is designed to auto-recover from overtemperature fault. Status information is provided with front panel LEDs, logic signals and I 2C management inter- face. Four units can be packaged into an optional 19” 1U power shelf to provide up to 8.8kW of power.

D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 2 of 5 email: toronto@murata-ps.comwww.murata-ps.com OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Remote Sense 120 mV Effi ciency (80+ measurement; excludes fan load) 20% and full load 89.10 %50% load 93.04 Output Rise Monotonicity Overshoot less than 10% for all outputs, no voltage negative between 10% to 95% during ramp up Start-up Time AC ramp up 1.5 s PS_On activated 150 ms Transient Response 12V Ramp 1A/μs ±360 mV5Vsb Ramp 1A/μs ±150 3.3Vsb Ramp 1A/μs ±100 Current sharing accuracy (up to 3 in parallel) At 100% load ±7 % Hot Swap Transients All outputs within regulation 5 % Hold-up Time 100% load 12 ms GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range Non-condensing -40 70 °COperating Temperature Range D1U4CS-W-2200-12-HC4C and D1U4CS-W-2200-12-HA4C models only 05 0 D1U4CS-W-2200-12-HC3C and D1U4CS-W-2200-12-HA3C models only 04 0 Operating Humidity Non-condensing 10 90 %Storage Humidity 59 0 Shock 30G non operating Sinusoidal Vibration 0.5G, 5 – 500 Hz operating MTBF Calculated per Bellcore at Ta=30°C 400 Khrs Demonstrated 400 Khrs Acoustic ISO 7779-1999 60 dB LpAm Safety Approvals c-CSA-us (CSA 60950-1-03/UL 60950-1, Second Edition) Input Fuse Power Supply has internal 20A/250V fast blow fuse on the AC line input Material Flammability UL 94V-0 Switching Frequency TBD Weight 2.1kg PROTECTION CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units Over-temperature Auto-restart 55 65 °C 12V Over Voltage Latching 13.12 14.12 V Over Current Latching 197 225 A 5Vsb Over Voltage Latching 5.6 6.26 V Over Current Brick wall, autorecovery 5.5 6.25 A 3.3Vsb Over Voltage Latching 3.57 4.02 V Over Current Brick wall, autorecovery 6.5 8.0 A

D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 3 of 5 email: toronto@murata-ps.comwww.murata-ps.com ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Insulation Safety Rating / Test Voltage Input to Output - Reinforced 3000 Vrms Input to Chassis - Basic 1500 Vrms Isolation Output to Chassis Output to Output Material Flammability UL 94V-0 Grounding Main Output Return and Standby Output Return are connected internally. 100kΩ resistor parallel with 100nF capacitor is connected between Return and power supply chassis. Main Output Return should be connected to the System Chassis CONTROL SIGNALS Status Conditions Description LED Off No AC input to all PS Flashing Green Main Output Absent Green Power Supply Good I2C Registers Refer to Application Note #ACAN-33 EMISSIONS AND IMMUNITY Characteristic Description Criteria Harmonics IEC/EN 61000-3-2 Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Emission Conducted FCC 47 CFR Parts 15/CISPR 22/EN55022 Class A, 6dB margin Emission Radiated FCC 47 CFR Parts 15/CISPR 22/EN55022 Class A, 6dB margin ESD IEC/EN 61000-4-2 4kV contact discharge 8kV operational air discharge 15kV non-operational air discharge Electromagnetic Field IEC/EN 61000-4-3 Electrical Fast Transients/Burst IEC/EN 61000-4-4 Surge IEC/EN 61000-4-5 1kV/2kV, Performance Criteria A RF Conducted Immunity IEC/EN 61000-4-6 3 Vac, 80% AM, 1kHz, Performance Criteria A Magnetic Immunity IEC/EN 61000-4-8 3 A/m Voltage dips, interruptions IEC/EN 61000-4-11

D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 4 of 5 email: toronto@murata-ps.comwww.murata-ps.com OUTPUT CONNECTOR AND SIGNAL SPECIFICATION DC and Signal Connector: FCI PowerBlade # 51732-048LF Pin Assignment Signal Name Description High Level Low Level I Max P1 to P5 VOUT Main output voltage P6 to P10 VRTN Main output voltage, return A1 Sense + VOUT remote sense, positive node input, connected to the +ve load point A2 Sense - VOUT remote sense, negative node input, connected to the -ve load point C5, C6, D5, D6 Vsb Standby voltage output C3, C4, D3, D4 Vsb Return Standby voltage, return, tied internally to Output Return B1 I_Share Active load sharing bus 0 – 8V -4 mA / +5 mA D1 AC_OK/H Input AC Voltage “OK” signal output (Internal pull up is 10kΩ to 3.3V) >2.1V <0.8V +4 mA -2 mA D2 PW_OK/H Internal pull up of 10K ohm to 3.3V >2.1V <0.8V +4 mA -2 mA C2 SMB/Alert SMB/Alert signal output (open collector) B5 PS_Kill Floating pin will turn off P/S (shorter pin, last-make and fi rst-break contact for hot plugging). This signal overrides PS-On in disabling the Main Output >2.1V (open) <0.8V (active, PS:On) N/A B6 PS_Present Internally tied to 3.3V return 0 V A6 PS_On/L Internal 3.3K ohm pull-up to 3.3V, (accepts open collector/ drain drive), This signal to be pulled low to turn-on power supply >2.1V (open, or 3.3V) <0.8V (active, PS:On) A3 I 2C Data I 2C serial data bus; internal 4.64K ohm pull-up 3.3V A4 I 2C Clock I 2C serial clock bus; internal 4.64K ohm pull-up 3.3V B2 I 2C Adr0 Address input 0, internal 10K ohm pull-up to 3.3V >2.1V <0.8V ±1 mA B3 I 2C Adr1 Address input 1, internal 10K ohm pull-up to 3.3V >2.1V <0.8V ±1 mA B4 I 2C Adr2 Address input 2, internal 10K ohm pull-up to 3.3V >2.1V <0.8V ±1 mA D1U4CS MATING CONNECTORS 12V D1U4 mating connector Press Fit Solder 1 Straight Right Angle Straight Right Angle Murata-PS N/A 4321-01454-0 N/A N/A FCI N/A 51762-11002400ABLF N/A N/A 1 Solder connector recommended for board thickness of <0.090 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 x1 x2 x3 x4 x5 x6 VOUT VOUT VOUT VOUT VOUT VRTN VRTN VRTN VRTN VRTN AC_OK/H PW_OK/H Vsb RETURN Vsb RETURN Vsb +OUT Vsb +OUT D SPARE SMB/ Alert Vsb RETURN Vsb RETURN Vsb +OUT Vsb +OUT C I_SHARE I 2C ADR0 I 2C ADR1 I 2C ADR2 PS_KILL PS_ PRESENT B SENSE + SENSE - I 2C DATA I2C CLOCK SPARE PS_ON/L A mate-last pins

D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply 17 Aug 2010 CPS_D1U4CS-2200-12-HxxC.A04 Page 5 of 5 email: toronto@murata-ps.com Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi cations are subject to change without notice. © 2010 Murata Power Solutions, Inc. Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfi eld, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED www.murata-ps.com/locations MECHANICAL DIMENSIONS - D1U4CS-W-2200-12-HxxC OPTIONAL ACCESSORIES Description Part Number 12V D1U4CS output connector card D1U4CS-12-CONC APPLICATION NOTES Document Number Description ACAN-32 Output Connector Card for D1U4CS ACAN-33 D1U4CS Communication Protocol Dimensions: 13.76”L x 4.00” W x 1.61” H AC Input Connector: The AC input connector is standard IEC C20 20A. 2.40 ±0.25 0.094 ±0.010 349.60 ±0.40 13.764 ±0.016 355.60 ±0.65 14.000 ±0.026 8.89 ±0.25 0.350 ±0.010 41.00 ±0.40 1.614 ±0.016 12.63 ±0.40 0.497 ±0.016 7.62 ±0.40 0.300 ±0.016 101.60 ±0.50 4.000 ±0.020 Airfl ow Front to Back Airfl ow Back to Front