D1U4CS-D-2100-54-HA3DC

D1U4CS-D-2100-5X-HA3DC MURATA-PS | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 5

Technical content

DC-DC Front End Power Supply CPS_D1U4CS-D-2100-5x-HA3DC.A04 Page 1 of 5 www.murata-ps.com www.murata-ps.com/support For full details go to www.murata-ps.com/rohs

FEATURES

 2100W output power  93% effi cient at half power  Floating 54V main output and 5V standby output  1U height: 4"x13.5"x1.6"  24.3 Watts per cubic inch density  N+1 redundancy capable, including hot-swa pping  Droop current sharing  Overvoltage, overcurrent, overtemperature protection Internal cooling fans PMBus™ / I²C interface with status indicators  RoHS compliant PRODUCT OVERVIEW This highly effi cient, 2100W, 54V (or 52.5V) output DC-DC converter is designed to deliver reliable bulk power to 54V distributed power systems, making it ideal for telecom and other high power density applications. The power supplies are N+1 redundant, hot-swappable, and have internal cooling fans. The power supply automatically recovers from overcurrent and overtemperature faults, and status information is provided through front panel LEDs, logic signals and its PMBus ™ / I2C interface. ORDERING GUIDE Part Number Output Power Main Output Standby Aux Output Airfl ow Current Share D1U4CS-D-2100-54-HA3DC 2100W 54V 5V Front to back Droop D1U4CS-D-2100-52-HA3DC 2040W 52.5V 5V Front to back Droop INPUT CHARACTERISTICS Parameter Conditions Min. Nom. Max. Units Input Voltage Operating Range -40 -72 VdcTurn-on Input Voltage Ramp up -43 -44 Turn-off Input Voltage Ramp down -38.5 -39.5 Maximum Current at Vin = -40V 2100W 59 A DC Line Inrush Peak Current 90 Apk I2C reading accuracy Input Power and Output Power 25% load 5 50% load 4 100% load 2.5 Effi ciency (40Vdc - 72Vdc) 20% load 90 50% load 93 100% load 91 OUTPUT VOLTAGE CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units 54V model Voltage Set Point Accuracy 50% load 53.87 54 54.14 VdcLine & Load Regulation 51.98 56.06 Main output, all models Droop 0.075 V/Amp Ripple Voltage & Noise1 20MHz Bandwidth 500 mVp-p Output Current 0 40 A Load Capacitance 0 6800 uF 5Vaux2 Voltage Set Point Accuracy 50% load 4.95 5 5.05 VdcLine & Load Regulation 4.808 5.196 Droop 0.25 V/Amp Ripple Voltage & Noise1 20MHz Bandwidth 50 mVp-p Output Current 0.75 A 1 Ripple and noise are measured with 0.1 uF of ceramic capacitance and 10 uF electrolytic capacitance on each of the power supply outputs. 2 5Vaux is referenced to logic ground. CB Test Certifi cate and Test Report To Be Discontinued* *LAST TIME BUY: 10/1/2018. CLICK HERE FOR DISCONTINUANCE NOTICES.

DC-DC Front End Power Supply CPS_D1U4CS-D-2100-5x-HA3DC.A04 Page 2 of 5 www.murata-ps.com/support OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Output Rise Monotonicity Monotonic with no overshoot Startup Time DC input applied 1 3 s PS_On activated 150 300 ms Transient Response Main Output Ramp, 1A/μs 50% load step 2000 mV5Vaux Ramp, 1A/μs 50% load step ±200 Current sharing accuracy (up to 8 in parallel) At 100% load ±10 % Holdup Time 50% load 8 ms ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range -40 85 °COperating Temperature Range -5 55 Operating Humidity Non-condensing 5 90 %Storage Humidity Non-condensing 5 95 Altitude (without derating at 40°C) 4000 mAltitude (without derating at 55°C) 1800 Shock IEC 60068-2-27 Sinusoidal Vibration IEC 60068-2-64 MTBF Telcordia SR-332 M1C1 @40°C 439K Hours Demonstrated 90% confi dence 300K Hours Acoustic 60 dB LpAm Safety Approvals IEC60950-1:2006/A11:2009 EN60690-1:2006+A11:2009 (Evaluated) CE Marking per LVD Input Fuse Power Supply has internal 80A/170VDC slow blow fuse on 48V input Switching Frequency 160KHz for Main Output Converter 200KHz for Standby Output Converter Weight 4.1lbs (1.86kg) PROTECTION CHARACTERISTICS Output Voltage Parameter Conditions Min. Typ. Max. Units Overtemperature (intake) (54V model only) Autorestart 57 60 63 °C Main Output Overvoltage Latching 57 60 V Overcurrent Autorestart 44 48 A 5Vaux Overvoltage Latching 6.0 6.5 V Overcurrent Autorestart 0.82 1.65 A ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Insulation Safety Rating / Test Voltage Input to Output 1414 Vdc Input to Chassis - Basic 1414 Vdc Isolation Floating outputs to Chassis 707 Vdc

DC-DC Front End Power Supply CPS_D1U4CS-D-2100-5x-HA3DC.A04 Page 3 of 5 www.murata-ps.com/support STATUS INDICATOR AND CONTROL SIGNALS Status Conditions Description Input OK LED Green DC input present and within range Blinking at 1Hz DC input present and outside range Off DC input not present Output OK LED Green Outputs are present and within regulation Blinking at 1Hz Power limit or overcurrent condition Fault LED Red Fault condition present Off No fault condition detected See also ACAN36 for additional LED operation details. FAN MONITORING Status Conditions Description Fan monitoring is available through the I2C interface Both fans running normally PMBus CMD E5 Byte 2 bit 3 One fan failed (or rotor locked) PMBus CMD E5 Byte 2 bit 3 Both fans failed (or rotors locked) PMBus CMD E5 Byte 2 bit 3 EMISSIONS AND IMMUNITY Characteristic Standard Compliance Conducted Emissions FCC 47 CFR Part 15/CISPR 22/EN55022 Class A, 6dB margin Radiated Emissions FCC 47 CFR Part 15/CISPR 22/EN55022 Class A, 6dB margin ESD Immunity IEC/EN 61000-4-2 8kV contact discharge 15kV operational air discharge Radiated Field Immunity IEC/EN 61000-4-3 10 V/m, Performance Criteria A Electrical Fast Transients/Burst Immunity IEC/EN 61000-4-4 2kV, Performance Criteria A Surge Immunity IEC/EN 61000-4-5 1kV/1kV, Performance Criteria A RF Conducted Immunity IEC/EN 61000-4-6 10Vrms, 80% AM, 1kHz, Performance Criteria A Magnetic Field Immunity IEC/EN 61000-4-8 30 A/m Ring Wave IEC/EN 61000-4-12 1kV, Performance Criteria A

DC-DC Front End Power Supply CPS_D1U4CS-D-2100-5x-HA3DC.A04 Page 4 of 5 www.murata-ps.com/support OUTPUT CONNECTOR AND SIGNAL SPECIFICATION DC and Signal Connector: Pin Assignment Signal Name Description High Level Low Level Comments P1,P2, P3 -48VDC Input (-) P4, P5, P6 -48VDC_RTN Input (+) P7 Frame GND Frame ground P8, P9 54V 3 Main Output Voltage (+) P10, P11 54VDC_RTN 3 Main Output Voltage Return (-) A3 +5V-AUX Auxiliary Output A2 PS_Fault Output Voltage within specifi cation 4 >2.4V, OK -50mA, open drain B4 PS_Present B4 is tied to logic ground inside the power supply 0V B2 OUT_ENABLE_L Enable Main Output (internal 10K pull-up to +5Vdc) 5 >3.4V, disabled <1.2V, enabled Min 0.6V hysteresis B6, B5 I2C-SDA_0, I2C-SDA_1 I2C serial data bus +5Vdc D6, D5 I2C-SCL_0, I2C-SCL_1 I2C serial clock bus +5Vdc D1 I2C Reset I2C reset B3 ADD0 Address Input 0, internal Pull-up to Vdd (+5Vdc) >2.1V, <0.8V C3 ADD1 Address Input 1, internal Pull-up to Vdd (+5Vdc) >2.1V, <0.8V D3 ADD2 Address Input 2, internal Pull-up to Vdd (+5Vdc) >2.1V, <0.8V A1, B1, C1, C4 Reserved Reserved A4, A5, A6, C5, C6, D4 Logic Gnd Connected to Logic Gnd 3 Output voltage setpoint is 52.5V on the D1U4CS-D-2100-52-HA3DC model 4 See also ACAN36 for additional details on fault conditions. PS_Fault remains high when OUT_ENABLE_L is disabled and output is off. 5 Pull OUT_ENABLE_L (pin B2) to Logic Gnd (pin A4, A5, A6, C5, C6, D4) to enable main output. Do not exceed 5.5V on OUT_ENABLE_L pin. D1U MATING CONNECTORS Power Supply Mating Connector Straight Right Angle Tyco 6450842-2 TBD 6450882-2 FCI 10106263-B006001LF TBD 10106265-B006002C Note: Connector is viewed from the rear of the PSM Last-to-make, fi rst-to-break shortest pin First to make, last to break longest pin must be implemented in mating connector DC Input: 72Vdc max. DC Output: 54V or 52.5V P 1 P 2 P 3 P 4 P 5 P 6 P 7 P 8 P 9 P 1 0 P 1 1 1 2 3456 -I2C Reset -Interrupt Address Logic GND SCL_1 SCL_0 D Vin Vin Vin Vin Vin Vin FRAME Vout Vout Vout Vout Reserved -Interrupt Address

1 Reserved Logic

-48V -48V -48V -48V Rtn -48V Rtn -48V Rtn GND 54V 3 54V3 54V Rtn3 54V Rtn3 Reserved -Output Enable Address -PS Present SDA_1 SDA_0 B Reserved -PS Fault +5Vaux Logic GND Logic GND Logic GND A

DC-DC Front End Power Supply CPS_D1U4CS-D-2100-5x-HA3DC.A04 Page 5 of 5 www.murata-ps.com/support Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifi cations are subject to change without notice. © 2012 Murata Power Solutions, Inc. Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfi eld, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ MECHANICAL DIMENSIONS OPTIONAL ACCESSORIES Description Part Number 54V D1U-54D output connector card D1U4CS-54D-CONC APPLICATION NOTES Document Number Description Link ACAN-35 D1U4CS-54D Output Connector Card www.murata-ps.com/data/apnotes/acan-35.pdf ACAN-36 D1U4CS-D-2100-xx-HA3xC Communication Protocol www.murata-ps.com/data/apnotes/acan-36.pdf ACAN-37 D1U4CS-x EEPROM Specifi cation www.murata-ps.com/data/apnotes/acan-37.pdf 51.64 ±0.35 101.60 ±0.50 27.71 ±0.35 3.00 ±0.10 26.67 ±0.25 344.47 ±0.50 20.96 ±0.25 40.64 ±0.40 2X 1.52 2.44 4.00 23.62 329.01 ±0.52 4.93 ±0.35 3.00 ±0.10 26.67 ±0.25 6.30 ±0.25 86.11 10.92 5.46 ±0.25 50.80 ±0.35 23.95 ±0.35 13.49 ±0.25 Airflow Front to Back