CTG201003ULM AAC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
American Accurate Components, Inc. THIN FILM PRECISION CHIP RESISTORS The content of this specification may change without notification 10/12/07
188 Technology Drive, Unit H, Irvine, CA 92618
TEL: 949-453-9888 FAX: 949-453-8889 Custom solutions are available. CT Series Chip Resistors – Tin / Gold Terminations Available SCHEMATIC DIMENSIONS (mm) Size L W c d t 0402 1.00 + 0.05 0.5+0.1 -0.05 -0.10 0.35 + 0.05 -0.10 0.50 + 0.10 -0.10 0.50 + 0.15 -0.10 0.60 + 0.15 -0.10 0.60 + 0.10 -0.10 0.70 + 0.10 Wraparound Termination Top Side Termination, Bottom Isolated – CTG Type CONSTRUCTION FIGURE (Wraparound) CONSTRUCTION MATERIALS Item Part Material n Resistor Nichrome Thin Film o Protective Film Polymide Epoxy Resin p Electrode pa Grounding Layer Nichrome Thin Film pb Electrode Layer Copper Thin Film pc Barrier Layer Nickel Plating pd Solder Layer Solder Plating (Sn) q Substrate Alumina Marking Epoxy Resin r & s The resistance value is on the front side The production month is on the backside HOW TO ORDER CT G 10 1003 B X M Packaging M = Std. Reel O = 1K Reel TCR (PPM/°C) L = + 1 P = + 5 Y = + 50 M = + 2 Q = + 10 Z = + 100 N = + 3 X = + 25 Tolerance (%) EIA Resistance Value Standard decade values Size 20 = 0201 18 = 1206 11 = 2020 05 = 0402 14 = 1210 09 = 2045 16 = 0603 13 = 1217 01 = 2512 10 = 0805 12 = 2010 Termination Material Sn = Leave Blank Au = G Series CT = Thin Film Precision Resistors Wire Bond Pads Terminal Material: Au
FEATURES
Nichrome Thin Film Resistor Element CTG type constructed with top side terminations, wire bonded pads, and Au termination material. Anti-Leaching Nickel Barrier Terminations Very Tight Tolerances, as low as ±0.02% Extremely Low TCR, as low as ±1ppm Special Sizes available 1217, 2020, and 2045 Either ISO 9001 or ISO/TS 16949:2002 Certified Applicable Specifications: EIA575, IEC 60115-1, JIS C5201-1, CECC 40401, MIL-R-55342D
American Accurate Components, Inc. THIN FILM PRECISION CHIP RESISTORS The content of this specification may change without notification 10/12/07 TEL: 949-453-9888 FAX: 949-453-8889
ELECTRICAL CHARACTERISTICS
at 70° (W) Resistance Range ±% Tolerance TCR (10 -6/°C) Working Voltage Overload Voltage Operating Temp Range 10.0 ~ 30.0 1 ±100 0201 0.05 33.0 ~ 22.0K 0.5 ±25 15V 30V -55°C ~ +125°C 0402 0.031 0.063 50V 100V -55°C ~ +125°C -55°C ~ +155°C 102K ~ 270K 0.05, 0.1, 0.25, 0.5, 1 10, 25, 50 0603 0.063 0.100 274K ~ 360K 0.1, 0.25, 0.5, 1 10, 25, 50 75V 150V -55°C ~ +125°C 205K ~ 360K 0.05, 0.1, 0.25, 0.5 10, 25, 50 365K ~ 487K 0.05, 0.1, 0.25, 0.5 10, 25 0805 0.100 499K ~ 1.00M 0.1, 0.5 25 100V 200V -55°C ~ +125°C 1206 0.125 150V 300V -55°C ~ +125°C 100 ~ 330K 0.1 ±5, ±10 1210 0.250 200V 400V -55°C ~ +125°C 10.0 ~500K 0.01, 0.05 ±25 10.0 ~500K 0.01, 0.05 2010 0.250 ±50 150V 300V -55°C ~ +125°C 10.0R ~ 500K 0.01, 0.05 ±25 10.0R ~ 500K 0.01, 0.05 2512 0.500 ±50 150V 300V -55°C ~ +125°C * Rated Voltage: √PxR ** 0.01% may be available under special request
American Accurate Components, Inc. THIN FILM PRECISION CHIP RESISTORS The content of this specification may change without notification 10/12/07 TEL: 949-453-9888 FAX: 949-453-8889 PERFORMANCE & ENVIRONMENTAL SPECIFICATIONS Maximum ∆ Ω +0.05Ω (Tolerance) Test Item A B, C D, F Condition Short Time Overload ± 0.1% ± 0.1% ± 0.5% 2.5 ti mes of the rated voltage shall be applied for 5 seconds Load Life ± 0.1% ± 0.25% ± 0.5% The resistor shall be subjected to rated voltage for 90 min. followed by a pause of 30 min. at a temperature of 70±3ºC. This constitutes 1 cycle. Cycles shall be repeated for 1000 hours. Moisture Load Life ± 0.1% ± 0.25% ± 0.5% The resistor subjected to rated voltage for 90 min followed by a pause for 30 min at a temperature of 60±2ºC with relative humidity of 90% to 95%. This constitutes 1 cycles. Cycles shall be repeated for 1000 hours. 5 continuous cycles Resistance to Solder Heat ± 0.05% ± 0.1% ± 0.5% The resistor shall withstand dipped into solder for 10±1 sec. At 260±5ºC Terminal Strength ± 0.1% ± 0.1% ± 0.5% Dist ance between fulcrums: 90mm; Bending width: 3 mm Solderability A new uniform coating of solder shall cover minimum of 95% of surface being immersed The resistor shall be dipped into the solder of 235±5ºC for 3±0.5 seconds Insulation Resistance DC 500V for 1 minute 1000 Meg Ω or over VALUE MARKING For those parts ordered with an E-24 value, the product will be marked with a 3 digit code. For those products ordered with an E-96 value, the product will be marked with a 4 digit code. For those parts which fall under E-96 and E-24 values (e.g. 1K ohm is both an E-96 and E-24 value), the part will be marked with a 3 digit code; 4 digit markings for this type is available upon special request. 0201, and 0402 Size No marking E-24 & E-96 Values Custom Value Any Size
0603 Size
EIA 96 Digit Code of 3.32K ohm E-96 Values 0603 ~ 2512 Sizes EIA 3 Digit Code of 10K ohm resistor E-24 Values, E-96 Values 0805 ~ 2512 Sizes EIA 4 Digit Code of 121K ohm resistor E-96 Values LABEL DESCRIPTION One side surface of a reel is marked with a label with the following items of information. 1. Chip Resistor 2. Part Number 3. Tolerance 4. Quantity 5. Lot number for production month/year* 6. Manufacturer’s name or symbol * The suffix “L” indicates that this item is lead free. As of September 2004, all new production items of the series CR and CJ are no longer containing tin/lead (SnPb) terminals; they are lead free and in compliance with Lead Free/RoHS. PACKAGE QUANTITY Type 0201 0402 0603 0805 1206 M 5,000 10,000 5,000 5,000 5,000 O 1,000 1,000 1,000 1,000 1,000 Type 1210 1217 2010 2020 2045 2512 B 5,000 2,000 4,000 2,000 3,000 4,000 O 1,000 1,000 1,000 1,000 1,000 1,000 REEL SCHEMATIC & DIMENSIONS (mm) O & M Type M Type 7” Reel 13” Reel C ∅13± 0.2 ∅13±0.2 E 60±0.5 100 ±0.2 G 9.0±0.3 9.5 ±0.5 H 1.5±0.3 2.0 ±0.5 Reel size is dependent upon the package quantity& resistor size. Call for more info. TAPE SCHEMATIC TAPE DIMENSIONS (mm) 0201 0402 0603 0805 1206 1210 1217 2010 2020 2045 2512 Call to find out if the tape material is paper or plastic 51B 1213 103