CT100 EXTECH | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 1

Technical content

CT100 Network Cable Tester Introduction Congratulations on your purchase of the Extech CT100 Network Cable Tester System. The system consists of a Transmitter and a Receiver. This system automatically performs the following tests: Continuity, Open/Short Circuits, and Wire Crosses (Reversals). The CT100 tests “F” type coaxial and RJ45 terminated cables meeting the following wiring standards:

  • 10Base-T
  • EIA/TIA 568B
  • AT&T258A
  • Token Ring Operation WARNING: Do NOT test on LIVE CIRCUITS 1. Power the transmitter by moving the ON/OFF switch to the ON position. The power LED will light. 2. To test a patch cable, connect one end of the cable under test to the Transmitter and the other end to the Receiver. Testing begins automatically and is indicated by the stepping action of the LEDs on the Receiver. (Note: To test cabling that is part of an installation, the Transmitter and Receiver must be connected in line with the installation. Patch-cords needed to connect from wall-plates to the Transmitter and Receiver must be provided by the user.) 3. Test result examples are listed below: Battery Replacement (Transmitter only) 1. Turn power OFF on the Transmitter, disconnect any cables, and remove the Transmitter’s rear screw to access the battery compartment. (The Receiver does not contain batteries). 2. Replace the two ‘AAA’ 1.5V batteries and re-assemble the Transmitter. Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date o f shipment (a six month limited warranty applies on sensors and cables). If it should become necessary to return the instrument for service during or beyond the warrant y period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorizati on or visit our website at www.extech.com (click on ‘Contact Extech’ and go to ‘Service Department’ to request an RA number). A Return Authorization (RA) number must be issued bef ore any product is returned to Extech. The sender is responsible for shipping charg es, freight, insurance and proper packaging to prevent damage in transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper w iring, operation outside of specification, improper maintenance or repair, or unauthorized modification. Extech s pecifically disclaims any impli ed warranties or merchantability or fitness for a specific pur pose and will not be liable for any direct, indirect, incidental or conseq uential damages. Extech's total liability is limited to repai r or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or implied. Copyright © 2002 Extech Instruments Corporation. All rights reserved including the right of reproduction in whole or in part in any form. Website: www.extech.com Email: support@extech.com Rev 1.0 9/02 1 2 3 4 5 6 7 8 PR3 PR1 PR4 PR2 1 2 3 4 5 6 7 8 PR2 PR1 PR4 PR3 1 2 3 4 5 6 7 8 PR1 PR2 EIA/TIA 568A 1 2 3 4 5 6 7 8 PR2 PR1 EIA/TIA 568B (AT&T 258A) 10Base-T Token Ring

4 Pair Test

Pass = Green x 4 Fail = Red or No Light Pass = Green x 4 Fail = Red or No Light

2 Pair Test (1-2 and 3-6)

Pass = Green x 2 Fail = Red or No Light

2 Pair Test (3-6 and 4-5)

Pass = Green x 2 Fail = Red or No Light Coax Pass = Green x 1 Fail = Red or No Light 1 2 3 4 5 6 7 8 PR3 PR1 PR4 PR2 Screened (Shielded) Cable

4 Pair + Shield Test

Pass = Green x 5 Fail = Red or No Light