CRO6000Z ZCOMM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
-150 -140 -130 -120 -110 -100 -90 -80 -70 -60
1 E+3 10 E+3 100 E+3
4±2 5990 0.5 - 4.5 -108 -18 <0.05 -40 to 85 Oscillation Frequency Range Phase Noise @ 10 kHz offset (1 Hz BW, typ.) Harmonic Suppression (2nd, typ.) Tuning Voltage Tuning Sensitivity (avg.) Power Output Load Impedance Input Capacitance (max.) Pushing Pulling (14 dB Return Loss, Any Phase) Operating Temperature Range Package Style VCO-24H MHz dBc/Hz dBc Vdc MHz/V dBm pF MHz/V MHz Vdc mA Supply Voltage (Vcc, nom.) Supply Current (Icc, typ.) All specifications are typical unless otherwise noted and subject to change without notice. PHASE NOISE (1 Hz BW, typical) © Z-Communications, Inc. All rights reservedPage 1 VOLTAGE CONTROLLED OSCILLATOR
FEATURES
APPLICATIONS
PERFORMANCE SPECIFICATIONS VALUE UNITS POWER SUPPLY REQUIREMENTS APPLICATION NOTES 5990 6010- MHz• Frequency Range:
- Tuning Voltage: 0.5 - 4.5 Vdc - Style PackageVCO-24H A1Rev
- AN-100/1 : Mounting and Grounding of VCOs
- AN-102 : Proper Output Loading of VCOs
- AN-107 : How to Solder Z-COMM VCOs NOTES: Fundamental Rejection (typ.): -40 dBc Phase Noise @ 100 kHz offset (1 Hz BW, typ.): -128 dBc/Hz
9939 Via Pasar • San Diego, CA 92126
TEL (858) 621-2700 FAX (858) 621-2722 -6010 OFFSET (Hz) £(f) (dBc/Hz)
5963 5971 5978 5985 5992 6000 6008 6016 6024 6031 LOW COST - HIGH PERFORMANCE VOLTAGE CONTROLLED OSCILLATOR © Z-Communications, Inc. Page 2 Printed in the U.S.A. CRO6000Z TUNING CURVE, typ. POWER CURVE, typ. PAGE 2 PHYSICAL DIMENSIONS -40 °c25 0.220 .032 8 10 12 24 22 20 .015 .030 .055 DETAIL B (TYP) SEE DETAIL A SEE DETAIL B TABS RANGE: SEE NOTE 5 (4 PLACES) DETAIL A PIN 1 91 1 2123 TOP BOTTOM (3 PLACES) 0.025 0.178 0.263 0.348 0.433 0.518 0.603 0.688 0.000 0.866 0.026 0.141 0.226 0.311 0.396 0.481 0.606 0.000 0.631 0.841 VCO-24H 415-0096 REV. A (DRAWING NOT TO SCALE) 1. The inside radius of all 24 half holes at the perimeter of the board are plated to provide a surface for the attachment of the VCO Module to the PCB. 21 pads are for grounding. 2. The surface of the shield is tin-plated and may be soldered to. The shield's base metal is cold rolled steel. 3.The ground plane on the bottom side is ground and attaches to a ground track on the top side of the board as well as to the shield. 4. Unless otherwise noted all dimensions are in inches. 5. Unless otherwise noted all tolerances are as follows: .xxx = ± .010 P1 RF OUTPUT P2-12 GROUND P13 VCC P14-16 GROUND P17 Vtune P18-24 GROUND TUNING VOLTAGE (Vdc) FREQUENCY (MHz) POWER OUTPUT (dBm) FREQUENCY (MHz)