CPS-P325 ADLINK | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Features
- Supports -25 °C to +70 °C operating temperature
- Compliant to PICMG 2.11
- Wide range AC input with PFC
- Extremely high efficiency and high power density
- Low inrush current
- 4 high current outputs with flexible load distribution
- Integrated ORing FETs / diodes for true redundancy
- Inhibit and enable inputs
- Remote sense lines
- Single-wire current share function for 3 outputs
- Hot-swap capability
- 47-pin connector
- Overtemperature, overvoltage, overcurrent, and overpower protection Specifications
- cPS-P325/AC PICMG® Standards PICMG® 2.11 CompactPCI® Power Interface compliant Form Factor: 3U cPCI (100 x 160mm), 2-slot (8HP) wide Input Voltage: 100-240 ± 10% VAC Input Frequency: 50-60 ±5% Hz Input Current: 3.6A @ 230VAC 4A @ 260VAC Inrush Current: <15A @ 240VAC Power Factor (PFC, only for AC): Correction Typical 0.95 Meets Harmonic Correction EN 61000-3-2 Output Voltage/Current 5V: Typ. 25A, Max. 40A 3.3V: Typ. 20A, Max. 40A +12V: Typ. 4A, Max. 5.5A -12V: Typ. 1A, Max. 2A Max. load is the continuous operating load of each rail individually. The max. load of each rail cannot be drawn from all outputs simultaneously. Output Voltage: 1.5A @+12V Minimum Load Output Wattage: Typical 250W continuous Line Regulation: max + - 10mV Load Regulation +12V: + - 30mV -12V: -380 mV Ripple 60 mV @ +5 V and 3.3 V outputs 120 mV @ +12 V and -12 V outputs Hold-up Time: 20 ms after power fail signal Efficiency: Typical 81.5-82.6% Output Voltage Sense Available at 5V, 3.3V, and +12V outputs and current sharing N+1 Redundancy Equipped with internal OR-ing diodes at all outputs for N+1 redundancy operation Remote ON/OFF: Available at [INH#] & [EN#] Power Failure Signal: Available at [FAL#] pin Power Degradation Signal: Available at [DEG#] pin
www.adlinktech.com All products and company name listed are trademarks or trade names of their respective companies. Updated Mar. 10, 2017. ©2017 ADLINK Technology, Inc. All Rights Reserved. All specifications are subject to change without further notice.
Ordering Information
- cPS-P325/AC PICMG 47-pin hot-swap redundant 3U CompactPCI 8HP 250 W power module with universal AC Input Specifications Protections Over Temperature Protection (OTP): TC ≥+105 °C Over Current Protection (OCP): Installed at each rail Over Load Protection (OLP): Typical 120% max. load, fully protected against output overload or short circuit. Over Voltage Protection (OVP): Built-in at all outputs Status LED <Green LED> [POWER] means valid input voltage <Amber LED> [FAUL T] means a critical fault Earth Leakage: 1.18mA at 254Vac/60Hz Operating Temperature -25˚C to 70˚C (-25˚C to +50˚C at full load with specified air flow. Derates linearly to 50% at +70˚C.) Storage Temperature -40˚C to +85˚C Humidity 5% to 95% non-condensing Shock 20G Acceleration amplitude,11 ms duration, converter operation Vibration Operation: 4.9 Grms, 20-500Hz, each axis Cooling Requirement: Min. 400 LFM (2 m/s) is required for typical full power rating Certifications IEC/EN 60950-1 2nd Ed, UL/CSA 60950-1 2nd Ed & China CCC