82C88_05 INTERSIL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

Features

  • Compatible with Bipolar 8288
  • Performance Compatible with: -8 0 8 9
  • Provides Advanced Commands for Multi-Master Busses
  • Three-State Command Outputs
  • Bipolar Drive Capability
  • Scaled SAJI IV CMOS Process
  • Single 5V Power Supply
  • Low Power Operation
  • Operating Temperature Ranges
  • Pb-Free Plus Anneal Available (RoHS Compliant) 1IOB CLK ALE GND DT/ R AEN MRDC AMWC MWTC VCC MCE/PDEN DEN CEN IORC AIOWC IOWC INTA 91 0 1 1 1 2 13 321 2 0 1 9 ALE DT/ R AEN MRDC AMWC GND IORC AIOWC IOWC MWTC VCC IOB CLK DEN CEN MCE/PDEN INTA

Ordering Information

(°C) PKG. DWG. # CP82C88 CP82C88 20 Ld PDIP 0 to +70 E20.3 CP82C88Z (Note) CP82C88Z 20 Ld PDIP (Pb-free) 0 to +70 E20.3 CP82C88-10 CP82C88-10 20 Ld PDIP 0 to +70 E20.3 IP82C88 IP82C88 -40 to +85 E20.3 CS82C88 CS82C88 20 Ld PLCC 0 to +70 N20.35 IS82C88 IS82C88 -40 to +85 N20.35 CD82C88 CD82C88 20 Ld CERDIP 0 to +70 F20.3 ID82C88 ID82C88 -40 to +85 F20.3 MD82C88/B MD82C88/B -55 to +125 F20.3 8406901RA 8406901RA SMD# F20.3 MR82C88/B MR82C88/B 20 Pad CLCC -55 to +125 J20.A 84069012A 84069012A SMD# J20.A NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. Data Sheet FN2979.2 August 25, 2005 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2002, 2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners.

2 FN2979.2 August 25, 2005 Functional Diagram Pin Description PIN SYMBOL NUMBER TYPE DESCRIPTION VCC 20 V CC: The +5V power supply pin. A 0.1µF capacitor between pins 10 and 20 is recommended for decoupling. GND 10 GROUND. S0, S1, S2 19, 3, 18 I STATUS INPUT PINS: These pins are the input pins from the 80C86, 80C88,8086/88, 8089 processors. The 82C88 decodes these inputs to generate command and control signals at the appropriate time. When Status pins are not in use (passive), command outputs are held HIGH (See Table1). CLK 2 I CLOCK: This is a CMOS compatible input which re ceives a clock signal from the 82C84A or 82C85 clock generator and serves to establish when command/control signals are generated. ALE 5 O ADDRESS LATCH ENABLE: This signal serves to st robe an address into the address latches. This signal is active HIGH and latching occurs on the falling (HIGH to LOW) transition. ALE is intended for use with transparent D type latches, such as the 82C82 and 82C83H. DEN 16 O DATA ENABLE: This signal serves to enable data trans ceivers onto either the local or system data bus. This signal is active HIGH. DT/R 4 O DATA TRANSMIT/RECEIVE: This signal establishes the di rection of data flow through the transceivers. A HIGH on this line indicates Transmit (write to I/O or memory) and a LOW indicates Receive (read from I/O or memory). AEN 6 I ADDRESS ENABLE: AEN enables command outputs of the 82C88 Bus Controller a minimum of 110ns (250ns maximum) after it becomes active (LOW). AEN going inactive immediately three-states the command output drivers. AEN does not affect the I/O command lines if the 82C88 is in the I/O Bus mode (IOB tied HIGH). CEN 15 I COMMAND ENABLE: When this signal is LOW al l 82C88 command outputs and the DEN and PDEN control outputs are forced to their Inactive state. When this signal is HIGH, these same outputs are enabled. IOB 1 I INPUT/OUTPUT BUS MODE: When t he IOB pin is strapped HIGH, the 82C88 functions in the I/O Bus mode. When it is strapped LOW, the 82C88 functions in the System Bus mode (See I/O Bus and System Bus sections). AIOWC 12 O ADVANCED I/O WRITE COMMAND: The AIOWC issues an I/O Write Command earlier in the machine cycle to give I/O devices an early indication of a write instruction. Its timing is the same as a read command signal. AIOWC is active LOW. IOWC 11 O I/O WRITE COMMAND: This command line instructs an I/O device to read the data on the data bus. The signal is active LOW. IORC 13 O I/O READ COMMAND: This command line instructs an I/O device to drive its data onto the data bus. This signal is active LOW. VCC GND COMMAND SIGNALS MULTIBUSTM CONTROL INPUT IOB CEN CLK AEN CONTROL SIGNAL GENERATOR DEN ALE DT/R MCE/PDEN COMMAND SIGNAL GENERATOR AIOWC IOWC AMWC MWTC MRDC IORCS2 INTA ADDRESS LATCH, DATA TRANSCEIVER, AND INTERRUPT CONTROL SIGNALS CONTROL LOGIC STATUS DECODER 82C8882C88

determine what command is to be issued (see Table 1). involved when the CPU wants to gain access to the I/O bus. exist in a multi-processor system. line) when the bus is free for use. Both memory and I/O commands wait for bus arbitration. and memory are shared by more than one processor. place vectoring information onto the data bus. bus. This signal is active LOW. acknowledged and that it should drive vectoring information onto the data bus. This signal is active LOW. for the I/O bus that DEN performs for the system bus. PDEN is active LOW. TABLE 1. COMMAND DECODE DEFINITION

111 P a s s i v e N o n e

4 FN2979.2 August 25, 2005 Control Outputs The control outputs of the 82C88 are Data Enable (DEN), Data Transmit/Receive (DT/R) and Master Cascade Enable/ Peripheral Data Enable (MCE/PDEN). The DEN signal determines when the external bus should be enabled onto the local bus and the DT/R determines the direction of data transfer. These two signals usually go to the chip select and direction pins of a transceiver. The MCE/PDEN pin changes function with the two modes of the 82C88. When the 82C88 is in the IOB mode (IOB HIGH), the PDEN signal serves as a dedicated data enable signal for the I/O or Peripheral System bus. Interrupt Acknowledge and MCE The MCE signal is used during an interrupt acknowledge cycle if the 82C88 is in the System Bus mode (IOB LOW). During any interrupt sequence, there are two interrupt acknowledge cycles that occur back to back. During the first interrupt cycle no data or address transfers take place. Logic should be provided to mask off MCE during this cycle. Just before the second cycle begins the MCE signal gates a master Priority Interrupt Controller’s (PIC) cascade address onto the processor’s local bus where ALE (Address Latch Enable) strobes it into the address latches. On the leading edge of the second interrupt cycle, the addressed slave PIC gates an interrupt vector onto the system data bus where it is read by the processor. If the system contains only one PIC, the MCE signal is not used. In this case, the second Interrupt Acknowledge signal gates the interrupt vector onto the processor bus. Address Latch Enable and Halt Address Latch Enable (ALE) occurs during each machine cycle and serves to strobe the current address into the 82C82/82C83H address latches. ALE also serves to strobe the status (S0 , S1, S2) into a latch for halt state decoding. Command Enable The Command Enable (CEN) input acts as a command qualifier for the 82C88. If the CEN pin is high, the 82C88 functions normally. If the CEN pin is pulled LOW, all command lines are held in their inactive state (not three- state). This feature can be used to implement memory partitioning and to eliminate address conflicts between system bus devices and resident bus devices. 82C8882C88

5 FN2979.2 August 25, 2005 Absolute Maximum Ratings Thermal Information Operating Conditions Operating Temperature Range Thermal Resistance (Typical) θ JA (°C/W) θJC (°C/W) Maximum Junction Temperature (PLCC - Lead Tips Only) Die Characteristics CAUTION: Stresses above those listed in “Abs olute Maximum Ratings” may cause permanent dam age to the device. This is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. TA = 0°C to +70°C (C82C88); TA = -40°C to +85°C (I82C88); TA = -55°C to +125°C (M82C88) SYMBOL PARAMETER MIN MAX UNITS TEST CONDITIONS VIH Logical One Input Voltage 2.0 2.2 V V C82C88, I82C88 M82C88 VIL Logical Zero Input Voltage - 0.8 V VIHC CLK Logical One Input Voltage V CC -0.8 - V VILC CLK Logical Zero Input Voltage - 0.8 V VOH Output High Voltage Command Outputs 3.0 VCC -0.4 V IOH = -8.0mA IOH = -2.5mA Output High Voltage Control Outputs 3.0 VCC -0.4 V IOH = -4.0mA IOH = -2.5mA VOL Output Low Voltage Command Outputs -0 . 5 V I OL= +12.0mA Output Low Voltage Control Outputs -0 . 4 V I OL = +8.0mA II Input Leakage Current -1.0 1.0 µAV IN = GND or VCC, except S0, S1, S2, DIP Pins 1-2, 6, 15 IBHH Input Leakage Current-Status Bus -50 -300 µAV IN = 2.0V, S0, S1, S2 (See Note 1) IO Output Leakage Current -10.0 10.0 µAV O = GND or VCC, IOB = GND, AEN = VCC, DIP Pins 7-9, 11-14 ICCSB Standby Power Supply - 10 µAV CC = 5.5V, VIN = VCC or GND, Outputs Open ICCOP Operating Power Supply Current - 1 mA/MHz V CC = 5.5V, Outputs Open (See Note 2) NOTES: 1. IBHH should be measured after raising the V IN on S0, S1, S2 to VCC and then lowering to valid input high level of 2.0V. 2. ICCOP = 1mA/MHz of CLK cycle time (TCLCL) Capacitance TA = +25°C SYMBOL PARAMETER TYPICAL UNITS TEST CONDITIONS CIN Input Capacitance 10 pF FREQ = 1MHz, all measurements are referenced to device GNDCOUT Output Capacitance 17 pF 82C8882C88

6 FN2979.2 August 25, 2005 TA = 0°C to +70°C (C82C88); TA = -40°C to +85°C (I82C88); TA = -55°C to +125°C (M82C88) SYMBOL PARAMETER 8MHz 10MHz 12MHz UNITS TEST CONDITIONSMIN MAX MIN MAX MIN MAX TIMING REQUIREMENTS (1) TCLCL CLK Cycle Period 125 - 100 - 83 - ns (2) TCLCH CLK Low Time 55 - 50 - 34 - ns (3) TCHCL CLK High Time 40 - 37 - 34 - ns (4) TSVCH Status Active Setup Time 35 - 35 - 35 - ns (5) TCHSV Status Inactive Hold Time 10 - 10 - 5 - ns (6) TSHCL Status Inactive Setup Time 35 - 35 - 35 - ns (7) TCLSH Status Active Hold Time 10 - 10 - 5 - ns TIMING RESPONSES (8) TCVNV Control Active Delay 5 45 5 45 5 45 ns 1 (9) TCVNX Control Inactive Delay 10 45 10 45 10 35 ns 1 (10) TCLLH ALE Active Delay (from CLK) - 20 - 20 - 20 ns 1 (11) TCLMCH MCE Active Delay (from CLK) - 25 - 23 - 23 ns 1 (12) TSVLH ALE Active Delay (from Status) - 20 - 20 - 20 ns 1 (13) TSVMCH MCE Active Delay (from Status) - 30 - 23 - 23 ns 1 (14) TCHLL ALE Inactive Delay 4 18 4 18 4 18 ns 1 (15) TCLML Command Active Delay 5 35 5 35 5 35 ns 2 (16) TCLMH Command Inactive Delay 5 35 5 35 5 35 ns 2 (17) TCHDTL Direction Control Active Delay - 50 - 50 - 50 ns 1 (18) TCHDTH Direction Control Inactive Delay - 30 - 30 - 30 ns 1 (19) TAELCH Command Enable Time (Note 1) - 40 - 40 - 40 ns 3 (20) TAEHCZ Command Disable Time (Note 2) -4 0-4 0-4 0 n s 4 (21) TAELCV Enable Delay Time 110 250 110 250 110 250 ns 2 (22) TAEVNV AEN to DEN - 25 - 25 - 25 ns 1 (23) TCEVNV CEN to DEN, PDEN -2 5-2 5-2 5 n s 1 (24) TCELRH CEN to Command - TCLML +10 -T C L M L-T C L M L n s 2 (25) TLHLL ALE High Time TCLCH - - TCLCH - - TCLCH - nn s 1 NOTES: 1. TAELCH measurement is between 1.5V and 2.5V. 2. TAEHCZ measured at 0.5V change in VOUT. 82C8882C88

and VCC -0.4V. Input rise and fall times are driven at 1ns/V. TABLE 2. TEST CONDITION DEFINITION TABLE

8 FN2979.2 August 25, 2005 Timing Waveforms (Note 3) NOTES: 1. Address/Data Bus is shown only for reference purposes. 2. Leading edge of ALE and MCE is determined by the falling edge of CLK or status going active. Whichever occurs last. 3. All timing measurements are made at 1.5V unless otherwise specified. FIGURE 1. STATE CLK S2, S1, S0 ADDRESS/DATA ALE MRDC, IORC, INTA, AMWC, AIOWC MWTC, IOWC DEN (READ) (INTA) PDEN (READ) (INTA) DEN (WRITE) PDEN (WRITE) DT/R (READ) (INTA) MCE T4 T1 T2 T3 T4 TCLCL (1) TCLCH (2) TCHCL (3) TCLSH (7) TSHCL (6)TSVCH (4) TCHSV (5) TCLLH (10) TSVLH (12) TCHLL (14) TCLML (15) TCLML (15) TCLMH (16) TCVNX (9) TCVNV (8) TCVNV (8) TCVNX (9) TCHDTH (18) TCHDTL (17) TCHDTH (18) TCLMCH (11) TSVMCH (13) TCVNX (9) 1WRITE DATA VALID ADDRESS VALID 82C8882C88

10 FN2979.2 August 25, 2005 Burn-In Circuits MD82C88 CERDIP MR82C88 CLCC NOTES: 1. V CC = 5.5V ± 0.5V GND = 0V 2. V IH = 4.5V ± 10% VIL = -0.2V to +0.4V 3. Component Values: C1 = 0.01µF (Min) F0 = 100kHz ± 10% F1 = F0/2 VCC A A A VCC A A A VCC A A A A A A 91 0 1 1 1 2 13 3 2 1 20 19 VCC/ 2 VCC/ 2 VCC/ 2 R4 R4 R4R4 VCC/ 2VCC/ 2 R1R4 R1 R4 VCCF0 F7F3 F4 VCC/ 2 VCC/ 2 VCC/ 2 VCC/ 2 VCC 82C8882C88

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnishe d by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN2979.2 August 25, 2005 Die Characteristics DIE DIMENSIONS: 103.5 x 116.5 x 19 ± 1mils METALLIZATION: Type: Si - Al Thickness: 11k Å ± 2kÅ GLASSIVATION: Type: Nitrox Thickness: 10kÅ WORST CASE CURRENT DENSITY: 1.9 x 105 A/cm2 Metallization Mask Layout 82C88 S1 CLK IOB V CC S0 S2 MCE/ DEN CEN INTA IORCAIOWCIOWCGNDMWTCAMWC MRDC AEN ALE DT/R PDEN 82C88