CP3BT23

CP3BT23 TI1 | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 260

Technical content

CP3BT23 Reprogrammable Connectivity Processor with Bluetooth and Dual CAN Interfaces Literature Number: SNOSAE2D

©2007 National Semiconductor Corporation www.national.com CP3BT23 Reprogrammable Connectivity Processor with Bluetooth and Dual CAN Interfaces FEBRUARY 2007 CP3BT23 Reprogrammable Connectivity Processor with Bluetooth® and Dual CAN Interfaces

1.0 General Description

The CP3BT23 connectivity processor combines high perfor- mance with the massive integration needed for embedded Bluetooth applications. A powerful RISC core with on-chip SRAM and Flash memory provides high computing band- width, hardware communications peripherals provide high- I/O bandwidth, and an external bus provides system ex- pandability. On-chip communications peripherals include: Bluetooth Lower Link Controller, dual CAN controllers, Microwire/Plus, SPI, ACCESS.bus, quad UART, 12-bit A/D converter, and Advanced Audio Interface (AAI). Additional on-chip periph- erals include Random Number Generator (RNG), DMA con- troller, CVSD/PCM conversion module, Timing and Watchdog Unit, Versatile Timer Unit, Multi-Function Timer, and Multi-Input Wake-Up (MIWU) unit. Bluetooth hand-held devices can be both smaller and lower in cost for maximum consumer appeal. The low voltage and advanced power-saving modes achieve new design points in the trade-off between battery size and operating time for handheld and portable applications. In addition to providing the features needed for the next gen- eration of embedded Bluetooth products, the CP3BT23 is backed up by the software resources designers need for rapid time-to-market, including an operating system, Blue- tooth protocol stack implementation, peripheral drivers, ref- erence designs, and an integrated development environment. Combined with a Bluetooth radio transceiver such as National’s LMX5252, the CP3BT23 provides a com- plete Bluetooth system solution. National Semiconductor offers a complete and industry- proven application development environment for CP3BT23 applications, including the IAR Embedded Workbench, iSYSTEM winIDEA and iC3000 Active Emulator, Bluetooth Development Board, Bluetooth Protocol Stack, and Applica- tion Software. Block Diagram CPU Core Bus

12 MHz and 32 kHz

4.5K Bytes Data RAM 1K Byte Sequencer RAM DS283 256K Bytes Flash Program Memory 8K Bytes Flash Data 32K Bytes Static RAM CR16C CPU Core ACCESS .bus Dual CAN 2.0B Controller Random Number Generator Bluetooth is a registered trademark of Bluetooth SIG, Inc. and is used under license by National Semiconductor. TRI-STATE is a registered trademark of National Semiconductor Corporation. Obsolete

www.national.com 2 CP3BT23 Table of Contents Obsolete

3 www.national.com CP3BT23

2.0 Features

! Fully static RISC processor core, capable of operating from 0 to 24 MHz with zero wait/hold states ! Minimum 41.7 ns instruction cycle time with a 24-MHz in- ternal clock frequency, based on a 12-MHz external input ! 47 independently vectored peripheral interrupts On-Chip Memory ! 256K bytes reprogrammable Flash program memory ! 8K bytes Flash data memory ! 32K bytes of static RAM data memory ! Addresses up to 12M bytes of external memory Broad Range of Hardware Communications Peripherals ! Bluetooth Lower Link Controller (LLC) including a shared 4.5K byte Bluetooth RAM and 1K byte Bluetooth Se- quencer RAM ! ACCESS.bus serial bus (compatible with Philips I 2C bus) ! Dual CAN interface with 15 message buffers conforming to CAN specification 2.0B active ! 8/16-bit SPI, Microwire/Plus serial interface ! Four-channel Universal Asynchronous Receiver/Trans- mitter (UART), one channel has USART capability ! Advanced Audio Interface (AAI) to connect to external 8/ 13-bit PCM Codecs as well as to ISDN-Controllers through the IOM-2 interface (slave only) ! CVSD/PCM converter supporting one bidirectional audio connection General-Purpose Hardware Peripherals ! 12-bit A/D Converter (ADC) ! Dual 16-bit Multi-Function Timer (MFT) ! Versatile Timer Unit with four subsystems (VTU) ! Four-channel DMA controller ! Timing and Watchdog Unit ! Random Number Generator peripheral Extensive Power and Clock Management Support ! On-chip Phase Locked Loop ! Support for multiple clock options ! Dual clock and reset ! Power-down modes Flexible I/O ! Up to 56 general-purpose I/O pins (shared with on-chip peripheral I/O) ! Programmable I/O pin characteristics: TRI-ST ATE out- put, push-pull output, weak pull-up input, high-imped- ance input ! Schmitt triggers on general-purpose inputs ! Multi-Input Wake-Up (MIWU) capability Power Supply ! I/O port operation at 2.5V to 3.3V ! Core logic operation at 2.5V ! On-chip power-on reset Temperature Range ! -40°C to +85°C (Industrial) Packages ! LQFP-128, LQFP-144 Complete Development Environment ! Pre-integrated hardware and software support for rapid prototyping and production ! Integrated environment ! Project manager ! Multi-file C source editor ! High-level C source debugger ! Comprehensive, integrated, one-stop technical support Bluetooth Protocol Stack ! Applications can interface to the high-level protocols or directly to the low-level Host Controller Interface (HCI) ! Transport layer support allows HCI command-based in- terface over UART port ! Baseband (Link Controller) hardware minimizes the bandwidth demand on the CPU ! Link Manager (LM) ! Logical Link Control and Adaptation Protocol (L2CAP) ! Service Discovery Protocol (SDP) ! RFCOMM Serial Port Emulation Protocol ! All packet types, piconet, and scatternet functionality supported CP3BT23 Connectivity Processor Selection Guide NSID Speed (MHz) Temp. Range Program Flash (Kbytes) Data Flash (Kbytes) SRAM (Kbytes) External Address Lines I/Os Package Type CP3BT23G18AWM NOPB 24 -40 ° to +85°C 256 8 32 0 56 LQFP-128 CP3BT23G18AWMX NOPB 24 -40 ° to +85°C 256 8 32 0 56 LQFP-128 CP3BT23Y98AWM NOPB 24 -40° to +85 °C 256 8 32 23 50 LQFP-144 CP3BT23Y98AWMX NOPB 24 -40 ° to +85°C 256 8 32 23 50 LQFP-144 AWM - Erased part (Bluetooth device address in Information Block 1); X - Tape and reel; NOPB - No lead solder Obsolete

www.national.com 4 CP3BT23

3.0 Device Overview

The CP3BT23 connectivity processor is a complete micro- computer with all system timing, interrupt logic, program memory, data memory, and I/O ports included on-chip, mak- ing it well-suited to a wide range of embedded applications. The block diagram on page 1 shows the major on-chip com- ponents of the CP3BT23 devices.

3.1 CR16C CPU CORE

The CP3BT23 device implements the CR16C CPU core module. The high performance of the CPU core results from the implementation of a pipelined architecture with a two- bytes-per-cycle pipelined system bus. As a result, the CPU can support a peak execution rate of one instruction per clock cycle. For more information, please refer to the CR16C Program- mer’s Reference Manual (document number 424521772- 101, which may be downloaded from National’s web site at http://www.national.com).

3.2 MEMORY

The CP3BT23 devices support a uniform linear address space of up to 16 megabytes. Three types of on-chip mem- ory occupy specific regions within this address space, along with any external memory: ! 256K bytes of Flash program memory ! 8K bytes of Flash data memory ! 32K bytes of static RAM ! Up to 12M bytes of external memory (144-pin devices) The 256K bytes of Flash program memory are used to store the application program, Bluetooth protocol stack, and real- time operating system. The Flash memory has security fea- tures to prevent unintentional programming and to prevent unauthorized access to the program code. This memory can be programmed with an external programming unit or with the device installed in the application system (in-sys- tem programming). The 8K bytes of Flash data memory are used for non-vola- tile storage of data entered by the end-user, such as config- uration settings. The 32K bytes of static RAM are used for temporary storage of data and for the program stack and interrupt stack. Read and write operations can be byte-wide or word-wide, de- pending on the instruction executed by the CPU. Up to 12M bytes of external memory can be added on an external bus. The external bus is only available on devices in 144-pin packages. For Flash program and data memory, the device internally generates the necessary voltages for programming. No ad- ditional power supply is required.

3.3 INPUT/OUTPUT PORTS

The device has up to 50 software-configurable I/O pins, or- ganized into seven ports called Port B, Port C, Port E, Port G, Port H, Port I, and Port J. Each pin can be configured to operate as a general-purpose input or general-purpose out- put. In addition, many I/O pins can be configured to operate as inputs or outputs for on-chip peripheral modules such as the UART , timers, or Microwire/SPI interface. The I/O pin characteristics are fully programmable. Each pin can be configured to operate as a TRI-STATE output, push- pull output, weak pull-up input, or high-impedance input.

3.4 BUS INTERFACE UNIT

The Bus Interface Unit (BIU) controls access to internal/ex- ternal memory and I/O. It determines the configured param- eters for bus access (such as the number of wait states for memory access) and issues the appropriate bus signals for each requested access. The BIU uses a set of control registers to determine how many wait states and hold states are used when accessing Flash program memory and the I/O area. At start-up, the configuration registers are set for slowest possible memory access. To achieve fastest possible program execution, ap- propriate values must be programmed. These settings vary with the clock frequency and the type of off-chip device be- ing accessed.

3.5 INTERRUPT CONTROL UNIT (ICU)

The ICU receives interrupt requests from internal and exter- nal sources and generates interrupts to the CPU. An inter- rupt is an event that temporarily stops the normal flow of program execution and causes a separate interrupt handler to be executed. After the interrupt is serviced, CPU execu- tion continues with the next instruction in the program fol- lowing the point of interruption. Interrupts from the timers, UARTs, Microwire/SPI interface, and Multi-Input Wake-Up, are all maskable interrupts; they can be enabled or disabled by software. There are 47 maskable interrupts, assigned to 47 linear priority levels. The highest-priority interrupt is the Non-Maskable Interrupt (NMI ), which is generated by a signal received on the NMI input pin.

3.6 MULTI-INPUT WAKE-UP

The two Multi-Input Wake-Up (MIWU) modules can be used for two purposes: to provide inputs for waking up (exiting) from the Halt, Idle, or Power Save mode, and to provide gen- eral-purpose edge-triggered maskable interrupts to the lev- el-sensitive interrupt control unit (ICU) inputs. Each 16- channel module generates four programmable interrupts to the ICU, for a total of 8 ICU inputs generated from 32 MIWU inputs. Channels can be individually enabled or disabled, and programmed to respond to positive or negative edges. Obsolete

5 www.national.com CP3BT23

3.7 BLUETOOTH LLC

The integrated hardware Bluetooth Lower Link Controller (LLC) complies to the Bluetooth Specification Version 1.1 and integrates the following functions: ! 4.5K-byte dedicated Bluetooth Data RAM ! 1K-byte dedicated Bluetooth Sequencer RAM ! Support of all Bluetooth 1.1 packet types ! Support for fast frequency hopping of 1600 hops/s ! Access code correlation and slot timing recovery circuit ! Power Management Control Logic ! BlueRF-compatible interface (mode 2/3) to connect with National’s LMX5252 and other RF transceiver chips

3.8 CAN INTERFACE

Two CAN modules provide Full CAN 2.0B class, CAN serial bus interface for applications that require a high-speed (up to 1 Mbits per second) or a low-speed interface with CAN bus master capability. The data transfer between CAN and the CPU is established by 15 memory-mapped message buffers, which can be individually configured as receive or transmit buffers. An incoming message is filtered by two masks, one for the first 14 message buffers and another one for the 15th message buffer to provide a basic CAN path. A priority decoder allows any buffer to have the highest or low- est transmit priority. Remote transmission requests can be processed automatically by automatic reconfiguration to a receiver after transmission or by automated transmit sched- uling upon reception. In addition, a time stamp counter (16- bits wide) is provided to support real-time applications. The CAN modules are fast core bus peripherals, which al- low single-cycle byte or word read/write access. A set of di- agnostic features (such as loopback, listen only, and error identification) support the development with the CAN mod- ule and provide a sophisticated error management tool. The CAN receivers can trigger a wake-up condition out of the low-power modes through the Multi-Input Wake-Up module.

3.9 QUAD UART

Four UART modules support a wide range of programmable baud rates and data formats, parity generation, and several error detection schemes. The baud rate is generated on- chip, under software control. One UART channel supports hardware flow control, DMA, and USART capability (syn- chronous mode). The UARTs offer a wake-up condition from the low-power modes using the Multi-Input Wake-Up module.

3.10 ADVANCED AUDIO INTERFACE

The audio interface provides a serial synchronous, full-du- plex interface to CODECs and similar serial devices. Trans- mit and receive paths operate asynchronously with respect to each other. Each path uses three signals for communica- tion: shift clock, frame synchronization, and data. When the receiver and transmitter use separate shift clocks and frame sync signals, the interface operates in its asyn- chronous mode. Alternatively, the transmit and receive path can share the same shift clock and frame sync signals for synchronous mode operation.

3.11 CVSD/PCM CONVERSION MODULE

The CVSD/PCM module performs conversion between CVSD data and PCM data, in which the CVSD encoding is as defined in the Bluetooth specification and the PCM data can be 8-bit µ-Law, 8-bit A-Law, or 13-bit to 16-bit Linear. 3.12 12-BIT ANALOG TO DIGITAL CONVERTER This device contains an 8-channel, multiplexed input, suc- cessive approximation, 12-bit Analog-to-Digital Converter. It supports both Single Ended and Differential modes of oper- ation. The integrated 12-bit ADC provides the following features: ! 8-channel, multiplexed input ! 4 differential channels ! Single-ended and differential external filtering capability ! 12-bit resolution; 11-bit accuracy ! 15-microsecond conversion time ! Support for 4-wire touchscreen applications ! External start trigger ! Programmable start delay after start trigger ! Poll or interrupt on done The ADC is compatible with 4-wire resistive touchscreen applications and is intended to provide the resolution neces- sary to support handwriting recognition. Low-ohmic touch- screen drivers are provided internally on the ADC[3:0] pins. Pendown detection is also provided. The ADC provides several options for the voltage reference source. The positive reference can be ADVCC (internal), VREFP , ADC0, or ADC3. The negative reference can be ADVCC (internal), ADC1, or ADC2. Two specific analog channel selection modes are support- ed. These are as follows: ! Allow any specific channel to be selected at one time. The A/D Converter performs the specific conversion re- quested and stops. ! Allow any differential channel pair to be selected at one time. The A/D Converter performs the specific differential conversion requested and stops. In both Single-Ended and Differential modes, there is the capability to connect the analog multiplexer output and A/D converter input to external pins. This provides the ability to externally connect a common filter/signal conditioning cir- cuit for the A/D Converter.

3.13 RANDOM NUMBER GENERATOR

RNG peripheral for use in Trusted Computer Peripheral Ap- plications (TCPA) to improve the authenticity, integrity, and privacy of Internet-based communication and commerce. Obsolete

www.national.com 6 CP3BT23

3.14 MICROWIRE/SPI

The Microwire/SPI (MWSPI) interface module supports syn- chronous serial communications with other devices that conform to Microwire or Serial Peripheral Interface (SPI) specifications. It supports 8-bit and 16-bit data transfers. The Microwire interface allows several devices to communi- cate over a single system consisting of four wires: serial in, serial out, shift clock, and slave enable. At any given time, the Microwire interface operates as the master or a slave. The Microwire interface supports the full set of slave select for multi-slave implementation. In master mode, the shift clock is generated on-chip under software control. In slave mode, a wake-up out of a low- power mode may be triggered using the Multi-Input Wake- Up module. 3.15 ACCESS.BUS INTERFACE The ACCESS.bus interface module (ACB) is a two-wire se- rial interface compatible with the ACCESS.bus physical lay- er. It is also compatible with Intel’s System Management Bus (SMBus) and Philips’ I2C bus. The ACB module can be configured as a bus master or slave, and it can maintain bi- directional communications with both multiple master and slave devices. The ACCESS.bus receiver can trigger a wake-up condition out of the low-power modes through the Multi-Input Wake- Up module.

3.16 MULTI-FUNCTION TIMER

The Multi-Function Timer (MFT) module contains a pair of 16-bit timer/counter registers. Each timer/counter unit can be configured to operate in any of the following modes: Processor-Independent Pulse Width Modulation (PWM) mode: Generates pulses of a specified width and duty cycle and provides a general-purpose timer/ counter. Dual Input Capture mode: Measures the elapsed time between occurrences of external event and provides a general-purpose timer/counter. Dual Independent Timer mode: Generates system timing signals or counts occurrences of external events. Single Input Capture and Single Timer mode: Pro- vides one external event counter and one system tim- er.

3.17 TIMING AND WATCHDOG MODULE

The Timing and Watchdog Module (TWM) contains a Real- Time timer and a Watchdog unit. The Real-Time Clock Tim- ing function can be used to generate periodic real-time based system interrupts. The timer output is one of 16 in- puts to the Multi-Input Wake-Up module which can be used to exit from a power-saving mode. The Watchdog unit is de- signed to detect the application program getting stuck in an infinite loop resulting in loss of program control or “runaway” programs. When the watchdog triggers, it resets the device. The TWM is clocked by the low-speed System Clock.

3.18 VERSATILE TIMER UNIT

The Versatile Timer Unit (VTU) module contains four inde- pendent timer subsystems, each operating in either dual 8- bit PWM configuration, as a single 16-bit PWM timer, or a 16-bit counter with two input capture channels. Each of the four timer subsystems offer an 8-bit clock prescaler to ac- commodate a wide range of frequencies.

3.19 TRIPLE CLOCK AND RESET

The Triple Clock and Reset module generates a high-speed main System Clock from an external crystal network. It also provides the main system reset signal and a power-on reset function. This module generates a slow System Clock (32.768 kHz) from an optional external crystal network. The Slow Clock is used for operating the device in a low-power mode. The 32.768 kHz external crystal network is optional, because the low speed System Clock can be derived from the high- speed clock by a prescaler. Also, two independent clocks di- vided down from the high speed clock are available on out- put pins. The T riple Clock and Reset module provides the clock sig- nals required for the operation of the various CP3BT23 on- chip modules. From external crystal networks, it generates the Main Clock, which can be scaled up to 24 MHz from an external 12 MHz input clock, and a 32.768 kHz secondary System Clock. The 12 MHz external clock is primarily used as the reference frequency for the on-chip PLL. The clock for modules which require a fixed clock rate (e.g. the Blue- tooth LLC and the CVSD/PCM transcoder) is also generat- ed through prescalers from the 12 MHz clock. The PLL may be used to drive the high-speed System Clock through a prescaler. Alternatively, the high speed System Clock can be derived directly from the 12 MHz Main Clock. In addition, this module generates the device reset by using reset input signals coming from an external reset and vari- ous on-chip modules.

3.20 POWER MANAGEMENT

The Power Management Module (PMM) improves the effi- ciency of the device by changing the operating mode and power consumption to match the required level of activity. The device can operate in any of four power modes: — Active: The device operates at full speed using the high-frequency clock. All device functions are fully op- erational. — Power Save: The device operates at reduced speed using the Slow Clock. The CPU and some modules can continue to operate at this low speed. Idle: The device is inactive except for the Power Man- agement Module and Timing and Watchdog Module, which continue to operate using the Slow Clock. Halt: The device is inactive but still retains its internal state (RAM and register contents). Obsolete

7 www.national.com CP3BT23

3.21 DMA CONTROLLER

The Direct Memory Access Controller (DMAC) can speed up data transfer between memory and I/O devices or be- tween two memories, relative to data transfers performed di- rectly by the CPU. A method called cycle-stealing allows the CPU and the DMAC to share the CPU bus efficiently. The DMAC implements four independent DMA channels. DMA requests from a primary and a secondary source are recog- nized for each DMA channel, as well as a software DMA re- quest issued directly by the CPU. Table 1 shows the DMA channel assignment on the CP3BT23 architecture. The fol- lowing on-chip modules can assert a DMA request to the DMAC:  CR16C (Software DMA request)  USART  Advanced Audio Interface  CVSD/PCM Converter Table 1 shows how the four DMA channels are assigned to the modules listed above. Table 1 DMA Channel Assignment The interface can handle data words of either 8- or 16-bit length and data frames can consist of up to four slots. In the normal mode of operation, the interface only transfers one word at a periodic rate. In the network mode, the inter- face transfers multiple words at a periodic rate. The periodic rate is also called a data frame and each word within one frame is called a slot. The beginning of each new data frame is marked by the frame sync signal.

3.22 SERIAL DEBUG INTERFACE

The Serial Debug Interface module (SDI module) provides a JTAG-based serial link to an external debugger, for exam- ple running on a PC. In addition, the SDI module integrates an on-chip debug module, which allows the user to set up to eight hardware breakpoints on instruction execution and data transfer. The SDI module can act as a CPU bus master to access all memory mapped resources, such as RAM and peripherals. Therefore it also allows for fast program code download into the on-chip Flash program memory using the JTAG interface. Note: The SDI module may assert Freeze mode to gather information, which may cause periodic fluctuations in re- sponse (bus availability, interrupt latency, etc.). Anomalous behavior often may be traced to SDI activity.

3.23 DEVELOPMENT SUPPORT

In addition to providing the features needed for the next gen- eration of embedded Bluetooth products, the CP3BT23 de- vices are backed up by the software resources designers need for rapid product development, including an operating system, Bluetooth protocol stack implementation, peripher- al drivers, reference designs, and an integrated develop- ment environment. Combined with National’s LMX5251 Bluetooth radio transceiver, the CP3BT23 devices provide a total Bluetooth system solution. National Semiconductor offers a complete and industry- proven application development environment for CP3BT23 applications, including the IAR Embedded Workbench, iSYSTEM winIDEA and iC3000 Active Emulator, Bluetooth Development Board, Bluetooth Protocol Stack, and Applica- tion Software. See your National Semiconductor sales rep- resentative for current information on availability and features of emulation equipment and evaluation boards. Channel Primary/ Secondary Peripheral Transaction Primary Reserved Read/Write Secondary UART0 Read Primary UART0 Write Secondary Unused N/A Primary AAI Read Secondary CVSD/PCM Read Primary AAI Write Secondary CVSD/PCM Write Obsolete

4.0 Signal Descriptions

Figure 1. CP3BT23 Device SIgnals nals for the LQFP-144 package.

9 www.national.com CP3BT23 Table 2 CP3BT23 LQFP-128 Signal Descriptions Name Pins I/O Primary Function Alternate Name Alternate Function X1CKI 1 Input 12 MHz Oscillator Input BBCLK BB reference clock for the RF Interface X1CKO 1 Output 12 MHz Oscillator Output None None X2CKI 1 Input 32 kHz Oscillator Input None None X2CKO 1 Output 32 kHz Oscillator Output None None RESET 1 Input Chip general reset None None ENV0 1 I/O Special mode select input with internal pull-up during reset PLLCLK PLL Clock Output ENV1 1 I/O Special mode select input with internal pull-up during reset CPUCLK CPU Clock Output ENV2 1 I/O Special mode select input with internal pull-up during reset SLOWCLK Slow Clock Output TMS 1 Input JTAG Test Mode Select (with internal weak pull-up) None None TCK 1 Input JTAG Test Clock Input (with internal weak pull-up) None None TDI 1 Input JT AG T est Data Input (with internal weak pull-up) None None TDO 1 Output JTAG Test Data Output None None RDY

1 Output NEXUS Ready Output None None

VCC 6 Input 2.5V Core Logic Power Supply None None GND 6 Input Core Ground None None IOVCC 16 Input 2.5 –3.3V I/O Power Supply None None IOGND 15 Input I/O Ground None None AVCC 1 Input PLL Analog Power Supply None None AGND 1 Input PLL Analog Ground None None ADVCC 1 Input ADC Analog Power Supply None None ADGND 1 Input ADC Analog Ground None None RFDATA 1 I/O Bluetooth RX/TX Data Pin None None SCL 1 I/O ACCESS.bus Clock None None SDA 1 I/O ACCESS.bus Serial Data None None ADC0 1 I/O ADC Input Channel 0 TSX+ T ouchscreen X+ contact ADC1 1 I/O ADC Input Channel 1 TSY+ T ouchscreen Y+ contact ADC2 1 I/O ADC Input Channel 2 TSX- T ouchscreen X- contact ADC3 1 I/O ADC Input Channel 3 TSY - T ouchscreen Y - contact ADC4 1 I/O ADC Input Channel 4 MUXOUT0 Analog Multiplexer Output 0 ADC5 1 I/O ADC Input Channel 5 MUXOUT1 Analog Multiplexer Output 1 ADC6 1 Input ADC Input Channel 6 None None Obsolete

www.national.com 10 CP3BT23ADC7 1 Input ADC Input Channel 7 ADCIN ADC Input (in MUX mode) VREFP 1 Input ADC Positive Voltage Reference None None PB[7:0] 8 I/O Generic I/O None None PC[7:0] 8 I/O Generic I/O None None PE0 1 I/O Generic I/O RXD0 UART Channel 0 Receive Data Input PE1 1 I/O Generic I/O TXD0 UART Channel 0 Transmit Data Output PE2 1 I/O Generic I/O RTS UART Channel 0 Ready-T o-Send Output PE3 1 I/O Generic I/O CTS UART Channel 0 Clear-To-Send Input PE4 1 I/O Generic I/O CKX UART Channel 0 Clock Input TB Multi Function Timer Port B PE5 1 I/O Generic I/O SRFS AAI Receive Frame Sync NMI Non-Maskable Interrupt Input PE6 1 I/O Generic I/O CAN1RX UART Channel 0 Ready-T o-Send Output PE7 1 I/O Generic I/O CAN1TX UART Channel 0 Clear-To-Send Input PF0 1 I/O Generic I/O MSK SPI Shift Clock TIO1 Versatile Timer Channel 1 PF1 1 I/O Generic I/O MDIDO SPI Master In Slave Out TIO2 Versatile Timer Channel 2 PF2 1 I/O Generic I/O MDODI SPI Master Out Slave In TIO3 Versatile Timer Channel 3 PF3 1 I/O Generic I/O MWCS SPI Slave Select Input TIO4 Versatile Timer Channel 4 PF4 1 I/O Generic I/O SCK AAI Clock TIO5 Versatile Timer Channel 5 PF5 1 I/O Generic I/O SFS AAI Frame Synchronization TIO6 Versatile Timer Channel 6 PF6 1 I/O Generic I/O STD AAI Transmit Data Output TIO7 Versatile Timer Channel 7 PF7 1 I/O Generic I/O SRD AAI Receive Data Input TIO8 Versatile Timer Channel 8 PG0 1 I/O Generic I/O RFSYNC BT AC Correlation/TX Enable Output PG1 1 I/O Generic I/O RFCE BT RF Chip Enable Output PG2 1 I/O Generic I/O BTSEQ1 Bluetooth Sequencer Status SRCLK AAI Receive Clock PG3 1 I/O Generic I/O SCLK BT Serial I/F Shift Clock Output PG4 1 I/O Generic I/O SDAT BT Serial I/F Data PG5 1 I/O Generic I/O SLE BT Serial I/F Load Enable Output Name Pins I/O Primary Function Alternate Name Alternate Function Obsolete

11 www.national.com CP3BT23 PG6 1 I/O Generic I/O WUI10 Multi-Input Wake-Up Channel 10 BTSEQ2 Bluetooth Sequencer Status PG7 1 I/O Generic I/O TA Multi Function Timer Port A BTSEQ3 Bluetooth Sequencer Status PH0 1 I/O Generic I/O RXD1 UART Channel 1 Receive Data Input WUI11 Multi-Input Wake-Up Channel 11 PH1 1 I/O Generic I/O TXD1 UART Channel 1 Transmit Data Output WUI12 Multi-Input Wake-Up Channel 12 PH2 1 I/O Generic I/O RXD2 UART Channel 2 Receive Data Input WUI13 Multi-Input Wake-Up Channel 13 PH3 1 I/O Generic I/O TXD2 UART Channel 2 Transmit Data Output WUI14 Multi-Input Wake-Up Channel 14 PH4 1 I/O Generic I/O RXD3 UART Channel 3 Receive Data Input WUI15 Multi-Input Wake-Up Channel 15 PH5 1 I/O Generic I/O TXD3 UART Channel 3 Transmit Data Output WUI16 Multi-Input Wake-Up Channel 16 PH6 1 I/O Generic I/O CAN0RX CAN Receive Input WUI17 Multi-Input Wake-Up Channel 17 PH7 1 I/O Generic I/O CAN0TX CAN Transmit Output PJ0 1 I/O Generic I/O WUI18 Multi-Input Wake-Up Channel 18 PJ1 1 I/O Generic I/O WUI19 Multi-Input Wake-Up Channel 19 PJ2 1 I/O Generic I/O WUI20 Multi-Input Wake-Up Channel 20 PJ3 1 I/O Generic I/O WUI21 Multi-Input Wake-Up Channel 21 PJ4 1 I/O Generic I/O WUI22 Multi-Input Wake-Up Channel 22 PJ5 1 I/O Generic I/O WUI23 Multi-Input Wake-Up Channel 23 PJ6 1 I/O Generic I/O WUI24 Multi-Input Wake-Up Channel 24 PJ7 1 I/O Generic I/O ASYNC Start convert signal to ADC WUI9 Multi-Input Wake-Up Channel 9 Name Pins I/O Primary Function Alternate Name Alternate Function Obsolete

www.national.com 12 CP3BT23 Table 3 CP3BT23 LQFP-144 Signal Descriptions Name Pins I/O Primary Function Alternate Name Alternate Function X1CKI 1 Input 12 MHz Oscillator Input BBCLK BB reference clock for the RF Interface X1CKO 1 Output 12 MHz Oscillator Output None None X2CKI 1 Input 32 kHz Oscillator Input None None X2CKO 1 Output 32 kHz Oscillator Output None None RESET 1 Input Chip general reset None None ENV0 1 I/O Special mode select input with internal pull-up during reset PLLCLK PLL Clock Output ENV1 1 I/O Special mode select input with internal pull-up during reset CPUCLK CPU Clock Output ENV2 1 I/O Special mode select input with internal pull-up during reset SLOWCLK Slow Clock Output TMS 1 Input JTAG Test Mode Select (with internal weak pull-up) None None TCK 1 Input JTAG Test Clock Input (with internal weak pull-up) None None TDI 1 Input JTAG Test Data Input (with internal weak pull-up) None None TDO 1 Output JTAG Test Data Output None None RDY VCC 6 Input 2.5V Core Logic Power Supply None None GND 6 Input Core Ground None None IOVCC 10 Input 2.5 –3.3V I/O Power Supply None None IOGND 11 Input I/O Ground None None AVCC 1 Input PLL Analog Power Supply None None AGND 1 Input PLL Analog Ground None None ADVCC 1 Input ADC Analog Power Supply None None ADGND 1 Input ADC Analog Ground None None RFDATA 1 I/O Bluetooth RX/TX Data Pin None None SCL 1 I/O ACCESS.bus Clock None None SDA 1 I/O ACCESS.bus Serial Data None None ADC0 1 I/O ADC Input Channel 0 TSX+ T ouchscreen X+ contact ADC1 1 I/O ADC Input Channel 1 TSY+ T ouchscreen Y+ contact ADC2 1 I/O ADC Input Channel 2 TSX- T ouchscreen X- contact ADC3 1 I/O ADC Input Channel 3 TSY - T ouchscreen Y - contact ADC4 1 I/O ADC Input Channel 4 MUXOUT0 Analog Multiplexer Output 0 ADC5 1 I/O ADC Input Channel 5 MUXOUT1 Analog Multiplexer Output 1 ADC6 1 Input ADC Input Channel 6 None None Obsolete

13 www.national.com CP3BT23 ADC7 1 Input ADC Input Channel 7 ADCIN ADC Input (in MUX mode) VREFP 1 Input ADC Positive Voltage Reference None None PB[7:0] 8 I/O Generic I/O D[7:0] External Data Bus Bits 0 to 7 PC[7:0] 8 I/O Generic I/O D[8:15] External Data Bus Bits 8 to 15 A[22:0] 23 Output External Address Bus Bits 0 to 22 None None SEL0 1 Output Chip Select for Zone 0 None None SEL1 1 Output Chip Select for Zone 1 None None SEL2 1 Output Chip Select for Zone 2 None None SELIO 1 Output Chip Select for I/O Zone None None WR0 1 Output External Memory Write Low Byte None None WR1 1 Output External Memory Write High Byte None None RD 1 Output External Memory Read None None PE0 1 I/O Generic I/O RXD0 UART0 Receive Data Input PE1 1 I/O Generic I/O TXD0 UART0 Transmit Data Output PE2 1 I/O Generic I/O RTS UART0 Ready-To-Send Output PE3 1 I/O Generic I/O CTS UART0 Clear-To-Send Input PE4 1 I/O Generic I/O CKX UART0 Clock Input TB Multi Function Timer Port B PE5 1 I/O Generic I/O SRFS AAI Receive Frame Sync NMI Non-Maskable Interrupt Input PE6 1 I/O Generic I/O CAN1RX UART Channel 0 Ready-T o-Send Output PE7 1 I/O Generic I/O CAN1TX UART Channel 0 Clear-To-Send Input PF0 1 I/O Generic I/O MSK SPI Shift Clock TIO1 Versatile Timer Channel 1 PF1 1 I/O Generic I/O MDIDO SPI Master In Slave Out TIO2 Versatile Timer Channel 2 PF2 1 I/O Generic I/O MDODI SPI Master Out Slave In TIO3 Versatile Timer Channel 3 PF3 1 I/O Generic I/O MWCS SPI Slave Select Input TIO4 Versatile Timer Channel 4 PF4 1 I/O Generic I/O SCK AAI Clock TIO5 Versatile Timer Channel 5 PF5 1 I/O Generic I/O SFS AAI Frame Synchronization TIO6 Versatile Timer Channel 6 PF6 1 I/O Generic I/O STD AAI Transmit Data Output TIO7 Versatile Timer Channel 7 Name Pins I/O Primary Function Alternate Name Alternate Function Obsolete

www.national.com 14 CP3BT23 PF7 1 I/O Generic I/O SRD AAI Receive Data Input TIO8 Versatile Timer Channel 8 PG0 1 I/O Generic I/O RFSYNC BT AC Correlation/TX Enable Output PG1 1 I/O Generic I/O RFCE BT RF Chip Enable Output PG2 1 I/O Generic I/O BTSEQ1 Bluetooth Sequencer Status SRCLK AAI Receive Clock PG3 1 I/O Generic I/O SCLK BT Serial I/F Shift Clock Output PG4 1 I/O Generic I/O SDAT BT Serial I/F Data PG5 1 I/O Generic I/O SLE BT Serial I/F Load Enable Output PG6 1 I/O Generic I/O WUI10 Multi-Input Wake-Up Channel 10 BTSEQ2 Bluetooth Sequencer Status PG7 1 I/O Generic I/O T A Multi Function Timer Port A BTSEQ3 Bluetooth Sequencer Status PH0 1 I/O Generic I/O RXD1 UART Channel 1 Receive Data Input WUI11 Multi-Input Wake-Up Channel 11 PH1 1 I/O Generic I/O TXD1 UART Channel 1 Transmit Data Output WUI12 Multi-Input Wake-Up Channel 12 PH2 1 I/O Generic I/O RXD2 UART Channel 2 Receive Data Input WUI13 Multi-Input Wake-Up Channel 13 PH3 1 I/O Generic I/O TXD2 UART Channel 2 Transmit Data Output WUI14 Multi-Input Wake-Up Channel 14 PH4 1 I/O Generic I/O RXD3 UART Channel 3 Receive Data Input WUI15 Multi-Input Wake-Up Channel 15 PH5 1 I/O Generic I/O TXD3 UART Channel 3 Transmit Data Output WUI16 Multi-Input Wake-Up Channel 16 PH6 1 I/O Generic I/O CAN0RX CAN Receive Input WUI17 Multi-Input Wake-Up Channel 17 PH7 1 I/O Generic I/O CAN0TX CAN Transmit Output PJ0 1 I/O Generic I/O WUI18 Multi-Input Wake-Up Channel 18 PJ7 1 I/O Generic I/O ASYNC Start Convert Signal to ADC WUI9 Multi-Input Wake-Up Channel 9 Name Pins I/O Primary Function Alternate Name Alternate Function Obsolete

5.0 CPU Architecture

Semiconductor web site (http://www.nsc.com). R12, R13, RA, SP , ISP and USP registers are 32 bits wide. Figure 2. CPU Registers

5.1 GENERAL-PURPOSE REGISTERS

of the earlier CR16A/B CPU cores: (R1,R0), (R2,R1) ... dresses greater than 16 bits. addresses used in the index addressing mode. used. The upper word is not referenced or modified.

5.2 DEDICATED ADDRESS REGISTERS

5.2.1 Program Counter (PC) Register

the (R1,R0) general-purpose register pair.

5.2.2 Interrupt Stack Pointer (ISP)

5.2.3 User Stack Pointer (USP)

access, an IAD trap is taken.

www.national.com 16 CP3BT23

5.2.4 Interrupt Base Register (INTBASE)

The INTBASE register holds the address of the dispatch ta- ble for exceptions. The dispatch table can be located any- where in the CPU address space. When loading the INTBASE register, bits 31 to 24 and bit 0 must written with 0.

5.3 PROCESSOR STATUS REGISTER (PSR)

The PSR provides state information and controls operating modes for the CPU. The format of the PSR is shown below. C The Carry bit indicates whether a carry or bor- row occurred after addition or subtraction. – No carry or borrow occurred. 1 – Carry or borrow occurred. T The Trace bit enables execution tracing, in which a Trace trap (TRC) is taken after every instruction. Tracing is automatically disabled during the execution of an exception handler. – Tracing disabled. 1 – Tracing enabled. L The Low bit indicates the result of the last comparison operation, with the operands in- terpreted as unsigned integers. – Second operand greater than or equal to first operand. 1 – Second operand less than first operand. U The User Mode bit controls whether the CPU is in user or supervisor mode. In supervisor mode, the SP register is used for stack opera- tions. In user mode, the USP register is used instead. User mode is entered by executing the Jump USR instruction. When an exception is taken, the exception handler automatically begins execution in supervisor mode. The USP register is accessible using the Load Processor Register (LPR/LPRD) instruction in supervisor mode. In user mode, an attempt to access the USP register generates a UND trap. – CPU is executing in supervisor mode. 1 – CPU is executing in user mode. F The Flag bit is a general condition flag for sig- nalling exception conditions or distinguishing the results of an instruction, among other thing uses. For example, integer arithmetic in- structions use the F bit to indicate an overflow condition after an addition or subtraction oper- ation. Z The Zero bit is used by comparison opera- tions. In a comparison of integers, the Z bit is set if the two operands are equal. If the oper- ands are unequal, the Z bit is cleared. – Source and destination operands un- equal. 1 – Source and destination operands equal. N The Negative bit indicates the result of the last comparison operation, with the operands in- terpreted as signed integers. – Second operand greater than or equal to first operand. – Second operand less than first operand. E The Local Maskable Interrupt Enable bit en- ables or disables maskable interrupts. If this bit and the Global Maskable Interrupt Enable (I) bit are both set, all interrupts are enabled. If either of these bits is clear, only the non- maskable interrupt is enabled. The E bit is set by the Enable Interrupts (EI) instruction and cleared by the Disable Interrupts (DI) instruc- tion. – Maskable interrupts disabled. 1 – Maskable interrupts enabled. P The Trace Trap Pending bit is used together with the Trace (T) bit to prevent a Trace (TRC) trap from occurring more than once for one in- struction. At the beginning of the execution of an instruction, the state of the T bit is copied into the P bit. If the P bit remains set at the end of the instruction execution, the TRC trap is taken. – No trace trap pending. 1 – Trace trap pending. I The Global Maskable Interrupt Enable bit is used to enable or disable maskable interrupts. If this bit and the Local Maskable Interrupt En- able (E) bit are both set, all maskable inter- rupts are taken. If either bit is clear, only the non-maskable interrupt is taken. Unlike the E bit, the I bit is automatically cleared when an interrupt occurs and automatically set upon completion of an interrupt handler. – Maskable interrupts disabled. 1 – Maskable interrupts enabled. Bits Z, C, L, N, and F of the PSR are referenced from as- sembly language by the condition code in conditional branch instructions. A conditional branch instruction may cause a branch in program execution, based on the value of one or more of these PSR bits. For example, one of the Bcond instructions, BEQ (Branch EQual), causes a branch if the PSR.Z bit is set. On reset, bits 0 through 11 of the PSR are cleared, except for the PSR.E bit, which is set. On warm reset, the values of each bit before reset are copied into the R2 general-pur- pose register. Bits 4 and 8 of the PSR have a constant value of 0. Bits 12 through 15 are reserved. In general, status bits are modified only by specific instructions. Otherwise, status bits maintain their values throughout instructions which do not implicitly affect them. 15 12 11 10 9 8 7 6 5 4 3 2 1 0 Reserved I P E 0 N Z F 0 U L T C Obsolete

17 www.national.com CP3BT23

5.4 CONFIGURATION REGISTER (CFG)

The CFG register is used to enable or disable various oper- ating modes and to control optional on-chip caches. Be- cause the CP3BT23 does not have cache memory, the cache control bits in the CFG register are reserved. All CFG bits are cleared on reset. ED The Extended Dispatch bit selects whether the size of an entry in the interrupt dispatch ta- ble (IDT) is 16 or 32 bits. Each entry holds the address of the appropriate exception handler. When the IDT has 16-bit entries, and all ex- ception handlers must reside in the first 128K of the address space. The location of the IDT is held in the INTBASE register, which is not affected by the state of the ED bit. – Interrupt dispatch table has 16-bit entries. 1 – Interrupt dispatch table has 32-bit entries. SR The Short Register bit enables a compatibility mode for the CR16B large model. In the CR16C core, registers R12, R13, and RA are extended to 32 bits. In the CR16B large mod- el, only the lower 16 bits of these registers are used, and these “short registers” are paired together for 32-bit operations. In this mode, the (RA, R13) register pair is used as the ex- tended RA register, and address displace- ments relative to a single register are supported with offsets of 0 and 14 bits in place of the index addressing with these displace- ments. – 32-bit registers are used. 1 – 16-bit registers are used (CR16B mode). 15 10 9 8 7 6 5 2 1 0 Reserved SR ED 0 0 Reserved 0 0 Obsolete

www.national.com 18 CP3BT23

5.5 ADDRESSING MODES

The CR16C CPU core implements a load/store architec- ture, in which arithmetic and logical instructions operate on register operands. Memory operands are made accessible in registers using load and store instructions. For efficient implementation of I/O-intensive embedded applications, the architecture also provides a set of bit operations that oper- ate on memory operands. The load and store instructions support these addressing modes: register/pair, immediate, relative, absolute, and in- dex addressing. When register pairs are used, the lower bits are in the lower index register and the upper bits are in the higher index register. When the CFG.SR bit is clear, the 32- bit registers R12, R13, RA, and SP are also treated as reg- ister pairs. References to register pairs in assembly language use pa- rentheses. With a register pair, the lower numbered register pair must be on the right. For example, jump (r5, r4) load $4(r4,r3), (r6,r5) load $5(r12), (r13) The instruction set supports the following addressing modes: For additional information on the addressing modes, see the CompactRISC CR16C Programmer's Reference Manual. Register/Pair Mode In register/pair mode, the operand is held in a general-purpose register, or in a gen- eral-purpose register pair. For example, the following instruction adds the con- tents of the low byte of register r1 to the contents of the low byte of r2, and places the result in the low byte register r2. The high byte of register r2 is not modified. ADDB R1, R2 Immediate Mode In immediate mode, the operand is a con- stant value which is encoded in the in- struction. For example, the following instruction multiplies the value of r4 by 4 and places the result in r4. MULW $4, R4 Relative Mode In relative mode, the operand is ad- dressed using a relative value (displace- ment) encoded in the instruction. This displacement is relative to the current Program Counter (PC), a general-pur- pose register, or a register pair. In branch instructions, the displacement is always relative to the current value of the PC Register. For example, the follow- ing instruction causes an unconditional branch to an address 10 ahead of the current PC. BR *+10 In another example, the operand resides in memory. Its address is obtained by adding a displacement encoded in the in- struction to the contents of register r5. The address calculation does not modify the contents of register r5. LOADW 12(R5), R6 The following example calculates the ad- dress of a source operand by adding a displacement of 4 to the contents of a register pair (r5, r4) and loads this oper- and into the register pair (r7, r6). r7 re- ceives the high word of the operand, and r6 receives the low word. LOADD 4(r5, r4), (r7, r6) Index Mode In index mode, the operand address is calculated with a base address held in ei- ther R12 or R13. The CFG.SR bit must be clear to use this mode. ! For relative mode operands, the mem- ory address is calculated by adding the value of a register pair and a dis- placement to the base address. The displacement can be a 14 or 20-bit un- signed value, which is encoded in the instruction. ! For absolute mode operands, the memory address is calculated by add- ing a 20-bit absolute address encoded in the instruction to the base address. In the following example, the operand ad- dress is the sum of the displacement 4, the contents of the register pair (r5,r4), and the base address held in register r12. The word at this address is loaded into register r6. LOADW [r12]4(r5, r4), r6 Absolute Mode In absolute mode, the operand is located in memory, and its address is encoded in the instruction (normally 20 or 24 bits). For example, the following instruction loads the byte at address 4000 into the lower 8 bits of register r6. LOADB 4000, r6 Obsolete

19 www.national.com CP3BT23

5.6 STACKS

A stack is a last-in, first-out data structure for dynamic stor- age of data and addresses. A stack consists of a block of memory used to hold the data and a pointer to the top of the stack. As more data is pushed onto a stack, the stack grows downward in memory. The CR16C supports two types of stacks: the interrupt stack and program stacks.

5.6.1 Interrupt Stack

The processor uses the interrupt stack to save and restore the program state during the exception handling. Hardware automatically pushes this data onto the interrupt stack be- fore entering an exception handler. When the exception handler returns, hardware restores the processor state with data popped from the interrupt stack. The interrupt stack pointer is held in the ISP register.

5.6.2 Program Stack

The program stack is normally used by software to save and restore register values on subroutine entry and exit, hold lo- cal and temporary variables, and hold parameters passed between the calling routine and the subroutine. The only hardware mechanisms which operate on the program stack are the PUSH, POP , and POPRET instructions.

5.6.3 User and Supervisor Stack Pointers

To support multitasking operating systems, support is pro- vided for two program stack pointers: a user stack pointer and a supervisor stack pointer. When the PSR.U bit is clear, the SP register is used for all program stack operations. This is the default mode when the user/supervisor protection mechanism is not used, and it is the supervisor mode when protection is used. When the PSR.U bit is set, the processor is in user mode, and the USP register is used as the program stack pointer. User mode can only be entered using the JUSR instruction, which performs a jump and sets the PSR.U bit. User mode is exited when an exception is taken and re-entered when the exception handler returns. In user mode, the LPRD in- struction cannot be used to change the state of processor registers (such as the PSR).

5.7 INSTRUCTION SET

Table 4 lists the operand specifiers for the instruction set, and T able 5 is a summary of all instructions. For each in- struction, the table shows the mnemonic and a brief de- scription of the operation performed. In the mnemonic column, the lower-case letter “i” is used to indicate the type of integer that the instruction operates on, either “B” for byte or “W ” for word. For example, the notation ADDi for the “add” instruction means that there are two forms of this instruction, ADDB and ADDW, which operate on bytes and words, respectively. Similarly, the lower-case string “cond” is used to indicate the type of condition tested by the instruction. For example, the notation Jcond represents a class of conditional jump in- structions: JEQ for Jump on Equal, JNE for Jump on Not Equal, etc. For detailed information on all instructions, see the CompactRISC CR16C Programmer's Reference Manu- al. Table 4 Key to Operand Specifiers Operand Specifier Description abs Absolute address disp Displacement (numeric suffix indicates number of bits) imm Immediate operand (numeric suf- fix indicates number of bits) Iposition Bit position in memory Rbase Base register (relative mode) Rdest Destination register Rindex Index register RPbase, RPbasex Base register pair (relative mode) RPdest Destination register pair RPlink Link register pair Rposition Bit position in register Rproc 16-bit processor register Rprocd 32-bit processor register RPsrc Source register pair RPtarget Target register pair Rsrc, Rsrc1, Rsrc2 Source register Obsolete

www.national.com 20 CP3BT23 Table 5 Instruction Set Summary Mnemonic Operands Description MOVi Rsrc/imm, Rdest Move MOVXB Rsrc, Rdest Move with sign extension MOVZB Rsrc, Rdest Move with zero extension MOVXW Rsrc, RPdest Move with sign extension MOVZW Rsrc, RPdest Move with zero extension MOVD imm, RPdest Move immediate to register-pair RPsrc, RPdest Move between register-pairs ADD[U]i Rsrc/imm, Rdest Add ADDCi Rsrc/imm, Rdest Add with carry ADDD RPsrc/imm, RPdest Add with RP or immediate. MACQWa Rsrc1, Rsrc2, RPdest Multiply signed Q15: RPdest := RPdest + (Rsrc1 × Rsrc2) MACSWa Rsrc1, Rsrc2, RPdest Multiply signed and add result: RPdest := RPdest + (Rsrc1 × Rsrc2) MACUWa Rsrc1, Rsrc2, RPdest Multiply unsigned and add result: RPdest := RPdest + (Rsrc1 × Rsrc2) MULi Rsrc/imm, Rdest Multiply: Rdest(8) := Rdest(8) × Rsrc(8)/imm Rdest(16) := Rdest(16) × Rsrc(16)/imm MULSB Rsrc, Rdest Multiply: Rdest(16) := Rdest(8) × Rsrc(8) MULSW Rsrc, RPdest Multiply: RPdest := RPdest(16) × Rsrc(16) MULUW Rsrc, RPdest Multiply: RPdest := RPdest(16) × Rsrc(16); SUBi Rsrc/imm, Rdest Subtract: (Rdest := Rdest - Rsrc/imm) SUBD RPsrc/imm, RPdest Subtract: (RPdest := RPdest - RPsrc/imm) SUBCi Rsrc/imm, Rdest Subtract with carry: (Rdest := Rdest - Rsrc/imm) CMPi Rsrc/imm, Rdest Compare Rdest - Rsrc/imm CMPD RPsrc/imm, RPdest Compare RPdest - RPsrc/imm BEQ0i Rsrc, disp Compare Rsrc to 0 and branch if EQUAL BNE0i Rsrc, disp Compare Rsrc to 0 and branch if NOT EQUAL ANDi Rsrc/imm, Rdest Logical AND: Rdest := Rdest & Rsrc/imm ANDD RPsrc/imm, RPdest Logical AND: RPdest := RPsrc & RPsrc/imm ORi Rsrc/imm, Rdest Logical OR: Rdest := Rdest | Rsrc/imm ORD RPsrc/imm, RPdest Logical OR: Rdest := RPdest | RPsrc/imm Scond Rdest Save condition code as boolean XORi Rsrc/imm, Rdest Logical exclusive OR: Rdest := Rdest ^ Rsrc/imm XORD RPsrc/imm, RPdest Logical exclusive OR: Rdest := RPdest ^ RPsrc/imm ASHUi Rsrc/imm, Rdest Arithmetic left/right shift Obsolete

21 www.national.com CP3BT23 ASHUD Rsrc/imm, RPdest Arithmetic left/right shift LSHi Rsrc/imm, Rdest Logical left/right shift LSHD Rsrc/imm, RPdest Logical left/right shift SBITi Iposition, disp(Rbase) Set a bit in memory (Because this instruction treats the destination as a read- modify-write operand, it not be used to set bits in write- only registers.) Iposition, disp(RPbase) Iposition, (Rindex)disp(RPbasex) Iposition, abs Iposition, (Rindex)abs CBITi Iposition, disp(Rbase) Clear a bit in memory Iposition, disp(RPbase) Iposition, (Rindex)disp(RPbasex) Iposition, abs Iposition, (Rindex)abs TBIT TBITi Rposition/imm, Rsrc Test a bit in a register T est a bit in memoryIposition, disp(Rbase) Iposition, disp(RPbase) Iposition, (Rindex)disp(RPbasex) Iposition, abs Iposition, (Rindex)abs LPR Rsrc, Rproc Load processor register LPRD RPsrc, Rprocd Load double processor register SPR Rproc, Rdest Store processor register SPRD Rprocd, RPdest Store 32-bit processor register Bcond disp9 Conditional branch disp17 disp24 BAL RPlink, disp24 Branch and link BR disp9 Branch disp17 disp24 EXCP vector T rap (vector) Jcond RPtarget Conditional Jump to a large address JAL RA, RPtarget, Jump and link to a large address RPlink, RPtarget JUMP RPtarget Jump JUSR RPtarget Jump and set PSR.U Table 5 Instruction Set Summary Mnemonic Operands Description Obsolete

www.national.com 22 CP3BT23RETX Return from exception PUSH imm, Rsrc, RA Push “imm” number of registers on user stack, starting with Rsrc and possibly including RA POP imm, Rdest, RA Restore “imm” number of registers from user stack, starting with Rdest and possibly including RA POPRET imm, Rdest, RA Restore registers (similar to POP) and JUMP RA LOADi disp(Rbase), Rdest Load (register relative) abs, Rdest Load (absolute) (Rindex)abs, Rdest Load (absolute index relative) (Rindex)disp(RPbasex), Rdest Load (register relative index) disp(RPbase), Rdest Load (register pair relative) LOADD disp(Rbase), Rdest Load (register relative) abs, Rdest Load (absolute) (Rindex)abs, Rdest Load (absolute index relative) (Rindex)disp(RPbasex), Rdest Load (register pair relative index) disp(RPbase), Rdest Load (register pair relative) STORi Rsrc, disp(Rbase) Store (register relative) Rsrc, disp(RPbase) Store (register pair relative) Rsrc, abs Store (absolute) Rsrc, (Rindex)disp(RPbasex) Store (register pair relative index) Rsrc, (Rindex)abs Store (absolute index) STORD RPsrc, disp(Rbase) Store (register relative) RPsrc, disp(RPbase) Store (register pair relative) RPsrc, abs Store (absolute) RPsrc, (Rindex)disp(RPbasex) Store (register pair index relative) RPsrc, (Rindex)abs Store (absolute index relative) STOR IMM imm4, disp(Rbase) Store unsigned 4-bit immediate value extended to operand length in memoryimm4, disp(RPbase) imm4, (Rindex)disp(RPbasex) imm4, abs imm4, (Rindex)abs LOADM imm3 Load 1 to 8 registers (R2-R5, R8-R11) from memory starting at (R0) LOADMP imm3 Load 1 to 8 registers (R2-R5, R8-R11) from memory starting at (R1, R0) STORM STORM imm3 Store 1 to 8 registers (R2-R5, R8-R11) to memory starting at (R2) Table 5 Instruction Set Summary Mnemonic Operands Description Obsolete

23 www.national.com CP3BT23 STORMP imm3 Store 1 to 8 registers (R2-R5, R8-R11) to memory starting at (R7,R6) DI Disable maskable interrupts EI Enable maskable interrupts EIWAIT Enable maskable interrupts and wait for interrupt NOP No operation WAIT Wait for interrupt Table 5 Instruction Set Summary Mnemonic Operands Description Obsolete

www.national.com 24 CP3BT23

6.0 Memory

The CP3BT23 supports a uniform 16M-byte linear address space. Table 6 lists the types of memory and peripherals that occupy this memory space. Unlisted address ranges are reserved and must not be read or written. The BIU zones are regions of the address space that share the same control bits in the Bus Interface Unit (BIU). Table 6 CP3BT23 Memory Map

6.1 OPERATING ENVIRONMENT

The operating environment controls whether external mem- ory is supported and whether the reset vector jumps to a code space intended to support In-System Programming (ISP). Up to 12M of external memory space is available. The operating mode of the device is controlled by the states on the ENV[2:0] pins at reset and the states of the EMPTY bits in the Protection Word, as shown in Table 7. Internal pullups on the ENV[2:0] pins select IRE mode or ISP mode if these pins are allowed to float. When ENV[2:0] = 111b, IRE mode is selected unless the EMPTY bits in the Protection word indicate that the program flash memory is empty (unprogrammed), in which case ISP mode is selected. When ENV[2:0] = 011b, ERE mode is se- lected unless the EMPTY bits indicate that the program flash memory is empty, in which case ISP mode is selected. When ENV[2:0] = 110b, ISP mode is selected without re- gard to the states of the EMPTY bits. See Section 8.4.2 for more details. In the DEV environment, the on-chip flash memory is dis- abled, and the corresponding region of the address space is mapped to external memory. DEVINT mode is equivalent to DEV mode but maps static memory zone 0 to the on-chip memory. Start Address End Address Size in Bytes Description BIU Zone 00 0000h 03 FFFFh 256K On-chip Flash Program Memory, including Boot Memory Static Zone 0 (mapped internally in IRE and ERE mode; mapped to the external bus in DEV mode) 04 0000h 0C FFFFh 576K Reserved 0D 0000h 0D 1FFFh 8K On-chip Flash Data Memory 0D 2000h 0D FFFFh 56K Reserved 0E 0000h 0E 7FFFh 32K System RAM N/A 0E 8000h 0E 91FFh 4.5K Bluetooth Data RAM 0E 9200h 0E E7FFh 21.5K Reserved 0E E800h 0E EBFFh 1K Bluetooth Lower Link Controller Sequencer RAM 0E EC00h 0E EFFFh 1K Reserved 0E F000h 0E F13Fh 320 CAN0 Buffers and Registers 0E F140h 0E F17Fh 64 Reserved 0E F180h 0E F1FFh 128 Bluetooth Lower Link Controller Registers 0E F200h 0E F33Fh 320 CAN1 Buffers and Registers 0E F320h 0F FFFFh 67K Reserved 10 0000h 3F FFFFh 3072K Reserved 40 0000h 7F FFFFh 4096K External Memory Zone 1 Static Zone 1 80 0000h FE FFFFh 8128K External Memory Zone 2 Static Zone 2 FF 0000h FF F1FFh 61952 Reserved FF F200h FF F5FFh 1K Peripherals and Other I/O Ports N/A FF F600h FF FAFFh 1280 BIU, DMA, Flash interfaces IN/A FF FB00h FF FBFFh 256 I/O Expansion I/O Zone FF FC00h FF FFFFh 1K Peripherals and Other I/O Ports N/A Obsolete

25 www.national.com CP3BT23

6.2 BUS INTERFACE UNIT (BIU)

The BIU controls the interface between the CPU core bus and those on-chip modules which are mapped into BIU zones. These on-chip modules are the flash program mem- ory and the I/O zone. The BIU controls the configured pa- rameters for bus access (such as the number of wait states for memory access) and issues the appropriate bus signals for the requested access.

6.3 BUS CYCLES

There are four types of data transfer bus cycles: ! Normal read ! Fast read ! Early write ! Late write The type of data cycle used in a particular transaction de- pends on the type of CPU operation (a write or a read), the type of memory or I/O being accessed, and the access type programmed into the BIU control registers (early/late write or normal/fast read). For read operations, a basic normal read takes two clock cy- cles, and a fast-read bus cycle takes one clock cycle. Nor- mal read bus cycles are enabled by default after reset. For write operations, a basic late-write bus cycle takes two clock cycles, and a basic early-write bus cycle takes three clock cycles. Early-write bus cycles are enabled by default after reset. However, late-write bus cycles are needed for ordinary write operations, so this configuration must be changed by software (see Section 6.4.1). In certain cases, one or more additional clock cycles are added to a bus access cycle. There are two types of addi- tional clock cycles for ordinary memory accesses, called in- ternal wait cycles (TIW) and hold (Thold) cycles. A wait cycle is inserted in a bus cycle just after the memory address has been placed on the address bus. This gives the accessed memory more time to respond to the transaction request. A hold cycle is inserted at the end of a bus cycle. This holds the data on the data bus for an extended number of clock cy- cles.

6.4 BIU CONTROL REGISTERS

The BIU has a set of control registers that determine how many wait cycles and hold cycles are to be used for access- ing memory. During initialization of the system, these regis- ters should be programmed with appropriate values so that the minimum allowable number of cycles is used. This num- ber varies with the clock frequency. There are five BIU control registers, as listed in Table 8. These registers control the bus cycle configuration used for accessing the various on-chip memory types.

6.4.1 BIU Configuration Register (BCFG)

The BCFG register is a byte-wide, read/write register that selects early-write or late-write bus cycles. At reset, the reg- ister is initialized to 07h. The register format is shown below. EWR The Early Write bit controls write cycle timing. – Late-write operation (2 clock cycles to write). 1 – Early-write operation. At reset, the BCFG register is initialized to 07h, which se- lects early-write operation. However, late-write operation is required for normal device operation, so software must change the register value to 06h. Bits 1 and 2 of this register must always be set when writing to this register. Table 7 Operating Environment Selection ENV[2:0] EMPTY Operating Environment

111 No Internal ROM enabled (IRE) mode

011 No External ROM enabled (ERE) mode

000 N/A Development (DEV) mode

001 N/A Development (DEVINT) mode with

110 N/A In-System-Programming (ISP) mode

111 Y es In-System-Programming (ISP) mode

011 Y es In-System-Programming (ISP) mode

Table 8 Bus Control Registers Name Address Description BCFG FF F900h BIU Configuration Register IOCFG FF F902h I/O Zone Configuration Register SZCFG0 FF F904h Static Zone 0 Configuration Register SZCFG1 FF F906h Static Zone 1 Configuration Register SZCFG2 FF F908h Static Zone 2 Configuration Register 7 3 2 1 0 Reserved 1 1 EWR Obsolete

www.national.com 26 CP3BT23

6.4.2 I/O Zone Configuration Register (IOCFG)

The IOCFG register is a word-wide, read/write register that controls the timing and bus characteristics of accesses to the 256-byte I/O Zone memory space (FF FB00h to FF FBFFh). The registers associated with Port B and Port C re- side in the I/O memory array. At reset, the register is initial- ized to 069Fh. The register format is shown below. WAIT The Memory Wait Cycles field specifies the number of TIW (internal wait state) clock cy- cles added for each memory access, ranging from 000 binary for no additional TIW wait cy- cles to 111 binary for seven additional TIW wait cycles. HOLD The Memory Hold Cycles field specifies the number of Thold clock cycles used for each memory access, ranging from 00b for no Thold cycles to 11b for three Thold clock cy- cles. BW The Bus Width bit defines the bus width of the IO Zone. – 8-bit bus width. 1 – 16-bit bus width (default) IPST The Post Idle bit controls whether an idle cycle follows the current bus cycle, when the next bus cycle accesses a different zone. No idle cycles are required for on-chip accesses. – No idle cycle (recommended). 1 – Idle cycle.

6.4.3 Static Zone 0 Configuration Register (SZCFG0)

The SZCFG0 register is a word-wide, read/write register that controls the timing and bus characteristics of Zone 0 memory accesses. Zone 0 is used for the on-chip flash memory (including the boot area, program memory, and data memory). At reset, the register is initialized to 069Fh. The register for- mat is shown below. WAIT The Memory Wait field specifies the number of TIW (internal wait state) clock cycles added for each memory access, ranging from 000b for no additional TIW wait cycles to 111b for seven additional TIW wait cycles. These bits are ignored if the SZCFG0.FRE bit is set. HOLD The Memory Hold field specifies the number of Thold clock cycles used for each memory access, ranging from 00b for no Thold cycles to 11b for three Thold clock cycles. These bits are ignored if the SZCFG0.FRE bit is set. RBE The Read Burst Enable enables burst cycles on 16-bit reads from 8-bit bus width regions of the address space. Because the flash pro- gram memory is required to be 16-bit bus width, the RBE bit is a don’t care bit. This bit is ignored when the SZCFG0.FRE bit is set. – Burst read disabled. 1 – Burst read enabled. WBR The Wait on Burst Read bit controls if a wait state is added on burst read transaction. This bit is ignored, when SZCFG0.FRE bit is set or when SZCFG0.RBE is clear. – No TBW on burst read cycles. 1 – One TBW on burst read cycles. BW The Bus Width bit controls the bus width of the zone. The flash program memory must be configured for 16-bit bus width. – 8-bit bus width. 1 – 16-bit bus width (required). FRE The Fast Read Enable bit controls whether fast read bus cycles are used. A fast read op- eration takes one clock cycle. A normal read operation takes at least two clock cycles. – Normal read cycles. 1 – Fast read cycles. IPST The Post Idle bit controls whether an idle cycle follows the current bus cycle, when the next bus cycle accesses a different zone. No idle cycles are required for on-chip accesses. – No idle cycle (recommended). 1 – Idle cycle inserted. 7 6 5 4 3 2 0 BW Reserved HOLD WAIT 15 10 9 8 Reserved IPST Res. 7 6 5 4 3 2 0 BW WBR RBE HOLD WAIT 15 12 11 10 9 8 Reserved FRE IPRE IPST Res. Obsolete

27 www.national.com CP3BT23 IPRE The Preliminary Idle bit controls whether an idle cycle is inserted prior to the current bus cycle, when the new bus cycle accesses a dif- ferent zone. No idle cycles are required for on- chip accesses. – No idle cycle (recommended). 1 – Idle cycle inserted.

6.4.4 Static Zone 1 Configuration Register (SZCFG1)

The SZCFG1 register is a word-wide, read/write register that controls the timing and bus characteristics for off-chip accesses selected with the SEL1 output signal. At reset, the register is initialized to 069Fh. The register for- mat is shown below. WAIT The Memory Wait field specifies the number of TIW (internal wait state) clock cycles added for each memory access, ranging from 000b for no additional TIW wait cycles to 111b for seven additional TIW wait cycles. These bits are ignored if the SZCFG1.FRE bit is set. HOLD The Memory Hold field specifies the number of Thold clock cycles used for each memory access, ranging from 00b for no Thold cycles to 11b for three Thold clock cycles. These bits are ignored if the SZCFG1.FRE bit is set. RBE The Read Burst Enable enables burst cycles on 16-bit reads from 8-bit bus width regions of the address space. This bit is ignored when the SZCFG1.FRE bit is set or the SZCFG1.BW is clear. – Burst read disabled. 1 – Burst read enabled. WBR The Wait on Burst Read bit controls if a wait state is added on burst read transaction. This bit is ignored, when SZCFG1.FRE bit is set or when SZCFG1.RBE is clear. – No TBW on burst read cycles. 1 – One TBW on burst read cycles. BW The Bus Width bit controls the bus width of the zone. 0 – 8-bit bus width. 1 – 16-bit bus width. FRE The Fast Read Enable bit controls whether fast read bus cycles are used. A fast read op- eration takes one clock cycle. A normal read operation takes at least two clock cycles. – Normal read cycles. 1 – Fast read cycles. IPST The Post Idle bit controls whether an idle cycle follows the current bus cycle, when the next bus cycle accesses a different zone. – No idle cycle. 1 – Idle cycle inserted. IPRE The Preliminary Idle bit controls whether an idle cycle is inserted prior to the current bus cycle, when the new bus cycle accesses a dif- ferent zone. – No idle cycle. 1 – Idle cycle inserted.

6.4.5 Static Zone 2 Configuration Register (SZCFG2)

The SZCFG2 register is a word-wide, read/write register that controls the timing and bus characteristics for off-chip accesses selected with the SEL2 output signal. At reset, the register is initialized to 069Fh. The register for- mat is shown below. WAIT The Memory Wait field specifies the number of TIW (internal wait state) clock cycles added for each memory access, ranging from 000b for no additional TIW wait cycles to 111b for seven additional TIW wait cycles. These bits are ignored if the SZCFG2.FRE bit is set. HOLD The Memory Hold field specifies the number of Thold clock cycles used for each memory access, ranging from 00b for no Thold cycles to 11b for three Thold clock cycles. These bits are ignored if the SZCFG2.FRE bit is set. RBE The Read Burst Enable enables burst cycles on 16-bit reads from 8-bit bus width regions of the address space. This bit is ignored when the SZCFG2.FRE bit is set or the SZCFG2.BW is clear. – Burst read disabled. 1 – Burst read enabled. WBR The Wait on Burst Read bit controls if a wait state is added on burst read transaction. This bit is ignored, when SZCFG2.FRE bit is set or when SZCFG2.RBE is clear. – No TBW on burst read cycles. 1 – One TBW on burst read cycles. BW The Bus Width bit controls the bus width of the zone. 0 – 8-bit bus width. 1 – 16-bit bus width. 7 6 5 4 3 2 0 BW WBR RBE HOLD WAIT 15 12 11 10 9 8 Reserved FRE IPRE IPST Res. 7 6 5 4 3 2 0 BW WBR RBE HOLD WAIT 15 12 11 10 9 8 Reserved FRE IPRE IPST Res. Obsolete

www.national.com 28 CP3BT23 FRE The Fast Read Enable bit controls whether fast read bus cycles are used. A fast read op- eration takes one clock cycle. A normal read operation takes at least two clock cycles. – Normal read cycles. 1 – Fast read cycles. IPST The Post Idle bit controls whether an idle cycle follows the current bus cycle, when the next bus cycle accesses a different zone. 0 – No idle cycle. 1 – Idle cycle inserted. IPRE The Preliminary Idle bit controls whether an idle cycle is inserted prior to the current bus cycle, when the new bus cycle accesses a dif- ferent zone. – No idle cycle. 1 – Idle cycle inserted.

6.5 WAIT AND HOLD STATES

The number of wait cycles and hold cycles inserted into a bus cycle depends on whether it is a read or write operation, the type of memory or I/O being accessed, and the control register settings.

6.5.1 Flash Program/Data Memory

When the CPU accesses the Flash program and data mem- ory (address ranges 000000h –03FFFFh and 0E0000h – 0E1FFFh), the number of added wait and hold cycles de- pends on the type of access and the BIU register settings. In fast-read mode (SZCFG0.FRE=1), a read operation is a single cycle access. This limits the maximum CPU operat- ing frequency to 24 MHz. For a read operation in normal-read mode (SZCFG0.FRE=0), the number of inserted wait cycles is specified in the SZCFG0.WAIT field. The total number of wait cycles is the value in the WAIT field plus 1, so it can range from 1 to 8. The number of inserted hold cycles is specified in the SCCFG0.HOLD field, which can range from 0 to 3. For a write operation in fast read mode (SZCFG0.FRE=1), the number of inserted wait cycles is 1. No hold cycles are used. For a write operation normal read mode (SZCFG0.FRE=0), the number of wait cycles is equal to the value written to the SZCFG0.WAIT field plus 1 (in the late write mode) or 2 (in the early write mode). The number of inserted hold cycles is equal to the value written to the SCCFG0.HOLD field, which can range from 0 to 3.

6.5.2 RAM Memory

Read and write accesses to on-chip RAM is performed with- in a single cycle, without regard to the BIU settings. The RAM address is in the range of 0E 0000h –0E 7FFFh and 0E 8000h–0E 91FFh.

6.5.3 Access to Peripherals

When the CPU accesses on-chip peripherals in the range of 0E F000h–0E F1FFh and FF 0000h–FF FBFFh, one wait cycle and one preliminary idle cycle is used. No hold cycles are used. The IOCFG register determines the access timing for the address range FF FB00h–FF FBFFh. Obsolete

29 www.national.com CP3BT23

7.0 System Configuration Registers

The system configuration registers control and provide sta- tus for certain aspects of device setup and operation, such as indicating the states sampled from the ENV[2:0] inputs. The system configuration registers are listed in Table 9.

7.1 MODULE CONFIGURATION REGISTER

(MCFG) The MCFG register is a byte-wide, read/write register that selects the clock output features of the device. The register must be written in active mode only, not in pow- er save, HALT, or IDLE mode. However, the register con- tents are preserved during all power modes. The MCFG register format is shown below. EXIOE The EXIOE bit controls whether the external bus is enabled in the IRE environment for im- plementing the I/O Zone (FF FB00h–FF FBFFh). 0 – External bus disabled. 1 – External bus enabled. PLLCLKOE The PLLCLKOE bit controls whether the PLL clock is driven on the ENV0/PLLCLK pin. – ENV0/PLLCLK pin is high impedance. 1 – PLL clock driven on the ENV0/PLLCLK pin. MCLKOE The MCLKOE bit controls whether the Main Clock is driven on the ENV1/CPUCLK pin. – ENV1/CPUCLK pin is high impedance. 1 – Main Clock is driven on the ENV1/CPU- CLK pin. SCLKOE The SCLKOE bit controls whether the Slow Clock is driven on the ENV2/SLOWCLK pin. – ENV2/SLOWCLK pin is high impedance. 1 – Slow Clock is driven on the ENV2/SLOW- CLK pin. MISC_IO_SPEED The MISC_IO_SPEED bit controls the slew rate of the output drivers for the ENV[2:0], RDY , RFDATA, and TDO pins. T o minimize noise, the slow slew rate is recommended. 0 – Fast slew rate. 1 – Slow slew rate. MEM_IO_SPEED The MEM_IO_SPEED bit controls the slew rate of the output drivers for the A[22:0], RD SEL[2:0], SELIO , WR[1:0], PB[7:0], and PC[7:0] pins. Memory speeds for the CP3BT23 are characterized with fast slew rate. Slow slew rate reduces the available memory access time by 5 ns. – Fast slew rate. 1 – Slow slew rate. Table 9 System Configuration Registers Name Address Description MCFG FF F910h Module Configuration Register MSTAT FF F914h Module Status Register 7 6 5 4 3 2 1 0 Res. MEM_IO_ SPEED MISC_IO_ SPEED Res. SCLK OE MCLK OE PLLCLK OE EXI OE Obsolete

www.national.com 30 CP3BT23

7.2 MODULE STATUS REGISTER (MSTAT)

The MSTAT register is a byte-wide, read-only register that indicates the general status of the device. The MCFG regis- ter format is shown below. OENV2:0 The Operating Environment bits hold the states sampled from the ENV[2:0] input pins at reset. These states are controlled by exter- nal hardware at reset and are held constant in the register until the next reset. PGMBUSY The Flash Programming Busy bit is automati- cally set when either the program memory or the data memory is being programmed or erased. It is clear when neither of the memo- ries is busy. When this bit is set, software must not attempt to program or erase either of these two memories. This bit is a copy of the FMBUSY bit in the FMSTAT register. – Flash memory is not busy. 1 – Flash memory is busy. DPGMBUSY The Data Flash Programming Busy indicates that the flash data memory is being erased or a pipelined programming sequence is current- ly ongoing. Software must not attempt to per- form any write access to the flash program memory at this time, without also polling the FSMSTAT .FMFULL bit in the flash memory in- terface. The DPGMBUSY bit is a copy of the FMBUSY bit in the FSMSTAT register. – Flash data memory is not busy. 1 – Flash data memory is busy. WDRST The Watchdog Reset bit indicates that a Watchdog timer reset has occurred. Write a 1 to this bit to clear it. Power-on reset or external reset also clear this bit. – No Watchdog timer reset has occurred since this bit was last cleared. 1 – A Watchdog timer reset has occurred since this bit was last cleared. ISPRST The Software ISP Reset bit indicates that a software ISP reset has occurred since the bit was last cleared. This bit is cleared by a SWRESET(CLR) sequence, a power-on re- set, or an external reset. – No software ISP reset has occurred since this bit was last cleared. 1 – A software ISP reset has occurred since this bit was last cleared.

7.3 SOFTWARE RESET REGISTER

(SWRESET) The SWRESET register is a byte-wide, write-only register which provides a mechanism for software to initiate a reset into ISP mode without regard to the status of the EMPTY bits in the flash protection word. This form of reset is only al- lowed when all of the following conditions are true: ! The device is in IRE or ERE mode ! BOOTAREA is defined (has a value other than 1111b) in the Protection Word (see Section 8.4.2 for more details). ! ISPE is set in the flash protection word, indicating that there is ISP code in the flash To initiate a reset under these conditions, it is necessary to write the value E1h to the SWRESET register, followed with- in 127 clock cycles by the value 3Eh. The reset then follows immediately. This sequence is called SWRESET(ISP). Once the device has been reset into ISP mode by SWRE- SET(ISP), any subsequent reset (other than internal or ex- ternal power-on reset) will cause the part to reset into ISP mode because the EMPTY bits in the Protection Word con- tinue to be ignored. A second set of special values written to the SWRESET reg- ister will cause a reset out of ISP mode (whether or not the device is currently in ISP mode). This can be used as a sim- ple software reset. In this case, no conditions are checked. To initiate reset out of ISP mode, write the value E1h to the SWRESET register, followed within 127 clock cycles by the value 0Eh. The reset then follows immediately. This se- quence is called SWRESET(CLR). This reset also cancels the effect of any previous SWRESET(ISP), so subsequent resets will check the EMPTY bits to determine whether to enter ISP mode. The ISP reset behaves similarly to the Watchdog reset, for example, if the flash interface is busy when reset is assert- ed, the reset to the clock module is delayed until the flash operations are completed. 7 6 5 4 3 2 0 ISPRST WDRST Res. DPGMBUSY PGMBUSY OENV2:0 Obsolete

31 www.national.com CP3BT23

8.0 Flash Memory

The flash memory consists of the flash program memory and the flash data memory. The flash program memory is further divided into the Boot Area and the Code Area. A special protection scheme is applied to the lower portion of the flash program memory, called the Boot Area. The Boot Area always starts at address 0 and ranges up to a programmable end address. The maximum boot area ad- dress which can be selected is 00 77FFh. The intended use of this area is to hold In-System-Programming (ISP) rou- tines or essential application routines. The Boot Area is al- ways protected against CPU write access, to avoid unintended modifications. The Code Area is intended to hold the application code and constant data. The Code Area begins with the next byte af- ter the Boot Area. T able 10 summarizes the properties of the regions of flash memory mapped into the CPU address space. Table 10 Flash Memory Areas

8.1 FLASH MEMORY PROTECTION

The memory protection mechanisms provide both global and section-level protection. Section-level protection against CPU writes is applied to individual 8K-byte sections of the flash program memory and 512-byte sections of the flash data memory. Section-level protection is controlled through read/write registers mapped into the CPU address space. Global write protection is applied at the device level, to disable flash memory writes by the CPU. Global write pro- tection is controlled by the encoding of bits stored in the flash memory array.

8.1.1 Section-Level Protection

Each bit in the Flash Memory Write Enable (FM0WER and FM1WER) registers enables or disables write access to a corresponding section of flash program memory. Write ac- cess to the flash data memory is controlled by the bits in the Flash Slave Memory Write Enable (FSM0WER) register. By default (after reset) all bits in the FM0WER, FM1WER, and FSM0WER registers are cleared, which disables write ac- cess by the CPU to all sections. Write access to a section is enabled by setting the corresponding write enable bit. After completing a programming or erase operation, software should clear all write enable bits to protect the flash program memory against any unintended writes.

8.1.2 Global Protection

The WRPROT field in the Protection Word controls global write protection. The Protection Word is located in a special flash memory outside of the CPU address space. If a major- ity of the bits in the 3-bit WRPROT field are clear, write pro- tection is enabled. Enabling this mode prevents the CPU from writing to flash memory. The RDPROT field in the Protection Word controls global read protection. If a majority of the bits in the 3-bit RDPROT field are clear, read protection is enabled. Enabling this mode prevents reading by an external debugger through the serial debug interface or by an external flash programmer. CPU read access is not affected by the RDPROT bits.

8.2 FLASH MEMORY ORGANIZATION

Each of the flash memories are divided into main blocks and information blocks. The main blocks hold the code or data used by application software. The information blocks hold factory parameters, protection settings, and other device- specific data. The main blocks are mapped into the CPU ad- dress space. The information blocks are accessed indirectly through a register-based interface. Separate sets of regis- ters are provided for accessing flash program memory (FM registers) and flash data memory (FSM registers). The flash program memory consists of two main blocks and two data blocks, as shown in Table 11. The flash data memory con- sists of one main block and one information block. Table 11 Flash Memory Blocks Area Address Range Read Access Write Access Boot Area 0 –BOOTAREA - 1 Y es No Code Area BOOTAREA –03 FFFFh Y es Write access only if section write enable bit is set and global write protection is disabled. Data Area 0D 0000h–0D 1FFFh Y es Write access only if section write enable bit is set and global write protection is disabled. Name Address Range Function Main Block 0 00 0000h–01 FFFFh (CPU address space) Flash Program Memory Information Block 0 000h–07Fh (address register) Function Word, Factory Parameters Main Block 1 02 0000h–03 FFFFh (CPU address space) Flash Program Memory Information Block 1 080h–0FFh (address register) Protection Word, User Data Main Block 20D 0000h–0D 1FFFh (CPU address space) Flash Data Memory Information Block 2 000h–07Fh (address register) User Data Obsolete

www.national.com 32 CP3BT23

8.2.1 Main Block 0 and 1

Main Block 0 and Main Block 1 hold the 256K-byte program space, which consists of the Boot Area and Code Area. Each block consists of sixteen 8K-byte sections. Write ac- cess by the CPU to Main Block 0 and Main Block 1 is con- trolled by the corresponding bits in the FM0WER and FM1WER registers, respectively. The least significant bit in each register controls the section at the lowest address.

8.2.2 Information Block 0

Information Block 0 contains 128 bytes, of which one 16-bit word has a dedicated function, called the Function Word. The Function Word resides at address 07Eh. The remaining Information Block 0 locations are used to hold factory pa- rameters. Software only has read access to Information Block 0 through a register-based interface. The Function Word and the factory parameters are protected against CPU writes. Table 12 shows the structure of Information Block 0. Table 12 Information Block 0

8.2.3 Information Block 1

Information Block 1 contains 128 bytes, of which one 16-bit word has a dedicated function, called the Protection Word. The Protection Word resides at address 0FEh. It controls the global protection mechanisms and the size of the Boot Area. The Protection Word can be written by the CPU, how- ever the changes only become valid after the next device re- set. The remaining Information Block 1 locations can be used to store other user data. Erasing Information Block 1 also erases Main Block 1. Table 13 shows the structure of the Information Block 1. Table 13 Information Block 1

8.2.4 Main Block 2

Main Block 2 holds the 8K-byte data area, which consists of sixteen 512-byte sections. Write access by the CPU to Main Block 2 is controlled by the corresponding bits in the FSM0WER register. The least significant bit in the register controls the section at the lowest address.

8.2.5 Information Block 2

Information Block 2 contains 128 bytes, which can be used to store user data. The CPU can always read Information Block 2. The CPU can write Information Block 2 only when global write protection is disabled. Erasing Information Block 2 also erases Main Block 2.

8.3 FLASH MEMORY OPERATIONS

Flash memory programming (erasing and writing) can be performed on the flash data memory while the CPU is exe- cuting out of flash program memory. Although the CPU can execute out of flash data memory, it cannot erase or write the flash program memory while executing from flash data memory. To erase or write the flash program memory, the CPU must be executing from the on-chip static RAM or off- chip memory. An erase operation is required before programming. An erase operation sets all of the bits in the erased region. A programming operation clears selected bits. The programming mechanism is pipelined, so that a new write request can be loaded while a previous request is in progress. When the FMFULL bit in the FMSTAT or FSM- STAT register is clear, the pipeline is ready to receive a new request. New requests may be loaded after checking only the FMFULL bit.

8.3.1 Main Block Read

Read accesses from flash program memory can only occur when the flash program memory is not busy from a previous write or erase operation. Read accesses from the flash data memory can only occur when both the flash program mem- ory and the flash data memory are not busy. Both byte and word read operations are supported.

8.3.2 Information Block Read

Information block data is read through the register-based in- terface. Only word read operations are supported and the read address must be word-aligned (LSB = 0). The following steps are used to read from an information block: 1. Load the word address in the Flash Memory Informa- tion Block Address (FMIBAR) or Flash Slave Memory Information Block Address (FSMIBAR) register. 2. Read the data word by reading out the Flash Memory Information Block Data (FMIBDR) or Flash Slave Mem- ory Information Block Data (FSMIBDR) register. Name Address Range Read Access Write Access Function Word 07Eh –07Fh Ye s NoOther (Used for Factory Parameters) 000h–07Dh Name Address Range Read Access Write Access Protection Word 0FEh –0FFh Yes Write access only if section write enable bit is set and global write protection is dis- abled. Other (User Data) 080h–0FDh Obsolete

33 www.national.com CP3BT23

8.3.3 Main Block Page Erase

A flash erase operation sets all of the bits in the erased re- gion. Pages of a main block can be individually erased if their write enable bits are set. This method cannot be used to erase the boot area, if defined. Each page in Main Block 0 and 1 consists of 1024 bytes (512 words). Each page in Main Block 2 consists of 512 bytes (256 words). To erase a page, the following steps are performed: 1. Verify that the Flash Memory Busy (FMBUSY) bit in the FMSTAT or FSMST AT register is clear. 2. Prevent accesses to the flash memory while erasing is in progress. 3. Set the Page Erase (PER) bit in the FMCTRL or FSM- CTRL register. 4. Write to an address within the desired page. 5. Wait until the FMBUSY bit becomes clear again. 6. Check the Erase Error (EERR) bit in the FMSTAT or FSMSTAT register to confirm successful erase of the page. 7. Repeat steps 4 through 6 to erase additional pages. 8. Clear the PER bit.

8.3.4 Main Block Module Erase

A module erase operation can be used to erase an entire main block. All sections within the block must be enabled for writing. If a boot area is defined in the block, it cannot be erased. The following steps are performed to erase a main block: 1. Verify that the Flash Memory Busy (FMBUSY) bit in the FMSTAT or FSMST AT register is clear. 2. Prevent accesses to the flash memory while erasing is in progress. 3. Set the Module Erase (MER) bit in the FMCTRL or FSMCTRL register. 4. Write to any address within the desired main block. 5. Wait until the FMBUSY bit becomes clear again. 6. Check the Erase Error (EERR) bit in the FMSTAT or FSMSTAT register to confirm successful erase of the block. 7. Clear the MER bit.

8.3.5 Information Block Module Erase

Erasing an information block also erases the corresponding main block. If a boot area is defined in the main block, nei- ther block can be erased. Page erase is not supported for information blocks. The following steps are performed to erase an information block: 1. Verify that the Flash Memory Busy (FMBUSY) bit in the FMSTAT or FSMST AT register is clear. 2. Prevent accesses to the flash memory while erasing is in progress. 3. Set the Module Erase (MER) bit in the FMCTRL or FSMCTRL register. 4. Load the FMIBAR or FSMIBAR register with any ad- dress within the block, then write any data to the FMIB- DR or FSMIBDR register. 5. Wait until the FMBUSY bit becomes clear again. 6. Check the Erase Error (EERR) bit in the FMSTAT or FSMSTAT register to confirm successful erase of the block. 7. Clear the MER bit.

8.3.6 Main Block Write

Writing is only allowed when global write protection is dis- abled. Writing by the CPU is only allowed when the write en- able bit is set for the sector which contains the word to be written. The CPU cannot write the Boot Area. Only word- wide write access to word-aligned addresses is supported. The following steps are performed to write a word: 1. Verify that the Flash Memory Busy (FMBUSY) bit in the FMSTAT or FSMSTAT register is clear. 2. Prevent accesses to the flash memory while the write is in progress. 3. Set the Program Enable (PE) bit in the FMCTRL or FSMCTRL register. 4. Write a word to the desired word-aligned address. This starts a new pipelined programming sequence. The FMBUSY bit becomes set while the write operation is in progress. The FMFULL bit in the FMSTAT or FSMSTAT register becomes set if a previous write operation is still in progress. 5. Wait until the FMFULL bit becomes clear. 6. Repeat steps 4 and 5 for additional words. 7. Wait until the FMBUSY bit becomes clear again. 8. Check the programming error (PERR) bit in the FM- STAT or FSMSTAT register to confirm successful pro- gramming. 9. Clear the Program Enable (PE) bit.

8.3.7 Information Block Write

Writing is only allowed when global write protection is dis- abled. Writing by the CPU is only allowed when the write en- able bit is set for the sector which contains the word to be written. The CPU cannot write Information Block 0. Only word-wide write access to word-aligned addresses is sup- ported. The following steps are performed to write a word: 1. Verify that the Flash Memory Busy (FMBUSY) bit in the FMSTAT or FSMSTAT register is clear. 2. Prevent accesses to the flash memory while the write is in progress. 3. Set the Program Enable (PE) bit in the FMCTRL or FSMCTRL register. 4. Write the desired target address into the FMIBAR or FSMIBAR register. 5. Write the data word into the FMIBDR or FSMIBDR reg- ister. This starts a new pipelined programming se- quence. The FMBUSY bit becomes set while the write operation is in progress. The FMFULL bit in the FM- STAT or FSMSTAT register becomes set if a previous write operation is still in progress. 6. Wait until the FMFULL bit becomes clear. 7. Repeat steps 4 through 6 for additional words. 8. Wait until the FMBUSY bit becomes clear again. 9. Check the programming error (PERR) bit in the FM- STAT or FSMSTAT register to confirm successful pro- gramming. 10. Clear the Program Enable (PE) bit. Obsolete

www.national.com 34 CP3BT23

8.4 INFORMATION BLOCK WORDS

Two words in the information blocks are dedicated to hold settings that affect the operation of the system: the Function Word in Information Block 0 and the Protection Word in In- formation Block 1.

8.4.1 Function Word

The Function Word resides in the Information Block 0 at ad- dress 07Eh. At reset, the Function Word is copied into the FMAR0 register.

8.4.2 Protection Word

The Protection Word resides in Information Block 1 at ad- dress 0FEh. At reset, the Protection Word is copied into the FMAR1 register. BOOTAREA The BOOTAREA field specifies the size of the Boot Area. The Boot Area starts at address 0 and ends at the address specified by this field. The inverted bits of the BOOTAREA field count the number of 2048-byte blocks to be reserved as the Boot Area. The maximum Boot Area size is 30K bytes (address range 0 to 77FFh). The end of the Boot Area defines the start of the Code Area. If the device starts in ISP mode and there is no Boot Area defined (encoding 1111b), the device is kept in reset. Table 14 lists all possible boot area encod- ings. EMPTY The EMPTY field indicates whether the flash program memory has been programmed or should be treated as blank. If a majority of the three EMPTY bits are clear, the flash program memory is treated as programmed. If a major- ity of the EMPTY bits are set, the flash pro- gram memory is treated as empty. If the ENV[1:0] inputs (see Section 6.1) are sam- pled high at reset and the EMPTY bits indicate the flash program memory is empty, the de- vice will begin execution in ISP mode. The de- vice enters ISP mode without regard to the EMPTY status if ENV0 is driven low and ENV1 is driven high. ISPE The ISPE field indicates whether the Boot Area is used to hold In-System-Programming routines or user application routines. If a ma- jority of the three ISPE bits are set, the Boot Area is intended to store ISP routines. If ma- jority of the ISPE bits are clear, the Boot Area holds user application routines. Table 15 sum- marizes all possible EMPTY , ISPE, and Boot Area settings and the corresponding start-up operation for each combination. In DEV mode, the EMPTY bit settings are ignored and the CPU always starts executing from address 15 0 Reserved 15 13 12 10 9 7 6 4 3 1 0 WRPROT RDPROT ISPE EMPTY BOOTAREA Table 14 Boot Area Encodings BOOT AREA Size of the Boot Area Code Area Start Address

1111 No Boot Area defined 00 0000h

35 www.national.com CP3BT23 RDPROT The RDPROT field controls the global read protection mechanism for the on-chip flash program memory. If a majority of the three RDPROT bits are clear, the flash program memory is protected against read access from the serial debug interface or an external flash programmer. CPU read access is not af- fected by the RDPROT bits. If a majority of the RDPROT bits are set, read access is allowed. WRPROT The WRPROT field controls the global write protection mechanism for the on-chip flash program memory. If a majority of the three WRPROT bits are clear, the flash program memory is protected against write access from any source and read access from the se- rial debug interface. If a majority of the WR- PROT bits are set, write access is allowed.

8.5 FLASH MEMORY INTERFACE

There is a separate interface for the program flash and data flash memories. The same set of registers exist in both in- terfaces. In most cases they are independent of each other, but in some cases the program flash interface controls the interface for both memories, as indicated in the following sections. Table 16 lists the registers. Table 15 CPU Reset Behavior EMPTY ISPE Boot Area Start-Up Operation Not Empty ISP Defined Device starts in IRE/ ERE mode from Code Area start address Not Empty ISP Not Defined Device starts in IRE/ ERE mode from Code Area start address Not Empty No ISP Don ’t Care Device starts in IRE/ ERE mode from address 0 Empty ISP Defined Device starts in ISP mode from Code Area start address Empty ISP Not Defined Device starts in ISP mode and is kept in its reset stateEmpty No ISP Don ’t Care Table 16 Flash Memory Interface Registers Program Memory Data Memory Description FMIBAR FF F940h FSMIBAR FF F740h Flash Memory Information Block Address Register FMIBDR FF F942h FSMIBDR FF F742h Flash Memory Information Block Address Register FM0WER FF F944h FSM0WER FF F744h Flash Memory 0 Write Enable Register FM1WER FF F946h N/A Flash Memory 1 Write Enable Register FMCTRL FF F94Ch FSMCTRL FF F74Ch Flash Memory Control Register FMSTAT FF F94Eh FSMSTAT FF F74Eh Flash Memory Status Register FMPSR FF F950h FSMPSR FF F750h Flash Memory Prescaler Register FMSTART FF F952h FSMSTART FF F752h Flash Memory Start Time Reload Register FMTRAN FF F954h FSMTRAN FF F754h Flash Memory T ransition Time Reload Register FMPROG FF F956h FSMPROG FF F756h Flash Memory Programming Time Reload Register FMPERASE FF F958h FSMPERASE FF F758h Flash Memory Page Erase Time Reload Register FMMERASE0 FF F95Ah FSMMERASE0 FF F75Ah Flash Memory Module Erase Time Reload Register 0 FMEND FF F95Eh FSMEND FF F75Eh Flash Memory End Time Reload Register FMMEND FF F960h FSMMEND FF F760h Flash Memory Module Erase End Time Reload Register FMRCV FF F962h FSMRCV FF F762h Flash Memory Recovery Time Reload Register FMAR0 FF F964h FSMAR0 FF F764h Flash Memory Auto-Read Register 0 FMAR1 FF F966h FSMAR1 FF F766h Flash Memory Auto-Read Register 1 FMAR2 FF F968h FSMAR2 FF F768h Flash Memory Auto-Read Register 2 Obsolete

www.national.com 36 CP3BT23

8.5.1 Flash Memory Information Block Address

Register (FMIBAR/FSMIBAR) The FMIBAR register specifies the 8-bit address for read or write access to an information block. Because only word ac- cess to the information blocks is supported, the least signif- icant bit (LSB) of the FMIBAR must be 0 (word-aligned). The hardware automatically clears the LSB, without regard to the value written to the bit. The FMIBAR register is cleared after device reset. The CPU bus master has read/write ac- cess to this register. IBA The Information Block Address field holds the word-aligned address of an information block location accessed during a read or write transaction. The LSB of the IBA field is always clear.

8.5.2 Flash Memory Information Block Data Register

(FMIBDR/FSMIBDR) The FMIBDR register holds the 16-bit data for read or write access to an information block. The FMIBDR register is cleared after device reset. The CPU bus master has read/ write access to this register. IBD The Information Block Data field holds the data word for access to an information block. For write operations the IBD field holds the data word to be programmed into the informa- tion block location specified by the IBA ad- dress. During a read operation from an information block, the IBD field receives the data word read from the location specified by the IBA address.

8.5.3 Flash Memory 0 Write Enable Register

(FM0WER/FSM0WER) The FM0WER register controls section-level write protec- tion for the first half of the flash program memory. The FMS0WER registers controls section-level write protection for the flash data memory. Each data block is divided into 16 8K-byte sections. Each bit in the FM0WER and FSM0WER registers controls write protection for one of these sections. The FM0WER and FSM0WER registers are cleared after device reset, so the flash memory is write protected after re- set. The CPU bus master has read/write access to this reg- isters. FM0WEn The Flash Memory 0 Write Enable n bits con- trol write protection for a section of a flash memory data block. The address mapping of the register bits is shown below.

8.5.4 Flash Memory 1 Write Enable Register

(FM1WER) The FM1WER register controls write protection for the sec- ond half of the program flash memory. The data block is di- vided into 16 8K-byte sections. Each bit in the FM1WER register controls write protection for one of these sections. The FM1WER register is cleared after device reset, so the flash memory is write protected after reset. The CPU bus master has read/write access to this registers. FM1WEn The Flash Memory 1 Write Enable n bits con- trol write protection for a section of a flash memory data block. The address mapping of the register bits is shown below. 15 8 7 0 Reserved IBA 15 0 IBD 15 0 FM0WE Bit Logical Address Range 0 00 0000h–00 1FFFh 1–14 . . . 15 01 E000h –01 FFFFh 15 0 FM1WE Bit Logical Address Range 0 02 0000h–02 1FFFh 1–14 . . . 15 03 E000h –03 FFFFh Obsolete

37 www.national.com CP3BT23

8.5.5 Flash Data Memory 0 Write Enable Register

(FSM0WER) The FSM0WER register controls write protection for the flash data memory. The data block is divided into 16 512- byte sections. Each bit in the FSM0WER register controls write protection for one of these sections. The FSM0WER register is cleared after device reset, so the flash memory is write protected after reset. The CPU bus master has read/ write access to this registers. FSM0WEn The Flash Data Memory 0 Write Enable n bits control write protection for a section of a flash memory data block. The address mapping of the register bits is shown below.

8.5.6 Flash Memory Control Register (FMCTRL/

FSMCTRL) This register controls the basic functions of the Flash pro- gram memory. The register is clear after device reset. The CPU bus master has read/write access to this register. LOWPRW The Low Power Mode controls whether flash program memory is operated in low-power mode, which draws less current when data is read. This is accomplished be only accessing the flash program memory during the first half of the clock period. The low-power mode must not be used at System Clock frequencies above 25 MHz, otherwise a read access may return undefined data. This bit must not be changed while the flash program memory is busy being programmed or erased. – Normal mode. 1 – Low-power mode. CWD The CPU Write Disable bit controls whether the CPU has write access to flash memory. This bit must not be changed while FMBUSY is set. – The CPU has write access to the flash memory 1 – An external debugging tool is the current “owner” of the flash memory interface, so write accesses by the CPU are inhibited. DISVRF The Disable Verify bit controls the automatic verification feature. This bit must not be changed while the flash program memory is busy being programmed or erased. – New flash program memory contents are automatically verified after programming. 1 – Automatic verification is disabled. IENPROG The Interrupt Enable for Program bit is clear after reset. The flash program and data mem- ories share a single interrupt channel but have independent interrupt enable control bits. – No interrupt request is asserted to the ICU when the FMFULL bit is cleared. 1 – An interrupt request is made when the FMFULL bit is cleared and new data can be written into the write buffer. PE The Program Enable bit controls write access of the CPU to the flash program memory. This bit must not be altered while the flash program memory is busy being programmed or erased. The PER and MER bits must be clear when this bit is set. – Programming the flash program memory by the CPU is disabled. 1 – Programming the flash program memory is enabled. PER The Page Erase Enable bit controls whether a a valid write operation triggers an erase oper- ation on a 1024-byte page of flash memory. Page erase operations are only supported for the main blocks, not the information blocks. A page erase operation on an information block is ignored and does not alter the information block. When the PER bit is set, the PE and MER bits must be clear. This bit must not be changed while the flash program memory is busy being programmed or erased. – Page erase mode disabled. Write opera- tions are performed normally. 1 – A valid write operation to a word location in program memory erases the page that contains the word. MER The Module Erase Enable bit controls wheth- er a valid write operation triggers an erase op- eration on an entire block of flash memory. If an information block is written in this mode, both the information block and its correspond- ing main block are erased. When the MER bit is set, the PE and PER bits must be clear. This bit must not be changed while the flash pro- gram memory is busy being programmed or erased. – Module erase mode disabled. Write oper- ations are performed normally. 1 – A valid write operation to a word location in a main block erases the block that con- tains the word. A valid write operation to a word location in an information block erases the block that contains the word and its associated main block. 15 0 FSM0WE Bit Logical Address Range 0 0D 0000h –0D 01FFh 1–14 . . . 15 0D 1E00h –0D 1FFFh 7 6 5 4 3 2 1 0 MER PER PE IENPROG DISVRF Res. CWD LOWPRW Obsolete

www.national.com 38 CP3BT23

8.5.7 Flash Memory Status Register (FMSTAT/

FSMSTAT) This register reports the currents status of the on-chip Flash memory. The FLSR register is clear after device reset. The CPU bus master has read/write access to this register. EERR The Erase Error bit indicates whether an error has occurred during a page erase or module (block) erase. After an erase error occurs, software can clear the EERR bit by writing a 1 to it. Writing a 0 to the EERR bit has no effect. Software must not change this bit while the flash program memory is busy being pro- grammed or erased. – The erase operation was successful. 1 – An erase error occurred. PERR The Program Error bit indicates whether an error has occurred during programming. After a programming error occurs, software can clear the PERR bit by writing a 1 to it. Writing a 0 to the PERR bit has no effect. Software must not change this bit while the flash pro- gram memory is busy being programmed or erased. – The programming operation was suc- cessful. – A programming error occurred. FMBUSY The Flash Memory Busy bit indicates whether the flash memory (either main block or infor- mation block) is busy being programmed or erased. During that time, software must not request any further flash memory operations. If such an attempt is made, the CPU is stopped as long as the FMBUSY bit is active. The CPU must not attempt to read from pro- gram memory (including instruction fetches) while it is busy. – Flash memory is ready to receive a new erase or programming request. 1 – Flash memory busy with previous erase or programming operation. FMFULL The Flash Memory Buffer Full bit indicates whether the write buffer for programming is full or not. When the buffer is full, new erase and write requests may not be made. The IENPROG bit can be enabled to trigger an in- terrupt when the buffer is ready to receive a new request. – Buffer is ready to receive new erase or write requests. – Buffer is full. No new erase or write re- quests can be accepted. DERR The Data Loss Error bit indicates that a buffer overrun has occurred during a programming sequence. After a data loss error occurs, soft- ware can clear the DERR bit by writing a 1 to it. Writing a 0 to the DERR bit has no effect. Software must not change this bit while the flash program memory is busy being pro- grammed or erased. – No data loss error occurred. 1 – Data loss error occurred.

8.5.8 Flash Memory Prescaler Register (FMPSR/

FSMPSR) The FMPSR register is a byte-wide read/write register that selects the prescaler divider ratio. The CPU must not modify this register while an erase or programming operation is in progress (FMBUSY is set). At reset, this register is initial- ized to 04h if the flash memory is idle. The CPU bus master has read/write access to this register. FTDIV The prescaler divisor scales the frequency of the System Clock by a factor of (FTDIV + 1).

8.5.9 Flash Memory Start Time Reload Register

(FMSTART/FSMSTART) The FMSTART/FSMST ART register is a byte-wide read/ write register that controls the program/erase start delay time. Software must not modify this register while a pro- gram/erase operation is in progress (FMBUSY set). At re- set, this register is initialized to 18h if the flash memory is idle. The CPU bus master has read/write access to this reg- ister. FTSTART The Flash Timing Start Delay Count field gen- erates a delay of (FTSTART + 1) prescaler output clocks. 7 5 4 3 2 1 0 Reserved DERR FMFULL FMBUSY PERR EERR 75 4 0 Reserved FTDIV FTSTART Obsolete

39 www.national.com CP3BT23

8.5.10 Flash Memory Transition Time Reload

Register (FMTRAN/FSMTRAN) The FMTRAN/FMSTRAN register is a byte-wide read/write register that controls some program/erase transition times. Software must not modify this register while program/erase operation is in progress (FMBUSY set). At reset, this regis- ter is initialized to 30h if the flash memory is idle. The CPU bus master has read/write access to this register. FTTRAN The Flash TIming T ransition Count field spec- ifies a delay of (FTTRAN + 1) prescaler output clocks.

8.5.11 Flash Memory Programming Time Reload

Register (FMPROG/FSMPROG) The FMPROG/FSMPROG register is a byte-wide read/write register that controls the programming pulse width. Soft- ware must not modify this register while a program/erase operation is in progress (FMBUSY set). At reset, this regis- ter is initialized to 16h if the flash memory is idle. The CPU bus master has read/write access to this register. FTPROG The Flash Timing Programming Pulse Width field specifies a programming pulse width of 8 × (FTPROG + 1) prescaler output clocks.

8.5.12 Flash Memory Page Erase Time Reload

Register (FMPERASE/FSMPERASE) The FMPERASE/FSMPERASE register is a byte-wide read/write register that controls the page erase pulse width. Software must not modify this register while a program/ erase operation is in progress (FMBUSY set). At reset, this register is initialized to 04h if the flash memory is idle. The CPU bus master has read/write access to this register. FTPER The Flash Timing Page Erase Pulse Width field specifies a page erase pulse width of 4096 × (FTPER + 1) prescaler output clocks.

8.5.13 Flash Memory Module Erase Time Reload

Register 0 (FMMERASE0/FSMMERASE0) The FMMERASE0/FSMMERASE0 register is a byte-wide read/write register that controls the module erase pulse width. Software must not modify this register while a pro- gram/erase operation is in progress (FMBUSY set). At re- set, this register is initialized to EAh if the flash memory is idle. The CPU bus master has read/write access to this reg- ister. FTMER The Flash Timing Module Erase Pulse Width field specifies a module erase pulse width of 4096 × (FTMER + 1) prescaler output clocks.

8.5.14 Flash Memory End Time Reload Register

(FMEND/FSMEND) The FMEND/FSMEND register is a byte-wide read/write register that controls the delay time after a program/erase operation. Software must not modify this register while a program/erase operation is in progress (FMBUSY set). At reset, this register is initialized to 18h when the flash mem- ory on the chip is idle. The CPU bus master has read/write access to this register. FTEND The Flash Timing End Delay Count field spec- ifies a delay of (FTEND + 1) prescaler output clocks.

8.5.15 Flash Memory Module Erase End Time Reload

Register (FMMEND/FSMMEND) The FMMEND/FSMMEND register is a byte-wide read/write register that controls the delay time after a module erase op- eration. Software must not modify this register while a pro- gram/erase operation is in progress (FMBUSY set). At reset, this register is initialized to 3Ch if the flash memory is idle. The CPU bus master has read/write access to this reg- ister. FTMEND The Flash Timing Module Erase End Delay Count field specifies a delay of 8 × (FTMEND + 1) prescaler output clocks. FTTRAN FTPROG FTPER FTMER FTEND FTMEND Obsolete

www.national.com 40 CP3BT23

8.5.16 Flash Memory Recovery Time Reload Register

(FMRCV/FSMRCV) The FMRCV/FSMRCV register is a byte-wide read/write register that controls the recovery delay time between two flash memory accesses. Software must not modify this reg- ister while a program/erase operation is in progress (FM- BUSY set). At reset, this register is initialized to 04h if the flash memory is idle. The CPU bus master has read/write access to this register. FTRCV The Flash Timing Recovery Delay Count field specifies a delay of (FTRCV + 1) prescaler output clocks.

8.5.17 Flash Memory Auto-Read Register 0 (FMAR0/

FSMAR0) The FMAR0/FSMAR0 register contains a copy of the Func- tion Word from Information Block 0. The Function Word is sampled at reset. The CPU bus master has read-only ac- cess to this register. The FSMAR0 register has the same value as the FMAR0 register

8.5.18 Flash Memory Auto-Read Register 1 (FMAR1/

FSMAR1) The FMAR1 register contains a copy of the Protection Word from Information Block 1. The Protection Word is sampled at reset. The contents of the FMAR1 register define the cur- rent Flash memory protection settings. The CPU bus mas- ter has read-only access to this register. The FSMAR1 register has the same value as the FMAR1 register. The for- mat is the same as the format of the Protection Word (see Section 8.4.2).

8.5.19 Flash Memory Auto-Read Register 2 (FMAR2/

FSMAR2) The FMAR2 register is a word-wide read-only register, which is loaded during reset. It is used to build the Code Area start address. At reset, the CPU executes a branch, using the contents of the FMAR2 register as displacement. The CPU bus master has read-only access to this register. The FSMAR2 register has the same value as the FMAR2 register. CADR10:0 The Code Area Start Address (bits 10:0) con- tains the lower 11 bits of the Code Area start address. The CADR10:0 field has a fixed val- ue of 0. CADR14:11 The Code Area Start Address (bits 14:11) are loaded during reset with the inverted value of BOOTAREA3:0. CADR15 The Code Area Start Address (bits 15) con- tains the upper bit of the Code Area start ad- dress. The CADR15 field has a fixed value of FTRCV 15 0 Reserved 15 13 12 10 9 7 6 4 3 1 0 WRPROT RDPROT ISPE EMPTY BOOTAREA 1 CADR7:0 15 14 11 10 8 CADR15 CADR14:11 CADR10:8 Obsolete

9.0 DMA Controller

1. Arbitrates to become master of the CPU bus.
2. Determines priority among the DMAC channels, one

Channel 0 having the highest priority.

1. Executes data transfer bus cycle(s) selected by the val-

bus cycle that accesses the requesting device.

1. If the transfer of a block is terminated, the DMAC does

Updates the termination bits. Generates an interrupt (if enabled).

1. Returns mastership of the CPU bus to the CPU.

then on the rising edge of every clock cycle.

9.1 CHANNEL ASSIGNMENT

fers, other resources must be disabled.

9.2 TRANSFER TYPES

ry, and when the destination does not support direct mode.

9.2.1 Direct (Flyby) Transfers

anism, as shown in Figure 3. Figure 3. Direct DMA Cycle Followed by a CPU Cycle

www.national.com 42 CP3BT23 Direct mode supports two bus policies: intermittent and con- tinuous. In intermittent mode, the DMAC gives bus master- ship back to the CPU after every cycle. In continuous mode, the DMAC remains bus master until the transfer is complet- ed. The maximum bus throughput in intermittent mode is one transfer for every three System Clock cycles. The max- imum bus throughput in continuous mode is one transfer for every clock cycle. The I/O device which made the DMA request is called the implied I/O device. The other device can be either memory or another I/O device, and is called the addressed device. Because only one address is required in direct mode, this address is taken from the corresponding ADCAn counter. The DMAC channel generates either a read or a write bus cycle, as controlled by the DMACNTLn.DIR bit. When the DMACNTLn.DIR bit is clear, a read bus cycle from the addressed device is performed, and the data is written to the implied I/O device. When the DMACNTLn.DIR bit is set, a write bus cycle to the addressed device is per- formed, and the data is read from the implied I/O device. The configuration of either address freeze or address up- date (increment or decrement) is independent of the num- ber of transferred bytes, transfer direction, or number of bytes in each DMAC transfer cycle. All these can be config- ured for each channel by programming the appropriate con- trol register. Whether 8 or 16 bits are transferred in each cycle is select- ed by the DMACNTLn.TCS register bit. After the data item has been transferred, the BLTCn counter is decremented by one. The ADCAn counter is updated according to the INCA and ADA fields in the DMACNTLn register.

9.2.2 Indirect (Memory-To-Memory) Transfers

In indirect (memory-to-memory) mode, data transfers use two consecutive bus cycles. The data is first read into a tem- porary register, and then written to the destination in the fol- lowing cycle. This mode is slower than the direct (flyby) mode, but it provides support for different source and desti- nation bus widths. Indirect mode must be used for transfers between memory devices. If an intermittent bus policy is used, the maximum through- put is one transfer for every five clock cycles. If a continuous bus policy is used, maximum throughput is one transfer for every two clock cycles. When the DMACNTLn.DIR bit is 0, the first bus cycle reads data from the source using the ADCAn counter, while the second bus cycle writes the data into the destination using the ADCBn counter. When the DMACNTLn.DIR bit is set, the first bus cycle reads data from the source using the AD- CBn counter, while the second bus cycle writes the data into the destination addressed by the ADCAn counter. The number of bytes transferred in each cycle is taken from the DMACNTLn.TCS register bit. After the data item has been transferred, the BLTCn counter is decremented by one. The ADCAn and ADCBn counters are updated accord- ing to the INCA, INCB, ADA, and ADB fields in the DMACNTLn register.

9.3 OPERATION MODES

The DMAC operates in three different block transfer modes: single transfer, double buffer, and auto-initialize.

9.3.1 Single Transfer Operation

This mode provides the simplest way to accomplish a single block data transfer. Initialization 1. Write the block transfer addresses and byte count into the corresponding ADCAn, ADCBn, and BLTCn counters. 2. Clear the DMACNTLn.OT bit to select non-auto-initial- ize mode. Clear the DMASTAT.VLD bit by writing a 1 to it. 3. Set the DMACNTLn.CHEN bit to activate the channel and enable it to respond to DMA transfer requests. Termination When the BLTCn counter reaches 0: 1. The transfer operation terminates. 2. The DMAST AT.TC and DMAST AT.OVR bits are set, and the DMASTAT.CHAC bit is cleared. 3. An interrupt is generated if enabled by the DMACNTLn.ETC or DMACNTLn.EOVR bits. The DMACNTLn.CHEN bit must be cleared before loading the DMACNTLn register to avoid prematurely starting a new DMA transfer.

9.3.2 Double Buffer Operation

This mode allows software to set up the next block transfer while the current block transfer proceeds. Initialization 1. Write the block transfer addresses and byte count into the ADCAn, ADCBn, and BLTCn counters. 2. Clear the DMACNTLn.OT bit to select non-auto-initial- ize mode. Clear the DMASTAT.VLD bit by writing a 1 to it. 3. Set the DMACNTLn.CHEN bit. This activates the chan- nel and enables it to respond to DMA transfer requests. 4. While the current block transfer proceeds, write the ad- dresses and byte count for the next block into the ADRAn, ADRBn, and BLTRn registers. The BLTRn reg- ister must be written last, because it sets the DMAS- TAT .VLD bit which indicates that all the parameters for the next transfer have been updated. Continuation/Termination When the BLTCn counter reaches 0: 1. The DMASTAT.TC bit is set. 2. An interrupt is generated if enabled by the DMACNTLn.ETC bit. 3. The DMAC channel checks the value of the VLD bit. If the DMAST AT.VLD bit is set: 1. The channel copies the ADRAn, ADRBn, and BLTRn values into the ADCAn, ADCBn, and BLTCn registers. 2. The DMASTAT.VLD bit is cleared. 3. The next block transfer is started. Obsolete

43 www.national.com CP3BT23 If the DMAST AT.VLD bit is clear: 1. The transfer operation terminates. 2. The channel sets the DMASTAT.OVR bit. 3. The DMASTAT.CHAC bit is cleared. 4. An interrupt is generated if enabled by the DMACNTLn.EOVR bit. The DMACNTLn.CHEN bit must be cleared before loading the DMACNTLn register to avoid prematurely starting a new DMA transfer. Note: The ADCBn and ADRBn registers are used only in indirect (memory-to-memory) transfer. In direct (flyby) mode, the DMAC does not use them and therefore does not copy ADRBn into ADCBn.

9.3.3 Auto-Initialize Operation

This mode allows the DMAC to continuously fill the same memory area without software intervention. Initialization 1. Write the block addresses and byte count into the AD- CAn, ADCBn, and BLTCn counters, as well as the ADRAn, ADRBn, and BLTRn registers. 2. Set the DMACNTLn.OT bit to select auto-initialize mode. 3. Set the DMACNTLn.CHEN bit to activate the channel and enable it to respond to DMA transfer requests. Continuation When the BLTCn counter reaches 0: 1. The contents of the ADRAn, ADRBn, and BLTRn regis- ters are copied to the ADCAn, ADCBn, and BLTCn counters. 2. The DMAC channel checks the value of the DMAS- TAT.TC bit. If the DMAST AT.TC bit is set: 1. The DMASTAT.OVR bit is set. 2. A level interrupt is generated if enabled by the DMACNTLn.EOVR bit. 3. The operation is repeated. If the DMAST AT.TC bit is clear: 1. The DMASTAT.TC bit is set. 2. A level interrupt is generated if enabled by the DMACNTLn.ETC bit. 3. The DMAC operation is repeated. Termination The DMA transfer is terminated when the DMACNTLn.CHEN bit is cleared.

9.4 SOFTWARE DMA REQUEST

In addition to the hardware requests from I/O devices, a DMA transfer request can also be initiated by software. A software DMA transfer request must be used for block copy- ing between memory devices. When the DMACNTLn.SWRQ bit is set, the corresponding DMA channel receives a DMA transfer request. When the DMACNTLn.SWRQ bit is clear, the software DMA transfer request of the corresponding channel is inactive. For each channel, use the software DMA transfer request only when the corresponding hardware DMA request is in- active and no terminal count interrupt is pending. Software can poll the DMAST AT.CHAC bit to determine whether the DMA channel is already active. After verifying the DMAS- TATn.CHAC bit is clear (channel inactive), check the DMAS- TATn.TC (terminal count) bit. If the TC bit is clear, then no terminal count condition exists and therefore no terminal count interrupt is pending. If the channel is not active and no terminal count interrupt is pending, software may request a DMA transfer.

9.5 DEBUG MODE

When the FREEZE signal is active, all DMA operations are stopped. They will start again when the FREEZE signal goes inactive. This allows breakpoints to be used in debug systems.

9.6 DMA CONTROLLER REGISTER SET

There are four identical sets of DMA controller registers, as listed in T able 18. Table 18 DMA Controller Registers Name Address Description ADCA0 FF F800h Device A Address Counter Register ADRA0 FF F804h Device A Address Register ADCB0 FF F808h Device B Address Counter Register ADRB0 FF F80Ch Device B Address Register BLTC0 FF F810h Block Length Counter Register BLTR0 FF F814h Block Length Register DMACNTL0 FF F81Ch DMA Control Register DMASTAT0 FF F81Eh DMA Status Register ADCA1 FF F820h Device A Address Counter Register ADRA1 FF F824h Device A Address Register ADCB1 FF F828h Device B Address Counter Register ADRB1 FF F82Ch Device B Address Register BLTC1 FF F830h Block Length Counter Register BLTR1 FF F834h Block Length Register DMACNTL1 FF F83Ch DMA Control Register DMASTAT1 FF F83Eh DMA Status Register Obsolete

www.national.com 44 CP3BT23

9.6.1 Device A Address Counter Register (ADCAn)

The Device A Address Counter register is a 32-bit, read/ write register. It holds the current 24-bit address of either the source data item or the destination location, depending on the state of the DIR bit in the CNTLn register. The ADA bit of DMACNTLn register controls whether to adjust the point- er in the ADCAn register by the step size specified in the INCA field of DMACNTLn register. The upper 8 bits of the ADCAn register are reserved and always clear.

9.6.2 Device A Address Register (ADRAn)

The Device A Address register is a 32-bit, read/write regis- ter. It holds the 24-bit starting address of either the next source data block, or the next destination data area, according to the DIR bit in the DMACNTLn register. The upper 8 bits of the ADRAn register are reserved and always clear.

9.6.3 Device B Address Counter Register (ADCBn)

The Device B Address Counter register is a 32-bit, read/ write register. It holds the current 24-bit address of either the source data item, or the destination location, according to the DIR bit in the CNTLn register. The ADCBn register is up- dated after each transfer cycle by INCB field of the DMACNTLn register according to ADB bit of the DMACNTLn register. In direct (flyby) mode, this register is not used. The upper 8 bits of the ADCBn register are re- served and always clear.

9.6.4 Device B Address Register (ADRBn)

The Device B Address register is a 32-bit, read/write regis- ter. It holds the 24-bit starting address of either the next source data block or the next destination data area, accord- ing to the DIR bit in the CNTLn register. In direct (flyby) mode, this register is not used. The upper 8 bits of the AD- CRBn register are reserved and always clear.

9.6.5 Block Length Counter Register (BLTCn)

The Block Length Counter register is a 16-bit, read/write register. It holds the current number of DMA transfers to be executed in the current block. BLTCn is decremented by one after each transfer cycle. A DMA transfer may consist of 1 or 2 bytes, as selected by the DMACNTLn.TCS bit. Note: 0000h is interpreted as 216-1 transfer cycles. ADCA2 FF F840h Device A Address Counter Register ADRA2 FF F844h Device A Address Register ADCB2 FF F848h Device B Address Counter Register ADRB2 FF F84Ch Device B Address Register BLTC2 FF F850h Block Length Counter Register BLTR2 FF F854h Block Length Register DMACNTL2 FF F85Ch DMA Control Register DMASTAT2 FF F85Eh DMA Status Register ADCA3 FF F860h Device A Address Counter Register ADRA3 FF F864h Device A Address Register ADCB3 FF F868h Device B Address Counter Register ADRB3 FF F86Ch Device B Address Register BLTC3 FF F870h Block Length Counter Register BLTR3 FF F874h Block Length Register DMACNTL3 FF F87Ch DMA Control Register DMASTAT3 FF F87Eh DMA Status Register 31 24 23 0 Reserved Device A Address Counter Table 18 DMA Controller Registers Name Address Description 31 24 23 0 Reserved Device A Address 31 24 23 0 Reserved Device B Address Counter 31 24 23 0 Reserved Device B Address 15 0 Block Length Counter Obsolete

45 www.national.com CP3BT23

9.6.6 Block Length Register (BLTRn)

The Block Length register is a 16-bit, read/write register. It holds the number of DMA transfers to be performed for the next block. Writing this register automatically sets the DM- ASTAT.VLD bit. Note: 0000h is interpreted as 216-1 transfer cycles.

9.6.7 DMA Control Register (DMACNTLn)

The DMA Control register n is a word-wide, read/write reg- ister that controls the operation of DMA channel n. This reg- ister is cleared at reset. Reserved bits must be written with CHEN The Channel Enable bit must be set to enable any DMA operation on this channel. Writing a 1 to this bit starts a new DMA transfer even if it is currently a 1. If all DMACNTLn.CHEN bits are clear, the DMA clock is disabled to reduce power. – Channel disabled. 1 – Channel enabled. ETC If the Enable Interrupt on Terminal Count bit is set, it enables an interrupt when the DMAS- TAT .TC bit is set. – Interrupt disabled. 1 – Interrupt enabled. EOVR If the Enable Interrupt on OVR bit is set, it en- ables an interrupt when the DMASTAT .OVR bit is set. – Interrupt disabled. 1 – Interrupt enabled. TCS The Transfer Cycle Size bit specifies the num- ber of bytes transferred in each DMA transfer cycle. In direct (fly-by) mode, undefined re- sults occur if the TCS bit is not equal to the ad- dressed memory bus width. – Byte transfers (8 bits per cycle). 1 – Word transfers (16 bits per cycle). IND The Direct/Indirect Transfer bit specifies the transfer type. 0 – Direct transfer (flyby). 1 – Indirect transfer (memory-to-memory). DIR The Transfer Direction bit specifies the direc- tion of the transfer relative to Device A. 0 – Device A (pointed to by the ADCAn regis- ter) is the source. In Fly-By mode a read transaction is initialized. – Device A (pointed to by the ADCAn regis- ter) is the destination. In Fly-By mode a write transaction is initialized. OT The Operation Type bit specifies the operation mode of the DMA controller. – Single-buffer mode or double-buffer mode enabled. 1 – Auto-Initialize mode enabled. BPC The Bus Policy Control bit specifies the bus policy applied by the DMA controller. The op- eration mode can be either intermittent (cycle stealing) or continuous (burst). – Intermittent operation. The DMAC chan- nel relinquishes the bus after each trans- action, even if the request is still asserted. – Continuous operation. The DMAC chan- nel n uses the bus continuously as long as the request is asserted. This mode can only be used for software DMA requests. For hardware DMA requests, the BPC bit must be clear. SWRQ The Software DMA Request bit is written with a 1 to initiate a software DMA request. Writing a 0 to this bit deactivates the software DMA request. The SWRQ bit must only be written when the DMRQ signal for this channel is in- active (DMASTAT.CHAC = 0). – Software DMA request is inactive. 1 – Software DMA request is active. ADA If the Device A Address Control bit is set, it en- ables updating the Device A address. 0 – ADCAn address unchanged. 1 – ADCAn address incremented or decre- mented, according to INCA field of DMACNTLn register. INCA The Increment/Decrement ADCAn field spec- ifies the step size for the Device A address in- crement/decrement. 00 – Increment ADCAn register by 1. 01 – Increment ADCAn register by 2. 10 – Decrement ADCAn register by 1. 11 – Decrement ADCAn register by 2. ADB If the Device B Address Control bit is set, it en- ables updating the Device B Address. – ADCBn address unchanged. 1 – ADCBn address incremented or decre- mented, according to INCB field of DMACNTLn register. INCB The Increment/Decrement ADCBn field spec- ifies the step size for the Device B address in- crement/decrement. 00 – Increment ADCBn register by 1. 01 – Increment ADCBn register by 2. 10 – Decrement ADCBn register by 1. 11 – Decrement ADCBn register by 2. 15 0 Block Length 765432 1 0 BPC OT DIR IND TCS EOVR ETC CHEN 15 14 13 12 11 10 9 8 Res. INCB ADB INCA ADA SWRQ Obsolete

www.national.com 46 CP3BT23

9.6.8 DMA Status Register (DMASTAT)

The DMA status register is a byte-wide, read register that holds the status information for the DMA channel n. This register is cleared at reset. The reserved bits always return zero when read. The VLD, OVR and TC bits are sticky (once set by the occurrence of the specific condition, they remain set until explicitly cleared by software). These bits can be in- dividually cleared by writing 1 to the bit positions in the DM- ASTAT register to be cleared. Writing 0 to these bits has no effect TC The Terminal Count bit indicates whether the transfer was completed by a terminal count condition (BLTCn Register reached 0). – Terminal count condition did not occur. 1 – Terminal count condition occurred. OVR The behavior of the Channel Overrun bit de- pends on the operation mode (single buffer, double buffer, or auto-initialize) of the DMA channel. In double-buffered mode (DMACNTLn.OT = 0): The OVR bit is set when the present transfer is completed (BLTCn = 0), but the parameters for the next transfer (address and block length) are not valid (DMASTAT .VLD = 0). In auto-initialize mode (DMACNTLn.OT = 1): The OVR bit is set when the present transfer is completed (BLTCn = 0), and the DMAS- TAT .TC bit is still set. In single-buffer mode: Operates in the same way as double-buffer mode. In single-buffered mode, the DMAS- TAT .VLD bit should always be clear, so it will also be set when the DMASTAT.TC bit is set. Therefore, the OVR bit can be ignored in this mode. CHAC The Channel Active bit continuously indicates the active or inactive status of the channel, and therefore, it is read only. Data written to the CHAC bit is ignored. – Channel inactive. 1 – Indicates that the channel is active (CHEN bit in the CNTLn register is 1 and BLTCn > 0) VLD The Transfer Parameters Valid bit specifies whether the transfer parameters for the next block to be transferred are valid. Writing the BLTRn register automatically sets this bit. The bit is cleared in the following cases: ! The present transfer is completed and the ADRAn, ADRBn (indirect mode only), and BLTR registers are copied to the ADCAn, ADCBn (indirect mode only), and BLTCn registers. ! Writing 1 to the VLD bit. 7 4 3 2 1 0 Reserved VLD CHAC OVR TC Obsolete

47 www.national.com CP3BT23

10.0 Interrupts

The Interrupt Control Unit (ICU) receives interrupt requests from internal and external sources and generates interrupts to the CPU. Interrupts from the timers, UARTs, Microwire/ SPI interface, and Multi-Input Wake-Up module are all maskable interrupts. The highest-priority interrupt is the Non-Maskable Interrupt (NMI), which is triggered by a falling edge received on the NMI input pin. The priorities of the maskable interrupts are hardwired and therefore fixed. The implemented interrupts are named IRQ0 through IRQ47, in which IRQ0 has the lowest priority and IRQ47 has the highest priority. (IRQ0 is not implement- ed, so IRQ1 is the lowest priority interrupt that normally may occur.)

10.1 NON-MASKABLE INTERRUPTS

The Interrupt Control Unit (ICU) receives the external NMI input and generates the NMI signal driven to the CPU. The NMI input is an asynchronous input with Schmitt trigger characteristics and an internal synchronization circuit, therefore no external synchronizing circuit is needed. The NMI pin triggers an exception on its falling edge.

10.1.1 Non-Maskable Interrupt Processing

The CPU performs an interrupt acknowledge bus cycle when beginning to process a non-maskable interrupt. At reset, NMI interrupts are disabled and must remain dis- abled until software initializes the interrupt table, interrupt base register (INTBASE), and the interrupt mode. The ex- ternal NMI interrupt is enabled by setting the EXNMI.EN- LCK bit and will remain enabled until a reset occurs. Alternatively, the external NMI interrupt can be enabled by setting the EXNMI.EN bit and will remain enabled until an in- terrupt event or a reset occurs.

10.2 MASKABLE INTERRUPTS

The ICU receives level-triggered interrupt request signals from 47 sources and generates a vectored interrupt to the CPU when required. Priority among the implemented inter- rupt sources (named IRQ1 through IRQ47) is fixed. The maskable interrupts are globally enabled and disabled by the E bit in the PSR register. The EI and DI instructions are used to set (enable) and clear (disable) this bit. The glo- bal maskable interrupt enable bit (I bit in the PSR) must also be set before any maskable interrupts are taken. Each interrupt source can be individually enabled or dis- abled under software control through the ICU interrupt en- able registers and also through interrupt enable bits in the peripherals that request the interrupts. The ICU supports IRQ0, but in the CP3BT23 it is not connected to any inter- rupt source.

10.2.1 Maskable Interrupt Processing

Interrupt vector numbers are always positive, in the range 10h to 3Fh. The IVCT register contains the interrupt vector of the enabled and pending interrupt with the highest priori- ty. The interrupt vector 10h corresponds to IRQ0 and the lowest priority, while the vector 3Fh corresponds to IRQ47 and the highest priority. The CPU performs an interrupt ac- knowledge bus cycle on receiving a maskable interrupt re- quest from the ICU. During the interrupt acknowledge cycle, a byte is read from address FF FE00h (IVCT register). The byte is used as an index into the Dispatch Table to deter- mine the address of the interrupt handler. Because IRQ0 is not connected to any interrupt source, it would seem that the interrupt vector would never return the value 10h. If it does return a value of 10h, the entry in the dispatch table should point to a default interrupt handler that handles this error condition. One possible condition for this to occur is deassertion of the interrupt before the interrupt acknowledge cycle.

10.3 INTERRUPT CONTROLLER REGISTERS

Table 19 lists the ICU registers. Table 19 Interrupt Controller Registers Name Address Description IVCT FF FE00h Interrupt Vector Register NMISTAT FF FE02h Non-Maskable Interrupt Status Register EXNMI FF FE04h External NMI Trap Control and Status Register ISTA T0 FF FE0Ah Interrupt Status Register 0 ISTA T1 FF FE0Ch Interrupt Status Register 1 ISTA T2 FF FE20h Interrupt Status Register 2 IENAM0 FF FE0Eh Interrupt Enable and Mask Register 0 IENAM1 FF FE10h Interrupt Enable and Mask Register 1 IENAM2 FF FE22h Interrupt Enable and Mask Register 2 Obsolete

www.national.com 48 CP3BT23

10.3.1 Interrupt Vector Register (IVCT)

The IVCT register is a byte-wide read-only register which re- ports the encoded value of the highest priority maskable in- terrupt that is both asserted and enabled. The valid range is from 10h to 3Fh. The register is read by the CPU during an interrupt acknowledge bus cycle, and INTVECT is valid dur- ing that time. It may contain invalid data while INTVECT is updated. INTVECT The Interrupt Vector field indicates the highest priority interrupt which is both asserted and enabled.

10.3.2 Non-Maskable Interrupt Status Register

(NMISTAT) The NMISTAT register is a byte-wide read-only register. It holds the status of the current pending Non-Maskable Inter- rupt (NMI) requests. On the CP3BT23, the external NMI in- put is the only source of NMI interrupts. The NMISTAT register is cleared on reset and each time its contents are read. EXT The External NMI request bit indicates wheth- er an external non-maskable interrupt request has occurred. Refer to the description of the EXNMI register below for additional details. – No external NMI request. 1 – External NMI request has occurred.

10.3.3 External NMI Trap Control and Status Register

(EXNMI) The EXNMI register is a byte-wide read/write register. It in- dicates the current value of the NMI pin and controls the NMI interrupt trap generation based on a falling edge of the NMI pin. TST , EN and ENLCK are cleared on reset. When writing to this register, all reserved bits must be written with 0 for the device to function properly EN The EXNMI trap enable bit is one of two bits that can be used to enable NMI interrupts. The bit is cleared by hardware at reset and whenever the NMI interrupt occurs (EXN- MI.EXT set). It is intended for applications where the NMI input toggles frequently but nested NMI traps are not desired. For these applications, the EN bit needs to be re-en- abled before exiting the trap handler. When used this way, the ENLCK bit should never be set. The EN bit can be set and cleared by soft- ware (software can set this bit only if EXN- MI.EXT is cleared), and should only be set after the interrupt base register and the inter- rupt stack pointer have been set up. – NMI interrupts not enabled by this bit (but may be enabled by the ENLCK bit). – NMI interrupts enabled. PIN The PIN bit indicates the state (non-inverted) on the NMI input pin. This bit is read-only, data written into it is ignored. – NMI pin not asserted. 1 – NMI pin asserted. ENLCK The EXNMI trap enable lock bit is used to per- manently enable NMI interrupts. Only a de- vice reset can clear the ENLCK bit. This allows the external NMI feature to be enabled after the interrupt base register and the inter- rupt stack pointer have been set up. When the ENLCK bit is set, the EN bit is ignored. – NMI interrupts not enabled by this bit (but may be enabled by the EN bit). – NMI interrupts enabled. 7 6 5 0 0 0 INTVECT 71 0 Reserved EXT 73 2 1 0 Reserved ENLCK PIN EN Obsolete

49 www.national.com CP3BT23

10.3.4 Interrupt Enable and Mask Register 0 (IENAM0)

The IENAM0 register is a word-wide read/write register which holds bits that individually enable and disable the maskable interrupt sources IRQ1 through IRQ15. The reg- ister is initialized to FFFFh at reset. IENA Each Interrupt Enable bit enables or disables the corresponding interrupt request IRQ1 through IRQ15, for example IENA15 controls IRQ15. Because IRQ0 is not used, IENA0 is ignored. – Interrupt is disabled. 1 – Interrupt is enabled.

10.3.5 Interrupt Enable and Mask Register 1 (IENAM1)

The IENAM1 register is a word-wide read/write register which holds bits that individually enable and disable the maskable interrupt sources IRQ16 through IRQ31. The reg- ister is initialized to FFFFh at reset. IENA Each Interrupt Enable bit enables or disables the corresponding interrupt request IRQ16 through IRQ31, for example IENA31 controls IRQ31. – Interrupt is disabled. 1 – Interrupt is enabled.

10.3.6 Interrupt Enable and Mask Register 2 (IENAM2)

The IENAM2 register is a word-wide read/write register which holds bits that individually enable and disable the maskable interrupt sources IRQ32 through IRQ47. The reg- ister is initialized to FFFFh at reset. IENA Each Interrupt Enable bit enables or disables the corresponding interrupt request IRQ32 through IRQ47, for example IENA47 controls IRQ47. – Interrupt is disabled. 1 – Interrupt is enabled.

10.3.7 Interrupt Status Register 0 (ISTAT0)

The ISTAT0 register is a word-wide read-only register. It in- dicates which maskable interrupt inputs to the ICU are ac- tive. These bits are not affected by the state of the corresponding IENA bits. IST The Interrupt Status bits indicate if a maskable interrupt source is signalling an in- terrupt request. IST15:1 correspond to IRQ15 to IRQ1 respectively. Because the IRQ0 inter- rupt is not used, bit 0 always reads back 0. – Interrupt is not active. 1 – Interrupt is active.

10.3.8 Interrupt Status Register 1 (ISTAT1)

The ISTAT1 register is a word-wide read-only register. It in- dicates which maskable interrupt inputs into the ICU are ac- tive. These bits are not affected by the state of the corresponding IENA bits. IST The Interrupt Status bits indicate if a maskable interrupt source is signalling an in- terrupt request. IST31:16 correspond to IRQ31 to IRQ16, respectively. – Interrupt is not active. 1 – Interrupt is active.

10.3.9 Interrupt Status Register 2 (ISTAT2)

The ISTAT2 register is a word-wide read-only register. It in- dicates which maskable interrupt inputs into the ICU are ac- tive. These bits are not affected by the state of the corresponding IENA bits. IST The Interrupt Status bits indicate if a maskable interrupt source is signalling an in- terrupt request. IST47:32 correspond to IRQ47 to IRQ32, respectively. – Interrupt is not active. 1 – Interrupt is active. 15 1 0 IENA Res. 15 0 IENA 15 0 IENA 15 1 0 IST Res. 15 0 IST 15 0 IST Obsolete

www.national.com 50 CP3BT23

10.4 MASKABLE INTERRUPT SOURCES

Table 20 shows the interrupts assigned to various on-chip maskable interrupts. The priority of simultaneous maskable interrupts is linear, with IRQ47 having the highest priority. Table 20 Maskable Interrupts Assignment All reserved interrupt vectors should point to default or error interrupt handlers.

10.5 NESTED INTERRUPTS

Nested NMI interrupts are always enabled. Nested maskable interrupts are disabled by default, however an in- terrupt handler can allow nested maskable interrupts by set- ting the I bit in the PSR. The LPR instruction is used to set the I bit. Nesting of specific maskable interrupts can be allowed by disabling interrupts from sources for which nesting is not al- lowed, before setting the I bit. Individual maskable interrupt sources can be disabled using the IENAM0 and IENAM1 registers. Any number of levels of nested interrupts are allowed, limit- ed only by the available memory for the interrupt stack. IRQ Number Description IRQ47 TWM (Timer 0) IRQ46 Bluetooth LLC 0 IRQ45 Bluetooth LLC 1 IRQ44 Bluetooth LLC 2 IRQ43 Bluetooth LLC 3 IRQ42 Bluetooth LLC 4 IRQ41 Bluetooth LLC 5 IRQ40 Reserved IRQ39 DMA Channel 0 IRQ38 DMA Channel 1 IRQ37 DMA Channel 2 IRQ36 DMA Channel 3 IRQ35 CAN0 IRQ34 Advanced Audio Interface (AAI) IRQ33 UART0 RX IRQ32 CVSD/PCM Converter IRQ31 ACCESS.bus IRQ30 T A (Timer input A) IRQ29 TB (Timer input B) IRQ28 VTUA (VTU Interrupt Request 1) IRQ27 VTUB (VTU Interrupt Request 2) IRQ26 VTUC (VTU Interrupt Request 3) IRQ25 VTUD (VTU Interrupt Request 4) IRQ24 Microwire/SPI RX/TX IRQ23 UART0 TX IRQ22 UART0 CTS IRQ21 CAN1 IRQ20 UART1 RX IRQ19 UART1 TX IRQ18 UART2 RX IRQ17 UART2 TX IRQ16 UART3 RX IRQ15 UART3 TX IRQ14 Reserved IRQ13 ADC (Done) IRQ12 MIWU Interrupt 0 IRQ11 MIWU Interrupt 1 IRQ10 MIWU Interrupt 2 IRQ9 MIWU Interrupt 3 IRQ8 MIWU Interrupt 4 IRQ7 MIWU Interrupt 5 IRQ6 MIWU Interrupt 6 IRQ5 MIWU Interrupt 7 IRQ4 Reserved IRQ3 Random Number Generator (RNG) IRQ2 Reserved IRQ1 Flash Program/Data Memory IRQ0 Reserved IRQ Number Description Obsolete

11.0 Triple Clock and Reset

clocks, and a 32-kHz oscillator start-up delay. Figure 4. Triple Clock and Reset Module

11.1 EXTERNAL CRYSTAL NETWORK

ponents different from the ones specified in this datasheet. Figure 5. Main Clock External Crystal Network Figure 6. Slow Clock External Crystal Network

12 MHz

12 MHz ± 20 ppm

53 www.national.com CP3BT23 Choose capacitor component values in the tables to obtain the specified load capacitance for the crystal when com- bined with the parasitic capacitance of the trace, socket, and package (which can vary from 0 to 8 pF). As a guideline, the load capacitance is: C2 > C1 C1 can be trimmed to obtain the desired load capacitance. The start-up time of the 32.768 kHz oscillator can vary from one to six seconds. The long start-up time is due to the high Q value and high serial resistance of the crystal necessary to minimize power consumption in Power Save mode.

11.2 MAIN CLOCK

The Main Clock is generated by the 12-MHz high-frequency oscillator or driven by an external signal (typically the LMX5252 RF chip). It can be stopped by the Power Man- agement Module to reduce power consumption during peri- ods of reduced activity. When the Main Clock is restarted, a 14-bit timer generates a Good Main Clock signal after a start-up delay of 32,768 clock cycles. This signal is an indi- cator that the high-frequency oscillator is stable. The Stop Main Osc signal from the Power Management Module stops and starts the high-frequency oscillator. When this signal is asserted, it presets the 14-bit timer to 3FFFh and stops the high-frequency oscillator. When the signal goes inactive, the high-frequency oscillator starts and the 14-bit timer counts down from its preset value. When the timer reaches zero, it stops counting and asserts the Good Main Clock signal.

11.3 SLOW CLOCK

The Slow Clock is necessary for operating the device in re- duced power modes and to provide a clock source for mod- ules such as the Timing and Watchdog Module. The Slow Clock operates in a manner similar to the Main Clock. The Stop Slow Osc signal from the Power Manage- ment Module stops and starts the low-frequency (32.768 kHz) oscillator. When this signal is asserted, it presets a 6- bit timer to 3Fh and disables the low-frequency oscillator. When the signal goes inactive, the low-frequency oscillator starts, and the 6-bit timer counts down from its preset value. When the timer reaches zero, it stops counting and asserts the Good Slow Clock signal, which indicates that the Slow Clock is stable. For systems that do not require a reduced power consump- tion mode, the external crystal network may be omitted for the Slow Clock. In that case, the Slow Clock can be synthe- sized by dividing the Main Clock by a prescaler factor. The prescaler circuit consists of a fixed divide-by-2 counter and a programmable 8-bit prescaler register. This allows a choice of clock divisors ranging from 2 to 512. The resulting Slow Clock frequency must not exceed 100 kHz. A software-programmable multiplexer selects either the prescaled Main Clock or the 32.768 kHz oscillator as the Slow Clock. At reset, the prescaled Main Clock is selected, ensuring that the Slow Clock is always present initially. Se- lection of the 32.768 kHz oscillator as the Slow Clock dis- ables the clock prescaler, which allows the CLK1 oscillator to be turned off, which reduces power consumption and ra- diated emissions. This can be done only if the module de- tects a toggling low-speed oscillator. If the low-speed oscillator is not operating, the prescaler remains available as the Slow Clock source.

11.4 PLL CLOCK

The PLL Clock is generated by the PLL from the 12 MHz Main Clock by applying a multiplication factor of ×3, ×4, or ×5. To enable the PLL: 1. Set the PLL multiplication factor in PRFSC.MODE. 2. Clear the PLL power-down bit CRCTRL.PLLPWD. 3. Clear the high-frequency clock select bit CRC- TRL.FCLK. 4. Read CRCTRL.FCLK, and go back to step 3 if not clear. The CRCTRL.FCLK bit will be clear only after the PLL has stabilized, so software must repeat step 3 until the bit is clear. The clock source can be switched back to the Main Clock by setting the CRCTRL.FCLK bit. The PRSFC register must not be modified while the System Clock is derived from the PLL Clock. The System Clock must be derived from the low-frequency oscillator clock while the MODE field is modified. Table 22 Component Values of the Low Frequency Crystal Circuit Component Parameters Values Tolerance Crystal Resonance Frequency Type Maximum Serial Resistance Maximum Shunt Capacitance Load Capacitance Min. Q factor 32.768 kHz Parallel N-Cut or XY -bar 40 kΩ 2 pF 12.5 pF 40000 N/A Capacitor C1, C2 Capacitance 25 pF 20% CL C1 C2× Obsolete

11.5 SYSTEM CLOCK

11.6 AUXILIARY CLOCKS

11.7 POWER-ON RESET

which is the best-case scenario.

1. After both of these supply voltage rails have met this

levels specified in the DC Characteristics.

1. The RESET pin must then be held low until the Main

Figure 7. Power-On Reset Timing

11.8 EXTERNAL RESET

External reset is triggered by assertion of the RESET input.

11.8.1 Simple External Reset

Figure 8. Simple External Reset

11.8.2 Manual and SDI External Reset

for a CP3BT23 device operating from an IOVCC at 3.3V. Figure 9. Manual and SDI External Reset plemented, an LM3722 with active pullup may be used.

11.8.3 Fault-Tolerant External Reset

IOVCC supply and an external watchdog timer. Figure 10. Fault-Tolerant External Reset Core VCC—the 2.5V power supply rail for the core logic. ! IOVCC —the 2.5–3.3V power supply rail for the I/O logic. LM3710 but without the watchdog timer. RESET — an active-low reset signal to the CP3BT23. to a separate interrupt input. system shutdown functions before being placed into reset.

www.national.com 56 CP3BT23

11.9 CLOCK AND RESET REGISTERS

Table 23 lists the clock and reset registers.

11.9.1 Clock and Reset Control Register (CRCTRL)

The CRCTRL register is a byte-wide read/write register that controls the clock selection and contains the power-on reset status bit. At reset, the CRCTRL register is initialized as de- scribed below: SCLK The Slow Clock Select bit controls the clock source used for the Slow Clock. – Slow Clock driven by prescaled Main Clock. – Slow Clock driven by 32.768 kHz oscilla- tor. FCLK The Fast Clock Select bit selects between the

12 MHz Main Clock and the PLL as the source

used for the System Clock. After reset, the Main Clock is selected. Attempting to switch to the PLL while the PLLPWD bit is set (PLL is turned off) is ignored. Attempting to switch to the PLL also has no effect if the PLL output clock has not stabilized. – The System Clock prescaler is driven by the output of the PLL. – The System Clock prescaler is driven by the 12-MHz Main Clock. This is the de- fault after reset. PLLPWD The PLL Power-Down bit controls whether the PLL is active or powered down (Stop PLL sig- nal asserted). When this bit is set, the on-chip PLL stays powered-down. Otherwise it is pow- ered-up or it can be controlled by the Power Management Module, respectively. Before software can power-down the PLL in Active mode by setting the PLLPWD bit, the FCLK bit must be set. Attempting to set the PLLPWD bit while the FCLK bit is clear is ignored. The FCLK bit cannot be cleared until the PLL clock has stabilized. After reset this bit is set. – PLL is active. 1 – PLL is powered down. ACE1 When the Auxiliary Clock Enable bit is set and a stable Main Clock is provided, the Auxiliary Clock 1 prescaler is enabled and generates the first Auxiliary Clock. When the ACE1 bit is clear or the Main Clock is not stable, Auxiliary Clock 1 is stopped. Auxiliary Clock 1 is used as the clock input for the Bluetooth LLC and the Advanced Audio Interface. After reset this bit is clear. – Auxiliary Clock 1 is stopped. 1 – Auxiliary Clock 1 is active if the Main Clock is stable. ACE2 When the Auxiliary Clock Enable 2 bit is set and a stable Main Clock is provided, the Aux- iliary Clock 2 prescaler is enabled and gener- ates Auxiliary Clock 2. When the ACE2 bit is clear or the Main Clock is not stable, the Aux- iliary Clock 2 is stopped. Auxiliary Clock 2 is used as the clock input for the CVSD/PCM transcoder and the A/D converter. After reset this bit is clear. – Auxiliary Clock 2 is stopped. 1 – Auxiliary Clock 2 is active if the Main Clock is stable. POR The Power-On-Reset bit is set when a power- turn-on condition has been detected. This bit can only be cleared by software, not set. Writ- ing a 1 to this bit will be ignored, and the pre- vious value of the bit will be unchanged. – Software cleared this bit. 1 – Software has not cleared his bit since the last reset. Table 23 Clock and Reset Registers Name Address Description CRCTRL FF FC40h Clock and Reset Control Register PRSFC FF FC42h High Frequency Clock Prescaler Register PRSSC FF FC44h Low Frequency Clock Prescaler Register PRSAC FF FC46h Auxiliary Clock Prescaler Register 7 6 5 4 3 2 1 0 Reserved POR ACE2 ACE1 PLLPWD FCLK SCLK Obsolete

57 www.national.com CP3BT23

11.9.2 High Frequency Clock Prescaler Register

(PRSFC) The PRSFC register is a byte-wide read/write register that holds the 4-bit clock divisor used to generate the high-fre- quency clock. In addition, the upper three bits are used to control the operation of the PLL. The register is initialized to 4Fh at reset (except in PROG mode FCDIV The Fast Clock Divisor specifies the divisor used to obtain the high-frequency System Clock from the PLL or Main Clock. The divisor is (FCDIV + 1). MODE The PLL MODE field specifies the operation mode of the on-chip PLL. After reset the MODE bits are initialized to 100b, so the PLL is configured to generate a 48-MHz clock. This register must not be modified when the System Clock is derived from the PLL Clock. The System Clock must be derived from the low-frequency oscillator clock while the MODE field is modified.

11.9.3 Low Frequency Clock Prescaler Register

(PRSSC) The PRSSC register is a byte-wide read/write register that holds the clock divisor used to generate the Slow Clock from the Main Clock. The register is initialized to B6h at reset. SCDIV The Slow Clock Divisor field specifies a divi- sor to be used when generating the Slow Clock from the Main Clock. The Main Clock is divided by a value of (2 × (SCDIV + 1)) to ob- tain the Slow Clock. At reset, the SCDIV reg- ister is initialized to B6h, which generates a Slow Clock rate of 32786.885 Hz. This is about 0.5% faster than a Slow Clock generat- ed from an external 32768 Hz crystal network.

11.9.4 Auxiliary Clock Prescaler Register (PRSAC)

The PRSAC register is a byte-wide read/write register that holds the clock divisor values for prescalers used to gener- ate the two auxiliary clocks from the Main Clock. The regis- ter is initialized to FFh at reset. ACDIV1 The Auxiliary Clock Divisor 1 field specifies the divisor to be used for generating Auxiliary Clock 1 from the Main Clock. The Main Clock is divided by a value of (ACDIV1 + 1). ACDIV2 The Auxiliary Clock Divisor 2 field specifies the divisor to be used for generating Auxiliary Clock 2 from the Main Clock. The Main Clock is divided by a value of (ACDIV2 + 1). 7 6 4 3 0 Res MODE FCDIV MODE2:0 Output Frequency (from 12 MHz input clock)

Description

000 Reserved Reserved

001 Reserved Reserved

010 Reserved Reserved

011 36 MHz 3× Mode 100 48 MHz 4× Mode 101 60 MHz 5× Mode

110 Reserved Reserved

111 Reserved Reserved

www.national.com 58 CP3BT23

12.0 Power Management

The Power Management Module (PMM) improves the effi- ciency of the CP3BT23 by changing the operating mode (and therefore the power consumption) according to the re- quired level of device activity. The device implements four power modes: ! Active ! Power Save ! Idle ! Halt Table 24 summarizes the differences between power modes: the state of the high-frequency oscillator (on or off), the System Clock source (clock used by most modules), and the clock source used by the Timing and Watchdog Module (TWM). The high-frequency oscillator generates the 12-MHz Main Clock, and the low-frequency oscillator gener- ates a 32.768 kHz clock. The Slow Clock can be driven by the 32.768 kHz clock or a scaled version of the Main Clock. The low-frequency oscillator continues to operate in all four modes and power must be provided continuously to the de- vice power supply pins. In Halt mode, however, Slow Clock does not toggle, and as a result, the TWM timer and Watch- dog Module do not operate. For the Power Save and Idle modes, the high-frequency oscillator can be turned on or off under software control, as long as the low-frequency oscil- lator is used to drive Slow Clock. Table 25 shows the clock sources used by the CP3BT23 de- vice modules and their behavior in each power mode. * The Analog/Digital Converter (ADC) module is not auto- matically disabled by entering Halt mode, however its clock is stopped so no conversions may be performed in Halt mode. For maximum power savings, software must disable the ADC module before entering Halt mode. A module shown as On/Off in Table 25 may be enabled or disabled by software. A module shown as Active continues to operate even while its clock is suspended, which allows wake-up events to be processed during Idle and Halt modes. The Random Number Generator (RNG) module has two os- cillators which operate independently of the rest of the sys- tem. For maximum power savings, software must disable these oscillators.

12.1 ACTIVE MODE

In Active mode, the high-frequency oscillator is active and generates the 12-MHz Main Clock. The 32.768 kHz oscilla- tor is active and may be used to generate the Slow Clock. The PLL can be active or inactive, as required. Most on-chip modules are driven by the System Clock. The System Clock can be the PLL Clock after a programmable divider or the 12-MHz Main Clock. The activity of peripheral modules is controlled by their enable bits. Power consumption can be reduced in this mode by selec- tively disabling modules and by executing the WAIT instruc- tion. When the WAIT instruction is executed, the CPU stops executing new instructions until it receives an interrupt sig- nal. After reset, the CP3BT23 is in Active Mode.

12.2 POWER SAVE MODE

In Power Save mode, Slow Clock is used as the System Clock which drives the CPU and most on-chip modules. If Slow Clock is driven by the 32.768 kHz oscillator and no on- chip module currently requires the 12-MHz Main Clock, soft- ware can disable the high-frequency oscillator to further re- duce power consumption. Auxiliary Clocks 1 and 2 can be turned off under software control before switching to a re- duced power mode, or they may remain active as long as Main Clock is also active. If the system does not require the PLL output clock, the PLL can be disabled. Alternatively, the Main Clock and the PLL can also be controlled by the Hard- ware Clock Control function, if enabled. The clock architec- ture is described in Section 11.0. The Bluetooth LLC can either be switched to the 32 kHz clock internally in the module, or it remains running off Aux- iliary clock 1 as long as the Main Clock and Auxiliary Clock 1 are enabled. In Power Save mode, some modules are disabled or their operation is restricted. Other modules, including the CPU, continue to function normally, but operate at a reduced clock rate. Details of each module’s activity in Power Save mode are described in each module’s descriptions. It is recommended to keep CPU activity at a minimum by ex- ecuting the WAIT instruction to guarantee low power con- sumption in the system. Table 24 Power Mode Operating Summary Mode High-Frequency Oscillator System Clock TWM Clock Active On Main Clock Slow Clock Power Save On or Off Slow Clock Slow Clock Idle On or Off None Slow Clock Halt Off None None Table 25 Module Activity Summary Module Power Mode Clock SourceActive Power Save Idle Halt CPU On On/Off Off Off System MIWU On On Active Active System PMM On On On Active Slow Clock T W M O nO nO nO f f S l o w C l o c k Bluetooth On/Off On/Off On/Off Off Aux 1 Clock AAI On/Off On/Off On/Off Off Aux 1 Clock CVSD/PCM On/Off On/Off On/Off Off Aux 2 Clock ADC On/Off On/Off On/Off Off* Aux 2 Clock All Others On/Off On/Off Off Off System Obsolete

59 www.national.com CP3BT23

12.3 IDLE MODE

In Idle mode, the System Clock is disabled and therefore the clock is stopped to most modules of the device. The PLL and the high-frequency oscillator may be disabled as con- trolled by register bits. The low-frequency oscillator remains active. The Power Management Module (PMM) and the Timing and Watchdog Module (TWM) continue to operate off the Slow Clock. Auxiliary Clocks 1 and 2 can be turned off under software control before switching to a power sav- ing mode, or they remain active as long as Main Clock is also active. Alternatively, the 12 MHz Main Clock and the PLL can also be controlled by the Hardware Clock Control function, if enabled. The Bluetooth LLC can either be switched to the Slow Clock internally in the module or it remains running off the Auxilia- ry Clock 1 as long as the Main Clock and Auxiliary Clock 1 are enabled.

12.4 HALT MODE

In Halt mode, all the device clocks, including the System Clock, Main Clock, and Slow Clock, are disabled. The high- frequency oscillator and PLL are turned off. The low-fre- quency oscillator continues to operate, however its circuitry is optimized to guarantee lowest possible power consump- tion. This mode allows the device to reach the absolute min- imum power consumption without losing its state (memory, registers, etc.).

12.5 HARDWARE CLOCK CONTROL

The Hardware Clock Control (HCC) mechanism gives the Bluetooth Lower Link Controller (LLC) individual control over the high-frequency oscillator and the PLL. The Blue- tooth LLC can enter a Sleep mode for a specified number of low-frequency clock cycles. While the Bluetooth LLC is in Sleep mode and the CP3BT23 is in Power Save or Idle mode, the HCC mechanism may be used to control whether the high-frequency oscillator, PLL, or both units are dis- abled. Altogether, three mechanisms control whether the high-fre- quency oscillator is active, and four mechanisms control whether the PLL is active: ! HCC Bits: The HCCM and HCCH bits in the PMMCR register may be used to disable the high-frequency oscil- lator and PLL, respectively, in Power Save and Idle modes when the Bluetooth LLC is in Sleep mode. ! Disable Bits: The DMC and DHC bits in the PMMCR register may be used to disable the high-frequency oscil- lator and PLL, respectively, in Power Save and Idle modes. When used to disable the high-frequency oscilla- tor or PLL, the DMC and DHC bits override the HCC mechanism. ! Power Management Mode: Halt mode disables the high-frequency oscillator and PLL. Active Mode enables them. The DMC and DHC bits and the HCC mechanism have no effect in Active or Halt mode. ! PLL Power Down Bit: The PLLPWD bit in the CRCTRL register can be used to disable the PLL in all modes. This bit does not affect the high-frequency oscillator.

12.6 POWER MANAGEMENT REGISTERS

Table 26 lists the power management registers.

12.6.1 Power Management Control Register (PMMCR)

The Power Management Control/Status Register (PMMCR) is a byte-wide, read/write register that controls the operating power mode (Active, Power Save, Idle, or Halt) and enables or disables the high-frequency oscillator in the Power Save and Idle modes. At reset, the non-reserved bits of this reg- ister are cleared. The format of the register is shown below. PSM If the Power Save Mode bit is clear and the WBPSM bit is clear, writing 1 to the PSM bit causes the device to start the switch to Power Save mode. If the WBPSM bit is set when the PSM bit is written with 1, entry into Power Save mode is delayed until execution of a WAIT instruction. The PSM bit becomes set after the switch to Power Save mode is com- plete. The PSM bit can be cleared by soft- ware, and it can be cleared by hardware when a hardware wake-up event is detected. – Device is not in Power Save mode. 1 – Device is in Power Save mode. IDLE The Idle Mode bit indicates whether the de- vice has entered Idle mode. The WBPSM bit must be set to enter Idle mode. When the IDLE bit is written with 1, the device enters IDLE mode at the execution of the next WAIT instruction. The IDLE bit can be set and cleared by software. It is also cleared by the hardware when a hardware wake-up event is detected. – Device is not in Idle mode. 1 – Device is in Idle mode. Table 26 Power Management Registers Name Address Description PMMCR FF FC60h Power Management Control Register PMMSR FF FC62h Power Management Status Register 7 6 5 4 3 2 1 0 HCCH HCCM DHC DMC WBPSM HALT IDLE PSM Obsolete

www.national.com 60 CP3BT23 HALT The Halt Mode bit indicates whether the de- vice is in Halt mode. Before entering Halt mode, the WBPSM bit must be set. When the HALT bit is written with 1, the device enters the Halt mode at the execution of the next WAIT instruction. When in HALT mode, the PMM stops the System Clock and then turns off the PLL and the high-frequency oscillator. The HALT bit can be set and cleared by soft- ware. The Halt mode is exited by a hardware wake-up event. When this signal is set high, the oscillator is started. After the oscillator has stabilized, the HALT bit is cleared by the hard- ware. – Device is not in Halt mode. 1 – Device is in Halt mode. WBPSM When the Wait Before Power Save Mode bit is clear, a switch from Active mode to Power Save mode only requires setting the PSM bit. When the WBPSM bit is set, a switch from Ac- tive mode to Power Save, Idle, or Halt mode is performed by setting the PSM, IDLE or HALT bit, respectively, and then executing a WAIT instruction. Also, if the DMC or DHC bits are set, the high-frequency oscillator and PLL may be disabled only after a WAIT instruction is executed and the Power Save, Idle, or Halt mode is entered. – Mode transitions may occur immediately. 1 – Mode transitions are delayed until the next WAIT instruction is executed. DMC The Disable Main Clock bit may be used to disable the high-frequency oscillator in Power Save and Idle modes. In Active mode, the high-frequency oscillator is enabled without regard to the DMC value. In Halt mode, the high-frequency oscillator is disabled without regard to the DMC value. The DMC bit is cleared by hardware when a hardware wake- up event is detected. – High-frequency oscillator is only disabled in Halt mode or when disabled by the HCC mechanism. 1 – High-frequency oscillator is also disabled in Power Save and Idle modes. DHC The Disable High-Frequency (PLL) Clock bit and the CRCTRL.PLLPWD bit may be used to disable the PLL in Power Save and Idle modes. When the DHC bit is clear (and PLL- PWD = 0), the PLL is enabled in these modes. If the DHC bit is set, the PLL is disabled in Power Save and Idle mode. In Active mode with the CRCTRL.PLLPWD bit set, the PLL is enabled without regard to the DHC value. In Halt mode, the PLL is disabled without regard to the DMC value. The DHC bit is cleared by hardware when a hardware wake-up event is detected. – PLL is disabled only by entering Halt mode or setting the CRCTRL.PLLPWD bit. 1 – PLL is also disabled in Power Save or Idle mode. HCCM The Hardware Clock Control for Main Clock bit may be used in Power Save and Idle modes to disable the high-frequency oscillator conditionally, depending on whether the Blue- tooth LLC is in Sleep mode. The DMC bit must be clear for this mechanism to operate. The HCCM bit is automatically cleared when the device enters Active mode. – High-frequency oscillator is disabled in Power Save or Idle mode only if the DMC bit is set. – High-frequency oscillator is also disabled if the Bluetooth LLC is idle. HCCH The Hardware Clock Control for High-Fre- quency (PLL) bit may be used in Power Save and Idle modes to disable the PLL condition- ally, depending on whether the Bluetooth LLC is in Sleep mode. The DHC bit and the CRC- TRL.PLLPWD bit must be clear for this mech- anism to operate. The HCCH bit is automatically cleared when the device enters Active mode. – PLL is disabled in Power Save or Idle mode only if the DMC bit or the CRC- TRL.PLLPWD bit is set. 1 – PLL is also disabled if the Bluetooth LLC is idle. Obsolete

12.6.2 Power Management Status Register (PMMSR)

the register is shown below. not switch to Power Save, Idle, or Halt mode. 1 – Low-frequency oscillator is available. – High-frequency oscillator is available. – PLL is enabled but unstable.

12.7 SWITCHING BETWEEN POWER MODES

Power Management Control/Status Register (PMMCR). tive mode is usually triggered by a hardware interrupt. Figure 11. Power Mode State Diagram

12.7.1 Active Mode to Power Save Mode

when the transition to the Power Save mode is completed. even before the WAIT instruction is executed.

www.national.com 62 CP3BT23

12.7.2 Entering Idle Mode

Entry into Idle mode is performed by writing a 1 to the PM- MCR.IDLE bit and then executing a WAIT instruction. The PMMCR.WBPSM bit must be set before the WAIT instruc- tion is executed. Idle mode can be entered only from the Ac- tive or Power Save mode.

12.7.3 Disabling the High-Frequency Clock

When the low-frequency oscillator is used to generate the Slow Clock, power consumption can be reduced further in the Power Save or Idle mode by disabling the high-frequen- cy oscillator. This is accomplished by writing a 1 to the PM- MCR.DHC bit before executing the WAIT instruction that puts the device in the Power Save or Idle mode. The high- frequency clock is turned off only after the device enters the Power Save or Idle mode. The CPU operates on the low-frequency clock in Power Save mode. It can turn off the high-frequency clock at any time by writing a 1 to the PMMCR.DHC bit. The high-fre- quency oscillator is always enabled in Active mode and al- ways disabled in Halt mode, without regard to the PMMCR.DHC bit setting. Immediately after power-up and entry into Active mode, software must wait for the low-frequency clock to become stable before it can put the device in Power Save mode. It should monitor the PMMSR.OLC bit for this purpose. Once this bit is set, Slow Clock is stable and Power Save mode can be entered.

12.7.4 Entering Halt Mode

Entry into Halt mode is accomplished by writing a 1 to the PMMCR.HALT bit and then executing a WAIT instruction. The PMMCR.WBPSM bit must be set before the WAIT in- struction is executed. Halt mode can be entered only from Active or Power Save mode.

12.7.5 Software-Controlled Transition to Active Mode

A transition from Power Save mode to Active mode can be accomplished by either a software command or a hardware wake-up event. The software method is to write a 0 to the PMMCR.PSM bit. The value of the register bit changes only after the transition to the Active mode is completed. If the high-frequency oscillator is disabled for Power Save operation, the oscillator must be enabled and allowed to sta- bilize before the transition to Active mode. To enable the high-frequency oscillator, software writes a 0 to the PM- MCR.DMC bit. Before writing a 0 to the PMMCR.PSM bit, software must first monitor the PMMSR.OMC bit to deter- mine when the oscillator has stabilized.

12.7.6 Wake-Up Transition to Active Mode

A hardware wake-up event switches the device directly from Power Save, Idle, or Halt mode to Active mode. Hardware wake-up events are: ! Non-Maskable Interrupt (NMI) ! Valid wake-up event on a Multi-Input Wake-Up channel When a wake-up event occurs, the on-chip hardware per- forms the following steps: 1. Clears the PMMCR.DMC bit, which enables the high- frequency clock (if it was disabled). 2. Waits for the PMMSR.OMC bit to become set, which in- dicates that the high-frequency clock is operating and is stable. 3. Clears the PMMCR.DHC bit, which enables the PLL. 4. Waits for the PMMSR.OHC bit to become set. 5. Switches the device into Active mode.

12.7.7 Power Mode Switching Protection

The Power Management Module has several mechanisms to protect the device from malfunctions caused by missing or unstable clock signals. The PMMSR.OHC, PMMSR.OMC, and PMMSR.OLC bits indicate the current status of the PLL, high-frequency oscil- lator, and low-frequency oscillator, respectively. Software can check the appropriate bit before switching to a power mode that requires the clock. A set status bit indicates an operating, stable clock. A clear status bit indicates a clock that is disabled, not available, or not yet stable. (Except in the case of the PLL, which has a set status bit when dis- abled.) During a power mode transition, if there is a request to switch to a mode with a clear status bit, the switch is delayed until that bit is set by the hardware. When the system is built without an external crystal network for the low-frequency clock, Main Clock is divided by a pres- caler factor to produce the low-frequency clock. In this situ- ation, Main Clock is disabled only in the Halt mode, and cannot be disabled for the Power Save or Idle mode. Without an external crystal network for the low-frequency clock, the device comes out of Halt or Idle mode and enters Active mode with Main Clock driving Slow Clock. Note: For correct operation in the absence of a low-fre- quency crystal, the X2CKI pin must be tied low (not left float- ing) so that the hardware can detect the absence of the crystal. Obsolete

13.0 Multi-Input Wake-Up

input channels and 8 interrupt request outputs. interrupt handler to respond to MIWU events. dler is essential for any wake-up operation. reading the WK0PND or WK1PND register. the pending bit are not synchronous to the System Clock. Figure 12. Multi-Input Wake-Up Module Block Diagram

www.national.com 64 CP3BT23

13.1 MULTI-INPUT WAKE-UP REGISTERS

Table 28 lists the MIWU registers.Table 27 MIWU Sources MIWU Channel Source WUI0 TWM T0OUT WUI1 ACCESS.bus WUI2 CAN0RX WUI3 MWCS WUI4 UART0 CTS WUI5 UART0 RXD WUI6 Bluetooth LLC WUI7 AAI SFS WUI8 Reserved WUI9 PJ7 WUI10 PG6 WUI11 PH0 WUI12 PH1 WUI13 PH2 WUI14 PH3 WUI15 PH4 WUI16 PH5 WUI17 PH6 WUI18 PJ0 WUI19 PJ1 WUI20 PJ2 WUI21 PJ3 WUI22 PJ4 WUI23 PJ5 WUI24 PJ6 WUI25 Reserved WUI26 UART1 RXD WUI27 UART2 RXD WUI28 UART3 RXD WUI29 Reserved WUI30 ADC Done WUI31 CAN1RX Table 28 Multi-Input Wake-Up Registers Name Address Description WK0EDG FF FC80h Wake-Up Edge Detection Register Module 0 WK1EDG FF FCA0h Wake-Up Edge Detection Register Module 1 WK0ENA FF FC82h Wake-Up Enable Register Module 0 WK1ENA FF FCA2h Wake-Up Enable Register Module 1 WK0ICTL1 FF FC84h Wake-Up Interrupt Control Register 1 Module 0 WK1ICTL1 FF FCA4h Wake-Up Interrupt Control Register 1 Module 1 WK0ICTL2 FF FC86h Wake-Up Interrupt Control Register 2 Module 0 WK1ICTL2 FF FCA6h Wake-Up Interrupt Control Register 2 Module 1 WK0PND FF FC88h Wake-Up Pending Register Module 0 WK1PND FF FCA8h Wake-Up Pending Register Module 1 WK0PCL FF FC8Ah Wake-Up Pending Clear Register Module 0 WK1PCL FF FCAAh Wake-Up Pending Clear Register Module 1 WK0IENA FF FC8Ch Wake-Up Interrupt Enable Register Module 0 WK1IENA FF FCACh Wake-Up Interrupt Enable Register Module 1 Obsolete

65 www.national.com CP3BT23

13.1.1 Wake-Up Edge Detection Register (WK0EDG)

The WK0EDG register is a word-wide read/write register that controls the edge sensitivity of the MIWU channels. The WK0EDG register is cleared upon reset, which configures all channels to be triggered on rising edges. The register for- mat is shown below. WKED The Wake-Up Edge Detection bits control the edge sensitivity for MIWU channels. The WKED15:0 bits correspond to the WUI15:0 channels, respectively. – Triggered on rising edge (low-to-high transition). 1 – Triggered on falling edge (high-to-low transition).

13.1.2 Wake-Up 1 Edge Detection Register (WK1EDG)

The WK1EDG register is a word-wide read/write register that controls the edge sensitivity of the MIWU channels. The WK1EDG register is cleared upon reset, which configures all channels to be triggered on rising edges. The register for- mat is shown below. WKED The Wake-Up Edge Detection bits control the edge sensitivity for MIWU channels. The WKED15:0 bits correspond to the WUI31:16 channels, respectively. – Triggered on rising edge (low-to-high transition). 1 – Triggered on falling edge (high-to-low transition).

13.1.3 Wake-Up Enable Register (WK0ENA)

The WK0ENA register is a word-wide read/write register that individually enables or disables wake-up events from the MIWU channels. The WK0ENA register is cleared upon reset, which disables all wake-up/interrupt channels. The register format is shown below. WKEN The Wake-Up Enable bits enable and disable the MIWU channels. The WKEN15:0 bits cor- respond to the WUI15:0 channels, respective- ly. – MIWU channel wake-up events disabled. 1 – MIWU channel wake-up events enabled.

13.1.4 Wake-Up 1 Enable Register (WK1ENA)

The WK1ENA register is a word-wide read/write register that individually enables or disables wake-up events from the MIWU channels. The WK1ENA register is cleared upon reset, which disables all wake-up/interrupt channels. The register format is shown below. WKEN The Wake-Up Enable bits enable and disable the MIWU channels. The WKEN15:0 bits cor- respond to the WUI31:16 channels, respec- tively. – MIWU channel wake-up events disabled. 1 – MIWU channel wake-up events enabled.

13.1.5 Wake-Up Interrupt Enable Register (WK0IENA)

The WK0IENA register is a word-wide read/write register that enables and disables interrupts from the MIWU chan- nels. The register format is shown below. WKIEN The Wake-Up Interrupt Enable bits control whether MIWU channels generate interrupts. The WKIEN15:0 bits correspond to the WUI15:0 channels, respectively. – Interrupt disabled. 1 – Interrupt enabled.

13.1.6 Wake-Up 1 Interrupt Enable Register

(WK1IENA) The WK1IENA register is a word-wide read/write register that enables and disables interrupts from the MIWU chan- nels. The register format is shown below. WK1IEN The Wake-Up Interrupt Enable bits control whether MIWU channels generate interrupts. The WKIEN15:0 bits correspond to the WUI31:16 channels, respectively. – Interrupt disabled. 1 – Interrupt enabled. 15 0 WKED 15 0 WKED 15 0 WKEN 15 0 WKEN 15 0 WKIEN 15 0 WKIEN Obsolete

www.national.com 66 CP3BT23

13.1.7 Wake-Up Interrupt Control Register 1

(WK0ICTL1) The WK0ICTL1 register is a word-wide read/write register that selects the interrupt request signal for the associated MIWU channels WUI7:0. At reset, the WK0ICTL1 register is cleared, which selects MIWU Interrupt Request 0 for all eight channels. The register format is shown below. WKINTR The Wake-Up Interrupt Request Select fields select which of the four MIWU interrupt re- quests are activated for the corresponding channel. 00 – Selects MIWU interrupt request 0. 01 – Selects MIWU interrupt request 1. 10 – Selects MIWU interrupt request 2. 11 – Selects MIWU interrupt request 3.

13.1.8 Wake-Up 1 Interrupt Control Register 1

(WK1ICTL1) The WK1ICTL1 register is a word-wide read/write register that selects the interrupt request signal for the associated MIWU channels WUI23:16. At reset, the WK1ICTL1 register is cleared, which selects MIWU Interrupt Request 4 for all eight channels. The register format is shown below. WKINTR The Wake-Up Interrupt Request Select fields select which of the four MIWU interrupt re- quests are activated for the corresponding channel. 00 – Selects MIWU interrupt request 4. 01 – Selects MIWU interrupt request 5. 10 – Selects MIWU interrupt request 6. 11 – Selects MIWU interrupt request 7.

13.1.9 Wake-Up Interrupt Control Register 2

(WK0ICTL2) The WK0ICTL2 register is a word-wide read/write register that selects the interrupt request signal for the associated MIWU channels WUI15:8. At reset, the WK2ICTL2 register is cleared, which selects MIWU Interrupt Request 0 for all eight channels. The register format is shown below. WKINTR The Wake-Up Interrupt Request Select fields select which of the four MIWU interrupt re- quests are activated for the corresponding channel. 00 – Selects MIWU interrupt request 0. 01 – Selects MIWU interrupt request 1. 10 – Selects MIWU interrupt request 2. 11 – Selects MIWU interrupt request 3.

13.1.10 Wake-Up 1 Interrupt Control Register 2

(WK1ICTL2) The WK1ICTL2 register is a word-wide read/write register that selects the interrupt request signal for the associated MIWU channels WUI31:24. At reset, the WK1ICTL2 register is cleared, which selects MIWU Interrupt Request 4 for all eight channels. The register format is shown below. WKINTR The Wake-Up Interrupt Request Select fields select which of the four MIWU interrupt re- quests are activated for the corresponding channel. 00 – Selects MIWU interrupt request 4. 01 – Selects MIWU interrupt request 5. 10 – Selects MIWU interrupt request 6. 11 – Selects MIWU interrupt request 7. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 WKIN TR7 WKIN TR6 WKIN TR5 WKIN TR4 WKIN TR3 WKIN TR2 WKIN TR1 WKIN TR0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 WKIN TR23 WKIN TR22 WKIN TR21 WKIN TR20 WKIN TR19 WKIN TR18 WKIN TR17 WKIN TR16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 WKIN TR15 WKIN TR14 WKIN TR13 WKIN TR12 WKIN TR11 WKIN TR10 WKIN TR9 WKIN TR8 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 WKIN TR31 WKIN TR30 WKIN TR29 WKIN TR28 WKIN TR27 WKIN TR26 WKIN TR25 WKIN TR24 Obsolete

67 www.national.com CP3BT23

13.1.11 Wake-Up Pending Register (WK0PND)

The WK0PND register is a word-wide read/write register in which the Multi-Input Wake-Up module latches any detect- ed trigger conditions. The CPU can only write a 1 to any bit position in this register. If the CPU attempts to write a 0, it has no effect on that bit. To clear a bit in this register, the CPU must use the WK0PCL register. This implementation prevents a potential hardware-software conflict during a read-modify-write operation on the WK0PND register. This register is cleared upon reset. The register format is shown below. WKPD The Wake-Up Pending bits indicate which MIWU channels have been triggered. The WKPD15:0 bits correspond to the WUI15:0 channels. Writing 1 to a bit sets it. – Trigger condition did not occur. 1 – Trigger condition occurred.

13.1.12 Wake-Up 1 Pending Register (WK1PND)

The WK1PND register is a word-wide read/write register in which the Multi-Input Wake-Up module latches any detect- ed trigger conditions. The CPU can only write a 1 to any bit position in this register. If the CPU attempts to write a 0, it has no effect on that bit. To clear a bit in this register, the CPU must use the WK1PCL register. This implementation prevents a potential hardware-software conflict during a read-modify-write operation on the WK1PND register. This register is cleared upon reset. The register format is shown below. WKPD The Wake-Up Pending bits indicate which MIWU channels have been triggered. The WKPD15:0 bits correspond to the WUI31:15 channels. Writing 1 to a bit sets it. – Trigger condition did not occur. 1 – Trigger condition occurred.

13.1.13 Wake-Up Pending Clear Register (WK0PCL)

The WK0PCL register is a word-wide write-only register that lets the CPU clear bits in the WKPND register. Writing a 1 to a bit position in the WKPCL register clears the corre- sponding bit in the WKPND register. Writing a 0 has no ef- fect. Do not modify this register with instructions that access the register as a read-modify-write operand, such as the bit manipulation instructions. Reading this register location returns undefined data. Therefore, do not use a read-modify-write sequence (such as the SBIT instruction) to set individual bits. Do not attempt to read the register, then perform a logical OR on the regis- ter value. Instead, write the mask directly to the register ad- dress. The register format is shown below. WKCL Writing 1 to a bit clears it. – Writing 0 has no effect. 1 – Writing 1 clears the corresponding bit in the WKPD register.

13.1.14 Wake-Up 1 Pending Clear Register (WK1PCL)

The WK1PCL register is a word-wide write-only register that lets the CPU clear bits in the WK1PND register. Writing a 1 to a bit position in the WK1PCL register clears the corre- sponding bit in the WK1PND register. Writing a 0 has no ef- fect. Do not modify this register with instructions that access the register as a read-modify-write operand, such as the bit manipulation instructions. Reading this register location returns undefined data. Therefore, do not use a read-modify-write sequence (such as the SBIT instruction) to set individual bits. Do not attempt to read the register, then perform a logical OR on the regis- ter value. Instead, write the mask directly to the register ad- dress. The register format is shown below. WKCL Writing 1 to a bit clears it. – Writing 0 has no effect. 1 – Writing 1 clears the corresponding bit in the WK1PD register. 15 0 WKPD 15 0 WKPD 15 0 WKCL 15 0 WKCL Obsolete

www.national.com 68 CP3BT23

13.2 PROGRAMMING PROCEDURES

To set up and use the Multi-Input Wake-Up function, use the following procedure. Performing the steps in the order shown will prevent false triggering of a wake-up condition. This same procedure should be used following a reset be- cause the wake-up inputs are left floating, resulting in un- known data on the input pins. 1. Clear the WK0ENA and WK1ENA registers to disable wake-up events from the MIWU channels. Clear the WK0IENA and WK1IENA registers to disable interrupt requests from the MIWU channels. 2. If the MIWU channel comes from a GPIO pin, select the appropriate alternate function. 3. Write the WK0EDG and WK1EDG registers to select the desired type of edge sensitivity (clear for rising edge, set for falling edge). 4. Set all bits in the WK0PCL and WK0PCL registers to clear any pending bits in the WK0PND and WK1PND registers. 5. Set up the WK0ICTL1, WK1ICTL1, WK0ICTL2, and WK1ICTL2 registers to define the interrupt request sig- nal used for each channel. 6. Set the bits in the WK0ENA and WK1ENA registers corresponding to the wake-up channels to be activated. To change the edge sensitivity of a wake-up channel, use the following procedure. Performing the steps in the order shown will prevent false triggering of a wake-up/interrupt condition. 1. Clear the WK0ENA or WK1ENA bit associated with the input to be reprogrammed. 2. Write the new value to the corresponding bit position in the WK0EDG or WK1EDG register to reprogram the edge sensitivity of the input. 3. Set the corresponding bit in the WK0PCL or WK1PCL register to clear the pending bit in the WK0PND or WK1PND register. 4. Set the same WK0ENA or WK1ENA bit to re-enable the wake-up function. Obsolete

14.0 Input/Output Ports

ganized into 8-bit ports (not all bits are used in some ports). I/O pins are shown in Table 86. environments, not by programming the port registers. pull output, weak pull-up input, or high-impedance input. figured to operate in different modes. buffer is a TRI-STATE buffer with weak pull-up capability. to an undefined state when it operates as an input. general-purpose I/O are only enabled when they are read. put and output buffers are described in Section 29.0. Figure 13. I/O Port Pin Logic

14.1 PORT REGISTERS

www.national.com 70 CP3BT23 In the descriptions of the ports and port registers, the lower- case letter “x” represents the port designation, either B, C, E, F , G, H, or J. For example, “PxDIR register” means any one of the port direction registers: PBDIR, PCDIR, PEDIR, PFDIR, PGDIR, PHDIR, or PJDIR. Table 29 Port Registers Name Address Description PBALT FF FB00h Port B Alternate Function Register PBDIR FF FB02h Port B Direction Register PBDIN FF FB04h Port B Data Input Register PBDOUT FF FB06h Port B Data Output Register PBWPU FF FB08h Port B Weak Pull-Up Register PBHDRV FF FB0Ah Port B High Drive Strength Register PBALTS FF FB0Ch Port B Alternate Function Select Register PCALT FF FB10h Port C Alternate Function Register PCDIR FF FB12h Port C Direction Register PCDIN FF FB14h Port C Data Input Register PCDOUT FF FB16h Port C Data Output Register PCWPU FF FB18h Port C Weak Pull-Up Register PCHDRV FF FB1Ah Port C High Drive Strength Register PCALTS FF FB1Ch Port C Alternate Function Select Register PEALT FF FCC0h Port E Alternate Function Register PEDIR FF FCC2h Port E Direction Register PEDIN FF FCC4h Port E Data Input Register PEDOUT FF FCC6h Port E Data Output Register PEWPU FF FCC8h Port E Weak Pull-Up Register PEHDRV FF FCCAh Port E High Drive Strength Register PEALTS FF FCCCh Port E Alternate Function Select Register PFALT FF FCE0h Port F Alternate Function Register PFDIR FF FCE2h Port F Direction Register PFDIN FF FCE4h Port F Data Input Register PFDOUT FF FCE6h Port F Data Output Register PFWPU FF FCE8h Port F Weak Pull-Up Register PFHDRV FF FCEAh Port F High Drive Strength Register PFALTS FF FCECh Port F Alternate Function Select Register PGALT FF F300h Port G Alternate Function Register PGDIR FF F302h Port G Direction Register PGDIN FF F304h Port G Data Input Register PGDOUT FF F306h Port G Data Output Register PGWPU FF F308h Port G Weak Pull-Up Register PGHDRV FF F30Ah Port G High Drive Strength Register PGALTS FF F30Ch Port G Alternate Function Select Register PHALT FF F320h Port H Alternate Function Register PHDIR FF F322h Port H Direction Register PHDIN FF F324h Port H Data Input Register PHDOUT FF F326h Port H Data Output Register PHWPU FF F328h Port H Weak Pull-Up Register PHHDRV FF F32Ah Port H High Drive Strength Register PHALTS FF F32Ch Port H Alternate Function Select Register PJALT FF F340h Port J Alternate Function Register PJDIR FF F342h Port J Direction Register PJDIN FF F344h Port J Data Input Register PJDOUT FF F346h Port J Data Output Register PJWPU FF F348h Port J Weak Pull-Up Register PJHDRV FF F34Ah Port J High Drive Strength Register PJALTS FF F34Ch Port J Alternate Function Select Register Table 29 Port Registers Name Address Description Obsolete

71 www.national.com CP3BT23 All of the port registers are byte-wide read/write registers, except for the port data input registers, which are read-only registers. Each register bit controls the function of the cor- responding port pin. For example, PGDIR.2 (bit 2 of the PGDIR register) controls the direction of port pin PG2.

14.1.1 Port Alternate Function Register (PxALT)

The PxALT registers control whether the port pins are used for general-purpose I/O or for their alternate function. Each port pin can be controlled independently. A clear bit in the alternate function register causes the cor- responding pin to be used for general-purpose I/O. In this configuration, the output buffer is controlled by the direction register (PxDIR) and the data output register (PxDOUT). The input buffer is visible to software as the data input reg- ister (PxDIN). A set bit in the alternate function register (PxALT) causes the corresponding pin to be used for its peripheral I/O func- tion. When the alternate function is selected, the output buffer data and TRI-ST ATE configuration are controlled by signals from the on-chip peripheral device. A reset operation clears the port alternate function regis- ters, which initializes the pins as general-purpose I/O ports. This register must be enabled before the corresponding al- ternate function is enabled. PxALT The PxALT bits control whether the corre- sponding port pins are general-purpose I/O ports or are used for their alternate function by an on-chip peripheral. – General-purpose I/O selected. 1 – Alternate function selected.

14.1.2 Port Direction Register (PxDIR)

The port direction register (PxDIR) determines whether each port pin is used for input or for output. A clear bit in this register causes the corresponding pin to operate as an in- put, which puts the output buffer in the high-impedance state. A set bit causes the pin to operate as an output, which enables the output buffer. A reset operation clears the port direction registers, which initializes the pins as inputs. PxDIR The PxDIR bits select the direction of the cor- responding port pin. – Input. 1 – Output.

14.1.3 Port Data Input Register (PxDIN)

The data input register (PxDIN) is a read-only register that returns the current state on each port pin. The CPU can read this register at any time even when the pin is config- ured as an output. PxDIN The PxDIN bits indicate the state on the cor- responding port pin. 0 – Pin is low. 1 – Pin is high.

14.1.4 Port Data Output Register (PxDOUT)

The data output register (PxDOUT) holds the data to be driven on output port pins. In this configuration, writing to the register changes the output value. Reading the register returns the last value written to the register. A reset operation leaves the register contents unchanged. At power-up, the PxDOUT registers contain unknown val- ues. PxDOUT The PxDOUT bits hold the data to be driven on pins configured as outputs in general-pur- pose I/O mode. – Drive the pin low. 1 – Drive the pin high.

14.1.5 Port Weak Pull-Up Register (PxWPU)

The weak pull-up register (PxWPU) determines whether the port pins have a weak pull-up on the output buffer. The pull- up device, if enabled by the register bit, operates in the gen- eral-purpose I/O mode whenever the port output buffer is disabled. In the alternate function mode, the pull-ups are al- ways disabled. A reset operation clears the port weak pull-up registers, which disables all pull-ups. PxWPU The PxWPU bits control whether the weak pull-up is enabled. – Weak pull-up disabled. 1 – Weak pull-up enabled. 7 0 PxALT 7 0 PxDIR 7 0 PxDIN 7 0 PxDOUT 7 0 PxWPU Obsolete

www.national.com 72 CP3BT23

14.1.6 Port High Drive Strength Register (PxHDRV)

The PxHDRV register is a byte-wide, read/write register that controls the slew rate of the corresponding pins. The high drive strength function is enabled when the corresponding bits of the PxHDRV register are set. In both GPIO and alter- nate function modes, the drive strength function is enabled by the PxHDRV registers. At reset, the PxHDRV registers are cleared, making the ports low speed. PxHDRV The PxHDRV bits control whether output pins are driven with slow or fast slew rate. – Slow slew rate. 1 – Fast slew rate.

14.1.7 Port Alternate Function Select Register

(PxALTS) The PxALTS register selects which of two alternate func- tions are selected for the port pin. These bits are ignored unless the corresponding PxALT bits are set. Each port pin can be controlled independently. PxALTS The PxALTS bits select among two alternate functions. Table 30 shows the mapping of the PxALTS bits to the alternate functions. Un- used PxALTS bits must be clear. 7 0 PxHDRV 7 0 PxALTS Table 30 Alternate Function Select Port Pin PxALTS = 0 PxALTS = 1 PE0 UART0 RXD0 Reserved PE1 UART0 TXD0 Reserved PE2 UART0 RTS Reserved PE3 UART0 CTS Reserved PE4 UART0 CKX TB PE5 SRFS NMI PE6 CAN1RX Reserved PE7 CAN1TX Reserved PF0 MSK TIO1 PF1 MDIDO TIO2 PF2 MDODI TIO3 PF3 MWCS TIO4 PF4 SCK TIO5 PF5 SFS TIO6 PF6 STD TIO7 PF7 SRD TIO8 PG0 RFSYNC Reserved PG1 RFCE Reserved PG2 BTSEQ1 SRCLK PG3 SCLK Reserved PG4 SDAT Reserved PG5 SLE Reserved PG6 WUI10 BTSEQ2 PG7 TA BTSEQ3 PH0 UART1 RXD1 WUI11 PH1 UART1 TXD1 WUI12 PH2 UART2 RXD2 WUI13 PH3 UART2 TXD2 WUI14 PH4 UART3 RXD3 WUI15 PH5 UART3 TXD3 WUI16 PH6 CAN0RX WUI17 PH7 CAN0TX Reserved PJ0 WUI18 Reserved PJ1 WUI19 Reserved PJ2 WUI20 Reserved PJ3 WUI21 Reserved PJ4 WUI22 Reserved PJ5 WUI23 Reserved PJ6 WUI24 Reserved PJ7 ASYNC WUI9 Table 30 Alternate Function Select Port Pin PxALTS = 0 PxALTS = 1 Obsolete

73 www.national.com CP3BT23

14.2 OPEN-DRAIN OPERATION

A port pin can be configured to operate as an inverting open-drain output buffer. T o do this, the CPU must clear the bit in the data output register (PxDOUT) and then use the port direction register (PxDIR) to set the value of the port pin. With the direction register bit set (direction = out), the value zero is forced on the pin. With the direction register bit clear (direction = in), the pin is placed in the TRI-STATE mode. If desired, the internal weak pull-up can be enabled to pull the signal high when the output buffer is in TRI- STA TE mode. Obsolete

15.0 Bluetooth Controller

15.1 RF INTERFACE

chips though the RF interface. Figure 14. LMX5251 Interface Figure 15. LMX5252 Interface which may be used with other RF transceiver chips.

15.1.1 RF Interface Signals

CP3BT23 for use as the Main Clock. face pin. This signal is driven to a logic high level after reset. received access code is achieved.

PG0 pin to give control over this signal to the RF interface. PG1 pin to give control over this signal to the RF interface. the Hardware Clock Control mechanism. The SCLK signal is the serial interface shift clock output. give control over this signal to the RF interface. transmit path between the radio chip and the CP3BT23. pose I/O pin PG4. At reset, this pin is in TRI-STATE mode. to give control over this signal to the RF interface. after the SLE signal goes high. over this signal to the RF interface.

15.2 SERIAL INTERFACE

over the data signal from the CP3BT23 to the radio chip. Figure 16 shows the serial interface protocol format. Figure 16. Serial Interface Protocol Format

15.3 LMX5251 POWER-UP SEQUENCE

1. Apply VDD to the LMX5251.
2. Apply IOVCC and VCC to the CP3BT23.
3. Drive the RESET# pin of the LMX5251 high a minimum

powered up. This resets the LMX5251 and CP3BT23.

1. After internal Power-On Reset (POR) of the CP3BT23,
2. When the RFDATA pin is driven high, the LMX5251 en-
3. The Bluetooth baseband processor on the CP3BT23

the logic levels required during the power-up phase.

1. In “normal” mode, the oscillator of the LMX5251 is con-

Figure 23. LMX5251 Power-Up Sequence

15.4 LMX5252 POWER-UP SEQUENCE

enters Idle mode and drives BRCLK (BBCLK). Figure 24. LMX5252 Power States the CP3BT23 and LMX5252 devices is shown in Figure 25.

Figure 25. LMX5252 Power-Up Sequence

15.5 BLUETOOTH SLEEP MODE

(counter N and counter M) running at the Slow Clock rate. These counters determine the duration of the sleep mode.

1. The current Bluetooth counter contents are read by the
2. Software “estimates” the Bluetooth counter value after
3. The new Bluetooth counter value is written into the
4. The Bluetooth sequencer RAM is updated with the
5. The Bluetooth sequencer RAM and the Bluetooth LLC

the CPU no longer has access to the Bluetooth LLC.

1. Hardware Clock Control (HCC) is enabled, and the
2. The Bluetooth sequencer checks if HCC is enabled. If

the Bluetooth sequencer is stopped.

1. The M-counter starts counting. After M + 1 Slow Clock

cycles, the HCC signal to the PMM is deasserted.

1. The PMM restarts the 12 MHz Main Clock (and the
2. The Bluetooth sequencer waits for the completion of
3. The PMM switches the System Clock to the high-fre-

enabled, an interrupt is issued to the CPU. Figure 26. Bluetooth Sleep Mode Sequence

15.6 BLUETOOTH GLOBAL REGISTERS

15.7 BLUETOOTH SEQUENCER RAM

1 MHz/12 MHz

www.national.com 80 CP3BT23

15.8 BLUETOOTH SHARED DATA RAM

The shared data RAM is a 4.5K memory-mapped section of RAM that contains the link control data, RF programming look-up table, and the link payload. This RAM can be read and written in the same way as the Static RAM space and can also be read by the sequencer in the Bluetooth LLC. Ar- bitration between these devices is performed in hardware. Table 33 shows the memory map of the Bluetooth LLC shared Data RAM. Table 33 Memory Map of Bluetooth Shared RAM Address (offset from 0E 8000h) Description 0000 h–01D9h RF Programming Look-up Table 01DAh –01FFh Unused 0200h–023Fh Link Control 0 0240h–027Fh Link Control 1 0280h–02BFh Link Control 2 02C0h –02FFh Link Control 3 0300h–033Fh Link Control 4 0340h–037Fh Link Control 5 0380h–03BFh Link Control 6 03C0h –03FFh Link Control 7 0400h–11FFh Link Payload 0–6 Obsolete

Figure 27. Analog to Digital Converter Block Diagram

16.1 FUNCTIONAL DESCRIPTION

ic to control triggering of the converter, and a bus interface.

16.1.1 Data Path

and the ADCIN external analog input. word FIFO used to queue conversion results. touchscreens are controlled by the TOUCH_CFG field.

www.national.com 82 CP3BT23 The output of the Input Multiplexer is available externally as the MUXOUT0 and MUXOUT1 signals. In single-ended mode, only MUXOUT0 is used. In differential mode, MUXOUT0 is the positive side and MUXOUT1 is the nega- tive side. The MUXOUT0 and MUXOUT1 outputs and the ADCIN external analog input are provided so that external signal conditioning circuits (such as filters) may be applied to the analog signals before conversion. The MUXOUT0, MUXOUT1, and ADCIN signals are alternate functions of GPIO pins used by the Input Multiplexer, so the number of available analog input channels is reduced when these sig- nals are used.

16.1.2 Operation

The TRIGGER block may be configured to initiate a conver- sion from either of these sources: ! External ASYNC Input—an edge on the ASYNC input triggers a conversion. This input may be configured to be sensitive to rising or falling edges, as controlled by the POL bit in the ADCCNTRL register. ! ADCSTART Register —writing any value to the ADC- START register triggers a conversion. The TRIGGER block incorporates a glitch filter to suppress transient spikes on the ASYNC input. The TRIGGER block will recognize ASYNC pulse widths of 10 ns or greater. Once a trigger event has been recognized, no further trig- gering is recognized until the conversion is completed. When the ASYNC input is selected as the trigger source, it may be configured for automatic or non-automatic mode, as controlled by the AUTO bit in the ADCCNTRL register: ! Automatic Mode —a conversion is triggered by any qualified edge on the ASYNC input (unless a conversion is already in progress). ! Non-Automatic Mode —before a conversion may be triggered from the ASYNC input, software must “prime” the TRIGGER block by writing the ADCSTART register. Once the TRIGGER block is primed, a conversion is trig- gered by any qualified edge on the ASYNC input. After the conversion is completed, no additional trigger events will be recognized until software once again primes the TRIGGER block by writing the ADCSTART register. Once a trigger event is recognized, the DELAY1 block waits for a programmable delay specified in the ADC_DELAY1 field of the ADCSCDL Y register. Then, it asserts the Start signal to the ADC SEQUENCER block. When the Start signal is received, the ADC SEQUENCER block initiates the conversion in the 12-Bit ADC. After the conversion is complete, the result is loaded into the FIFO, and the Done signal is asserted. The ADCRESLT register includes the software-visible end of a 4-word FIFO, which allows up to 4 conversion results to be queued for reading. Reading the ADCRESLT register un- loads the FIFO. If the FIFO overflows, a bit is set in the AD- CRESLT register, and the most recent conversion data is lost. The Done signal is visible to software as the ADC_DONE bit in the ADCRESLT register. The Done signal is also an input to the interrupt controller (IRQ13). The interrupt will be as- serted whenever the FIFO is not empty (but will deassert for one system clock after the ADCRESLT register is read). T o- tal conversion time is around 15 microseconds. The Done signal is also an input to the Multi-Input Wake-Up unit (WUI30). The MIWU input is asserted whenever the FIFO is not empty (but will deassert for one system clock af- ter the ADCRESLT register is read). The wake-up output is provided so that the ADC module can bring the system out of a power-saving mode when a conversion operation is completed. It asserts earlier than the interrupt output. In the pen-down detection mode of the ADC, the wake-up output is ORed with the ADC pen-down detector output, to wake up on a pen-down event.

16.1.3 ADC Clock Generation

The DELAY2 block generates ADC Clock, which is the clock used internally by the ADC module. ADC Clock is derived from either: ! System Clock—a programmable divider is available to generate the 12 MHz clock required by the ADC from the System Clock. ! Auxiliary Clock 2—may be used to perform conversions when the System Clock is slowed down or suspended in low-power modes. The DELAY2 block receives the clock source selected by the CLKSEL bit of the ADCACR register and adds a number of asynchronous incremental delay units specified in the ADC_DELAY2 field of the ADCSCDL Y register. This de- layed clock (ADC Clock) then drives the TRIGGER, 12-BIT ADC, and ADC SEQUENCER blocks. ADC Clock also drives the ADC_DIV clock divider, which generates the clock which drives the DELAY1 block. Because the ADCRESLT FIFO is driven by System Clock (not ADC Clock), a conversion result will not propagate to the output of the FIFO when the System Clock is suspend- ed.

16.1.4 ADC Voltage References

The 12-BIT ADC block has positive and negative voltage reference inputs, VREFP and VREFN. In single-ended mode, only VREFP is used. An analog multiplexer allows selecting an external VREFP pin, the analog supply voltage AVCC, or the analog inputs ADC0 or ADC1 as the positive voltage reference, as controlled by the PREF_CFG field of the ADCGCR register. Another analog multiplexer allows selecting the analog ground AGND or the analog inputs ADC2 or ADC3 as the negative voltage reference, as con- trolled by the NREF_CFG field of the ADCGCR register.

16.1.5 Pen-Down Detector

A pen-down detector is provided on the ADC0 (TSX+) input of the ADC. It consists of a Schmitt-trigger receiver, with a minimum Vil of 0.7V . When pen-down detect mode is en- abled by loading 101b into the TOUCH_CFG field of the AD- CGCR register, the output of this detector is visible to software in the PEN_DOWN bit of the ADCRESLT register, and this output is ORed with the Done signal to become the wake-up input (WUI30) to the Multi-Input Wake-Up unit. Obsolete

16.2 TOUCHSCREEN INTERFACE

Figure 28. Touchscreen Interface other plate. This is done twice, once for each coordinate. pled to the touchscreen signals from the display drivers.

16.2.1 Touchscreen Driver Configuration

Figure 29. Touchscreen Driver Equivalent Circuit on-resistance of these drivers is specified to be 6 ohms. of the pen contact on the X plate. to GND, and leaving the TSX+ and TSX- signals undriven. used to sample node A and 001b used to sample node B. column drivers is averaged out. The plate-to-plate resistance is shown in Figure 29 as RZ. is pulled to GND, to support measuring RZ.

16.2.2 Measuring Pen Force

nored because it has no significant effect. Figure 30. Touchscreen Driver Modes TSY - inputs is the center tap of a resistor-divider network.

16.2.3 Compensation for Driver Resistance

1. The voltages on, for example, TSY+ and TSY - can be

absolute positioning is necessary. Screen Overlay—for example, for cursor positioning. necessary to sample TSY+ and TSY -.

1. The ADC has a positive voltage reference input which

85 www.national.com CP3BT23 3. By extension, the ADC negative voltage reference can be internally connected to the TSY - terminal, to recover the full 4096 values. The Global Configuration Register (ADCGCR) provides the flexibility to implement any of these techniques.

16.3 ADC OPERATION IN POWER-SAVING

To reduce the level of switching noise in the environment of the ADC, it is possible to operate the CP3BT23 in low-power modes, in which the System Clock is slowed or switched off. Under these conditions, Auxiliary Clock 2 can be selected as the clock source for the ADC module, however conver- sion results cannot be read by the system while the System Clock is suspended. The expected operation in power-sav- ing modes is therefore: 1. ADC is configured and a conversion is primed or trig- gered. 2. A power-saving mode is entered. 3. ADC conversion completes and a wake-up signal is as- serted to the MIWU unit. 4. Device wakes up and processes the conversion result. To conserve power, the ADC should be disabled before en- tering a low-power mode if its function is not required.

16.4 FREEZE

The ADC module provides support for an In-System Emula- tor by means of a special FREEZE input. When FREEZE is asserted the module will exhibit the following specific be- havior: ! The automatic clear-on-read function of the result regis- ter (ADCRESLT) is disabled. ! The FIFO is updated as usual, and an interrupt for a completed conversion can be asserted.

16.5 ADC REGISTER SET

Table 34 lists the ADC registers. Table 34 ADC Registers Name Address Description ADCGCR FF F3C0h ADC Global Configuration Register ADCACR FF F3C2h ADC Auxiliary Configuration Register ADCCNTRL FF F3C4h ADC Conversion Control Register ADCSTART FF F3C6h ADC Start Conversion Register ADCSCDLY FF F3C8h ADC Start Conversion Delay Register ADCRESLT FF F3CAh ADC Result Register Obsolete

www.national.com 86 CP3BT23

16.5.1 ADC Global Configuration Register (ADCGCR)

The ADCGCR register controls the basic operation of the in- terface. The CPU bus master has read/write access to the ADCGCR register. After reset this register is set to 0000h. CLKEN The Clock Enable bit controls whether the ADC module is running. When this bit is clear, all ADC clocks are disabled, the ADC analog circuits are in a low-power state, and ADC registers (other than the ADCGCR and AG- CACR registers) are not writeable. Clearing this bit reinitializes the ADC state machine and cancels any pending trigger event. When this bit is set, the ADC clocks are enabled and the ADC analog circuits are powered up. The converter is operational within 0.25 µs of be- ing enabled. 0 – ADC disabled. 1 – ADC enabled. ADCIN The ADCIN bit selects the source of the ADC input. When the bit is clear, the source is the 8-channel Input Multiplexer. When the bit is set, the source is the ADCIN pin. 0 – ADC input is from 8-channel multiplexer. 1 – ADC input is from ADCIN pin. DIFF The Differential Operation Mode bit and the MUX_CFG field configure the analog circuits of the ADC module. When this bit is clear, the ADC module operates in single-ended mode. When this bit is set, the ADC operates in dif- ferential mode. See Table 35 . 0 – Single-ended mode. 1 – Differential mode. MUX_CFG The Multiplexer Configuration field and the DIFF bit configure the analog circuits of the ADC module, as shown in Table 35. For best noise immunity in touchscreen appli- cations, channel 2 should be used for sam- pling the X plate voltage, and channel 1 should be used for sampling the Y plate volt- age. TOUCH_CFG The Touchscreen Configuration field controls the configuration of the low-ohmic drivers for the TSX+, TSX-, TSY+, and TSY - signals, as shown in Table 36. When TOUCH_CFG is 101b, the pen-down detector is enabled. The output of the pen-down detector is visible to software in the PEN_DOWN bit of the AD- SRESLT register, and it is ORed with the Done signal to generate the wake-up signal WUI30 passed to the MIWU unit. 876 5 4 3 2 1 0 TOUCH_CFG MUX_CFG DIFF ADCIN CLKEN 15 14 13 12 11 10 9 MUXOUTEN INTEN Res. NREF_CFG PREF_CFG Table 35 MUX_CFG Operation MUX_CFG Channel Selected, (DIFF = 0) Channels Selected (DIFF = 1) 000 0 0 1 001 1 1 0 010 2 2 3 011 3 3 2 100 4 4 5 101 5 5 4 110 6 6 7 111 7 7 6 Table 36 TOUCH_CFG Modes TOUCH_CFG ADC0/TSX+ ADC1/TSY+ ADC2/TSX- ADC3/TSY- Mode

000 Inactive Inactive Inactive Inactive None

001 Inactive Driven High Inactive Driven Low Sample Y

010 Driven High Inactive Driven Low Inactive Sample X

011 Driven High Inactive Inactive Driven Low Sample Z (1),

100 Inactive Driven High Driven Low Inactive Sample Z (2)

101 Weakly Pulled High Inactive Inactive Driven Low Pen-Down Detect

11X Inactive Inactive Inactive inactive Reserved Obsolete

87 www.national.com CP3BT23 PREF_CFG The Positive Voltage Reference Configuration field specifies the source of the ADC positive voltage reference, according to the following table: NREF_CFG The Negative Voltage Reference Configura- tion field specifies the source of the ADC neg- ative voltage reference, according to the following table: MUXOUTEN The MUXOUT Enable bit controls whether the output of the Input Multiplexer is available ex- ternally. In single-ended mode, the MUXOUT0 pin is active and the MUXOUT1 pin is disabled (TRI-STATE). In differential mode, both MUXOUT0 and MUXOUT1 are active. 0 – MUXOUT0 and MUXOUT1 disabled. 1 – MUXOUT0 and MUXOUT1 enabled. INTEN The Interrupt Enable bit controls whether the ADC interrupt (IRQ13) is enabled. When en- abled, the interrupt request is asserted when valid data is available in the ADCRESLT reg- ister. This bit has no effect on the wake_up signal to the MIWU unit (WUI30). 0 – IRQ13 disabled. 1 – IRQ13 enabled.

16.5.2 ADC Auxiliary Configuration Register

(ADCACR) The ADCACR register is used to control the clock configu- ration and report the status of the ADC module. The CPU bus master has read/write access to the ADCACR register. After reset, this register is clear. CLKSEL The Clock Select bit selects the clock source used by the DELAY2 block to generate the ADC clock. 0 – ADC clock derived from System Clock. 1 – ADC clock derived from Auxiliary Clock 2. CLKDIV The Clock Divisor field specifies the divisor applied to System Clock to generate the 12 MHz clock required by the ADC module. Only the System Clock is affected by this divisor. The divisor is not used when Auxiliary Clock 2 is selected as the clock source. PRM The ADC Primed bit is a read-only bit that in- dicates the ADC has been primed to perform a conversion by writing to the ADCSTART reg- ister. The bit is cleared after the conversion is completed. 0 – ADC has not been primed. 1 – ADC has been primed. TRG The ADC Triggered bit is a read-only bit that indicates the ADC has been triggered. The bit is set during any pre-conversion delay. The bit is cleared after the conversion is completed. 0 – ADC has not been triggered. 1 – ADC has been triggered. CNVT The ADC Conversion bit is a read-only bit that indicates the ADC has been primed to per- form a conversion, a valid internal or external trigger event has occurred, any pre-conver- sion delay has expired, and the ADC conver- sion is in progress. The bit is cleared after the conversion is completed. 0 – ADC is not performing a conversion. 1 – ADC conversion is in progress. PREF_CFG PREF Source

00 Internal (AVCC)

01 VREFP

10 ADC0

11 ADC1

NREF_CFG NREF source

00 Internal (AGND)

01 Reserved

10 ADC2

11 ADC3

CNVT TRG PRM Reserved CLKDIV CLKSEL CLKDIV Clock Divisor 00 1 01 2 10 4

11 Reserved

www.national.com 88 CP3BT23

16.5.3 ADC Conversion Control Register

(ADCCNTRL) The ADCCNTRL register specifies the trigger conditions for an ADC conversion. POL The ASYNC Polarity bit specifies the polarity of edges which trigger ADC conversions. 0 – ASYNC input is sensitive to rising edges. 1 – ASYNC input is sensitive to falling edges. EXT The External Trigger bit selects whether con- versions are triggered by writing the ADC- START register or activity on the ASYNC input. 0 – ADC conversions triggered by writing to the ADCSTART register. 1 – ADC conversions triggered by qualified edges on ASYNC input. AUTO The Automatic bit controls whether automatic mode is enabled, in which any qualified edge on the ASYNC input is recognized as a trigger event. When automatic mode is disabled, the ADC module must be “primed” before a qual- ified edge on the ASYNC input can trigger a conversion. To prime the ADC module, soft- ware must write the ADCSTART register with any value before an edge on the ASYNC input is recognized as a trigger event. After the con- version is completed, the ASYNC input will be ignored until software again writes the ADC- START register. The AUTO bit is ignored when the EXT bit is 0. 0 – Automatic mode disabled. 1 – Automatic mode enabled.

16.5.4 ADC Start Conversion Register (ADCSTART)

The ADCSTART register is a write-only register used by software to initiate an ADC conversion. Writing any value to this register will cause the ADC to initiate a conversion or prime the ADC to initiate a conversion, as controlled by the ADCCNTRL register.

16.5.5 ADC Start Conversion Delay Register

(ADCSCDLY) The ADCSCDL Y register controls critical timing parameters for the operation of the ADC module. ADC_DELAY2 The ADC Delay 2 field specifies the delay be- tween the ADC module clock source (either System Clock after a programmable divider or Auxiliary Clock 2) and the ADC clock. The range of effective values for this field is 0 to 20. Values above 20 produce the same delay as 20, which is about 42 ns. ADC_DELAY1 The ADC Delay 1 field specifies the number of clock periods by which the trigger event will be delayed before initiating a conversion. The timebase for this delay is the ADC clock (12 MHz) divided by the ADC_DIV divisor. The ADC_DELAY1 field has 9 bits, which corre- sponds to a maximum delay of 511 clock peri- ods. ADC_DIV The ADC Clock Divisor field specifies the divi- sor applied to the ADC clock (12 MHz) to gen- erate the clock used to drive the DELAY1 block. A field value of n results in a division ra- tio of n+1. With a module clock of 12 MHz, the maximum delay which can be provided by ADC_DIV and ADC_DELAY settings is: 15 3 2 1 0 Reserved AUTO EXT POL 15 14 13 5 4 0 ADC_DIV ADC_DELAY1 ADC_DELAY2  4× 511× 170 us= Obsolete

89 www.national.com CP3BT23

16.5.6 ADC Result Register (ADCRESLT)

The ADCRESLT register includes the software-visible end of a 4-word FIFO. Conversion results are loaded into the FIFO from the 12-bit ADC and unloaded when software reads the ADCRESLT register. The ADCRESLT register is read-only. With the exception of the PEN_DOWN bit, the fields in this register are cleared when the register is read. ADC_RESULT The ADC Result field holds a 12-bit value for the conversion result. If the ADC_DONE bit is clear, there is no valid result in this field, and the field will have a value of 0. The ADC_RESULT field and the SIGN bit together form the software-visible end of the ADC FIFO. SIGN The Sign bit indicates whether the - input has a voltage greater than the + input (differential mode only). For example if AD- CGCR.MUX_CFG is 000b, ADC0 is the + in- put and ADC1 is the - input. If the voltage on ADC0 is greater than the voltage on ADC1, the SIGN bit will be 0; if the voltage on ADC0 is less than the voltage on ADC1, the SIGN bit will be 1. In single-ended mode, this bit always reads as 0. 0 – In differential mode, + input has a voltage greater than the - input. In single-ended mode, this bit is always 0. 1 – In differential mode, - input has a voltage greater than the + input. PEN_DOWN The Pen-Down bit indicates whether a pen- down condition is being sensed. To enable pen-down detection, the TOUCH_CFG field of the ADCGCR register must be loaded with 101b. The sense of the PEN_DOWN bit is in- verted, so when pen-down detection is en- abled and a pen-down condition is sensed, the PEN_DOWN bit is clear. This bit is not car- ried through the FIFO, so its value represents the current status of the pen-down detector. When pen-down detection is enabled, the un- inverted signal from the pen-down detector is ORed with the Done signal to generate the wake-up signal (WUI30) passed to the MIWU unit. If pen-down detection is not enabled, this bit reads as 0. 0 – Pen-down condition is sensed, or pen- down detection is disabled. 1 – No pen-down condition is sensed. ADC_OFLW The ADC FIFO Overflow bit indicates whether the 4-word FIFO behind the ADCRESLT reg- ister has overflowed. When this occurs, the most recent conversion result is lost. This bit is cleared when the ADCRESLT register is read. 0 – FIFO overflow has not occurred. 1 – FIFO overflow has occurred. ADC_DONE The ADC Done bit indicates when an ADC conversion has completed. When this bit is set, the data in the ADC_RESULT field is val- id. When this bit is clear, there is no valid data in the ADC_RESULT field. The Done bit is cleared when the ADCRESLT register is read, but if there are queued conversion results in the FIFO, the Done bit will become set again after one System Clock period. 0 – No ADC conversion has completed since the ADCRESLT register was last read. 1 – An ADC conversion has completed since the ADCRESLT register was last read. 11 0 ADC_RESULT 15 14 13 12 ADC_DONE ADC_OFLW PEN_DOWN SIGN Obsolete

17.0 Random Number Generator (RNG)

ear feedback shift register (LFSR). kHz, but it does not have a fixed frequency. ister is cleared and the interrupt request is deasserted. ! RNG Enable—enables or disables the RNG oscillators. a new word of random data becomes available. ! Data Valid— indicates whether a new word is available.

17.1 FREEZE

Figure 31. RNG Module Block Diagram

91 www.national.com CP3BT23

17.2 RANDOM NUMBER GENERATOR

Table 34 lists the RNG registers.

17.2.1 RNG Control and Status Register (RNGCST)

The RNGCST register provides control and status bits for the RNG module. This register is cleared at reset. RNGE The Random Number Generator Enable bit enables the operation of the RNG. When this bit is clear, the RNG module is disabled, and both RNG oscillators are suspended. 0 – RNG module disabled. 1 – RNG module enabled. DVALID The Data Valid bit indicates whether valid (random) data is available in the RNGD regis- ter. This bit is cleared when the RNGD regis- ter is read. 0 – RNGD register holds invalid data. 1 – RNGD register holds valid data. IMASK The Interrupt Mask bit controls whether an in- terrupt request (IRQ3) will be asserted when valid (random) data is available in the RNGD register. 0 – RNG interrupt disabled. 1 – RNG interrupt enabled.

17.2.2 RNG Data Register (RNGD)

The RNGD register holds random data generated by the RNG module. After reading the register, it is cleared and the DVALID bit of the RNGCST register is cleared. When a new word of valid (random) data becomes available in the RNGD register, the DVALID bit is set and (if enabled) and interrupt request is asserted.

17.2.3 RNG Divisor Register High (RNGDIVH)

This register holds the two most significant bits of the RNGDIV clock divisor. See the description of the RNGDIVL register.

17.2.4 RNG Divisor Register Low (RNGDIVL)

This register holds the 16 least significant bits the RNGDIV clock divisor. The RNGDIV clock divisor is used to generate the sampling strobe for loading random bits into the shift register. The di- visor is applied to the System Clock source. The maximum frequency after division is 800 Hz. For example, a System Clock frequency of 24 MHz would require an RNGDIV value of 30,000 (7530h) or greater. The default RNGDIV value is 0000 83D6h. Table 37 RNG Registers Name Address Description RNGCST FF F280h RNG Control and Status Register RNGD FF F282h RNG Data Register RNGDIVH FF F284h RNG Divisor Register High RNGDIVL FF F286h RNG Divisor Register Low 1 5 654 2 1 0 Reserved IMSK Reserved DVALID RNGE 15 0 RNGD15:0 15 2 1 0 Reserved RNGDIV17:16 15 0 RNGDIV15:0 Obsolete

www.national.com 92 CP3BT23

18.0 CAN Module

Each of the two CAN modules provides a Full CAN class, CAN (Controller Area Network) serial bus interface for low/ high speed applications. They support reception and trans- mission of extended frames with a 29-bit identifier, standard frames with an 11-bit identifier, applications that require high speed (up to 1 MBit/s), and a low-speed CAN interface with CAN master capability. Data transfer between the CAN bus and the CPU is handled by 15 message buffers, which can be individually configured as receive or transmit buffers. Every message buffer includes a status/control register which provides information about its current status and ca- pabilities to configure the buffer. All message buffers are able to generate an interrupt on the reception of a valid frame or the successful transmission of a frame. In addition, an interrupt can be generated on bus errors. An incoming message is only accepted if the message iden- tifier passes one of two acceptance filtering masks. The fil- tering mask can be configured to receive a single message ID for each buffer or a group of IDs for each receive buffer. One of the buffers uses a separate message filtering proce- dure. This provides the capability to establish a BASIC-CAN path. Remote transmission requests can be processed au- tomatically by automatic reconfiguration to a receiver after transmission or by automated transmit scheduling upon re- ception. A priority decoder allows any buffer to have one of 16 transmit priorities including the highest or lowest abso- lute priority, for a total of 240 different transmit priorities. A decided bit time counter (16-bit wide) is provided to sup- port real time applications. The contents of this counter are captured into the message buffer RAM on reception or transmission. The counter can be synchronized through the CAN network. This synchronization feature allows a reset of the counter after the reception or transmission of a mes- sage in buffer 0. Each CAN module is a fast CPU bus peripheral which al- lows single-cycle byte or word read/write access. The CPU controls the CAN module by programming the registers in the CAN register block. This includes initialization of the CAN baud rate, logic level of the CAN pins, and enable/dis- able of the CAN module. A set of diagnostic features, such as loopback, listen only, and error identification, support de- velopment with the CAN module and provide a sophisticat- ed error management tool. Each CAN module implements the following features: ! CAN specification 2.0B — Standard data and remote frames — Extended data and remote frames — 0 to 8 bytes data length — Programmable bit rate up to 1 Mbit/s ! 15 message buffers, each configurable as receive or transmit buffers — Message buffers are 16-bit wide dual-port RAM — One buffer may be used as a BASIC-CAN path ! Remote Frame support — Automatic transmission after reception of a Remote Transmission Request (RTR) — Auto receive after transmission of a RTR ! Acceptance filtering — Two filtering capabilities: global acceptance mask and individual buffer identifiers — One of the buffers uses an independent acceptance filtering procedure ! Programmable transmit priority ! Interrupt capability — One interrupt vector for all message buffers (receive/ transmit/error) — Each interrupt source can be enabled/disabled ! 16-bit counter with time stamp capability on successful reception or transmission of a message ! Power Save capabilities with programmable Wake-Up over the CAN bus (alternate source for the Multi-Input Wake-Up module) ! Push-pull capability of the input/output pins ! Diagnostic functions — Error identification — Loopback and listen-only features for test and initial- ization purposes

18.1 FUNCTIONAL DESCRIPTION

As shown in Figure 32, each CAN module consists of three blocks: the CAN core, interface management, and a dual- ported RAM containing the message buffers. There are two dedicated device pins for each CAN interface, CANnTX as the transmit output and CANnRX as the receive input. The CAN core implements the basic CAN protocol features such as bit-stuffing, CRC calculation/checking, and error management. It controls the transceiver logic and creates error signals according to the bus rules. In addition, it con- verts the data stream from the CPU (parallel data) to the se- rial CAN bus data. The interface management block is divided into the register block and the interface management processor. The regis- ter block provides the CAN interface with control information from the CPU and provides the CPU with status information from the CAN module. Additionally, it generates the interrupt to the CPU. The interface management processor is a state machine ex- ecuting the CPU’s transmission and reception commands and controlling the data transfer between several message buffers and the RX/TX shift registers. 15 message buffers are memory mapped into RAM to trans- mit and receive data through the CAN bus. Eight 16-bit reg- isters belong to each buffer. One of the registers contains control and status information about the message buffer configuration and the current state of the buffer. The other registers are used for the message identifier, a maximum of up to eight data bytes, and the time stamp information. Dur- ing the receive process, the incoming message will be stored in a hidden receive buffer until the message is valid. Then, the buffer contents will be copied into the first mes- sage buffer which accepts the ID of the received message. Obsolete

Figure 32. CAN Block Diagram

18.2 BASIC CAN CONCEPTS

cepts of the Controller Area Network (CAN). remote frame has been completed. process existing data to perform a new functionality. mation, it can send an overload frame.

and switches to receive mode, as shown in Figure 33. Figure 33. CAN Message Arbitration has canceled the transmit request. message which has the highest internal transmit priority.

18.2.1 CAN Frame Types

i.e., the bus is idle, the bus is kept at the “recessive” level. field, control field, data field (if present), and CRC field. stream for consecutive ones and zeros.

18.2.2 CAN Frame Fields

which starts transmission first. inant” in a data frame and “recessive” in a remote frame.

The DLC field indicates the number of bytes in the data field. It consists of four bits. The data field can be of length zero. cessive” bit is transmitted as the CRC delimiter. bit called the acknowledge delimiter. consists of seven “recessive” bits.

18.2.3 CAN Frame Formats

Figure 34. The structure of an extended data frame is Figure 34. Standard Data Frame Figure 35. Extended Data Frame

Figure 40. Interframe Space

18.2.4 Error Types

slot is not interpreted as a bit error. state change in a message field encoded with bit stuffing. Frame does not constitute a frame error. culation of a received CRC polynomial is non-zero. nant” bit during the ACK frame). Figure 41. Bus States Suspend Transmission is only for error passive nodes.

99 www.national.com CP3BT23 Error Active An error active unit can participate in bus communication and may send an active (“dominant”) error flag. Error Warning The Error Warning state is a sub-state of Error Active to in- dicate a heavily disturbed bus. The CAN module behaves as in Error Active mode. The device is reset into the Error Active mode if the value of both counters is less than 96. Error Passive An error passive unit can participate in bus communication. However, if the unit detects an error it is not allowed to send an active error flag. The unit sends only a passive (“reces- sive”) error flag. A device is error passive when the transmit error counter or the receive error counter is greater than 127. A device becoming error passive will send an active er- ror flag. An error passive device becomes error active again when both transmit and receive error counter are less than 128. Bus Off A unit that is bus off has the output drivers disabled, i.e., it does not participate in any bus activity. A device is bus off when the transmit error counter is greater than 255. A bus off device will become error active again after monitoring 128 × 11 “recessive” bits (including bus idle) on the bus. When the device goes from “bus off“ to “error active“, both error counters will have a value of 0.

18.2.5 Error Counters

There are multiple mechanisms in the CAN protocol to de- tect errors and inhibit erroneous modules from disabling all bus activities. Each CAN module includes two error counters to perform error management. The receive error counter (REC) and the transmit error counter (TEC) are 8- bits wide, located in the 16-bit wide CANEC register. The counters are modified by the CAN module according to the rules listed in T able 38. This table provides an overview of the CAN error conditions and the behavior of the CAN mod- ule; for a detailed description of the error management and fault confinement rules, refer to the CAN Specification 2.0B. If the MSB (bit 7) of the REC is set, the node is error passive and the REC will not increment any further. The Error counters can be read by application software as described under CAN Error Counter Register (CANECn) on page 122. Special error handling for the TEC counter is performed in the following situations: ! A stuff error occurs during arbitration, when a transmitted “recessive” stuff bit is received as a “dominant” bit. This does not lead to an increment of the TEC. ! An ACK-error occurs in an error passive device and no “dominant” bits are detected while sending the passive error flag. This does not lead to an increment of the TEC. ! If only one device is on the bus and this device transmits a message, it will get no acknowledgment. This will be detected as an error and the message will be repeated. When the device goes “error passive” and detects an ac- knowledge error, the TEC counter is not incremented. Therefore the device will not go from ”error passive” to the “bus off” state due to such a condition. Table 38 Error Counter Handling Condition Action Receive Error Counter Conditions A receiver detects a bit error during sending an active error flag. Increment by 8 A receiver detects a “dominant“ bit as the first bit after sending an error flagIncrement by 8 After detecting the 14th consecutive “dominant“ bit following an active error flag or overload flag, or after detecting the 8th consecutive “dominant“ bit following a passive error flag. After each sequence of additional 8 consecutive “dominant” bits. Increment by 8 Any other error condition (stuff, frame, CRC, ACK) Increment by 1 A valid reception or transmission Decrement by 1 unless counter is already 0 Transmit Error Counter Conditions A transmitter detects a bit error while sending an active error flag Increment by 8 After detecting the 14th consecutive “dominant“ bit following an active error flag or overload flag or after detecting the 8th consecutive “dominant“ bit following a passive error flag. After each sequence of additional 8 consecutive ‘dominant’ bits. Increment by 8 Any other error condition (stuff, frame, CRC, ACK) Increment by 8 A valid reception or transmission Decrement by 1 unless counter is already 0 Obsolete

18.2.6 Bit Time Logic

Synchronization Jump Width can be configured by software. the various elements of a CAN bit time. positioned at the end of TSEG2. Figure 42. Bit Timing time quanta (tq) is defined by the TSEG2[3:0] bits. within the synchronization segment of each CAN bit time. This segment has the fixed length of one time quantum. either hard or soft synchronization (re-synchronization). frame with the falling edge on the bus while the bus is idle. This is interpreted as the SOF . It restarts the internal logic. chronization jump width (SJW). same effect as hard synchronization.

1 TIme

Figure 43. Resynchronization (e > SJW) Figure 44. Resynchronization (e < -SJW)

18.2.7 Clock Generator

the CKI input clock by the value defined in the CTIM register. the length of one time quantum (tq). for a detailed description of the CTIM register. Figure 45. CAN Prescaler

18.3 MESSAGE TRANSFER

bility to establish a BASIC-CAN path. one which matches the received message ID. triggering remote transmission request.

18.4 ACCEPTANCE FILTERING

the mask and the buffers controlled by the masks. Figure 46. Acceptance Filtering into the first buffer with a matching filtering mask. amples illustrate the difference. Figure 47. Acceptance of a Single Identifier Figure 48. Acceptance of a Group of Identifiers “don’t care” bits in the buffer ID). quent messages to be received by this buffer.

buffers use the same acceptance filtering mask). sage. The first incoming frame will be received by buffer 0. Figure 49. Message Storage with BUFFLOCK Enabled

18.5 RECEIVE STRUCTURE

Figure 50. Receive Buffer the different types of frames. ule will not try to match the frame to any subsequent buffer.

swer Remote Frames on page 106.

18.5.1 Receive Timing

Figure 51. Receive Timing immediately after the data bytes are copied into the buffer. resulting update from the CAN module. ing buffer are disabled with the exception of the status field. status is updated by the CAN module as shown in Table 39. states are explained in RX Buffer States on page 105.

18.5.2 Receive Procedure

message buffer for the reception of a CAN message.

1. Configure the receive masks (GMASK or BMASK).
2. Configure the message buffer status as RX_READY .

1 BIT

3 BIT

7 BIT

2 BIT

16 BIT

Figure 52. Buffer Read Routine (BUFFLOCK Disabled)

1. Read the status (CNSTAT) of the receive buffer. If the
2. Read the status to determine if a new message has
3. Write RX_READY into CNSTAT.
4. Read the ID/data and object control (DLC/RTR) from
5. Read the buffer status again and check it is not
6. If the buffer status is RX_FULL or RX_OVERRUN, one
7. If status is still RX_READY (as set by the CPU at step

2), clear interrupt pending bit and exit. Figure 53. Buffer Read Routine (BUFFLOCK Enabled)

1. Read the ID/data and object control (DLC/RTR) from
2. Write RX_READY into CNSTAT.
3. Clear interrupt pending bit and exit.

18.5.3 RX Buffer States

18.6 TRANSMIT STRUCTURE

the CPU has canceled the transmission request. configured to transmit a remote frame (RTR = 1). write TX_RTR in the status code register again.

18.6.1 Transmit Scheduling

as the transmission of the next frame has not yet started. Figure 54. Data Transmission the TX process is executed again.

18.6.2 Transmit Priority

ber results in the highest transmit priority. with the lower buffer number will have the higher priority.

18.6.3 Transmit Procedure

1. Configure the CNSTAT status field as

mission is aborted by an error.

1. Load buffer identifier and data registers. (For remote
2. Configure the CNSTAT status field to the desired value:

frame to trigger consecutive data frames. transmitted automatically without further CPU activity. Figure 55. Buffer Write Routine

000 H ighest

18.6.4 TX Buffer States

Figure 56. Transmit Buffer States

18.7 INTERRUPTS

rupt process can be initiated from the following sources. ting the flags in the CICLR registers.

18.7.1 Highest Priority Interrupt Code

bit in the CAN Interrupt Clear register (CICLR). Figure 57 shows the CAN interrupt management. Figure 57. Interrupt Management bits IRQ and IST3:0 as shown in T able 42.

18.7.2 Usage Hints

terrupt requests according to their priorities.

18.8 TIME STAMP COUNTER

Figure 58. Time Stamp Counter be enabled or disabled using the CGCR.TSTPEN bit.

www.national.com 110 CP3BT23

18.9 MEMORY ORGANIZATION

Each CAN module occupies 144 words in the memory ad- dress space. This space is organized as 15 banks of 8 words per bank (plus one reserved bank) for the message buffers and 14 words (plus 2 reserved words) for control and status.

18.9.1 CPU Access to CAN Registers/Memory

All memory locations occupied by the message buffers are shared by the CPU and CAN module (dual-ported RAM). The CAN module and the CPU normally have single-cycle access to this memory. However, if an access contention oc- curs, the access to the memory is blocked every cycle until the contention is resolved. This internal access arbitration is transparent to software. Both word and byte access to the buffer RAM are allowed. If a buffer is busy during the reception of an object (copy process from the hidden receive buffer) or is scheduled for transmission, the CPU has no write access to the data con- tents of the buffer. Write to the status/control byte and read access to the whole buffer is always enabled. All configuration and status registers can either be access- ed by the CAN module or the CPU only. These registers pro- vide single-cycle word and byte access without any potential wait state. All register descriptions within the next sections have the fol- lowing layout:

18.9.2 Message Buffer Organization

The message buffers are the communication interfaces be- tween CAN and the CPU for the transmission and the re- ception of CAN frames. There are 15 message buffers located at fixed addresses in the RAM location. As shown in Table 43, each buffer consists of two words reserved for the identifiers, 4 words reserved for up to eight CAN data bytes, one word reserved for the time stamp, and one word for data length code, transmit priority code, and the buffer status codes. 15 0 Bit/Field Names Reset Value CPU Access (R = read only, W = write only, R/W = read/write) Table 43 Message Buffer Map Address Buffer Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0E F0XEh ID1 XI[28:18]/ID[10:0] SRR /RTR IDE XI[17:15] 0E F0XCh ID0 XI[14:0] RTR 0E F0XAh DAT A0 Data1[7:0] Data2[7:0] 0E F0X8h DAT A1 Data3[7:0] Data4[7:0] 0E F0X6h DAT A2 Data5[7:0] Data6[7:0] 0E F0X4h DAT A3 Data7[7:0] Data8[7:0] 0E F0X2h TSTP TSTP[15:0] 0E F0X0h CNSTAT DLC Reserved PRI ST Obsolete

111 www.national.com CP3BT23

18.10 CAN CONTROLLER REGISTERS

Table 44 lists the CAN registers.

18.10.1 Buffer Status/Control Register (CNSTAT)

The buffer status (ST), the buffer priority (PRI), and the data length code (DLC) are controlled by manipulating the con- tents of the Buffer Status/Control Register (CNST AT). The CPU and CAN module have access to this register. ST The Buffer Status field contains the status in- formation of the buffer as shown in Table 45. This field can be modified by the CAN module. The ST0 bits acts as a buffer busy indication. When the BUSY bit is set, any write access to the buffer is disabled with the exception of the lower byte of the CNSTAT register. The CAN module sets this bit if the buffer data is cur- rently copied from the hidden buffer or if a message is scheduled for transmission or is currently transmitting. The CAN module al- ways clears this bit on a status update. Table 44 CAN Controller Registers Name Address Description CNSTAT See Table 43 CAN Buffer Status/ Control Register CGCR0 0E F100h CAN Global Configuration Register 0 CTIM0 0E F102h CAN Timing Register 0 GMSKX0 0E F104h Global Mask Register 0 GMSKB0 0E F106h Global Mask Register 0 BMSKX0 0E F108h Basic Mask Register 0 BMSKB0 0E F10Ah Basic Mask Register 0 CIEN0 0E F10Ch CAN Interrupt Enable Register 0 CIPND0 0E F10Eh CAN Interrupt Pending Register 0 CICLR0 0E F110h CAN Interrupt Clear Register 0 CICEN0 0E F112h CAN Interrupt Code Enable Register 0 CSTPND0 0E F114h CAN Status Pending Register 0 CANEC0 0E F116h CAN Error Counter Register 0 CEDIAG0 0E F118h CAN Error Diagnostic Register 0 CTMR0 0E F11Ah CAN Timer Register 0 CGCR1 0E F300h CAN Global Configuration Register 1 CTIM1 0E F302h CAN Timing Register 1 GMSKX1 0E F304h Global Mask Register 1 GMSKB1 0E F306h Global Mask Register 1 BMSKX1 0E F308h Basic Mask Register 1 BMSKB1 0E F30Ah Basic Mask Register 1 CIEN1 0E F30Ch CAN Interrupt Enable Register 1 CIPND1 0E F30Eh CAN Interrupt Pending Register 1 CICLR1 0E F310h CAN Interrupt Clear Register 1 CICEN1 0E F312h CAN Interrupt Code Enable Register 1 CSTPND1 0E F314h CAN Status Pending Register 1 CANEC1 0E F316h CAN Error Counter Register 1 CEDIAG1 0E F318h CAN Error Diagnostic Register 1 CTMR1 0E F31Ah CAN Timer Register 1 15 12 11 8 7 4 3 0 DLC Reserved PRI ST R/W Table 44 CAN Controller Registers Name Address Description Obsolete

www.national.com 112 CP3BT23 Table 45 Buffer Status Section of the CNSTAT Register ST3 (DIR) ST2 ST1 ST0 (BUSY) Buffer Status 0 0 0 0 RX_NOT_ACTIVE 00 0 1 Reserved for RX_BUSY . (This condition indicates that soft- ware wrote RX_NOT_ACTIVE to a buffer when the data copy process is still active.) 0 0 1 0 RX_READY 00 1 1 RX_BUSY0 (Indicates data is being copied for the first time RX_READY → RX_BUSY0.) 0 1 0 0 RX_FULL 01 0 1 RX_BUSY1 (Indicates data is being copied for the second time RX_FULL → RX_BUSY1.) 0 1 1 0 RX_OVERRUN 01 1 1 RX_BUSY2 (Indicates data is being copied for the third or subsequent times RX_OVERRUN → RX_BUSY2.) 10 0 0 T X_N O T_AC TIVE 10 0 1 Reserved for TX_BUSY . (This state indicates that software wrote TX_NOT_ACTIVE to a transmit buffer which is sched- uled for transmission or is currently transmitting.) 1 1 0 0 TX_ONCE 11 0 1 TX_BUSY0 (Indicates that a buffer is scheduled for trans- mission or is actively transmitting; it can be due to one of two cases: a message is pending for transmission or is cur- rently transmitting, or an automated answer is pending for transmission or is currently transmitting.) 1 0 1 0 TX_RTR (Automatic response to a remote frame.) 1 0 1 1 Reserved for TX_BUSY1. (This condition does not occur.) 1 1 1 0 TX_ONCE_RTR (Changes to TX_RTR after transmission.) 11 1 1 TX_BUSY2 (Indicates that a buffer is scheduled for trans- mission or is actively transmitting; it can be due to one of two cases: a message is pending for transmission or is cur- rently transmitting, or an automated answer is pending for transmission or is currently transmitting.) Obsolete

113 www.national.com CP3BT23 PRI The Transmit Priority Code field holds the software-defined transmit priority code for the message buffer. DLC The Data Length Code field determines the number of data bytes within a received/trans- mitted frame. For transmission, these bits need to be set according to the number of data bytes to be transmitted. For reception, these bits indicate the number of valid re- ceived data bytes available in the message buffer. Table 46 shows the possible bit combi- nations for DLC3:0 for data lengths from 0 to 8 bytes. Note: The maximum number of data bytes received/trans- mitted is 8, even if the DLC field is set to a value greater than 8. Therefore, if the data length code is greater or equal to eight bytes, the DLC field is ignored.

18.10.2 Storage of Standard Messages

During the processing of standard frames, the Extended- Identifier (IDE) bit is clear. The ID1[3:0] and ID0[15:0] bits are “don’t care” bits. A standard frame with eight data bytes is shown in Table 47. IDE The Identifier Extension bit determines wheth- er the message is a standard frame or an ex- tended frame. 0 – Message is a standard frame using 11 identifier bits. 1 – Message is an extended frame. RTR The Remote Transmission Request bit indi- cates whether the message is a data frame or a remote frame. 0 – Message is a data frame. 1 – Message is a remote frame. ID The ID field is used for the 11 standard frame identifier bits. Table 46 Data Length Coding DLC Number of Data Bytes 0000 0 0001 1 0010 2 0011 3 0100 4 0101 5 0110 6 0111 7 1000 8 Table 47 Standard Frame with 8 Data Bytes Address Buffer Register 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 0E F0XEh ID1 ID[10:0] RTR IDE Don ’t Care 0E F0XCh ID0 Don ’t Care 0E F0XAh DATA0 Data1[7:0] Data2[7:0] 0E F0X8h DATA1 Data3[7:0] Data4[7:0] 0E F0X6h DATA2 Data5[7:0] Data6[7:0] 0E F0X4h DATA3 Data7[7:0] Data8[7:0] 0E F0X2h TSTP TSTP[15:0] 0E F0X0h CNSTAT DLC Reserved PRI ST Obsolete

18.10.3 Storage of Messages with Less Than 8 Data

in these bytes will be overwritten with invalid data.

18.10.4 Storage of Extended Messages

Table 48. The SRR bit is at the bit position of the RTR bit for standard frame and needs to be transmitted as 1. received as monitored on the CAN bus. 1 – Message is an extended frame. 0 – Message is a data frame. 1 – Message is a remote frame.

115 www.national.com CP3BT23

18.10.5 Storage of Remote Messages

During remote frame transfer, the buffer registers DATA0– DATA3 are “don’t cares”. If a remote frame is transmitted, the contents of these registers are ignored. If a remote frame is received, the contents of these registers will be overwritten with invalid data. The structure of a message buffer set up for a remote frame with extended identifier is shown in Table 49. SRR The Substitute Remote Request bit replaces the RTR bit used in standard frames at this bit position. The SRR bit needs to be set by soft- ware. IDE The Identifier Extension bit determines wheth- er the message is a standard frame or an ex- tended frame. 0 – Message is a standard frame using 11 identifier bits. 1 – Message is an extended frame. RTR The Remote Transmission Request bit indi- cates whether the message is a data frame or a remote frame. 0 – Message is a data frame. 1 – Message is a remote frame. ID The ID field is used to build the 29-bit identifier of an extended frame. The ID[28:18] field is used for the 11 standard frame identifier bits. Table 49 Extended Remote Frame Address Buffer Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0E F0XEh ID1 ID[28:18] SRR IDE ID17:15] 0E F0XCh ID0 ID[14:0] RTR 0E F0XAh DATA0 Don ’t Care 0E F0X8h DAT A1 0E F0X6h DAT A2 0E F0X4h DAT A3 0E F0X2h TSTP TSTP 0E F0X0h CNSTAT DLC Reserved PRI ST Obsolete

www.national.com 116 CP3BT23

18.10.6 CAN Global Configuration Register (CGCRn)

The CGCRn register is a 16-bit wide register used to: ! Enable/disable the CAN module. ! Configure the BUFFLOCK function for the message buff- er 0..14. ! Enable/disable the time stamp synchronization. ! Set the logic levels of the CAN Input/Output pins, CAN- RX and CANTX. ! Choose the data storage direction (DDIR). ! Select the error interrupt type (EIT). ! Enable/disable diagnostic functions. CANEN The CAN Enable bit enables/disables the CAN module. When the CAN module is dis- abled, all internal states and the TEC and REC counter registers are cleared. In addition the CAN module clock is disabled. All CAN module control registers and the contents of the object memory are left unchanged. Soft- w a r e m u s t m a k e s u r e t h a t n o m e s s a g e i s pending for transmission before the CAN module is disabled. 0 – CAN module is disabled. 1 – CAN module is enabled. CTX The Control Transmit bit configures the logic level of the CAN transmit pin CANTX. 0 – Dominant state is 0; recessive state is 1. 1 – Dominant state is 1; recessive state is 0. CRX The Control Receive bit configures the logic level of the CAN receive pin CANRX. 0 – Dominant state is 0; recessive state is 1. 1 – Dominant state is 1; recessive state is 0. BUFFLOCK The Buffer Lock bit configures the buffer lock function. If this feature is enabled, a buffer will be locked upon a successful frame reception. The buffer will be unlocked again by writing RX_READY in the buffer status register, i.e., after reading data. 0 – Lock function is disabled for all buffers. 1 – Lock function is enabled for all buffers. TSTPEN The Time Sync Enable bit enables or disables the time stamp synchronization function of the CAN module. 0 – Time synchronization disabled. The Time Stamp counter value is not reset upon re- ception or transmission of a message to/ from buffer 0. 1 – Time synchronization enabled. The Time Stamp counter value is reset upon recep- tion or transmission of a message to/from buffer 0. DDIR The Data Direction bit selects the direction the data bytes are transmitted and received. The CAN module transmits and receives the CAN Data1 byte first and the Data8 byte last (Data1, Data2,...,Data7, Data8). If the DDIR bit is clear, the data contents of a received message is stored with the first byte at the highest data address and the last data at the lowest data address (see Figure 59). The same applies for transmitted data. 0 – First byte at the highest address, subse- quent bytes at lower addresses. 1 – First byte at the lowest address, subse- quent bytes at higher addresses. 7 6 5 4 3 2 1 0 IGNACK LO DDIR TST PEN BUFF LOCK CRX CTX CANEN R/W 15 12 11 10 9 8 Reserved EIT DIAGEN INTERNAL LOOPBACK R/W Obsolete

www.national.com 118 CP3BT23 INTERNAL If the Internal function is enabled, the CANTX and CANRX pins of the CAN module are inter- nally connected to each other. This feature can be used in conjunction with the LOOP- BACK mode. This means that the CAN mod- ule can receive its own sent messages without connecting an external transceiver chip to the CANTX and CANRX pins; it allows software to run real stand-alone tests without any peripheral devices. 0 – Normal mode. 1 – Internal mode. DIAGEN The Diagnostic Enable bit globally enables or disables the special diagnostic features of the CAN module. This includes the following func- tions:  LO (Listen Only).  IGNACK (Ignore Acknowledge).  LOOPBACK (Loopback).  INTERNAL (Internal Loopback).  Write access to hidden receive buffer. 0 – Normal mode. 1 – Diagnostic features enabled. EIT The Error Interrupt Type bit configures when the Error Interrupt Pending Bit (CIPND.EIP- ND) is set and an error interrupt is generated if enabled by the Error Interrupt Enable (CIEN.EIEN). 0 – The EIPND bit is set on every error on the CAN bus. 1 – The EIPND bit is set only if the error state (CSTPND.NS) changes as a result of in- crementing either the receive or transmit error counter.

18.10.7 CAN Timing Register (CTIM)

The Can Timing Register (CTIM) defines the configuration of the Bit Time Logic (BTL). PSC The Prescaler Configuration field specifies the CAN prescaler. The settings are shown in Table 50 SJW The Synchronization Jump Width field speci- fies the Synchronization Jump Width, which can be programmed between 1 and 4 time quanta (see Table 51). Note: The settings of SJW must be configured to be small- er or equal to TSEG1 and TSEG2 15 9 8 7 6 3 2 0 PSC SJW TSEG1 TSEG2 R/W Table 50 CAN Prescaler Settings PSC6:0 Prescaler 000000 2 000001 3 000010 4 000011 5 000100 6 1111101 127 1111110 128 1111111 128 Table 51 SJW Settings SJW Synchronization Jump Width (SJW) 00 1 time quantum 01 2 time quanta 10 3 time quanta 11 4 time quanta Obsolete

119 www.national.com CP3BT23 TSEG1 The Time Segment 1 field configures the length of the Time Segment 1 (TSEG1). It is not recommended to configure the time seg- ment 1 to be smaller than 2 time quanta. (see Table 52). TSEG2 The Time Segment 2 field specifies the num- ber of time quanta (tq) for phase segment 2 (see Table 53).

18.10.8 Global Mask Register (GMSKBn/GMSKXn)

The GMSKBn and GMSKXn registers allow software to glo- bally mask, or “don’t care” the incoming extended/standard identifier bits, RTR/XRTR and IDE. Throughout this docu- ment, the GMSKBn and GMSKXn 16-bit registers are refer- enced as a 32-bit register GMSK. The following are the bits for the GMSKBn register. The following are the bits for the GMSKXn register. For all GMSKBn and GMSKXn register bits, the following applies: 0 – The incoming identifier bit must match the correspond- ing bit in the message buffer identifier register. 1 – Accept 1 or 0 (“don’t care”) in the incoming ID bit inde- pendent from the corresponding bit in the message buffer ID registers. The corresponding ID bit in the mes- sage buffer will be overwritten by the incoming identifier bits. When an extended frame is received from the CAN bus, all GMSK bits GM28:0, IDE, RTR, and XRTR are used to mask the incoming message. In this case, the RTR bit in the GMSK register corresponds to the SRR bit in the message. The XRTR bit in the GMSK register corresponds to the RTR bit in the message. During the reception of standard frames only the GMSK bits GM[28:18], RTR, and IDE are used. In this case, the GM[28:18] bits in the GMSK register correspond to the ID[10:0] bits in the message. Table 52 Time Segment 1 Settings TSEG1[3:0] Length of Time (TSEG1)

0000 Not recommended

Table 53 Time Segment 2 Settings TSEG2 Length of TSEG2 000 1 time quantum 001 2 time quanta 010 3 time quanta 011 4 time quanta 100 5 time quanta 101 6 time quanta 110 7 time quanta 111 8 time quanta 15 5 4 3 2 0 GM28:18 RTR IDE GM17:15 R/W 15 1 0 GM14:0 XRTR R/W Global Mask GM[28:18] RTR IDE GM[17:0] XRTR Standard Frame ID[10:0] RTR IDE Unused Extended Frame ID[28:18] SRR IDE ID[17:0] RTR Obsolete

www.national.com 120 CP3BT23

18.10.9 Basic Mask Register (BMSKBn/BMSKXn)

The BMSKBn and BMSKXn registers allow masking the buffer 14, or “don’t care” the incoming extended/standard identifier bits, RTR/XRTR, and IDE. Throughout this docu- ment, the two 16-bit registers BMSKBn and BMSKXn are referenced to as a 32-bit register BMSK. The following are the bits for the BMSKB register. The following are the bits for the BMSKX register. For all BMSKBn and BMSKXn register bits the following ap- plies: 0 – The incoming identifier bit must match the correspond- ing bit in the message buffer identifier register. 1 – Accept 1 or 0 (“don’t care”) in the incoming ID bit inde- pendent from the corresponding bit in the message buffer ID registers. The corresponding ID bit in the mes- sage buffer will be overwritten by the incoming identifier bits. When an extended frame is received from the CAN bus, all BMSK bits BM28:0, IDE, RTR, and XRTR are used to mask the incoming message. In this case, the RTR bit in the BMSK register corresponds to the SRR bit in the message. The XRTR bit in the BMSK register corresponds to the RTR bit in the message. During the reception of standard frames, only the BMSK bits BM[28:18], RTR, and IDE are used. In this case, the BM[28:18] bits in the BMSK register correspond to the ID[10:0] bits in the message.

18.10.10 CAN Interrupt Enable Register (CIENn)

The CIENn register enables the transmit/receive interrupts of the message buffers 0 through 14 as well as the CAN Er- ror Interrupt. EIEN The Error Interrupt Enable bit allows the CAN module to interrupt the CPU if any kind of CAN receive/transmit errors are detected. This causes any error status change in the er- ror counter registers REC/TEC is able to gen- erate an error interrupt. 0 – The error interrupt is disabled and no er- ror interrupt will be generated. 1 – The error interrupt is enabled and a change in REC/TEC will cause an inter- rupt to be generated. IEN The Buffer Interrupt Enable bits allow software to enable/disable the interrupt source for the corresponding message buffer. For example, IEN14 controls interrupts from buffer14, and IEN0 controls interrupts from buffer0. 0 – Buffer as interrupt source disabled. 1 – Buffer as interrupt source enabled.

18.10.11 CAN Interrupt Pending Register (CIPNDn)

The CIPNDn register indicates any CAN Receive/Transmit Interrupt Requests caused by the message buffers 0..14 and CAN error occurrences. EIPND The Error Interrupt Pending field indicates the status change of TEC/REC and will execute an error interrupt if the EIEN bit is set. Soft- ware has the responsibility to clear the EIPND bit using the CICLRn register. 0 – CAN status is not changed. 1 – CAN status is changed. IPND The Buffer Interrupt Pending bits are set by the CAN module following a successful trans- mission or reception of a message to or from the corresponding message buffer. For exam- ple, IPND14 corresponds to buffer14, and IPND0 corresponds to buffer0. 0 – No interrupt pending for the correspond- ing message buffer. 1 – Message buffer has generated an inter- rupt. 15 5 4 3 2 0 BM28:18 RTR IDE BM17:15 R/W 15 1 0 BM14:0 XRTR R/W Basic Mask BM28:18 RTR IDE BM17:0 XRTR Standard Frame ID10:0 RTR IDE Unused Extended Frame ID28:18 SRR IDE ID17:0 RTR 15 14 0 EIEN IEN R/W 15 14 0 EIPND IPND R Obsolete

121 www.national.com CP3BT23

18.10.12 CAN Interrupt Clear Register (CICLRn)

The CICLRn register bits individually clear CAN interrupt pending flags caused by the message buffers and from the Error Management Logic. Do not modify this register with in- structions that access the register as a read-modify-write operand, such as the bit manipulation instructions. EICLR The Error Interrupt Clear bit is used to clear the EIPND bit. 0 – The EIPND bit is unaffected by writing 0. 1 – The EIPND bit is cleared by writing 1. ICLR The Buffer Interrupt Clear bits are used to clear the IPND bits. 0 – The corresponding IPND bit is unaffected by writing 0. 0 – The corresponding IPND bit is cleared by writing 1.

18.10.13 CAN Interrupt Code Enable Register (CICENn)

The CICENn register controls whether the interrupt pending flag in the CIPNDn register is translated into the Interrupt Code field of the CSTPNDn register. All interrupt requests, CAN error, and message buffer interrupts can be enabled/ disabled separately for the interrupt code indication field. EICEN The Error Interrupt Code Enable bit controls encoding for error interrupts. 0 – Error interrupt pending is not indicated in the interrupt code. 1 – Error interrupt pending is indicated in the interrupt code. ICEN The Buffer Interrupt Code Enable bits control encoding for message buffer interrupts. 0 – Message buffer interrupt pending is not indicated in the interrupt code. 1 – Message buffer interrupt pending is indi- cated in the interrupt code.

18.10.14 CAN Status Pending Register (CSTPNDn)

The CSTPNDn register holds the status of the CAN Node and the Interrupt Code. NS The CAN Node Status field indicates the sta- tus of the CAN node as shown in Table 54. IRQ/IST The IRQ bit and IST field indicate the interrupt source of the highest priority interrupt current- ly pending and enabled in the CICENn regis- ter. Table 55 shows the several interrupt codes when the encoding for all interrupt sources is enabled (CICEN = FFFFh). 15 14 0 EICLR ICLR W 15 14 0 EICEN ICEN R/W 15 8 7 5 4 3 0 Reserved NS IRQ IST R Table 54 CAN Node Status NS Node Status

000 Not Active

010 Error Active

011 Error Warning Level

Table 55 Highest Priority Interrupt Code IRQ IST3:0 CAN Interrupt Request 0 0000 No interrupt request 1 0000 Error interrupt 1 0001 Buffer 0 1 0010 Buffer 1 1 0011 Buffer 2 1 0100 Buffer 3 1 0101 Buffer 4 1 0110 Buffer 5 1 0111 Buffer 6 1 1000 Buffer 7 1 1001 Buffer 8 1 1010 Buffer 9 1 1011 Buffer 10 1 1100 Buffer 11 1 1101 Buffer 12 1 1110 Buffer 13 1 1111 Buffer 14 Obsolete

18.10.15 CAN Error Counter Register (CANECn)

ceive Error Counter and the CAN T ransmit Error Counter. the value of the receive error counter. the value of the transmit error counter.

18.10.16 CAN Error Diagnostic Register (CEDIAGn)

this register, and all bits are cleared on reset. frame field in which the last error occurred. Figure 61. EBID Example 1110b and the EBID field shows 111001b. This means the faulty field was the data field. ter at the time the error occurred.

0000 ERROR

0001 ERROR DEL

0010 ERROR ECHO

0011 BUS IDLE

0100 ACK

0101 EOF

0110 INTERMISSION

0111 SUSPEND

1000 SOF

1001 ARBITRATION

1010 IDE

1011 EXTENDED

1100 R1/R0

1101 DLC

1110 DATA

1111 CRC

ACK and during an active error flag.

18.10.17 CAN Timer Register (CTMRn)

Stamp Counter as described in Section 18.8. transfer of the message buffer 0.

18.11 SYSTEM START-UP AND MULTI-INPUT

! Configure every buffer to its function as receive/transmit. tion Register (CGCRn)” on page 116. that no transmission is still pending.

18.11.1 External Connection

vide the functionality described in Table 57. Global Configuration Register (CGCRn)” on page 116).

18.11.2 Transceiver Connection

Figure 62. External Transceiver

18.11.3 Timing Requirements

Table 58. These requirements may lead to some restrictions

5 REF

4 RX1 TX

www.national.com 124 CP3BT23 The critical path derives from receiving a remote frame, which triggers the transmission of one or more data frames. There are a minimum of four bit times in-between two con- secutive frames. These bit times start at the validation point of received frame (reception of 6th EOF bit) and end at the earliest possible transmission start of the next frame, which is after the third intermission bit at 100% burst bus load. These four bit times have to be set in perspective with the timing requirements of the CAN module. The minimum duration of the four CAN bit times is deter- mined by the following Bit Time Logic settings: PSC = PSCmin = 2 TSEG1 = TSEG1min = 2 TSEG2 = TSEG2min = 1 Bit time = Sync + Time Segment 1 + Time Segment 2 = (4 tq × PSC) clock cycles = (4 tq × 2) clock cycles = 8 clock cycles For these minimum BTL settings, four CAN bit times take 32 clock cycles. The following is an example that assumes typical case: ! Minimum BTL settings ! Reception and copy of a remote frame ! Update of one buffer from TX_RTR ! Schedule of one buffer from transmit As outlined in Table 58, the copy process, update, and scheduling the next transmission gives a total of 17 + 3 + 2 = 22 clock cycles. Therefore under these conditions there is no timing restriction. The following example assumes the worst case: ! Minimum BTL settings ! Reception and copy of a remote frame ! Update of the 14 remaining buffers from TX_RTR ! Schedule of one buffer for transmit All these actions in total require 17 + (14 × 3) + 2 = 61 clock cycles to be executed by the CAN module. This leads to the limitation of the Bit Time Logic of 61 / 4 = 15.25 clock cycles per CAN bit as a minimum, resulting in the minimum clock frequencies listed below. (The frequency depends on the desired baud rate and assumes the worst case scenario can occur in the application.) Table 59 gives examples for the minimum clock frequency in order to ensure proper functionality at various CAN bus speeds.

18.11.4 Bit Time Logic Calculation Examples

The calculation of the CAN bus clocks using CKI = 16 MHz is shown in the following examples. The desired baud rate for both examples is 1 Mbit/s. Example 1 TSEG1 = TSEG1[3:0] + 1 = 3 + 1 = 4 TSEG2 = TSEG2[2:0] + 1 = 2 + 1 = 3 SJW = TSEG2 = 3 ! Sample point positioned at 62.5% of bit time ! Bit time = 125 ns × (1 + 4 + 3 ± 3) = (1 ± 0.375) µs ! Bus Clock = 16 MHz / (2 × (1 + 4 + 3)) = 1 Mbit/s (nomi- nal) Example 2 TSEG1 = TSEG1[3:0] + 1 = 1 + 1 = 2 TSEG2 = TSEG2[2:0] + 1 = 0 + 1 = 1 SJW = TSEG2 = 1 ! Sample point positioned at 75% of bit time ! Bit time = 250 ns × (1 + 2 + 1 ± 1) = (1 ± 0.25) µs ! Bus Clock = 16 MHz / (2 × (1 + 4 + 3)) = 1Mbit/s (nominal)

18.11.5 Acceptance Filter Considerations

The CAN module provides two acceptance filter masks GMSK and BMSK, as described in “Acceptance Filtering” on page 102, “Global Mask Register (GMSKBn/GMSKXn)” on page 119, and “Basic Mask Register (BMSKBn/BM- SKXn)” on page 120. These masks allow filtering of up to 32 bits of the message object, which includes the standard identifier, the extended identifier, and the frame control bits RTR, SRR, and IDE.

18.11.6 Remote Frames

Remote frames can be automatically processed by the CAN module. However, to fully enable this feature, the RTR/ XRTR bits (for both standard and extended frames) within the BMSK and/or GMSK register need to be set to “don’t care”. This is because a remote frame with the RTR bit set should trigger the transmission of a data frame with the RTR bit clear and therefore the ID bits of the received message need to pass through the acceptance filter. The same ap- plies to transmitting remote frames and switching to receive the corresponding data frames. Table 58 CAN Module Internal Timing Task Cycle Count Occurrence/ Frame Copy hidden buffer to receive message buffer 17 0 –1 Update status from TX_RTR to TX_ONCE_RTR 30 –15 Schedule a message for transmission 20 –1 Table 59 Minimum Clock Frequency Requirements Baud Rate Minimum Clock Frequency 1 Mbit/sec 15.25 MHz 500 kbit/sec 7.625 MHz 250 kbit/sec 3.81 MHz Obsolete

125 www.national.com CP3BT23

18.12 USAGE HINT

Under certain conditions, the CAN module receives a frame sent by itself, even though the loopback feature is disabled. Two conditions must be true to cause this malfunction: ! A transmit buffer and at least one receive buffer are con- figured with the same identifier. Assume this identifier is called ID_RX_TX. With regard to the receive buffer, this means that the buffer identifier and the corresponding fil- ter masks are set up in a way that the buffer is able to re- ceive frames with the identifier ID_RX_TX. ! The following sequence of events occurs: 1. A message with the identifier ID_RX_TX from an- other CAN node is received into the receive buffer. 2. A message with the identifier ID_RX_TX is sent by the CAN module immediately after the reception took place. When these conditions occur, the frame sent by the CAN module will be copied into the next receive buffer available for the identifier ID_RX_TX. If a frame with an identifier different to ID_RX_TX is sent or received in between events 1 and 2, the problem does not occur. Obsolete

www.national.com 126 CP3BT23

19.0 Advanced Audio Interface

The Advanced Audio Interface (AAI) provides a serial syn- chronous, full duplex interface to codecs and similar serial devices. The transmit and receive paths may operate asyn- chronously with respect to each other. Each path uses a 3- wire interface consisting of a bit clock, a frame synchroniza- tion signal, and a data signal. The CPU interface can be either interrupt-driven or DMA. If the interface is configured for interrupt-driven I/O, data is buffered in the receive and transmit FIFOs. If the interface is configured for DMA, the data is buffered in registers. The AAI is functionally similar to a Motorola TM Synchronous Serial Interface (SSI). Compared to a standard SSI imple- mentation, the AAI interface does not support the so-called “On-demand Mode”. It also does not allow gating of the shift clocks, so the receive and transmit shift clocks are always active while the AAI is enabled. The AAI also does not sup- port 12- and 24-bit data word length or more than 4 slots (words) per frame. The reduction of supported modes is ac- ceptable, because the main purpose of the AAI is to connect to audio codecs, rather than to other processors (DSPs). The implementation of a FIFO as a 16-word receive and transmit buffer is an additional feature, which simplifies communication and reduces interrupt load. Independent DMA is provided for each of the four supported audio chan- nels (slots). The AAI also provides special features and op- erating modes to simplify gain control in an external codec and to connect to an ISDN controller through an IOM-2 compatible interface.

19.1 AUDIO INTERFACE SIGNALS

19.1.1 Serial Transmit Data (STD)

The STD pin is used to transmit data from the serial transmit shift register (ATSR). The STD pin is an output when data is being transmitted and is in high-impedance mode when no data is being transmitted. The data on the STD pin changes on the positive edge of the transmit shift clock (SCK). The STD pin goes into high-impedance mode on the negative edge of SCK of the last bit of the data word to be transmit- ted, assuming no other data word follows immediately. If an- other data word follows immediately, the STD pin remains active rather than going to the high-impedance mode.

19.1.2 Serial Transmit Clock (SCK)

The SCK pin is a bidirectional signal that provides the serial shift clock. In asynchronous mode, this clock is used only by the transmitter to shift out data on the positive edge. The se- rial shift clock may be generated internally or it may be pro- vided by an external clock source. In synchronous mode, the SCK pin is used by both the transmitter and the receiver. Data is shifted out from the STD pin on the positive edge, and data is sampled on the SRD pin on the negative edge.

19.1.3 Serial Transmit Frame Sync (SFS)

The SFS pin is a bidirectional signal which provides frame synchronization. In asynchronous mode, this signal is used as frame sync only by the transmitter. In synchronous mode, this signal is used as frame sync by both the transmitter and receiver. The frame sync signal may be generated internally, or it may be provided by an external source.

19.1.4 Serial Receive Data (SRD)

The SRD pin is used as an input when data is shifted into the Audio Receive Shift Register (ARSR). In asynchronous mode, data on the SRD pin is sampled on the negative edge of the serial receive shift clock (SRCLK). In synchronous mode, data on the SRD pin is sampled on the negative edge of the serial shift clock (SCK). The data is shifted into ARSR with the most significant bit (MSB) first.

19.1.5 Serial Receive Clock (SRCLK)

The SRCLK pin is a bidirectional signal that provides the re- ceive serial shift clock in asynchronous mode. In this mode, data is sampled on the negative edge of SRCLK. The SR- CLK signal may be generated internally or it may be provid- ed by an external clock source. In synchronous mode, the SCK pin is used as shift clock for both the receiver and transmitter, so the SRCLK pin is available for use as a gen- eral-purpose port pin or an auxiliary frame sync signal to ac- cess multiple slave devices (e.g. codecs) within a network (see Network mode).

19.1.6 Serial Receive Frame Sync (SRFS)

The SRFS pin is a bidirectional signal that provides frame synchronization for the receiver in asynchronous mode. The frame sync signal may be generated internally, or it may be provided by an external source. In synchronous mode, the SFS signal is used as the frame sync signal for both the transmitter and receiver, so the SRFS pin is available for use as a general-purpose port pin or an auxiliary frame sync sig- nal to access multiple slave devices (e.g. codecs) within a network (see Network mode).

19.2 AUDIO INTERFACE MODES

There are two clocking modes: asynchronous mode and synchronous mode. These modes differ in the source and timing of the clock signals used to transfer data. When the AAI is generating the bit shift clock and frame sync signals internally, synchronous mode must be used. There are two framing modes: normal mode and network mode. In normal mode, one word is transferred per frame. In network mode, up to four words are transferred per frame. A word may be 8 or 16 bits. The part of the frame which car- ries a word is called a slot. Network mode supports multiple external devices sharing the interface, in which each device is assigned its own slot. Separate frame sync signals are provided, so that each device is triggered to send or receive its data during its assigned slot.

19.2.1 Asynchronous Mode

In asynchronous mode, the receive and transmit paths of the audio interface operate independently, with each path using its own bit clock and frame sync signal. Independent clocks for receive and transmit are only used when the bit clock and frame sync signal are supplied externally. If the bit clock and frame sync signals are generated internally, both paths derive their clocks from the same set of clock prescal- ers. Obsolete

19.2.2 Synchronous Mode

are derived from the same set of clock prescalers.

19.2.3 Normal Mode

programmed to select slot 0. transmit DMA register 0 (ARDR0/ATDR0). mode with a long frame sync interval. Figure 63. Normal Mode Frame or less than a programmable warning limit. Figure 64. IRQ/DMA Support in Normal Mode In network mode, each frame is composed of multiple slots. up to four slots are supported by this audio interface. to it, in which only that device is allowed to transfer data. frame are reserved for other devices. transmit FIFO or the corresponding DMA transmit register.

Figure 67. Accessing Three Devices in Network Mode

19.3 BIT CLOCK GENERATION

to minimize the bit clock error, fbit_error. per second. The input clock of the audio interface is 12 MHz.

19.4 FRAME CLOCK GENERATION

used, the frame width must always be at least 16 bits wide. Frame Sync Length field (FSL) in the AGCR register.

19.5 AUDIO INTERFACE OPERATION

19.5.1 Clock Configuration

Aux1 clock by setting the ACE1 bit in the CRCTRL register.

19.5.2 Interrupts

Interrupt Control Unit (ICU). programmed to generate edge-triggered interrupts.

Figure 68 shows the interrupt structure of the AAI. Figure 68. AAI Interrupt Structure

19.5.3 Normal Mode

low byte of each 16-bit FIFO location holds valid data.

19.5.4 Transmit

beginning of a new frame is identified by a frame sync pulse. vious data will be re-transmitted. ed internally, or they can be supplied by an external source.

19.5.5 Receive

SRFS (or SFS in synchronous mode). overwritten with the new data.

131 www.national.com CP3BT23

19.5.6 Network Mode

In network mode, each frame sync signal marks the begin- ning of new frame. Each frame can consist of up to four slots. The audio interface operates in a similar way to nor- mal mode, however, in network mode the transmitter and re- ceiver can be assigned to specific slots within each frame as described below.

19.5.7 Transmit

The transmitter only shifts out data during the assigned slot. During all other slots the STD output is in TRI-STATE mode. DMA Operation When a complete data word has been transmitted through the STD pin, a new data word is reloaded from the corre- sponding transmit DMA register n (ATDRn). A DMA request is asserted when ATDRn is empty. If a new data word must be transmitted in a slot n while ATDRn is still empty, the pre- vious slot n data will be retransmitted. FIFO Operation When a complete data word has been transmitted through the STD pin, a new data word is reloaded from the transmit FIFO from the current location of the Transmit FIFO Read Pointer (TRP). After that, the TRP is automatically incre- mented by 1. Therefore, the audio data to be transmitted in the next slot of the frame is read from the next FIFO loca- tion. A write to the Audio Transmit FIFO Register (ATFR) results in a write to the transmit FIFO at the current location of the Transmit FIFO Write Pointer (TWP). After every write oper- ation to the transmit FIFO, the TWP is automatically incre- mented by 1. When the TRP is equal to the TWP and the last access to the FIFO was a read operation (transfer to the ATSR), the transmit FIFO is empty. When an additional read operation from the FIFO to the A TSR is performed (while the FIFO is already empty), a transmit FIFO underrun occurs. In this case, the read pointer (TRP) will be decremented by 1 (in- cremented by 15) and the previous data word will be trans- mitted again. A transmit FIFO underrun is indicated by the TXU bit in the Audio Interface Transmit Status and Control Register (ATSCR). No transmit interrupt will be generated (even if enabled). If the current TRP is equal to the TWP and the last access to the FIFO was a write operation (to the ATFR), the FIFO is full. If an additional write to the ATFR is performed, a trans- mit FIFO overrun occurs. This error condition is not prevent- ed by hardware. Software must ensure that no transmit overrun occurs. The transmit frame synchronization pulse on the SFS pin and the transmit shift clock on the SCK pin may be generat- ed internally, or they can be supplied by an external source.

19.5.8 Receive

The receive shift register (ARSR) receives data words of all slots in the frame, regardless of the slot assignment of the interface. However, only those ARSR contents are trans- ferred to the receive FIFO or DMA receive register which were received during the assigned time slots. A receive in- terrupt or DMA request is initiated when this occurs. DMA Operation When a complete data word has been received through the SRD pin in a slot n, the new data word is transferred to the corresponding receive DMA register n (ARDRn). A DMA re- quest is asserted when the ARDRn register is full. If a new slot n data word is received while the ARDRn register is still full, the ARDRn register will be overwritten with the new da- ta. FIFO Operation When a complete word has been received, it is transferred to the receive FIFO at the current location of the Receive FIFO Write Pointer (RWP). After that, the RWP is automati- cally incremented by 1. Therefore, data received in the next slot is copied to the next higher FIFO location. A read from the Audio Receive FIFO Register (ARFR) re- sults in a read from the receive FIFO at the current location of the Receive FIFO Read Pointer (RRP). After every read operation from the receive FIFO, the RRP is automatically incremented by 1. When the RRP is equal to the RWP and the last access to the FIFO was a transfer to the ARFR, the receive FIFO is full. When a new complete data word has been shifted into the ARSR while the receive FIFO was already full, the shift register overruns. In this case, the new data in the ARSR will not be transferred to the FIFO and the RWP will not be in- cremented. A receive FIFO overrun is indicated by the RXO bit in the Audio Interface Receive Status and Control Regis- ter (ARSCR). No receive interrupt will be generated (even if enabled). When the current RWP is equal to the TWP and the last ac- cess to the receive FIFO was a read from ARFR, a receive FIFO underrun has occurred. This error condition is not pre- vented by hardware. Software must ensure that no receive underrun occurs. The receive frame synchronization pulse on the SRFS pin (or SFS in synchronous mode) and the receive shift clock on the SRCLK (or SCK in synchronous mode) may be gener- ated internally, or they can be supplied by an external source.

19.6 COMMUNICATION OPTIONS

19.6.1 Data Word Length

The word length of the audio data can be selected to be ei- ther 8 or 16 bits. In 16-bit mode, all 16 bits of the transmit and receive shift registers (ATSR and ARSR) are used. In 8- bit mode, only the lower 8 bits of the transmit and receive shift registers (ATSR and ARSR) are used.

19.6.2 Frame Sync Signal

The audio interface can be configured to use either long or short frame sync signals to mark the beginning of a new data frame. If the corresponding Frame Sync Select (FSS) bit in the Audio Control and Status register is clear, the re- ceive and/or transmit path generates or recognizes short frame sync pulses with a length of one bit shift clock period. When these short frame sync pulses are used, the transfer of the first data bit or the first slot begins at the first positive edge of the shift clock after the negative edge on the frame sync pulse. Obsolete

amples of short and long frame sync pulses. Figure 69. Short and Long Frame Sync Pulses

19.6.3 Audio Control Data

Figure 70. Audio Slot with Audio Control Data

19.6.4 IOM-2 Mode

this IOM-2 mode, the AAI can only operate as a slave, i.e. IOM-2 channel 0, but ignores the other two IOM-2 channels. Figure 71 shows the structure of an IOM-2 Frame. Figure 71. IOM-2 Frame Structure (IO Expansion) for controlling the ISDN controller. Figure 72. CP3BT23/ISDN Controller Connections ! The AAI must be in IOM-2 Mode (AGCR.IOM2 = 1). (ACGR.IEFS = 1, ACGR.IEBC = 1). ! The internal frame rate must be 8 ksps (ACCR = 00BE).

19.6.5 Loopback Mode

ample during Built-In-Self-Test (BIST).

www.national.com 134 CP3BT23

19.6.6 Freeze Mode

The audio interface provides a FREEZE input, which allows to freeze the status of the audio interface while a develop- ment system examines the contents of the FIFOs and reg- isters. When the FREEZE input is asserted, the audio interface be- haves as follows: ! The receive FIFO or receive DMA registers are not up- dated with new data. ! The receive status bits (RXO, RXE, RXF , and RXAF) are not changed, even though the receive FIFO or receive DMA registers are read. ! The transmit shift register (ATSR) is not updated with new data from the transmit FIFO or transmit DMA regis- ters. ! The transmit status bits (TXU, TXF , TXE, and TXAE) are not changed, even though the transmit FIFO or transmit DMA registers are written. The time at which these registers are frozen will vary be- cause they operate from a different clock than the one used to generate the freeze signal.

19.7 AUDIO INTERFACE REGISTERS

Table 60 Audio Interface Registers Name Address Description ARFR FF FD40h Audio Receive FIFO Register ARDR0 FF FD42h Audio Receive DMA Register 0 ARDR1FF FD44h Audio Receive DMA Register 1 ARDR2 FF FD46h Audio Receive DMA Register 2 ARDR3 FF FD48h Audio Receive DMA Register 3 ATFR FF FD4Ah Audio Transmit FIFO Register ATDR0 FF FD4Ch Audio Transmit DMA Register 0 ATDR1FF FD4Eh Audio Transmit DMA Register 1 ATDR2 FF FD50h Audio Transmit DMA Register 2 ATDR3 FF FD52h Audio Transmit DMA Register 3 AGCR FF FD54h Audio Global Configuration Register AISCR FF FD56h Audio Interrupt Status and Control Register ARSCR FF FD58h Audio Receive Status and Control Register A TSCR FF FD5Ah Audio T ransmit Status and Control Register ACCR FF FD5Ch Audio Clock Control Register ADMACR FF FD5Eh Audio DMA Control Register Obsolete

135 www.national.com CP3BT23

19.7.1 Audio Receive FIFO Register (ARFR)

The Audio Receive FIFO register shows the receive FIFO location currently addressed by the Receive FIFO Read Pointer (RRP). The receive FIFO receives 8-bit or 16-bit data from the Audio Receive Shift Register (ARSR), when the ARSR is full. In 8-bit mode, only the lower byte of the ARFR is used, and the upper byte contains undefined data. In 16-bit mode, a 16-bit word is copied from ARSR into the receive FIFO. The CPU bus master has read-only access to the receive FIFO, represented by the ARFR register. After reset, the receive FIFO (ARFR) contains undefined data. ARFL The Audio Receive FIFO Low Byte shows the lower byte of the receive FIFO location cur- rently addressed by the Receive FIFO Read Pointer (RRP). ARFH The Audio Receive FIFO High Byte shows the upper byte of the receive FIFO location cur- rently addressed by the Receive FIFO Read Pointer (RRP). In 8-bit mode, ARFH contains undefined data.

19.7.2 Audio Receive DMA Register n (ARDRn)

The ARDRn register contains the data received within slot n, assigned for DMA support. In 8-bit mode, only the lower 8-bit portion of the ARDRn register is used, and the upper byte contains undefined data. In 16-bit mode, a 16-bit word is transferred from the Audio Receive Shift Register (ARSR) into the ARDRn register. The CPU bus master, typically a DMA controller, has read-only access to the receive DMA registers. After reset, these registers are clear. ARDL The Audio Receive DMA Low Byte field re- ceives the lower byte of the audio data copied from the ARSR. ARDH In 16-bit mode, the Audio Receive DMA High Byte field receives the upper byte of the audio data word copied from ARSR. In 8-bit mode, the ARDH register holds undefined data.

19.7.3 Audio Transmit FIFO Register (ATFR)

The ATFR register shows the transmit FIFO location cur- rently addressed by the Transmit FIFO Write Pointer (TWP). The Audio Transmit Shift Register (ATSR) receives 8-bit or 16-bit data from the transmit FIFO, when the ATSR is empty. In 8-bit mode, only the lower 8-bit portion of the ATSR is used, and the upper byte is ignored (not transferred into the ATSR). In 16-bit mode, a 16-bit word is copied from the t r a n s m i t F I F O i n t o t h e A T S R . T h e C P U b u s m a s t e r h a s write-only access to the transmit FIFO, represented by the ATFR register. After reset, the transmit FIFO (ATFR) con- tains undefined data. ATFL The Audio Transmit Low Byte field represents the lower byte of the transmit FIFO location currently addressed by the Transmit FIFO Write Pointer (TWP). ATFH In 16-bit mode, the Audio T ransmit FIFO High Byte field represents the upper byte of the transmit FIFO location currently addressed by the Transmit FIFO Write Pointer (TWP). In 8- bit mode, the ATFH field is not used.

19.7.4 Audio Transmit DMA Register n (ATDRn)

The ATDRn register contains the data to be transmitted in slot n, assigned for DMA support. In 8-bit mode, only the lower 8-bit portion of the ATDRn register is used, and the upper byte is ignored (not transferred into the ATSR). In 16- bit mode, the whole 16-bit word is transferred into the ATSR. The CPU bus master, typically a DMA controller, has write- only access to the transmit DMA registers. After reset, these registers are clear. ATDL The Audio T ransmit DMA Low Byte field holds the lower byte of the audio data. ATDH In 16-bit mode, the Audio T ransmit DMA High Byte field holds the upper byte of the audio data word. In 8-bit mode, the ATDH field is ig- nored. 7 0 ARFL 15 8 ARFH 7 0 ARDL 15 8 ARDH 7 0 ATFL 15 8 ATFH 7 0 ATDL 15 8 ATDH Obsolete

www.national.com 136 CP3BT23

19.7.5 Audio Global Configuration Register (AGCR)

The AGCR register controls the basic operation of the inter- face. The CPU bus master has read/write access to the AGCR register. After reset, this register is clear. ASS The Asynchronous/Synchronous Mode Se- lect bit controls whether the audio interface operates in Asynchronous or in Synchronous mode. After reset the ASS bit is clear, so the Synchronous mode is selected by default. 0 – Synchronous mode. 1 – Asynchronous mode. DWL The Data Word Length bit controls whether the transferred data word has a length of 8 or 16 bits. After reset, the DWL bit is clear, so 8- bit data words are used by default. 0 – 8-bit data word length. 1 – 16-bit data word length. LPB The Loop Back bit enables the loop back mode. In this mode, the SRD and STD pins are internally connected. After reset the LPB bit is clear, so by default the loop back mode is disabled. 0 – Loop back mode disabled. 1 – Loop back mode enabled. SCS The Slot Count Select field specifies the num- ber of slots within each frame. If the number of slots per frame is equal to 1, the audio inter- face operates in normal mode. If the number of slots per frame is greater than 1, the inter- face operates in network mode. After reset all SCS bits are cleared, so by default the audio interface operates in normal mode. IEFS The Internal/External Frame Sync bit controls, whether the frame sync signal for the receiver and transmitter are generated internally or provided from an external source. After reset, the IEFS bit is clear, so the frame synchroni- zation signals are generated internally by de- fault. 0 – Internal frame synchronization signal. 1 – External frame synchronization signal. FSS The F rame Sync Select bit controls whether the interface (receiver and transmitter) uses long or short frame synchronization signals. After reset the FSS bit is clear, so short frame synchronization signals are used by default. 0 – Short (bit length) frame synchronization signal. 1 – Long (word length) frame synchronization signal. IEBC The Internal/External Bit Clock bit controls whether the bit clocks for receiver and trans- mitter are generated internally or provided from an external source. After reset, the IEBC bit is clear, so the bit clocks are generated in- ternally by default. 0 – Internal bit clock. 1 – External bit clock. CRF The Clear Receive FIFO bit is used to clear the receive FIFO. When this bit is written with a 1, all pointers of the receive FIFO are set to their reset state. After updating the pointers, the CRF bit will automatically be cleared again. 0 – Writing 0 has no effect. 1 – Writing 1 clears the receive FIFO. CTF The Clear Transmit FIFO bit is used to clear the transmit FIFO. When this bit is written with a 1, all pointers of the transmit FIFO are set to their reset state. After updating the pointers, the CTF bit will automatically be cleared again. 0 – Writing 0 has no effect. 1 – Writing 1 clears the transmit FIFO. F S L T h e F r a m e S y n c L e n g t h f i e l d s p e c i f i e s t h e length of the frame synchronization signal, when a long frame sync signal (FSS = 1) and a 16-bit data word length (DWL = 1) are used. If an 8-bit data word length is used, long frame syncs are always 6 bit clocks in length. IFS The Inverted Frame Sync bit controls the po- larity of the frame sync signal. 0 – Active-high frame sync signal. 1 – Active-low frame sync signal. 7 6 5 4 3 2 1 0 IEBC FSS IEFS SCS LPB DWL ASS 15 14 13 12 11 10 9 8 CLKEN AAIEN IOM2 IFS FSL CTF CRF SCS Number of Slots per Frame Mode 00 1Normal mode

012 Network mode

137 www.national.com CP3BT23 IOM2 The IOM-2 Mode bit selects the normal PCM interface mode or a special IOM-2 mode used to connect to external ISDN controller devic- es. The AAI can only operate as a slave in the IOM-2 mode, i.e. the bit clock and frame sync signals are provided by the ISDN controller. If the IOM2 bit is clear, the AAI operates in the normal PCM interface mode used to connect to external PCM codecs and other PCM audio devices. 0 – IOM-2 mode disabled. 1 – IOM-2 mode enabled. AAIEN The AAI Enable bit controls whether the Ad- vanced Audio Interface is enabled. All AAI registers provide read/write access while (CLKEN = 1) AAIEN is clear. The AAIEN bit is clear after reset. 0 – AAI module disabled. 1 – AAI module enabled. CLKEN The Clock Enable bit controls whether the Ad- vanced Audio Interface clock is enabled. The CLKEN bit must be set to allow access to any AAI register. It must also be set before any other bit of the AGCR can be set. The CLKEN bit is clear after reset. 0 – AAI module clock disabled. 1 – AAI module clock enabled.

19.7.6 Audio Interrupt Status and Control Register

(AISCR) The ASCR register is used to specify the source and the conditions, when the audio interface interrupt is asserted to the Interrupt Control Unit. It also holds the interrupt pending bits and the corresponding interrupt clear bits for each audio interface interrupt source. The CPU bus master has read/ write access to the ASCR register. After reset, this register is clear. RXIE The Receive Interrupt Enable bit controls whether receive interrupts are generated. If the RXIE bit is clear, no receive interrupt will be generated. 0 – Receive interrupt disabled. 1 – Receive interrupt enabled. R X E I E T h e R e c e i v e E r r o r I n t e r r u p t E n a b l e b i t c o n - trols whether receive error interrupts are gen- erated. Setting this bit enables a receive error interrupt, when the Receive Buffer Overrun (RXOR) bit is set. If the RXEIE bit is clear, no receive error interrupt will be generated. 0 – Receive error interrupt disabled. 1 – Receive error interrupt enabled. TXIE The Transmit Interrupt Enable bit controls whether transmit interrupts are generated. Setting this bit enables a transmit interrupt, when the Transmit Buffer Almost Empty (TX- AE) bit is set. If the TXIE bit is clear, no inter- rupt will be generated. 0 – Transmit interrupt disabled. 1 – Transmit interrupt enabled. TXEIE The Transmit Error Interrupt Enable bit con- trols whether transmit error interrupts are gen- erated. Setting this bit to 1 enables a transmit error interrupt, when the Transmit Buffer Un- derrun (TXUR) bit is set. If the TXEIE bit is clear, no transmit error interrupt will be gener- ated. 0 – Transmit error interrupt disabled. 1 – Transmit error interrupt enabled. RXIP The Receive Interrupt Pending bit indicates that a receive interrupt is currently pending. The RXIP bit is cleared by writing a 1 to the RXIC bit. The RXIP bit provides read-only ac- cess. 0 – No receive interrupt pending. 1 – Receive interrupt pending. RXEIP The Receive Error Interrupt Pending bit indi- cates that a receive error interrupt is currently pending. The RXEIP bit is cleared by writing a 1 to the RXEIC bit. The RXEIP bit provides read-only access. 0 – No receive error interrupt pending. 1 – Receive error interrupt pending. TXIP The T ransmit Interrupt Pending bit indicates that a transmit interrupt is currently pending. The TXIP bit is cleared by writing a 1 to the TXIC bit. The TXIP bit provides read-only ac- cess. 0 – No transmit interrupt pending. 1 – Transmit interrupt pending. TXEIP Transmit Error Interrupt Pending. This bit indi- cates that a transmit error interrupt is currently pending. The TXEIP bit is cleared by software by writing a 1 to the TXEIC bit. The TXEIP bit provides read-only access. 0 – No transmit error interrupt pending. 1 – Transmit error interrupt pending. RXIC The Receive Interrupt Clear bit is used to clear the RXIP bit. 0 – Writing a 0 to the RXIC bit is ignored. 1 – Writing a 1 clears the RXIP bit. RXEIC The Receive Error Interrupt Clear bit is used to clear the RXEIP bit. 0 – Writing a 0 to the RXEIC bit is ignored. 1 – Writing a 1 clears the RXEIP bit. TXIC The Transmit Interrupt Clear bit is used to clear the TXIP bit. 0 – Writing a 0 to the TXIC bit is ignored. 1 – Writing a 1 clears the TXIP bit. TXEIC The Transmit Error Interrupt Clear bit is used to clear the TXEIP bit. 0 – Writing a 0 to the TXEIC bit is ignored. 1 – Writing a 1 clears the TXEIP bit. 7 6 5 4 3 2 1 0 TXEIP TXIP RXEIP RXIP TXEIE TXIE RXEIE RXIE 15 12 11 10 9 8 Reserved TXEIC TXIC RXEIC RXIC Obsolete

www.national.com 138 CP3BT23

19.7.7 Audio Receive Status and Control Register

(ARSCR) The ARSCR register is used to control the operation of the receiver path of the audio interface. It also holds bits which report the current status of the receive FIFO. The CPU bus master has read/write access to the ASCR register. At re- set, this register is loaded with 0004h. RXAF The Receive Buffer Almost Full bit is set when the number of data bytes/words in the receive buffer is equal to the specified warning limit. 0 – Receive FIFO below warning limit. 1 – Receive FIFO is almost full. RXF The Receive Buffer Full bit is set when the re- ceive buffer is full. The RXF bit is set when the RWP is equal to the RRP and the last access was a write to the FIFO. 0 – Receive FIFO is not full. 1 – Receive FIFO full. RXE The Receive Buffer Empty bit is set when the the RRP is equal to the RWP and the last ac- cess to the FIFO was a read operation (read from ARDR). 0 – Receive FIFO is not empty. 1 – Receive FIFO is empty. RXO The Receive Overflow bit indicates that a re- ceive shift register has overrun. This occurs, when a completed data word has been shifted into ARSR, while the receive FIFO was al- ready full (the RXF bit was set). In this case, the new data in ARSR will not be copied into the FIFO and the RWP will not be increment- ed. Also, no receive interrupt and DMA re- quest will generated (even if enabled). 0 – No overflow has occurred. 1 – Overflow has occurred. RXSA The Receive Slot Assignment field specifies which slots are recognized by the receiver of the audio interface. Multiple slots may be en- abled. If the frame consists of less than 4 slots, the RXSA bits for unused slots are ig- nored. For example, if a frame only consists of 2 slots, RXSA bits 2 and 3 are ignored. The following table shows the slot assignment scheme. After reset the RXSA field is clear, so software must load the correct slot assignment. RXDSA The Receive DMA Slot Assignment field spec- ifies which slots (audio channels) are support- ed by DMA. If the RXDSA bit is set for an assigned slot n (RXSAn = 1), the data re- ceived within this slot will not be transferred into the receive FIFO, but will instead be writ- ten into the corresponding Receive DMA data register (ARDRn). A DMA request n is assert- ed, when the ARDRn is full and if the RMA bit n is set. If the RXSD bit for a slot is clear, the RXDSA bit is ignored. The following table shows the DMA slot assignment scheme. RXFWL The Receive FIFO Warning Level field speci- fies when a receive interrupt is asserted. A re- ceive interrupt is asserted, when the number of bytes/words in the receive FIFO is greater than the warning level value. An RXFWL value of 0 means that a receive interrupt is asserted if one or more bytes/words are in the RX FIFO. After reset, the RXFWL bit is clear. 7 4 3 2 1 0 RXSA RXO RXE RXF RXAF 15 12 11 8 RXFWL RXDSA RXSA Bit Slots Enabled RXSA0 0 RXSA11 RXSA2 2 RXSA3 3 RXDSA Bit Slots Enabled for DMA RXDSA0 0 RXDSA11 RXDSA2 2 RXDSA3 3 Obsolete

139 www.national.com CP3BT23

19.7.8 Audio Transmit Status and Control Register

(ATSCR) The ASCR register controls the basic operation of the inter- face. It also holds bits which report the current status of the audio communication. The CPU bus master has read/write access to the ASCR register. At reset, this register is loaded with F003h. T X A E T h e T r a n s m i t F I F O A l m o s t E m p t y b i t i s s e t when the number of data bytes/words in transmit buffer is equal to the specified warn- ing limit. 0 – Transmit FIFO above warning limit. 1 – Transmit FIFO at or below warning limit. TXE The T ransmit FIFO Empty bit is set when the transmit buffer is empty. The TXE bit is set to one every time the TRP is equal to the TWP and the last access to the FIFO was read op- eration (into ATSR). 0 – Transmit FIFO not empty. 1 – Transmit FIFO empty. TXF The Transmit FIFO Full bit is set when the TWP is equal to the TRP and the last access to the FIFO was write operation (write to A T- DR). 0 – Transmit FIFO not full. 1 – Transmit FIFO full. TXU The Transmit Underflow bit indicates that the transmit shift register (ATSR) has underrun. This occurs when the transmit FIFO was al- ready empty and a complete data word has been transferred. In this case, the TRP will be decremented by 1 and the previous data will be retransmitted. No transmit interrupt and no DMA request will be generated (even if en- abled). 0 – Transmit underrun occurred. 1 – Transmit underrun did not occur. TXSA The Transmit Slot Assignment field specifies during which slots the transmitter is active and drives data through the STD pin. The STD pin is in high impedance state during all other slots. If the frame consists of less than 4 slots, the TXSA bits for unused slots are ignored. For example, if a frame only consists of 2 slots, TXSA bits 2 and 3 are ignored. The fol- lowing table shows the slot assignment scheme. After reset, the TXSA field is clear, so soft- ware must load the correct slot assignment. TXDSA The Transmit DMA Slot Assignment field specifies which slots (audio channels) are supported by DMA. If the TXDSA bit is set for an assigned slot n (TXSAn = 1), the data to be transmitted within this slot will not be read from the transmit FIFO, but will instead be read from the corresponding Transmit DMA data register (ATDRn). A DMA request n is as- serted when the ATDRn is empty. If the TSA bit for a slot is clear, the TXDSA bit is ignored. The following table shows the DMA slot as- signment scheme. TFWL The Transmit FIFO Warning Level field speci- fies when a transmit interrupt is asserted. A transmit interrupt is asserted when the num- ber of bytes or words in the transmit FIFO is equal or less than the warning level value. A TXFWL value of Fh means that a transmit in- terrupt is asserted if one or more bytes or words are available in the transmit FIFO. At reset, the TXFWL field is loaded with Fh. 7 4 3 2 1 0 TXSA TXU TXF TXE TXAE 15 12 11 8 TXFWL TXDSA TXSA Bit Slots Enabled TXSA0 0 TXSA11 TXSA2 2 TXSA3 3 TXDSA Bit Slots Enabled for DMA TXDSA0 0 TXDSA11 TXDSA2 2 TXDSA3 3 Obsolete

www.national.com 140 CP3BT23

19.7.9 Audio Clock Control Register (ACCR)

The ACCR register is used to control the bit timing of the au- dio interface. After reset, this register is clear. CSS The Clock Source Select bit selects one out of two possible clock sources for the audio inter- face. After reset, the CSS bit is clear. 0 – The Auxiliary Clock 1 is used to clock the Audio Interface. 1 – The 48-MHz clock is used to clock the Au- dio Interface. FCPRS The Frame Clock Prescaler is used to divide the bit clock to generate the frame clock for the receive and transmit operations. The bit clock is divided by (FCPRS + 1). After reset, the FCPRS field is clear. The maximum al- lowed bit clock rate to achieve an 8 kHz frame clock is 1024 kHz. This value must be set cor- rectly even if the frame sync is generated ex- ternally. BCPRS The Bit Clock Prescaler is used to divide the audio interface clock (selected by the CSS bit) to generate the bit cloc k f or the receiv e and transmit operations. The audio interface input clock is divided by (BCPRS + 1). After reset, the BCPRS[7:0] bits are clear.

19.7.10 Audio DMA Control Register (ADMACR)

The ADMACR register is used to control the DMA support of the audio interface. In addition, it is used to configure the automatic transmission of the audio control bits. After reset, this register is clear. RMD The Receive Master DMA field specify which slots (audio channels) are supported by DMA, i.e. when a DMA request is asserted to the DMA controller . If the RMDn bit is set f or an assigned slot n (RXDSAn = 1), a DMA request n is asserted, when the ARDRn is full. If the RXDSAn bit for a slot is clear, the RMDn bit is ignored. The following table shows the receive DMA request scheme. TMD The Transmit Master DMA field specifies which slots (audio channels) are supported by DMA, i.e. when a DMA request is asserted to the DMA controller. If the TMD bit is set for an assigned slot n (TXDSAn = 1), a DMA request n is asserted, when the A TDRn register is empty. If the TXDSA bit for a slot is clear, the TMD bit is ignored. The following table shows the transmit DMA request scheme. ACD The Audio Control Data field is used to fill the remaining bits of a 16-bit slot if only 13, 14, or 15 bits of PCM audio data are transmitted. ACO The Audio Control Output field controls the number of control bits appended to the PCM data word. 00 – No Audio Control bits are appended. 01 – Append ACD0. 10 – Append ACD1:0. 11 – Append ACD2:0. 7 1 0 FCPRS CSS 15 8 BCPRS 7 4 3 0 TMD RMD 15 131211 10 8 Reserved ACO ACD RMD DMA Request Condition

0000 None

0010 ARDR1 full

0011 ARDR0 full or ARDR1 full

0010 ATDR1 empty

0011 A TDR0 empty or

20.0 CVSD/PCM Conversion Module

gram of the CVSD to PCM module. Figure 73. CVSD/PCM Converter Block Diagram

20.1 OPERATION

2 MHz input clock based upon the System Clock (usually

either one of the CVSD FIFOs is almost empty or almost full. into an 8 kHz, 16-bit data stream.

20.2 PCM CONVERSIONS

aligned 14-bit linear data format with the two LSBs unused.

2 MHz

www.national.com 142 CP3BT23 If the module is only used for PCM conversions, the CVSD clock can be disabled by clearing the CVSD Clock Enable bit (CLKEN) in the control register.

20.3 CVSD CONVERSION

The CVSD/PCM converter module transforms either 8-bit logarithmic or 13- to 16-bit linear PCM samples at a fixed rate of 8 ksps. The CVSD to PCM conversion format must be specified by the CVSDCONV control bits in the CVSD Control register (CVCTRL). The CVSD algorithm is designed for 2’s complement 16-bit data and is tuned for best performance with typical voice da- ta. Mild distortion will occur for peak signals greater than -6 dB. The Bluetooth CVSD standard is designed for best per- formace with typical voice signals: nominaly -6dB with occa- sional peaks to 0dB rather than full-scale inputs. Distortion of signals greater than -6dB is not considered detrimental to subjective quality tests for voice-band applications and al- lows for greater clarity for signals below -6dB. The gain of the input device should be tuned with this in mind. If required, the RESOLUTION field of the CVCTRL register can be used to optimize the level of the 16-bit linear input data by providing attenuations (right-shifts with sign exten- tion) of 1, 2, or 3 bits. Log data is always 8 bit, but to perform the CVSD conver- sion, the log data is first converted to 16-bit 2’s complement linear data. A-law and u-law conversion can also slightly af- fect the optimum gain of the input data. The CVCTRL.RES- OLUTION field can be used to attenuate the data if required. If the resolution is not set properly, the audio signal may be clipped or have reduced attenuation.

20.4 PCM TO CVSD CONVERSION

The converter core reads out the double-buffered PCMIN register every 125 µs and writes a new 16-bit CVSD data stream into the CVSD Out FIFO every 250 µs. If the PCMIN buffer has not been updated with a new PCM sample be- tween two reads from the CVSD core, the old PCM data is used again to maintain a fixed conversion rate. Once a new 16-bit CVSD data stream has been calculated, it is copied into the 8 × 16-bit wide CVSD Out FIFO. If there are only three empty words (16-bit) left in the FIFO, the nearly full bit (CVNF) is set, and, if enabled (CVSDINT = 1), an interrupt request is asserted. If the CVSD Out FIFO is full, the full bit (CVF) is set, and, if enabled (CVSDERRINT = 1), an interrupt request is assert- ed. In this case, the CVSD Out FIFO remains unchanged. Within the interrupt handler, the CPU can read out the new CVSD data. If the CPU reads from an already empty CVSD Out FIFO, a lockup of the FIFO logic may occur which per- sists until the next reset. Software must check the CVOUTST field of the CVSTAT register to read the number of valid words in the FIFO. Software must not use the CVNF bit as an indication of the number of valid words in the FIFO.

20.5 CVSD TO PCM CONVERSION

The converter core reads from the CVSD In FIFO every 250 µs and writes a new PCM sample into the PCMOUT buffer every 125 µs. If the previous PCM data has not yet been transferred to the audio interface, it will be overwritten with the new PCM sample. If there are only three unread words left, the CVSD In Nearly Empty bit (CVNE) is set and, if enabled (CVSDINT = 1), an interrupt request is generated. If the CVSD In FIFO is empty, the CVSD In Empty bit (CVE) is set and, if enabled (CVSDERRINT = 1), an interrupt re- quest is generated. If the converter core reads from an al- ready empty CVSD In FIFO, the FIFO automatically returns a checkerboard pattern to guarantee a minimum level of dis- tortion of the audio stream.

20.6 INTERRUPT GENERATION

An interrupt is generated in any of the following cases: ! When a new PCM sample has been written into the PCMOUT register and the CVCTRL.PCMINT bit is set. ! When a new PCM sample has been read from the PCMIN register and the CVCTRL.PCMINT bit is set. ! When the CVSD In FIFO is nearly empty (CVSTAT.CVNE = 1) and the CVCTRL.CVSDINT bit is set. ! When the CVSD Out FIFO is nearly full (CVSTAT.CVNF = 1) and the CVCTRL.CVSDINT bit is set. ! When the CVSD In FIFO is empty (CVSTAT.CVE = 1) and the CVCTRL.CVSDERRINT bit is set. ! When the CVSD Out FIFO is full (CVSTAT.CVF = 1) and the CVCTRL.CVSDERRINT bit is set. B o t h t h e C V S D I n a n d C V S D O u t F I F O s h a v e a s i z e o f 8 × 16 bit (8 words). The warning limits for the two FIFOs is set at 5 words. (The CVSD In FIFO interrupt will occur when there are 3 words left in the FIFO, and the CVSD Out FIFO interrupt will occur when there are 3 or less empty words left in the FIFO.) The limit is set to 5 words because Bluetooth audio data is transferred in packages composed of 10 or multiples of 10 bytes.

20.7 DMA SUPPORT

The CVSD module can operate with any of four DMA chan- nels. Four DMA channels are required for processor inde- pendent operation. Both receive and transmit for CVSD data and PCM data can be enabled individually. The CVSD/ PCM module asserts a DMA request to the on-chip DMA controller under the following conditions: ! The DMAPO bit is set and the PCMOUT register is full, because it has been updated by the converter core with a new PCM sample. (The DMA controller can read out one PCM data word from the PCMOUT register.) ! The DMAPI bit is set and the PCMIN register is empty, because it has been read by the converter core. (The DMA controller can write one new PCM data word into the PCMIN register.) ! The DMACO bit is set and a new 16-bit CVSD data stream has been copied into the CVSD Out FIFO. (The DMA controller can read out one 16-bit CVSD data word from the CVSD Out FIFO.) ! The DMACI bit is set and a 16-bit CVSD data stream has been read from the CVSD In FIFO. (The DMA controller can write one new 16-bit CVSD data word into the CVSD In FIFO.) Obsolete

143 www.national.com CP3BT23 The CVSD/PCM module only supports indirect DMA trans- fers. Therefore, transferring PCM data between the CVSD/ PCM module and another on-chip module requires two bus cycles. The trigger for DMA may also trigger an interrupt if the cor- responding enable bits in the CVCTRL register is set. Therefore care must be taken when setting the desired in- terrupt and DMA enable bits. The following conditions must be avoided: ! Setting the PCMINT bit and either of the DMAPO or DMAPI bits. ! Setting the CVSDINT bit and either of the DMACO or DMACI bits.

20.8 FREEZE

The CVSD/PCM module provides support for an In-System- Emulator by means of a special FREEZE input. While FREEZE is asserted the module will exhibit the following be- havior: ! CVSD In FIFO will not have data removed by the con- verter core. ! CVSD Out FIFO will not have data added by the convert- er core. ! PCM Out buffer will not be updated by the converter core. ! The Clear-on-Read function of the following status bits in the CVST AT register is disabled: ! PCMINT ! CVE ! CVF

20.9 CVSD/PCM CONVERTER REGISTERS

Table 61 lists the CVSD/PCM registers.

20.9.1 CVSD Data Input Register (CVSDIN)

The CVSDIN register is a 16-bit wide, write-only register. It is used to write CVSD data into the CVSD to PCM converter FIFO. The FIFO is 8 words deep. The CVSDIN bit 15 repre- sents the CVSD data bit at t = t 0, CVSDIN bit 0 represents the CVSD data bit at t = t0 - 250 ms.

20.9.2 CVSD Data Output Register (CVSDOUT)

The CVSDOUT register is a 16-bit wide read-only register. It is used to read the CVSD data from the PCM to CVSD converter. The FIFO is 8 words deep. Reading the CVSD- OUT register after reset returns undefined data.

20.9.3 PCM Data Input Register (PCMIN)

The PCMIN register is a 16-bit wide write-only register. It is used to write PCM data to the PCM to CVSD converter via the peripheral bus. It is double-buffered, providing a 125 µs period for an interrupt or DMA request to respond.

20.9.4 PCM Data Output Register (PCMOUT)

The PCMOUT register is a 16-bit wide read-only register. It is used to read PCM data from the CVSD to PCM converter. It is double-buffered, providing a 125 µs period for an inter- rupt or DMA request to respond. After reset the PCMOUT register is clear. Table 61 CVSD/PCM Registers Name Address Description CVSDIN FF FC20h CVSD Data Input Register CVSDOUT FF FC22h CVSD Data Output Register PCMIN FF FC24h PCM Data Input Register PCMOUT FF FC26h PCM Data Output Register LOGIN FF FC28h Logarithmic PCM Data Input Register LOGOUT FF FC2Ah Logarithmic PCM Data Output Register LINEARIN FF FC2Ch Linear PCM Data Input Register LINEAROUT FF FC2Eh Linear PCM Data Output Register CVCTRL FF FC30h CVSD Control Regis- ter CVSTAT FF FC32h CVSD Status Register 15 0 CVSDIN 150 CVSDOUT 150 PCMIN 150 PCMOUT Table 61 CVSD/PCM Registers Name Address Description Obsolete

www.national.com 144 CP3BT23

20.9.5 Logarithmic PCM Data Input Register (LOGIN)

The LOGIN register is an 8-bit wide write-only register. It is used to receive 8-bit logarithmic PCM data from the periph- eral bus and convert it into 13-bit linear PCM data.

20.9.6 Logarithmic PCM Data Output Register

(LOGOUT) The LOGOUT register is an 8-bit wide read-only register. It holds logarithmic PCM data that has been converted from linear PCM data. After reset, the LOGOUT register is clear.

20.9.7 Linear PCM Data Input Register (LINEARIN)

The LINEARIN register is a 16-bit wide write-only register. The data is left-aligned. When converting to A-law, bits 2:0 are ignored. When converting to µ-law, bits 1:0 are ignored.

20.9.8 Linear PCM Data Output Register

(LINEAROUT) The LINEAROUT register is a 16-bit wide read-only register. The data is left-aligned. When converting from A-law, bits 2:0 are clear. When converting from µ-law, bits 1:0 are clear. After reset, this register is clear.

20.9.9 CVSD Control Register (CVCTRL)

The CVCTRL register is a 16-bit wide, read/write register that controls the mode of operation and of the module’s in- terrupts. At reset, all implemented bits are cleared. CVEN The Module Enable bit enables or disables the CVSD conversion module interface. When the bit is set, the interface is enabled which allows read and write operations to the rest of the module. When the bit is clear, the module is disabled. When the module is disabled the status register CVSTAT will be cleared to its reset state. 0 – CVSD module enabled. 1 – CVSD module disabled. CLKEN The CVSD Clock Enable bit enables the 2- MHz clock to the filter engine and CVSD en- coders and decoders. 0 – CVSD module clock disabled. 1 – CVSD module clock enabled. PCMINT The PCM Interrupt Enable bit controls gener- ation of the PCM interrupt . If set, this bit en- ables the PCM interrupt. If the PCMINT bit is clear, the PCM interrupt is disabled. After re- set, this bit is clear. 0 – PCM interrupt disabled. 1 – PCM interrupt enabled. CVSDINT The CVSD FIFO Interrupt Enable bit controls generation of the CVSD interrupt. If set, this bit enables the CVSD interrupt that occurs if t h e C V S D I n F I F O i s n e a r l y e m p t y o r t h e CVSD Out FIFO is nearly full. If the CVSDINT bit is clear, the CVSD nearly full/nearly empty interrupt is disabled. After reset, this bit is clear. 0 – CVSD interrupt disabled. 1 – CVSD interrupt enabled. CVSDERRINT The CVSD FIFO Error Interrupt Enable bit controls generation of the CVSD error inter- rupt. If set, this bit enables an interrupt to oc- c u r w h e n t h e C V S D O u t F I F O i s f u l l o r t h e CVSD In FIFO is empty. If the CVSDERROR- INT bit is clear, the CVSD full/empty interrupt is disabled. After reset, this bit is clear. 0 – CVSD error interrupt disabled. 1 – CVSD error interrupt enabled. DMACO The DMA Enable for CVSD Out bit enables hardware DMA control for reading CVSD data from the CVSD Out FIFO. If clear, DMA sup- port is disabled. After reset, this bit is clear. 0 – CVSD output DMA disabled. 1 – CVSD output DMA enabled. DMACI The DMA Enable for CVSD In bit enables hardware DMA control for writing CVSD data into the CVSD In FIFO. If clear, DMA support is disabled. After reset, this bit is clear. 0 – CVSD input DMA disabled. 1 – CVSD input DMA enabled. DMAPO The DMA Enable for PCM Out bit enables hardware DMA control for reading PCM data from the PCMOUT register. If clear, DMA sup- port is disabled. After reset, this bit is clear. 0 – PCM output DMA disabled. 1 – PCM output DMA enabled. LOGIN LOGOUT 15 0 LINEARIN 15 0 LINEAROUT 7 6 5 4 3 2 1 0 DMA PO DMA CI DMA CO CVSD ERR- INT CVSD INT PCM INT CLK EN CVEN 15 14 13 12 11 10 9 8 Res. RESOLUTION PCMCONV CVSDCONV DMAPI Obsolete

145 www.national.com CP3BT23 DMAPI The DMA Enable for PCM In bit enables hard- ware DMA control for writing PCM data into the PCMIN register. If cleared, DMA support is disabled. After reset, this bit is clear. 0 – PCM input DMA disabled. 1 – PCM input DMA enabled. CVSDCONV The CVSD to PCM Conversion Format field specifies the PCM format for CVSD/PCM con- versions. After reset, this field is clear. 00 – CVSD <-> 8-bit µ-Law PCM. 01 – CVSD <-> 8-bit A-Law PCM. 10 – CVSD <-> Linear PCM. 11 – Reserved. PCMCONV The PCM to PCM Conversion Format bit se- lects the PCM format for PCM/PCM conver- sions. 0 – Linear PCM <-> 8-bit µ-Law PCM 1 – Linear PCM <-> 8-bit A-Law PCM RESOLUTION The Linear PCM Resolution field specifies the attenuation of the PCM data for the linear PCM to CVSD conversions by right shifting and sign extending the data. This affects the log PCM data as well as the linear PCM data. The log data is converted to either left-justified zero-stuffed 13-bit (A-law) or 14-bit (u-law). The RESOLUTION field can be used to com- pensate for any change in average levels re- sulting from this conversion. After reset, these two bits are clear. 00 – No shift. 01 – 1-bit attentuation. 10 – 2-bit attentuation. 11 – 3-bit attentuation.

20.9.10 CVSD Status Register (CVSTAT)

The CVST AT register is a 16-bit wide, read-only register that holds the status information of the CVSD/PCM module. At reset, and if the CVCTL1.CVEN bit is clear, all implemented bits are cleared. CVNE The CVSD In FIFO Nearly Empty bit indicates when only three CVSD data words are left in the CVSD In FIFO, so new CVSD data should be written into the CVSD In FIFO. If the CVS- DINT bit is set, an interrupt will be asserted when the CVNE bit is set. If the DMACI bit is set, a DMA request will be asserted when this bit is set. The CVNE bit is cleared when the CVSTAT register is read. 0 – CVSD In FIFO is not nearly empty. 1 – CVSD In FIFO is nearly empty. CVNF The CVSD Out FIFO Nearly Full bit indicates when only three empty word locations are left i n t h e C V S D O u t F I F O , s o t h e C V S D O u t FIFO should be read. If the CVSDINT bit is set, an interrupt will be asserted when the CVNF bit is set. If the DMACO bit is set, a DMA request will be asserted when this bit is set. Software must not rely on the CVNF bit as an indicator of the number of valid words in the FIFO. Software must check the CVOUTST field to read the number of valid words in the FIFO. The CVNF bit is cleared when the CVSTAT register is read. 0 – CVSD Out FIFO is not nearly full. 1 – CVSD Out FIFO is nearly full. PCMINT The PCM Interrupt bit set indicates that the PCMOUT register is full and needs to be read or the PCMIN register is empty and needs to be loaded with new PCM data. The PCMINT bit is cleared when the CVSTAT register is read, unless the device is in FREEZE mode. 0 – PCM does not require service. 1 – PCM requires loading or unloading. CVE The CVSD In FIFO Empty bit indicates when t h e C V S D I n F I F O h a s b e e n r e a d b y t h e CVSD converter while the FIFO was already empty. If the CVSDERRORINT bit is set, an interrupt will be asserted when the CVE bit is set. The CVE bit is cleared when the CVSTAT register is read, unless the device is in FREEZE mode. 0 – CVSD In FIFO has not been read while empty. 1 – CVSD In FIFO has been read while emp- ty. C V F T h e C V S D O u t F I F O F u l l b i t s e t i n d i c a t e s whether the CVSD Out FIFO has been written by the CVSD converter while the FIFO was al- ready full. If the CVSDERRORINT bit is set, an interrupt will be asserted when the CVF bit is set. The CVF bit is cleared when the CVSTAT register is read, unless the device is in FREEZE mode. 0 – CVSD Out FIFO has not been written while full. 1 – CVSD Out FIFO has been written while full. CVINST The CVSD In FIFO Status field reports the current number of empty 16-bit word locations in the CVSD In FIFO. When the FIFO is emp- ty, the CVINST field will read as 111b. When the FIFO holds 7 or 8 words of data, the CVINST field will read as 000b. CVOUTST CVSD Out FIFO Status field reports the cur- rent number of valid 16-bit CVSD data words i n t h e C V S D O u t F I F O . W h e n t h e F I F O i s empty, the CVOUTST field will read as 000b. When the FIFO holds 7 or 8 words of data, the CVOUTST field will read as 111b. 7 5 4 3 2 1 0 CVINST CVF CVE PCMINT CVNF CVNE 15 11 10 8 Reserved CVOUTST Obsolete

www.national.com 146 CP3BT23

21.0 UART Modules

The CP3BT23 provides four UART modules. Each UART module is a full-duplex Universal Asynchronous Receiver/ Transmitter that supports a wide range of software-pro- grammable baud rates and data formats. It handles auto- matic parity generation and several error detection schemes. All UART modules offer the following features: ! Full-duplex double-buffered receiver/transmitter ! Asynchronous operation ! Programmable baud rate ! Programmable framing formats: 7, 8, or 9 data bits; even, odd, or no parity; one or two stop bits (mark or space) ! Hardware parity generation for data transmission and parity check for data reception ! Interrupts on “transmit ready” and “receive ready” condi- tions, separately enabled ! Software-controlled break transmission and detection ! Internal diagnostic capability ! Automatic detection of parity, framing, and overrun errors One module, UART0, offers the following additional fea- tures: ! Synchronous operation using the CKX external clock pin ! Hardware flow control (CTS and RTS signals) ! DMA capability

21.1 FUNCTIONAL OVERVIEW

Figure 74 is a block diagram of the UART module showing the basic functional units in the UART: ! Transmitter ! Receiver ! Baud Rate Generator ! Control and Error Detection The Transmitter block consists of an 8-bit transmit shift reg- ister and an 8-bit transmit buffer. Data bytes are loaded in parallel from the buffer into the shift register and then shifted out serially on the TXD pin. The Receiver block consists of an 8-bit receive shift register and an 8-bit receive buffer. Data is received serially on the RXD pin and shifted into the shift register. Once eight bits have been received, the contents of the shift register are transferred in parallel to the receive buffer. The Transmitter and Receiver blocks both contain exten- sions for 9-bit data transfers, as required by the 9-bit and loopback operating modes. The Baud Rate Generator generates the clock for the syn- chronous and asynchronous operating modes. It consists of two registers and a two-stage counter. The registers are used to specify a prescaler value and a baud rate divisor. The first stage of the counter divides the UART clock based on the value of the programmed prescaler to create a slower clock. The second stage of the counter creates the baud rate clock by dividing the output of the first stage based on the programmed baud rate divisor. The Control and Error Detection block contains the UART control registers, control logic, error detection circuit, parity generator/checker, and interrupt generation logic. The con- trol registers and control logic determine the data format, mode of operation, clock source, and type of parity used. The error detection circuit generates parity bits and checks for parity, framing, and overrun errors. The Flow Control Logic block provides the capability for hardware handshaking between the UART and a peripheral device. When the peripheral device needs to stop the flow of data from the UART, it de-asserts the clear-to-send (CTS signal which causes the UART to pause after sending the current frame (if any). The UART asserts the ready-to-send (RTS ) signal to the peripheral when it is ready to send a character.

21.2 UART OPERATION

The UART has two basic modes of operation: synchronous and asynchronous. Synchronous mode is only supported for the UART0 module. In addition, there are two special- purpose modes, called attention and diagnostic. This sec- tion describes the operating modes of the UART.

21.2.1 Asynchronous Mode

The asynchronous mode of the UART enables the device to communicate with other devices using just two communica- tion signals: transmit and receive. In asynchronous mode, the transmit shift register (TSFT) and the transmit buffer (UnTBUF) double-buffer the data for transmission. To transmit a character, a data byte is loaded in the UnTBUF register. The data is then transferred to the TSF T register . While t he TSFT register is shif ting out the current character (LSB first) on the TXD pin, the UnTBUF register is loaded by software with the next byte to be trans- mitted. When TSFT finishes transmission of the last stop bit of the current frame, the contents of UnTBUF are trans- ferred to the TSFT register and the Transmit Buffer Empty bit (UTBE) is set. The UTBE bit is automatically cleared by the UART when software loads a new character into the UnTBUF register. During transmission, the UXMIP bit is set high by the UART. This bit is reset only after the UART has sent the last stop bit of the current character and the UnT- BUF register is empty. The UnTBUF register is a read/write register. The TSFT register is not software accessible. In asynchronous mode, the input frequency to the UART is 16 times the baud rate. In other words, there are 16 clock cycles per bit time. In asynchronous mode, the baud rate generator is always the UART clock source. The receive shift register (RSFT) and the receive buffer (Un- RBUF) double buffer the data being received. The UART re- ceiver continuously monitors the signal on the RXD pin for a low level to detect the beginning of a start bit. On sensing this low level, the UART waits for seven input clock cycles and samples again three times. If all three samples still in- dicate a valid low, then the receiver considers this to be a valid start bit, and the remaining bits in the character frame are each sampled three times, around the mid-bit position. For any bit following the start bit, the logic value is found by majority voting, i.e. the two samples with the same value de- fine the value of the data bit. Figure 75 illustrates the pro- cess of start bit detection and bit sampling. Obsolete

21.2.2 Synchronous Mode

are transferred synchronously with the UART clock signal. Figure 76. Data bytes are transmitted and received least significant bit (LSB) first. Figure 76. UART Synchronous Communication current character, LSB first, on each rising edge of the clock. character and the UnTBUF register is empty. on the CKX pin as an output.

21.2.3 Attention Mode

next address character (by setting the UATN bit again). received is read from URB9 in the UART Status Register.

21.2.4 Diagnostic Mode

number of start and stop bits is programmable.

21.2.5 Frame Format Selection

is generated and transmitted following the seven data bits. Figure 77. 7-Bit Data Frame Options

1 Start

Figure 78. 8-Bit Data Frame Options all eight bits of UnTBUF and UnRBUF are used for data. generated or verified in this mode. Figure 79. 9-bit Data Frame Options

21.2.6 Baud Rate Generator

caler (UnPSC) and an 11-bit baud rate divisor (UnDIV). SC) setting and the prescaler factors is shown in Table 62. U A R T c l o c k i s t u r n e d o f f t o r e d u c e p o w e r c o n s u m p t i o n .

21.2.7 Interrupts

00000 No clock

2 Start

3 Start

Figure 80. UART Interrupts bits in the UnICTRL register. the UnTBUF register (which clears the UTBE bit). (which clears the URBF bit). can be programmed to generate edge-triggered interrupts.

21.2.8 DMA Support

DMA can be enabled simultaneously.

21.2.9 Break Generation and Detection

or longer after a missing stop bit is detected.

21.2.10 Parity Generation and Detection

abled and disabled using the PEN bit in the UnFRS register.

151 www.national.com CP3BT23

21.3 UART REGISTERS

Software interacts with the UART modules by accessing the UART registers, as listed in T able 63. Table 63 UART Registers Name Address Description U0RBUF FF F202h UART0 Receive Data Buffer U0TBUF FF F200h UART0 Transmit Data Buffer U0PSR FF F20Eh UART0 Baud Rate Prescaler U0BAUD FF F20Ch UART0 Baud Rate Divisor U0FRS FF F208h UART0 Frame Select Register U0MDSL1FF F20Ah UART0 Mode Select Register 1 U0STAT FF F206h UART0 Status Register U0ICTRL FF F204h UART0 Interrupt Con- trol Register U0OVR FF F210h UART0 Oversample Rate Register U0MDSL2 FF F212h UART0 Mode Select Register 2 U0SPOS FF F214h UART0 Sample Position Register U1RBUF FF F222h UART1 Receive Data Buffer U1TBUF FF F220h UART1 T ransmit Data Buffer U1PSR FF F22Eh UART1 Baud Rate Prescaler U1BAUD FF F22Ch UART1 Baud Rate Divisor U1FRS FF F228h UART1 Frame Select Register U1MDSL1 FF F22Ah UART1 Mode Select Register 1 U1STAT FF F226h UART1 Status Register U1ICTRL FF F224h UART1 Interrupt Con- trol Register U1OVR FF F230h UART1 Oversample Rate Register U1MDSL2 FF F232h UART1 Mode Select Register 2 U1SPOS FF F234h UART1 Sample Position Register U2RBUF FF F242h UART2 Receive Data Buffer U2TBUF FF F240h UART2 Transmit Data Buffer U2PSR FF F24Eh UART2 Baud Rate Prescaler U2BAUD FF F24Ch UART2 Baud Rate Divisor U2FRS FF F248h UART2 Frame Select Register U2MDSL1FF F24Ah UART2 Mode Select Register 1 U2STAT FF F246h UART2 Status Register U2ICTRL FF F244h UART2 Interrupt Con- trol Register U2OVR FF F250h UART2 Oversample Rate Register U2MDSL2 FF F252h UART2 Mode Select Register 2 U2SPOS FF F254h UART2 Sample Position Register U3RBUF FF F262h UART3 Receive Data Buffer U3TBUF FF F260h UART3 Transmit Data Buffer U3PSR FF F26Eh UART3 Baud Rate Prescaler U3BAUD FF F26Ch UART3 Baud Rate Divisor U3FRS FF F268h UART3 Frame Select Register U3MDSL1FF F26Ah UART3 Mode Select Register 1 U3STAT FF F266h UART3 Status Register U3ICTRL FF F264h UART3 Interrupt Con- trol Register Table 63 UART Registers Name Address Description Obsolete

www.national.com 152 CP3BT23

21.3.1 UART Receive Data Buffer (UnRBUF)

The UnRBUF register is a byte-wide, read/write register used to receive each data byte.

21.3.2 UART Transmit Data Buffer (UnTBUF)

The UnTBUF register is a byte-wide, read/write register used to transmit each data byte.

21.3.3 UART Baud Rate Prescaler (UnPSR)

The UnPSR register is a byte-wide, read/write register that contains the 5-bit clock prescaler and the upper three bits of the baud rate divisor. This register is cleared upon reset. The register format is shown below. UPSC The Prescaler field specifies the prescaler val- ue used for dividing the System Clock in the first stage of the two-stage divider chain. For the prescaler factors corresponding to each 5- bit value, see Table 62. U D I V 10: 8 T h e B au d R at e D iv iso r f ie ld h old s t h e t hr e e most significant bits (bits 10, 9, and 8) of the UART baud rate divisor used in the second stage of the two-stage divider chain. The re- maining bits of the baud rate divisor are held in the UnBAUD register.

21.3.4 UART Baud Rate Divisor (UnBAUD)

The UnBAUD register is a byte-wide, read/write register that contains the lower eight bits of the baud rate divisor. The register contents are unknown at power-up and are left un- changed by a reset operation. The register format is shown below. UDIV7:0 The Baud Rate Divisor field holds the eight lowest-order bits of the UART baud rate divi- sor used in the second stage of the two-stage divider chain. The three most significant bits are held in the UnPSR register. The divisor value used is (UDIV[10:0] + 1).

21.3.5 UART Frame Select Register (UnFRS)

The UnFRS register is a byte-wide, read/write register that controls the frame format, including the number of data bits, number of stop bits, and parity type. This register is cleared upon reset. The register format is shown below. UCHAR The Character Frame Format field selects the number of data bits per frame, not including the parity bit, as follows: 00 – 8 data bits per frame. 01 – 7 data bits per frame. 10 – 9 data bits per frame. 11 – Loop-back mode, 9 data bits per frame. USTP The Stop Bits bit specifies the number of stop bits transmitted in each frame. If this bit is 0, one stop bit is transmitted. If this bit is 1, two stop bits are transmitted. 0 – One stop bit per frame. 1 – Two stop bits per frame. UXB9 The Transmit 9th Data Bit holds the value of the ninth data bit, either 0 or 1, transmitted when the UART is configured to transmit nine data bits per frame. It has no effect when the UART is configured to transmit seven or eight data bits per frame. UPSEL The Parity Select field selects the treatment of the parity bit. When the UART is configured to transmit nine data bits per frame, the parity bit is omitted and the UPSEL field is ignored. 00 – Odd parity. 01 – Even parity. 10 – No parity, transmit 1 (mark). 11 – No parity, transmit 0 (space). U3OVR FF F270h UART3 Oversample Rate Register U3MDSL2 FF F272h UART3 Mode Select Register 2 U3SPOS FF F274h UART3 Sample Position Register 7 0 URBUF 7 0 UnTBUF 7 3 2 0 UPSC UDIV10:8 Table 63 UART Registers Name Address Description 7 0 UDIV7:0 7 6 5 4 3 2 1 0 Reserved UPEN UPSEL UXB9 USTP UCHAR Obsolete

153 www.national.com CP3BT23 UPEN The Parity Enable bit enables or disables par- ity generation and parity checking. When the UART is configured to transmit nine data bits per frame, there is no parity bit and the Un- PEN bit is ignored. 0 – Parity generation and checking disabled. 1 – Parity generation and checking enabled.

21.3.6 UART Mode Select Register 1 (UnMDSL1)

The UnMDSL1 register is a byte-wide, read/write register that selects the clock source, synchronization mode, atten- tion mode, and line break generation. This register is cleared at reset. The register format is shown below. UMOD The Mode bit selects between synchronous and asynchronous mode. Synchronous mode is only available for the UART0 module. 0 – Asynchronous mode. 1 – Synchronous mode. UATN The Attention Mode bit is used to enable At- tention mode. When set, this bit selects the at- tention mode of operation for the UART . When clear, the attention mode is disabled. The hardware clears this bit after an address frame is received. An address frame is a 9-bit character with a 1 in the ninth bit position. 0 – Attention mode disabled. 1 – Attention mode enabled. UBRK The Force Transmission Break bit is used to force the TXD output low. Setting this bit to 1 causes the TXD pin to go low. TXD remains low until the UBRK bit is cleared by software. 0 – Normal operation. 1 – TXD pin forced low. UCKS The Synchronous Clock Source bit controls the clock source when the UART operates in the synchronous mode (UMOD = 1). This functionality is only available for the UART0 module. If the UCKS bit is set, the UART op- erates from an external clock provided on the CKX pin. If the UCKS bit is clear, the UART operates from the baud rate clock produced b y the U A R T on the CKX pin. This bit is ig- nored when the UART operates in the asyn- chronous mode. 0 – Internal baud rate clock is used. 1 – External clock is used. UETD The Enable Transmit DMA bit controls wheth- er DMA is used for UART transmit operations. Enabling transmit DMA automatically disables transmit interrupts, without regard to the state of the UETI bit. 0 – Transmit DMA disabled. 1 – Transmit DMA enabled. UERD The Enable Receive DMA bit controls whether DMA is used for UART receive operations. Enabling receive DMA automatically disables receive interrupts, without regard to the state of the UERI bit. Receive error interrupts are unaffected by the UERD bit. 0 – Receive DMA disabled. 1 – Receive DMA enabled. UFCE The Flow Control Enable bit controls whether flow control interrupts are enabled. 0 – Flow control interrupts disabled. 1 – Flow control interrupts enabled. URTS The Ready To Send bit directly controls the state of the RTS output. 0 – RTS output is high. 1 – RTS output is low.

21.3.7 UART Status Register (UnSTAT)

The UnSTAT register is a byte-wide, read-only register that contains the receive and transmit status bits. This register is cleared upon reset. Any attempt by software to write to this register is ignored. The register format is shown below. UPE The Parity Error bit indicates whether a parity error is detected within a received character. This bit is automatically cleared by the hard- ware when the UnSTAT register is read. 0 – No parity error occurred. 1 – Parity error occurred. UFE The Framing Error bit indicates whether the UART fails to receive a valid stop bit at the end of a frame. This bit is automatically cleared by the hardware when the UnSTAT register is read. 0 – No framing error occurred. 1 – Framing error occurred. UDOE The Data Overrun Error bit is set when a new character is received and transferred to the UnRBUF register before software has read the previous character from the UnRBUF reg- ister. This bit is automatically cleared by the hardware when the UnSTAT register is read. 0 – No receive overrun error occurred. 1 – Receive overrun error occurred. UERR The Error Status bit indicates when a parity, framing, or overrun error occurs (any time that the UPE, UFE, or UDOE bit is set). It is auto- matically cleared by the hardware when the UPE, UFE, and UDOE bits are all 0. 0 – No receive error occurred. 1 – Receive error occurred. 7 6 5 4 3 2 1 0 URTS UFCE UERD UETD UCKS UBRK UATN UMOD 7 6 5 4 3 2 1 0 Res. UXMIP URB9 UBKD UERR UDOE UFE UPE Obsolete

www.national.com 154 CP3BT23 UBKD The Break Detect bit indicates when a line break condition occurs. This condition is de- tected if RXD remains low for at least ten bit times after a missing stop bit has been detect- ed at the end of a frame. The hardware auto- matically clears the UBKD bit on reading the UnSTAT register, but only if the break condi- tion on RXD no longer exists. If reading the UnSTAT register does not clear the UBKD bit because the break is still actively driven on the line, the hardware clears the bit as soon as the break condition no longer exists (when the RXD input returns to a high level). 0 – No break condition occurred. 1 – Break condition occurred. URB9 The Received 9th Data Bit holds the ninth data bit, when the UART is configured to op- erate in the 9-bit data format. UXMIP The Transmit In Progress bit indicates when the UART is transmitting. The hardware sets this bit when the UART is transmitting data and clears the bit at the end of the last frame bit. 0 – UART is not transmitting. 1 – UART is transmitting.

21.3.8 UART Interrupt Control Register (UnICTRL)

The UnICTRL register is a byte-wide register that contains the receive and transmit interrupt status bits (read-only bits) and the interrupt enable bits (read/write bits). The register is initialized to 01h at reset. The register format is shown be- low. UTBE The Transmit Buffer Empty bit is set by hard- ware when the UART transfers data from the UnTBUF register to the transmit shift register for transmission. It is automatically cleared by the hardware on the next write to the UnTBUF register. 0 – Transmit buffer is loaded. 1 – Transmit buffer is empty. URBF The Receive Buffer Full bit is set by hardware when the UART has received a complete data frame and has transferred the data from the receive shift register to the UnRBUF register. It is automatically cleared by the hardware when the UnRBUF register is read. 0 – Receive buffer is empty. 1 – Receive buffer is loaded. UDCTS The Delta Clear To Send bit indicates whether the CTS input has changed state since the CPU last read this register. This functionality is only available for the UART0 module. 0 – No change since last read. 1 – State has changed since last read. UCTS The Clear To Send bit indicates the state on the CTS input. This functionality is only avail- able for the UART0 module. 0 – CTS input is high. 1 – CTS input is low. UEFCI The Enable Flow Control Interrupt bit controls whether a flow control interrupt is generated when the UDCTS bit changes from clear to set. This functionality is only available for the UART0 module. 0 – Flow control interrupt disabled. 1 – Flow control interrupt enabled. UETI The Enable Transmitter Interrupt bit, when set, enables generation of an interrupt when the hardware sets the UTBE bit. 0 – Transmit buffer empty interrupt disabled. 1 – Transmit buffer empty interrupt enabled. UERI The Enable Receiver Interrupt bit, when set, enables generation of an interrupt when the hardware sets the URBF bit. 0 – Receive buffer full interrupt disabled. 1 – Receive buffer full interrupt enabled. UEEI The Enable Receive Error Interrupt bit, when set, enables generation of an interrupt when the hardware sets the UERR bit in the Un- STAT register. 0 – Receive error interrupt disabled. 1 – Receive error interrupt enabled.

21.3.9 UART Oversample Rate Register (UnOVR)

The UnOVR register is a byte-wide, read/write register that specifies the oversample rate. At reset, the UnOVR register is cleared. The register format is shown below. UOVSR The Oversampling Rate field specifies the oversampling rate, as given in the following ta- ble. 7 6 5 4 3 2 1 0 UEEI UERI UETI UEFCI UCTS UDCTS URBF UTBE 7 4 3 0 Reserved UOVSR UOVSR3:0 Oversampling Rate 0000–0110 16 0111 7 1000 8 1001 9 1010 10 1011 11 1100 12 1101 13 1110 14 1111 15 Obsolete

155 www.national.com CP3BT23

21.3.10 UART Mode Select Register 2 (UnMDSL2)

The UnMDSL2 register is a byte-wide, read/write register that controls the sample mode used to recover asynchro- nous data. At reset, the UnOVR register is cleared. The reg- ister format is shown below. USMD The USMD bit controls the sample mode for asynchronous transmission. 0 – UART determines the sample position au- tomatically. 1 – The UnSPOS register determines the sample position.

21.3.11 UART Sample Position Register (UnSPOS)

The UnSPOS register is a byte-wide, read/write register that specifies the sample position when the USMD bit in the UnMDSL2 register is set. At reset, the UnSPOS register is initialized to 06h. The register format is shown below. USAMP The Sample Position field specifies the over- sample clock period at which to take the first of three samples for sensing the value of data bits. The clocks are numbered starting at 0 and may range up to 15 for 16× oversampling. The maximum value for this field is (oversam- pling rate - 3). The table below shows the clock period at which each of the three sam- ples is taken, when automatic sampling is en- abled (UnMDSL2.USMD = 0). The USAMP field may be used to override the automatic selection, to choose any other clock period at which to start taking the three sam- ples.

21.4 BAUD RATE CALCULATIONS

The UART baud rate is determined by the System Clock fre- quency and the values in the UnOVR, UnPSR, and Un- BAUD registers. Unless the System Clock is an exact multiple of the baud rate, there will be a small amount of er- ror in the resulting baud rate.

21.4.1 Asynchronous Mode

The equation to calculate the baud rate in asynchronous mode is: where BR is the baud rate, SYS_CLK is the System Clock, O is the oversample rate, N is the baud rate divisor + 1, and P is the prescaler divisor selected by the UPSR register. Assuming a System Clock of 5 MHz, a desired baud rate of 9600, and an oversample rate of 16, the N × P term accord- ing to the equation above is: The N × P term is then divided by each Prescaler Factor from T able 62 to obtain a value closest to an integer. The factor for this example is 6.5. The baud rate register is programmed with a baud rate divi- sor of 4 (N = baud rate divisor + 1). This produces a baud clock of: Note that the percent error is much lower than would be pos- sible without the non-integer prescaler factor. Error greater than 3% is marginal and may result in unreliable operation. Refer to Table 64 below for more examples. 7 1 0 Reserved USMD 7 4 3 0 Reserved USAMP Oversampling Rate Sample Position 123 72 3 4 82 3 4 93 4 5 103 4 5 11 456 124 5 6 135 6 7 145 6 7 156 7 8 166 7 8 BR SYS_CLK NP× 5 6×10() 169 6 0 0×() N 32.552 BR 5 6×10() 16 5 6.5× ×() %error 9615.385 9600–() Obsolete

www.national.com 156 CP3BT23

21.4.2 Synchronous Mode

Synchronous mode is only available for the UART0 module. When synchronous mode is selected and the UCKS bit is set, the UART operates from a clock received on the CKX pin. When the UCKS bit is clear, the UART uses the clock from the internal baud rate generator which is also driven on the CKX pin. When the internal baud rate generator is used, the equation for calculating the baud rate is: where BR is the baud rate, SYS_CLK is the System Clock, N is the value of the baud rate divisor + 1, and P is the pres- caler divide factor selected by the value in the UnPSR reg- ister. Oversampling is not used in synchronous mode. Use the same procedure to determine the values of N and P as in the asynchronous mode. In this case, however, only integer prescaler values are allowed. BR SYS_CLK Table 64 Baud Rate Programming Baud Rate SYS_CLK = 48 MHz SYS_CLK = 24 MHz SYS_CLK = 12 MHz SYS_CLK = 10 MHz ONP % e r r ONP % e r r ONP % e r r ONP % e r r 1 382400 1 0 13.5 0.79 7 12.5 0.79 1536000 9 1 3.5 0.79 8 2 1.0 2.34 Obsolete

157 www.national.com CP3BT23 Table 65 Baud Rate Programming Baud Rate SYS_CLK = 8 MHz SYS_CLK = 6 MHz SYS_CLK = 5 MHz SYS_CLK = 4 MHz ONP % e r r ONP % e r r ONP % e r r ONP % e r r 345600 1 5 11 .5 2.88 7 12.5 0.79 460800 7 12.5 0.79 1 3 11 .0 0.1 6 576000 7 2 1.0 0.79 7 1 1.5 0.79 Baud Rate SYS_CLK = 3 MHz SYS_CLK = 2 MHz SYS_CLK = 1 MHz SYS_CLK = 500 kHz ONP % e r r ONP % e r r ONP % e r r ONP % e r r 115200 13 2 1.0 0.16 7 1 2.5 0.79 128000 16 1 1.5 2.34 8 2 1.0 2.34 230400 13 1 1.0 0.16 Obsolete

22.0 Microwire/SPI Interface

communicating with peripherals. Figure 81. Microwire Interface

22.1 MICROWIRE OPERATION

slave mode), and the serial clock (MSK). serial interface in the device.

22.1.1 Shifting

The Microwire interface is a full duplex transmitter/receiver. starting with the most significant bit first.

Figure 82. Microwire Block Diagram

22.1.2 Reading

is full and a new data transfer sequence starts. read buffer’s higher byte remains unchanged.

22.1.3 Writing

ten to while the BSY bit is set.

22.1.4 Clocking Modes

is sampled on the falling edge of MSK. clock frequencies can be programmed via the MCDV bits. modes with the SCIDL bit clear and set.

22.2 MASTER MODE

low, depending on the SCIDL bit. Figure 83. Normal Mode (SCIDL = 0) Figure 84. Normal Mode (SCIDL = 1) Figure 85. Alternate Mode (SCIDL = 0) Figure 86. Alternate Mode (SCIDL = 1)

161 www.national.com CP3BT23

22.3 SLAVE MODE

In Slave mode, the MSK pin is an input for the shift clock MSK. MDIDO is placed in TRI-STA TE mode when MWCS is inactive. Data transfer is enabled when MWCS is active. The slave starts driving MDIDO when MWCS is active. The most significant bit (lower byte in 8-bit mode or upper byte in 16-bit mode) is output onto the MDIDO pin first. After eight or sixteen clocks (depending on the selected mode), the data transfer is completed. If a new shift process starts before MWDAT was written, i.e., while MWDAT does not contain any valid data, and the ECHO bit is set, the data received from MDODI is transmit- ted on MDIDO in addition to being shifted to MWDAT. If the E C H O bi t is cle ar , t h e da t a t r an sm it t ed o n M D I D O i s t h e data held in the MWDAT register, regardless of its validity. The master may negate the MWCS signal to synchronize the bit count between the master and the slave. In the case that the slave is the only slave in the system, MWCS can be tied to ground.

22.4 INTERRUPT GENERATION

Interrupts may be enabled for any of the conditions shown in Table 66. Figure 87 illustrates the interrupt generation logic of this module. Figure 87. MWSPI Interrupts transfer sequence. Read Buffer Full RBF EIR The read buffer is full and waiting to be unloaded. Overrun OVF EIO A new data transfer sequence started while both the shifter and the read buffer were full. MWSPI Interrupt OVR = 1 EIO RBF = 1 EIR BSY = 0 EIW DS073 Obsolete

22.5 MICROWIRE INTERFACE REGISTERS

22.5.1 Microwire Data Register (MWDAT)

MDIDO pins. The register format is shown below. Figure 88 shows the hardware structure of the register. Figure 88. MWDAT Register

22.5.2 MICROWIRE Control Register (MWCTL1)

bits are cleared. The register format is shown below. Microwire interface module is enabled. 0 – Microwire module disabled. 1 – Microwire module enabled. set, the device operates as the master.

163 www.national.com CP3BT23 MWDAT register is transmitted on MDIDO, whether or not the data is valid. 0 – Echo back disabled. 1 – Echo back enabled. EIO The Enable Interrupt on Overrun bit enables or disables the overrun error interrupt. When set, an interrupt is generated when the Re- ceive Overrun Error bit (MWSTAT.OVR) is set. Otherwise, no interrupt is generated when an overrun error occurs. This bit must only be en- abled in master mode. 0 – Disable overrun error interrupts. 1 – Enable overrun error interrupts. EIR The Enable Interrupt for Read bit controls whether an interrupt is generated when the read buffer becomes full. When set, an inter- rupt is generated when the Read Buffer Full bit (MWSTAT.RBF) is set. Otherwise, no inter- rupt is generated when the read buffer is full. 0 – No read buffer full interrupt. 1 – Interrupt when read buffer becomes full. EIW The Enable Interrupt for Write bit controls whether an interrupt is generated when the Busy bit (MWSTAT.BSY) is cleared, which in- dicates that a data transfer sequence has been completed and the read buffer is ready to receive the new data. Otherwise, no inter- rupt is generated when the Busy bit is cleared. 0 – No interrupt on data transfer complete. 1 – Interrupt on data transfer complete. SCM The Shift Clock Mode bit selects between the normal clocking mode and the alternate clock- ing mode. In the normal mode, the output data is clocked out on the falling edge of MSK and the input data is sampled on the rising edge of MSK. In the alternate mode, the output data is clocked out on the rising edge of MSK and the input data is sampled on the falling edge of MSK. 0 – Normal clocking mode. 1 – Alternate clocking mode. SCIDL The Shift Clock Idle bit controls the value of the MSK output when the Microwire module is idle. This bit must be changed only when the Microwire module is disabled (MEN = 0) or when no bus transaction is in progress (MW- STA T.BSY = 0). 0 – MSK is low when idle. 1 – MSK is high when idle SCDV The Shift Clock Divider Value field specifies the divisor used for generating the MSK shift clock from the System Clock. The divisor is 2 × (SCDV[6:0] + 1). Valid values are 0000001b to 1111111b, so the division ratio may range from 3 to 256. This field is ignored in slave mode (MWCTL1.MNS=0).

22.5.3 Microwire Status Register (MWSTAT)

The MWSTAT register is a word-wide, read-only register that shows the current status of the Microwire interface module. At reset, all non-reserved bits are clear. The regis- ter format is shown below. BSY The Busy bit, when set, indicates that the Mi- crowire shifter is busy. In master mode, the BSY bit is set when the MWDAT register is written. In slave mode, the bit is set on the first leading edge of MSK when MWCS is assert- e d o r w h e n t h e M W D A T r e g i s t e r i s w r i t t e n , whichever occurs first. In both master and slave modes, this bit is cleared when the Mi- crowire data transfer sequence is completed and the read buffer is ready to receive the new data; in other words, when the previous data held in the read buffer has already been read. If the previous data in the read buffer has not been read and new data has been received into the shift register, the BSY bit will not be cleared, as the transfer could not be complet- ed because the contents of the shift register could not be transferred into the read buffer. 0 – Microwire shifter is not busy. 1 – Microwire shifter is busy. RBF The Read Buffer Full bit, when set, indicates that the Microwire read buffer is full and ready to be read by software. It is set when the shifter loads the read buffer, which occurs upon completion of a transfer sequence if the read buffer is empty . The RBF bit is updated when the MWDAT register is read. At that time, the RBF bit is cleared if the shifter does not contain any new data (in other words, the shifter is not receiving data or has not yet re- c e i v e d a f u l l b y t e o f d a t a ) . T h e R B F b i t r e - mains set if the shifter already holds new data at the time that MWDAT is read. In that case, MWDAT is immediately reloaded with the new data and is ready to be read by software. 0 – Microwire read buffer is not full. 1 – Microwire read buffer is full. OVR The Receive Overrun Error bit, when set in master mode, indicates that a receive overrun error has occurred. This error occurs when the read buffer is full, the 8-bit shifter is full, and a new data transfer sequence starts. This bit is undefined in slave mode. The OVR bit, once set, remains set until cleared by soft- ware. Software clears this bit by writing a 1 to its bit position. Writing a 0 to this bit position has no effect. No other bits in the MWSTAT register are affected by a write operation to the register. 0 – No receive overrun error has occurred. 1 – Receive overrun error has occurred. 15 3 2 1 0 Reserved OVR RBF BSY Obsolete

tions with both multiple master and slave devices. its implementation by the ACB module.

23.1 ACB PROTOCOL OVERVIEW

resistors, to keep the signals high when the bus is idle. ceiver (though some peripherals are only receivers).

23.1.1 Data Transactions

sampled during the high phase of the serial clock (SCL). data must be driven during the low phase of the SCL clock. Figure 89. Bit Transfer byte, an Acknowledge signal must follow. by the slave holding SCL low to extend the clock-low period. after each bit, to allow software time to handle this bit. Figure 90. Start and Stop Conditions rection of the data transfer.

www.national.com 166 CP3BT23

23.2 ACB FUNCTIONAL DESCRIPTION

The ACB module provides the physical layer for an AC- CESS.bus compliant serial interface. The module is config- urable as either a master or slave device. As a slave, the ACB module may issue a request to become the bus mas- ter.

23.2.1 Master Mode

An ACCESS.bus transaction starts with a master device re- questing bus mastership. It sends a Start Condition, fol- lowed by the address of the device it wants to access. If this transaction is successfully completed, software can assume that the device has become the bus master. For a device to become the bus master, software should perform the following steps: 1. Set the ACBCTL1.START bit, and configure the ACBCTL1.INTEN bit to the desired operation mode (Polling or Interrupt). This causes the ACB to issue a Start Condition on the ACCESS.bus, as soon as the ACCESS.bus is free (ACBCST.BB=0). It then stalls the bus by holding SCL low. 2. If a bus conflict is detected, (i.e., some other device pulls down the SCL signal before this device does), the ACBST.BER bit is set. 3. If there is no bus conflict, the ACBST .MASTER and ACBST.SDAST bits are set. 4. If the ACBCTL1.INTEN bit is set, and either the ACB- ST.BER bit or the ACBST.SDAST bit is set, an interrupt is sent to the ICU. Sending the Address Byte Once this device is the active master of the ACCESS.bus (ACBST.MASTER = 1), it can send the address on the bus. The address should not be this device’s own address as specified in the ACBADDR.ADDR field if the ACBAD- DR.SAEN bit is set or the ACBADDR2.ADDR field if the ACBADDR2.SAEN bit is set, nor should it be the global call address if the ACBST.GCMTCH bit is set. To send the address byte use the following sequence: 1. Configure the ACBCTL1.INTEN bit according to the de- sired operation mode. For a receive transaction where software wants only one byte of data, it should set the ACBCTL1.ACK bit. If only an address needs to be sent, set the ACBCTL1.STASTRE bit. 2. Write the address byte (7-bit target device address), and the direction bit, to the ACBSDA register. This causes the module to generate a transaction. At the end of this transaction, the acknowledge bit received is copied to the ACBST.NEGACK bit. During the transac- tion, the SDA and SCL signals are continuously checked for conflict with other devices. If a conflict is detected, the transaction is aborted, the ACBST.BER bit is set, and the ACBST .MASTER bit is cleared. 3. If the ACBCTL1.ST ASTRE bit is set, and the transac- tion was successfully completed (i.e., both the ACB- ST.BER and ACBST.NEGACK bits are cleared), the ACBST.STASTR bit is set. In this case, the ACB stalls any further ACCESS.bus operations (i.e., holds SCL low). If the ACBCTL1.INTE bit is set, it also sends an interrupt to the core. 4. If the requested direction is transmit, and the start transaction was completed successfully (i.e., neither the ACBST.NEGACK nor ACBST.BER bit is set, and no other master has accessed the device), the ACB- ST.SDAST bit is set to indicate that the module is wait- ing for service. 5. If the requested direction is receive, the start transac- tion was completed successfully, and the ACBCTL1.ST ASTRE bit is clear, the module starts re- ceiving the first byte automatically. 6. Check that both the ACBST.BER and ACBST.NEGACK bits are clear. If the ACBCTL1.INTEN bit is set, an in- terrupt is generated when either the ACBST.BER or ACBST.NEGACK bit is set. Master Transmit After becoming the bus master, the device can start trans- mitting data on the ACCESS.bus. T o transmit a byte, soft- ware must: 1. Check that the BER and NEGACK bits in the ACBST register are clear and the ACBST .SDAST bit is set. Al- so, if the ACBCTL1.STASTRE bit is set, check that the ACBST .STASTR bit is clear. 2. Write the data byte to be transmitted to the ACBSDA register. When the slave responds with a negative acknowledge, the ACBST.NEGACK bit is set and the ACBST.SDAST bit re- mains cleared. In this case, if the ACBCTL1.INTEN bit is set, an interrupt is sent to the core. Master Receive After becoming the bus master, the device can start receiv- ing data on the ACCESS.bus. To receive a byte, software must: 1. Check that the ACBST.SDAST bit is set and the ACB- ST.BER bit is clear. Also, if the ACBCTL1.STASTRE bit is set, check that the ACBST .STASTR bit is clear. 2. Set the ACBCTL1.ACK bit, if the next byte is the last byte that should be read. This causes a negative ac- knowledge to be sent. 3. Read the data byte from the ACBSDA register. Master Stop A Stop Condition may be issued only when this device is the active bus master (ACBST.MASTRER = 1). T o end a trans- action, set the ACBCTL1.STOP bit before clearing the cur- rent stall bit (i.e., the ACBST.SDAST, ACBST.NEGACK, or ACBST .STASTR bit). This causes the module to send a Stop Condition immediately, and clear the ACBCTL1.STOP bit. Obsolete

167 www.national.com CP3BT23 Master Bus Stall The ACB module can stall the ACCESS.bus between trans- fers while waiting for the core’s response. The ACCESS.bus is stalled by holding the SCL signal low after the acknowl- edge cycle. Note that this is interpreted as the beginning of the following bus operation. Software must make sure that the next operation is prepared before the bit that causes the bus stall is cleared. The bits that can cause a stall in master mode are: ! Negative acknowledge after sending a byte (ACBSTNEGACK = 1). ! ACBST.SDAST bit is set. ! If the ACBCTL1.STASTRE bit is set, after a successful start (ACBST.STASTR = 1). Repeated Start A repeated start is performed when this device is already the bus master (ACBST.MASTER = 1). In this case, the AC- CESS.bus is stalled and the ACB waits for the core handling due to: negative acknowledge (ACBST.NEGACK = 1), emp- ty buffer (ACBST.SDAST = 1), or a stop-after-start (ACB- ST.STASTR = 1). For a repeated start: 1. Set the ACBCTL1.ST ART bit. 2. In master receive mode, read the last data item from the ACBSDA register. 3. Follow the address send sequence, as described in “Sending the Address Byte” on page 166. 4. If the ACB was waiting for handling due to ACB- ST.STASTR = 1, clear it only after writing the requested address and direction to the ACBSDA register. Master Error Detections The ACB detects illegal Start or Stop Conditions (i.e., a Start or Stop Condition within the data transfer, or the ac- knowledge cycle) and a conflict on the data lines of the AC- CESS.bus. If an illegal action is detected, the BER bit is set, and the MASTER mode is exited (the MASTER bit is cleared). Bus Idle Error Recovery When a request to become the active bus master or a re- start operation fails, the ACBST.BER bit is set to indicate the error. In some cases, both this device and the other device may identify the failure and leave the bus idle. In this case, the start sequence may not be completed and the AC- CESS.bus may remain deadlocked. To recover from deadlock, use the following sequence: 1. Clear the ACBST.BER and ACBCST.BB bits. 2. Wait for a time-out period to check that there is no other active master on the bus (i.e., the ACBCST.BB bit re- mains clear). 3. Disable, and re-enable the ACB to put it in the non-ad- dressed slave mode. 4. At this point, some of the slaves may not identify the bus error. To recover, the ACB becomes the bus master by issuing a Start Condition and sends an address field; then issue a Stop Condition to synchronize all the slaves.

23.2.2 Slave Mode

A slave device waits in Idle mode for a master to initiate a bus transaction. Whenever the ACB is enabled, and it is not acting as a master (i.e., ACBST.MASTER = 0), it acts as a slave device. Once a Start Condition on the bus is detected, this device checks whether the address sent by the current master matches either: ! The ACBADDR.ADDR value if the ACBADDR.SAEN bit is set. ! The ACBADDR2.ADDR value if the ACBADDR2.SAEN bit is set. ! The general call address if the ACBCTL1.GCM bit is set. This match is checked even when the ACBST.MASTER bit is set. If a bus conflict (on SDA or SCL) is detected, the ACBST.BER bit is set, the ACBST.MASTER bit is cleared, and this device continues to search the received message for a match. If an address match, or a global match, is de- tected: 1. This device asserts its data pin during the acknowledge cycle. 2. The ACBCST.MATCH, ACBCST.MATCHAF (or ACBCST .GCMTCH if it is a global call address match, or ACBCST.ARPMATCH if it is an ARP address), and ACBST.NMATCH in the ACBCST register are set. If the ACBST .XMIT bit is set (i.e., slave transmit mode), the A CBST .SD AST bit is set to indicate that the b uff er is empty. 3. If the ACBCTL1.INTEN bit is set, an interrupt is gener- ated if both the INTEN and NMINTE bits in the ACBCTL1 register are set. 4. Software then reads the ACBST.XMIT bit to identify the direction requested by the master device. It clears the ACBST .NMATCH bit so future byte transfers are identi- fied as data bytes. Slave Receive and Transmit Slave Receive and Transmit are performed after a match is detected and the data transfer direction is identified. After a byte transfer, the ACB extends the acknowledge clock until software reads or writes the ACBSDA register. The receive and transmit sequence are identical to those used in the master routine. Slave Bus Stall When operating as a slave, this device stalls the AC- CESS.bus by extending the first clock cycle of a transaction in the following cases: — The ACBST.SDAST bit is set. — The ACBST.NMATCH, and ACBCTL1.NMINTE bits are set. Slave Error Detections The ACB detects illegal Start and Stop Conditions on the ACCESS.bus (i.e., a Start or Stop Condition within the data transfer or the acknowledge cycle). When an illegal Start or Stop Condition is detected, the BER bit is set and the MATCH and GMATCH bits are cleared, causing the module to be an unaddressed slave. Obsolete

www.national.com 168 CP3BT23 Power Down When this device is in Power Save, Idle, or Halt mode, the ACB module is not active but retains its status. If the ACB is enabled (ACBCTL2.ENABLE = 1) on detection of a Start Condition, a wake-up signal is issued to the MIWU module. Use this signal to switch this device to Active mode. The ACB module cannot check the address byte for a match following the start condition that caused the wake-up event for this device. The ACB responds with a negative acknowl- edge, and the device should resend both the Start Condition and the address after this device has had time to wake up. Check that the ACBCST.BUSY bit is inactive before entering Power Save, Idle, or Halt mode. This guarantees that the de- vice does not acknowledge an address sent and stop re- sponding later.

23.2.3 SDA and SCL Pins Configuration

The SDA and SCL pins are driven as open-drain signals. For more information, see the I/O configuration section.

23.2.4 ACB Clock Frequency Configuration

The ACB module permits software to set the clock frequen- cy used for the ACCESS.bus clock. The clock is set by the ACBCTL2.SCLFRQ field. This field determines the SCL clock period used by this device. This clock low period may be extended by stall periods initiated by the ACB module or by another ACCESS.bus device. In case of a conflict with another bus master, a shorter clock high period may be forced by the other bus master until the conflict is resolved. 23.3 ACCESS.BUS INTERFACE REGISTERS The ACCESS.bus interface uses the registers listed in Table 68.

23.3.1 ACB Serial Data Register (ACBSDA)

The ACBSDA register is a byte-wide, read/write shift regis- ter used to transmit and receive data. The most significant bit is transmitted (received) first and the least significant bit is transmitted (received) last. Reading or writing to the ACB- SDA register is allowed when ACBST.SDAST is set; or for repeated starts after setting the START bit. An attempt to access the register in other cases produces unpredictable results.

23.3.2 ACB Status Register (ACBST)

The ACBST register is a byte-wide, read-only register that maintains current ACB status. When reset, disabled, or in Halt or Idle modes, ACBST is cleared. XMIT The Direction Bit bit is set when the ACB mod- ule is currently in master/slave transmit mode. Otherwise it is cleared. 0 – Receive mode. 1 – Transmit mode. MASTER The Master bit indicates that the module is currently in master mode. It is set when a re- quest for bus mastership succeeds. It is cleared upon arbitration loss (BER is set) or the recognition of a Stop Condition. 0 – Slave mode. 1 – Master mode. NMATCH The New match bit is set when the address byte following a Start Condition, or repeated starts, causes a match or a global-call match. The NMATCH bit is cleared when written with 1. Writing 0 to NMATCH is ignored. If the ACBCTL1.INTEN bit is set, an interrupt is sent when this bit is set. 0 – No match. 1 – Match or global-call match. STASTR The Stall After Start bit is set by the successful completion of an address sending (i.e., a Start Condition sent without a bus error, or negative acknowledge), if the ACBCTL1.ST ASTRE bit is set. This bit is ignored in slave mode. When the STASTR bit is set, it stalls the bus by pull- ing down the SCL line, and suspends any oth- er action on the bus (e.g., receives first byte in master receive mode). In addition, if the A CBCT L1.I NTEN bit is set , it also sends an interrupt to the core. Writing 1 to the STASTR bit clears it. It is also cleared when the module is disabled. Writing 0 to the ST ASTR bit has no effect. 0 – No stall after start condition. 1 – Stall after successful start. Table 68 ACCESS.bus Interface Registers Name Address Description ACBSDA FF F2A0h ACB Serial Data Register ACBST FF F2A2h ACB Status Register ACBCST FF F2A4h ACB Control Status Register ACBCTL1FF F2A6h ACB Control Register 1 ACBCTL2 FF F2AAh ACB Control Register 2 ACBCTL3 FF F2AEh ACB Control Register 3 ACBADDR1FF F2A8h ACB Own Address Register 1 ACBADDR2 FF F2ACh ACB Own Address Register 2 7 0 DATA 7 6 5 4 3 2 1 0 SLVSTP SDAST BER NEGACK STASTR NMATCH MASTER XMIT Obsolete

169 www.national.com CP3BT23 NEGACK The Negative Acknowledge bit is set by hard- ware when a transmission is not acknowl- edged on the ninth clock. (In this case, the SDAST bit is not set.) Writing 1 to NEGACK clears it. It is also cleared when the module is disabled. Writing 0 to the NEGACK bit is ig- nored. 0 – No transmission not acknowledged condi- tion. 1 – Transmission not acknowledged. BER The Bus Error bit is set by the hardware when a Start or Stop Condition is detected during data transfer (i.e., Start or Stop Condition dur- ing the transfer of bits 2 through 8 and ac- knowledge cycle), or when an arbitration problem is detected. Writing 1 to the BER bit clears it. It is also cleared when the module is disabled. Writing 0 to the BER bit is ignored. 0 – No bus error occurred. 1 – Bus error occurred. SDAST The SDA Status bit indicates that the SDA data register is waiting for data (transmit, as master or slave) or holds data that should be read (receive, as master or slave). This bit is cleared when reading from the ACBSDA reg- ister during a receive, or when written to dur- ing a transmit. When the ACBCTL1.START bit is set, reading the ACBSDA register does not clear the SDAST bit. This enables the ACB to send a repeated start in master receive mode. 0 – ACB module is not waiting for data trans- fer. 1 – ACB module is waiting for data to be load- ed or unloaded. SLVSTP The Slave Stop bit indicates that a Stop Con- dition was detected after a slave transfer (i.e., after a slave transfer in which MATCH or GCMATCH is set). Writing 1 to SLVSTP clears it. It is also cleared when the module is dis- abled. Writing 0 to SLVSTP is ignored. 0 – No stop condition after slave transfer oc- curred. 1 – Stop condition after slave transfer oc- curred.

23.3.3 ACB Control Status Register (ACBCST)

The ACBCST register is a byte-wide, read/write register that maintains current ACB status. When reset, disabled, or in Halt or Idle modes, the non-reserved bits of ACBCST are cleared. BUSY The BUSY bit indicates that the ACB module is: ! Generating a Start Condition ! In Master mode (ACBST .MASTER is set) ! I n S l a v e m o d e ( A C B C S T . M A T C H o r ACBCST.GCMTCH is set) ! In the period between detecting a Start and completing the reception of the ad- dress byte. After this, the ACB either be- comes not busy or enters slave mode. The BUSY bit is cleared by the completion of any of the above states, and by disabling the module. BUSY is a read only bit. It must al- ways be written with 0. 0 – ACB module is not busy. 1 – ACB module is busy. BB The Bus Busy bit indicates the bus is busy. It is set when the bus is active (i.e., a low level on either SDA or SCL) or by a Start Condition. It is cleared when the module is disabled, on detection of a Stop Condition, or when writing 1 to this bit. See “Usage Hints” on page 172 for a description of the use of this bit. This bit should be set when either the SDA or SCL sig- nals are low. This is done by sampling the SDA and SCL signals continuously and set- ting the bit if one of them is low. The bit re- mains set until cleared by a STOP condition or written with 1. 0 – Bus is not busy. 1 – Bus is busy. M A T C H T h e A d d r e s s M a t c h b i t i n d i c a t e s i n s l a v e mode when ACBADDR.SAEN is set and the first seven bits of the address byte (the first byte transferred after a Start Condition) matches the 7-bit address in the ACBADDR register, or when ACBADDR2.SAEN is set and the first seven bits of the address byte matches the 7-bit address in the ACBADDR2 register. It is cleared by Start Condition or re- peated Start and Stop Condition (including il- legal Start or Stop Condition). 0 – No address match occurred. 1 – Address match occurred. 7 6 5 4 3 2 1 0 Reserved TGSCL TSDA GCMTCH MATCH BB BUSY Obsolete

www.national.com 170 CP3BT23 GCMTCH The Global Call Match bit is set in slave mode when the ACBCTL1.GCMEN bit is set and the address byte (the first byte transferred after a Start Condition) is 00h. It is cleared by a Start Condition or repeated Start and Stop Condi- tion (including illegal Start or Stop Condition). 0 – No global call match occurred. 1 – Global call match occurred. TSDA The Test SDA bit samples the state of the SDA signal. This bit can be used while recovering from an error condition in which the SDA sig- n a l i s c o n s t a n t l y p u l l e d l o w b y a s l a v e t h a t went out of sync. This bit is a read-only bit. Data written to it is ignored. TGSCL The Toggle SCL bit enables toggling the SCL signal during error recovery. When the SDA signal is low, writing 1 to this bit drives the SCL signal high for one cycle. Writing 1 to TGSCL when the SDA signal is high is ignored. The bit is cleared when the clock toggle is completed. 0 – Writing 0 has no effect. 1 – Writing 1 toggles the SDA signal high for one cycle.

23.3.4 ACB Control Register 1 (ACBCTL1)

The ACBCTL1 register is a byte-wide, read/write register that configures and controls the ACB module. When reset, disabled, or in Halt or Idle modes, the ACBCTL1 register is cleared. START The Start bit is set to generate a Start Condi- tion on the ACCESS.bus. The START bit is cleared when the Start Condition is sent, or upon detection of a Bus Error (ACBST .BER = 1). This bit should be set only when in Master mode, or when requesting Master mode. If this device is not the active master of the bus (ACBST.MASTER = 0), set- ting the START bit generates a Start Con0dition as soon as the ACCESS.bus is free (ACBCST.BB = 0). An address send se- quence should then be performed. If this de- vice is the active master of the bus (ACBST.MASTER = 1), when the START bit is set, a write to the ACBSDA register generates a Start Condition, then the ACBSDA data is transmitted as the slave’s address and the re- quested transfer direction. This case is a re- peated Start Condition. It may be used to switch the direction of the data flow between the master and the slave, or to choose anoth- er slave device without using a Stop Condition in between. 0 – Writing 0 has no effect. 1 – Writing 1 generates a Start condition. STOP The Stop bit in master mode generates a Stop Condition that completes or aborts the current message transfer. This bit clears itself after the Stop condition is issued. 0 – Writing 0 has no effect. 1 – Writing 1 generates a Stop condition. 7 6 5 4 3 2 1 0 STASTRE NMINTE GCMEN ACK Res. INTEN STOP ST ART Obsolete

171 www.national.com CP3BT23 INTEN The Interrupt Enable bit controls generating ACB interrupts. When the INTEN bit is cleared ACB interrupt is disabled. When the INTEN bit is set, interrupts are enabled. 0 – ACB interrupts disabled. 1 – ACB interrupts enabled. An interrupt is generated (the interrupt signals to the ICU is high) on any of the following events: ! An address MATCH is detected (ACB- ST.NMATCH = 1) and the NMINTE bit is set. ! A Bus Error occurs (ACBST.BERR = 1). ! Negative acknowledge after sending a byte (ACBST.NEGACK = 1). ! An interrupt is generated on acknowledge of each transaction (same as hardware setting the ACBST.SDAST bit). ! If ACBCTL1.STASTRE = 1, in master mode after a successful start (ACBST.STASTR = 1). ! Detection of a Stop Condition while in slave receive mode (ACBST.SLVSTP = 1). ACK The Acknowledge bit holds the value this de- vice sends in master or slave mode during the next acknowledge cycle. Setting this bit to 1 instructs the transmitting device to stop send- ing data, since the receiver either does not need, or cannot receive, any more data. This bit is cleared after the first acknowledge cycle. This bit is ignored when in transmit mode. GCMEN The Global Call Match Enable bit enables the match of an incoming address byte to the gen- eral call address (Start Condition followed by address byte of 00h) while the ACB is in slave mode. When cleared, the ACB does not re- spond to a global call. 0 – Global call matching disabled. 1 – Global call matching enabled. NMINTE The New Match Interrupt Enable controls whether ACB interrupts are generated on new matches. Set the NMINTE bit to enable the in- terrupt on a new match (i.e., when ACB- ST.NMATCH is set). The interrupt is issued only if the ACBCTL1.INTEN bit is set. 0 – New match interrupts disabled. 1 – New match interrupts enabled. S T A S T R E T h e S t a l l A f t e r S t a rt E n a b l e b i t e n a b l e s t h e stall after start mechanism. When enabled, the ACB is stalled after the address byte. When the STASTRE bit is clear, the ACB- ST.STASTR bit is always clear. 0 – No stall after start. 1 – Stall-after-start enabled.

23.3.5 ACB Control Register 2 (ACBCTL2)

The ACBCTL2 register is a byte-wide, read/write register that controls the module and selects the ACB clock rate. At reset, the ACBCTL2 register is cleared. ENABLE The Enable bit controls the ACB module. When this bit is set, the ACB module is en- abled. When the Enable bit is clear, the ACB module is disabled, the ACBCTL1, ACBST, and ACBCST registers are cleared, and the clocks are halted. 0 – ACB module disabled. 1 – ACB module enabled. SCLFRQ The SCL Frequency field specifies the SCL period (low time and high time) in master mode. The clock low time and high time are defined as follows: t SCLl = tSCLh = 2 × SCLFRQ × tCLK Where tCLK is this device’s clock period when in Active mode. The SCLFRQ field may be programmed to values in the range of 0001000b through 1111111b. Using any other value has unpredictable results.

23.3.6 ACB Control Register 3 (ACBCTL3)

The ACBCTL3 register is a byte-wide, read/write register that expands the clock prescaler field and enables ARP matches. At reset, the ACBCTL3 register is cleared. ARPMEN The ARP Match Enable bit enables the matching of an incoming address byte to the SMBus ARP address 110 0001b general call address (Start condition followed by address byte of 00h), while the ACB is in slave mode. 0 – ACB does not respond to ARP address- es. 1 – ARP address matching enabled. SCLFRQ The SCL Frequency field specifies the SCL period (low time and high time) in master mode. The ACBCTL3 register provides a 2-bit expansion of this field, with the remaining 7 bits being held in the ACBCTL2 register. 7 1 0 SCLFRQ6:0 ENABLE 7 3 2 1 0 Reserved ARPMEN SCLFRQ8:7 Obsolete

www.national.com 172 CP3BT23

23.3.7 ACB Own Address Register 1 (ACBADDR1)

The ACBADDR1 register is a byte-wide, read/write register that holds the module’s first ACCESS.bus address. After re- set, its value is undefined. ADDR The Own Address field holds the first 7-bit AC- CESS.bus address of this device. When in s l a v e m o d e , t h e f i r s t 7 b i t s r e c e i v e d a f t e r a Start Condition are compared to this field (first bit received to bit 6, and the last to bit 0). If the address field matches the received data and the SAEN bit is set, a match is detected. SAEN The Slave Address Enable bit controls wheth- er address matching is performed in slave mode. When set, the SAEN bit indicates that the ADDR field holds a valid address and en- ables the match of ADDR to an incoming ad- dress byte. When cleared, the ACB does not check for an address match. 0 – Address matching disabled. 1 – Address matching enabled0.

23.3.8 ACB Own Address Register 2 (ACBADDR2)

The ACBADDR2 register is a byte-wide, read/write register that holds the module’s second ACCESS.bus address. After reset, its value is undefined. ADDR The Own Address field holds the second 7-bit ACCESS.bus address of this device. When in s l a v e m o d e , t h e f i r s t 7 b i t s r e c e i v e d a f t e r a Start Condition are compared to this field (first bit received to bit 6, and the last to bit 0). If the address field matches the received data and the SAEN bit is set, a match is detected. SAEN The Slave Address Enable bit controls wheth- er address matching is performed in slave mode. When set, the SAEN bit indicates that the ADDR field holds a valid address and en- ables the match of ADDR to an incoming ad- dress byte. When cleared, the ACB does not check for an address match. 0 – Address matching disabled. 1 – Address matching enabled.

23.4 USAGE HINTS

! When the ACB module is disabled, the ACBCST.BB bit is cleared. After enabling the ACB (ACBCTL2.ENABLE = 1) in systems with more than one master, the bus may be in the middle of a transaction with another device, which is not reflected in the BB bit. There is a need to allow the ACB to synchronize to the bus activity status before issu- ing a request to become the bus master, to prevent bus errors. Therefore, before issuing a request to become the bus master for the first time, software should check that there is no activity on the bus by checking the BB bit after the bus allowed time-out period. ! When waking up from power down, before checking the ACBCST.MATCH bit, test the ACBCST.BUSY bit to make sure that the address transaction has finished. ! The BB bit is intended to solve a deadlock in which two, or more, devices detect a usage conflict on the bus and both devices cease being bus masters at the same time. In this situation, the BB bits of both devices are active (because each deduces that there is another master cur- rently performing a transaction, while in fact no device is executing a transaction), and the bus would stay locked until some device sends a ACBCTL1.STOP condition. The ACBCST.BB bit allows software to monitor bus us- age, so it can avoid sending a STOP signal in the middle of the transaction of some other device on the bus. This bit detects whether the bus remains unused over a cer- tain period, while the BB bit is set. ! In some cases, the bus may get stuck with the SCL or SDA lines active. A possible cause is an erroneous Start or Stop Condition that occurs in the middle of a slave re- ceive session. When the SCL signal is stuck active, there is nothing that can be done, and it is the responsibility of the module that holds the bus to release it. When the SDA signal is stuck active, the ACB module enables the release of the bus by using the following sequence. Note that in normal cases, the SCL signal may be toggled only by the bus master. This protocol is a recovery scheme which is an exception that should be used only in the case when there is no other master on the bus. The re- covery scheme is as follows: 1. Disable and re-enable the module to set it into the not addressed slave mode. 2. Set the ACBCTL1.ST ART bit to make an attempt to issue a Start Condition. 3. Check if the SDA signal is active (low) by reading ACBCST.TSDA bit. If it is active, issue a single SCL cycle by writing 1 to ACBCST .TGSCL bit. If the SDA line is not active, continue from step 5. 4. Check if the ACBST .MASTER bit is set, which indi- cates that the Start Condition was sent. If not, repeat step 3 and 4 until the SDA signal is released. 5. Clear the BB bit. This enables the START bit to be ex- ecuted. Continue according to “Bus Idle Error Recov- ery” on page 167. 7 6 0 SAEN ADDR 7 6 0 SAEN ADDR Obsolete

173 www.national.com CP3BT23

23.4.1 Avoiding Bus Error During Write Transaction

A Bus Error (BER) may occur during a write transaction if the data register is written at a very specific time. The mod- ule generates one system-clock cycle setup time of SDA to SCL vs. the minimum time of the clock divider ratio. The problem can be masked within the driver by dynamical- ly dividing-by-half the SCL width immediately after the slave address is successfully sent and before writing to the ACB- SDA register. This has the effect of forcing SCL into the stretch state. The following code example is the relevant segment of the ACCESS.bus driver addressing this issue. ; NAME: ACBRead Reads "Count" byte(s) from selected I2C Slave. If read address differs from previous ; Read or Write operation (as recorded in NextAddress), a "dummy" write transaction is ; initiated to reset the address to the desired location. This is followed by a repeated ; Start sequence and the Read transaction. All transactions begin with a call to ACBStartX ; which sends the Start condition and Slave address. Checks for errors throughout process. ; PARAMETERS: UBYTE Slave - Slave Device Address. Must be of format 0xXXXX0000 ; UWORD Addrs - Byte/Array address (extended addressing mode uses two byte address) ; UWORD Count - Number of bytes to read ; UBYTE *buf - Pointer to receive buffer ; CALLS: ACBStartX ; RETURNED: error status UWORD ACBRead (UBYTE Slave, UWORD Addrs, UWORD Count, UBYTE *buf) ACB_T *acb; UBYTE err, *rcv; UWORD Timeout; acb = (ACB_T*)ACB_ADDRESS; /* Set pointer to ACB module */ /* If the indicated address differs from the last */ if (Addrs != NextAddress) { /* recorded access (i.e. Random Read), we must first */ /* send a "dummy" write to the desired new address.. */ NextAddress = Addrs; /* Update last address placeholder */ KeyInit(); KBD_OUT &= ~BIT0; /* Send start bit and Slave address... */ if ((err = ACBStartX (Slave | (Addrs >> 7 & 0x0E), ACB_WRITE, 0))) return (err); /* If unsuccessful, return error code */ // KBD_OUT &= ~BIT0; acb->ACBsda = (UBYTE)Addrs; /* Send new address byte */ KBD_OUT &= ~BIT0; Timeout = 1000; /* Set timeout */ /* Wait for xmitter to be ready...zzzzzzzzz */ while (!(acb->ACBst & ACBSDAST) && !(acb->ACBst & ACBBER) && Timeout--); if (acb->ACBst & ACBBER) { /* If a bus error occurs while sending address, clear */ acb->ACBst |= ACBBER; /* the error flag and return error status */ return (ACBERR_COLLISION); KBD_OUT &= ~BIT0; if (!Timeout) /* If we timeout, return error */ return (ACBERR_TIMEOUT); /* (Re)Send start bit and Slave address... */ if ((err = ACBStartX (Slave | (Addrs >> 7 & 0x0E), ACB_READ, Count))) /* If error, return */ return (err); rcv = buf; /* Get address of read buffer */ /* Read Count bytes into user’s buffer */ while (Count) { if (Count-- == 1) /* If this the final byte, or only one requested, send */ acb->ACBctl1 |= ACBACK; /* the NACK bit after reception */ Timeout = 1000; /* Set timeout */ while (!(acb->ACBst & ACBSDAST) && Timeout--); if (!Timeout) /* Timed out?? */ /* YES - return error */ return (ACBERR_TIMEOUT); *rcv++ = acb->ACBsda; /* NO - Read byte from Recv register */ /* Adjust current address placeholder */ NextAddress++; Obsolete

www.national.com 174 CP3BT23 acb->ACBctl1 |= ACBSTOP; /* Send STOP bit */ /* Return success status.... */ return (ACB_NOERR); ; NAME: ACBStartX Initiates an ACB bus transaction by sending the Start bit, followed by the Slave address ; and R/W flag. Checks for any ACB errors throughout this sequence and returns status. ; PARAMETERS: UBYTE Slave - I2C address of Slave device ; UBYTE R_nW - Read/Write flag (0x01 or 0x00) ; UWORD Count - Desired number of bytes (read/write) ; CALLS: ; RETURNED: error/success UWORD ACBStartX (UBYTE Slave, UBYTE R_nW, UWORD Count) ACB_T *acb; UWORD Timeout; /* Get address of ACB module */ acb = (ACB_T*)ACB_ADDRESS; /* If Bus is Busy and we’re NOT the Master, return err */ if (acb->ACBcst & ACBBB && !(acb->ACBst & ACBMASTER)) return (ACBERR_NOTMASTER); /* If we’re good to go, send Start condition */ acb->ACBctl1 |= ACBSTART; /* Check if we’re the Bus Master with timeout */ Timeout = 100; while (!(acb->ACBst & ACBSDAST) && Timeout--) /* Related to bus error problem */ if (acb->ACBst & ACBBER) { /* If collision occurs, clear error and return status */ acb->ACBst |= ACBBER; return (ACBERR_COLLISION); if (!Timeout) /* If timeout, we must NOT be the Master...signal error */ return (ACBERR_NOTMASTER); /* Now, send the address and R/W flag... */ acb->ACBsda = Slave | R_nW; /* Send address and R/W flag */ Timeout = 1000; /* Failsafe for lockup */ /* Wait for address to be sent and ACK’d */ while (!(acb->ACBst & ACBSDAST) && !(acb->ACBst & ACBNEGACK)&& --Timeout) { if (acb->ACBst & ACBBER) { /* If a bus error occurs while sending address, clear */ acb->ACBst |= ACBBER; /* the error flag and return error status */ return (ACBERR_COLLISION); KBD_OUT |= BIT0; // OScope marker if (!Timeout) /* If timeout, signal error */ return (ACBERR_TIMEOUT); /* Or if Slave does not reply, report busy/error */ else if (acb->ACBst & ACBNEGACK) return (ACBERR_NEGACK); /* Otherwise return success */ else { return (ACB_NOERR); Obsolete

24.0 Timing and Watchdog Module

locked, only reset can release it.

24.1 TWM STRUCTURE

the Watchdog section on the bottom.

24.2 TIMER T0 OPERATION

Figure 94. Timing and Watchdog Module Block Diagram rupt is also available through this alternative mechanism. cally upon restart of the 16-bit timer. to complete before performing the switch. TWW/MT0 Register T0CSR Contrl. Reg.

www.national.com 176 CP3BT23

24.3 WATCHDOG OPERATION

The Watchdog is an 8-bit down counter that operates on the rising edge of a specified clock source. At reset, the Watch- dog is disabled; it does not count and no Watchdog signal is generated. A write to either the Watchdog Count (WDCNT) register or the Watchdog Service Data Match (WDSDM) register starts the counter. The Watchdog counter counts down from the value programmed in the WDCNT register. Once started, only a reset can stop the Watchdog from op- erating. The Watchdog can be programmed to use either T0OUT or T0IN as its clock source (the output and input of Timer T0, respectively). The TWCFG.WDCT0I bit controls this clock selection. Software must periodically “service” the Watchdog. There are two ways to service the Watchdog, the choice depend- ing on the programmed value of the WDSDME bit in the Timer and Watchdog Configuration (TWCFG) register. If the TWCFG.WDSDME bit is clear, the Watchdog is ser- viced by writing a value to the WDCNT register. The value written to the register is reloaded into the Watchdog counter. The counter then continues counting down from that value. If the TWCFG.WDSDME bit is set, the Watchdog is ser- viced by writing the value 5Ch to the Watchdog Service Data Match (WDSDM) register. This reloads the Watchdog counter with the value previously programmed into the WD- CNT register. The counter then continues counting down from that value. A Watchdog error signal is generated by any of the following events: ! The Watchdog serviced too late. ! The Watchdog serviced too often. ! The WDSDM register is written with a value other than 5Ch when WDSDM type servicing is enabled (TWCFG.WDSDME = 1). A Watchdog error condition resets the device.

24.3.1 Register Locking

The Timer and Watchdog Configuration (TWCFG) register is used to set the Watchdog configuration. It controls the Watchdog clock source (T0IN or T0OUT), the type of Watchdog servicing (using WDCNT or WDSDM), and the locking state of the TWCFG, TWCPR, TIMER0, T0CSR, and WDCNT registers. A register that is locked cannot be read or written. A write operation is ignored and a read op- eration returns unpredictable results. If the TWCFG register is itself locked, it remains locked until the device is reset. Any other locked registers also remain locked until the device is reset. This feature prevents a run- away program from tampering with the programmed Watch- dog function.

24.3.2 Power Save Mode Operation

The Timer and Watchdog Module is active in both the Power Save and Idle modes. The clocks and counters continue to operate normally in these modes. The WDSDM register is accessible in the Power Save and Idle modes, but the other TWM registers are accessible only in the Active mode. Therefore, Watchdog servicing must be carried out using the WDSDM register in the Power Save or Idle mode. In the Halt mode, the entire device is frozen, including the Timer and Watchdog Module. On return to Active mode, op- eration of the module resumes at the point at which it was stopped. Note: After a restart or Watchdog service through WDCNT, do not enter Power Save mode for a period equivalent to 5 Slow Clock cycles.

24.4 TWM REGISTERS

The TWM registers controls the operation of the Timing and Watchdog Module. There are six such registers: The WDSDM register is accessible in both Active and Pow- er Save mode. The other TWM registers are accessible only in Active mode. Table 69 TWM Registers Name Address Description TWCFG FF FF20h Timer and Watchdog Configuration Register TWCP FF FF22h Timer and Watchdog Clock Prescaler Register TWMT0 FF FF24h TWM Timer 0 Register T0CSR FF FF26h TWMT0 Control and Status Register WDCNT FF FF28h Watchdog Count Register WDSDM FF FF2Ah Watchdog Service Data Match Register Obsolete

177 www.national.com CP3BT23

24.4.1 Timer and Watchdog Configuration Register

(TWCFG) The TWCFG register is a byte-wide, read/write register that selects the Watchdog clock input and service method, and also allows the Watchdog registers to be selectively locked. A locked register cannot be read or written; a read operation returns unpredictable values and a write operation is ig- nored. Once a lock bit is set, that bit cannot be cleared until the device is reset. At reset, the non-reserved bits of the register are cleared. The register format is shown below. LTWCFG The Lock TWCFG Register bit controls ac- cess to the TWCFG register. When clear, ac- cess to the TWCFG register is allowed. When set, the TWCFG register is locked. 0 – TWCFG register unlocked. 1 – TWCFG register locked. LTWCP The Lock TWCP Register bit controls access to the TWCP register. When clear, access to the TWCP register is allowed. When set, the TWCP register is locked. 0 – TWCP register unlocked. 1 – TWCP register locked. LTWMT0 The Lock TWMT0 Register bit controls access to the TWMT0 register. When clear, access to the TWMT0 and T0CSR registers are al- lowed. When set, the TWMT0 and T0CSR registers are locked. 0 – TWMT0 register unlocked. 1 – TWMT0 register locked. LWDCNT The Lock LDWCNT Register bit controls ac- cess to the LDWCNT register. When clear, ac- cess to the LDWCNT register is allowed. When set, the LDWCNT register is locked. 0 – LDWCNT register unlocked. 1 – LDWCNT register locked. WDCT0I The Watchdog Clock from T0IN bit selects the clock source for the Watchdog timer. When clear, the T0OUT signal (the output of Timer T0) is used as the Watchdog clock. When set, the T0IN signal (the prescaled Slow Clock) is used as the Watchdog clock. 0 – Watchdog timer is clocked by T0OUT. 1 – Watchdog timer is clocked by T0IN. WDSDME The Watchdog Service Data Match Enable bit controls which method is used to service the Watchdog timer. When clear, Watchdog ser- vicing is accomplished by writing a count val- ue to the WDCNT register; write operations to the Watchdog Service Data Match (WDSDM) register are ignored. When set, Watchdog servicing is accomplished by writing the value 5Ch to the WDSDM register. 0 – Write a count value to the WDCNT regis- ter to service the Watchdog timer. 1 – Write 5Ch to the WDSDM register to ser- vice the Watchdog timer.

24.4.2 Timer and Watchdog Clock Prescaler Register

(TWCP) The TWCP register is a byte-wide, read/write register that specifies the prescaler value used for dividing the low-fre- quency clock to generate the T0IN clock. At reset, the non- reserved bits of the register are cleared. The register format is shown below. MDIV Main Clock Divide. This 3-bit field defines the prescaler factor used for dividing the low speed device clock to create the T0IN clock. The allowed 3-bit values and the correspond- ing clock divisors and clock rates are listed be- low.

24.4.3 TWM Timer 0 Register (TWMT0)

The TWMT0 register is a word-wide, read/write register that defines the T0OUT interrupt rate. At reset, TWMT0 register is initialized to FFFFh. The register format is shown below. PRESET The Timer T0 Preset field holds the value used to reload Timer T0 on each underflow. Therefore, the frequency of the Timer T0 in- terrupt is the frequency of T0IN divided by (PRESET+1). The allowed values of PRESET are 0001h through FFFFh. 7 6 5 4 3 2 1 0 Res. WDSDME WDCT0I LWDCNT LTWMT0 LTWCP LTWCFG 7 3 2 0 Reserved MDIV MDIV Clock Divisor (fSCLK = 32.768 kHz) T0IN Frequency 000 132.768 kHz 0012 1 6.384 kHz 010 4 8.192 kHz 011 8 4.096 kHz 100 16 2.056 kHz 101 32 1.024 kHz Other Reserved N/A 15 0 PRESET Obsolete

www.national.com 178 CP3BT23

24.4.4 TWMT0 Control and Status Register (T0CSR)

The T0CSR register is a byte-wide, read/write register that controls Timer T0 and shows its current status. At reset, the non-reserved bits of the register are cleared. The register format is shown below. RST The Restart bit is used to reset Timer T0. When this bit is set, it forces the timer to re- load the value in the TWMT0 register on the next rising edge of the selected input clock. The RST bit is reset automatically by the hard- ware on the same rising edge of the selected input clock. Writing a 0 to this bit position has no effect. At reset, the non-reserved bits of the register are cleared. 0 – Writing 0 has no effect. 1 – Writing 1 resets Timer T0. TC The Terminal Count bit is set by hardware when the Timer T0 count reaches zero and is cleared when software reads the T0CSR reg- ister. It is a read-only bit. Any data written to this bit position is ignored. The TC bit is not cleared if FREEZE mode is asserted by an ex- ternal debugging system. 0 – Timer T0 did not count down to 0. 1 – Timer T0 counted down to 0. T0INTE The Timer T0 Interrupt Enable bit enables an interrupt to the CPU each time the Timer T0 count reaches zero. When this bit is clear, Timer T0 interrupts are disabled. 0 – Timer T0 interrupts disabled. 1 – Timer T0 interrupts enabled. WDLTD The Watchdog Last Touch Delay bit is set when either WDCNT or WDSDM is written and the data transfer to the Watchdog is in progress (see WDCNT and WDSDM register description). When clear, it is safe to switch to Power Save mode. 0 – No data transfer to the Watchdog is in progress, safe to enter Power Save mode. 1 – Data transfer to the Watchdog in progress. FRZT0E The Freeze Timer0 Enable bit controls wheth- er TImer 0 is stopped in FREEZE mode. If this bit is set, the Timer 0 is frozen (stopped) when the FREEZE input to the TWM is asserted. If the FRZT0E bit is clear, only the Watchdog timer is frozen by asserting the FREEZE input signal. After reset, this bit is clear. 0 – Timer T0 unaffected by FREEZE mode. 1 – Timer T0 stopped in FREEZE mode.

24.4.5 Watchdog Count Register (WDCNT)

The WDCNT register is a byte-wide, write-only register that holds the value that is loaded into the Watchdog counter each time the Watchdog is serviced. The Watchdog is start- ed by the first write to this register. Each successive write to this register restarts the Watchdog count with the written value. At reset, this register is initialized to 0Fh.

24.4.6 Watchdog Service Data Match Register

(WDSDM) The WSDSM register is a byte-wide, write-only register used for servicing the Watchdog. When this type of servic- ing is enabled (TWCFG.WDSDME = 1), the Watchdog is serviced by writing the value 5Ch to the WSDSM register. Each such servicing reloads the Watchdog counter with the value previously written to the WDCNT register. Writing any data other than 5Ch triggers a Watchdog error. Writing to the register more than once in one Watchdog clock cycle also triggers a Watchdog error signal. If this type of servic- ing is disabled (TWCFG.WDSDME = 0), any write to the WSDSM register is ignored.

24.5 WATCHDOG PROGRAMMING

The highest level of protection against software errors is achieved by programming and then locking the Watchdog registers and using the WDSDM register for servicing. This is the procedure: 1. Write the desired values into the TWM Clock Prescaler register (TWCP) and the TWM Timer 0 register (TWMT0) to control the T0IN and T0OUT clock rates. The frequency of T0IN can be programmed to any of six frequencies ranging from 1/32 × f SLCLK to fSLCLK . The frequency of T0OUT is equal to the frequency of T0IN divided by (1+ PRESET), in which PRESET is the value written to the TWMT0 register. 2. Configure the Watchdog clock to use either T0IN or T0OUT by setting or clearing the TWCFG.WDCT0I bit. 3. Write the initial value into the WDCNT register. This starts operation of the Watchdog and specifies the maximum allowed number of Watchdog clock cycles between service operations. 4. Set the T0CSR.RST bit to restart the TWMT0 timer. 5. Lock the Watchdog registers and enable the Watchdog Service Data Match Enable function by setting bits 0, 1, 2, 3, and 5 in the TWCFG register. 6. Service the Watchdog by periodically writing the value 5Ch to the WDSDM register at an appropriate rate. Servicing must occur at least once per period pro- grammed into the WDCNT register, but no more than once in a single Watchdog input clock cycle. 7 5 4 3 2 1 0 Reserved FRZT0E WDLTD T0INTE TC RST 7 0 PRESET 7 0 RSTDATA Obsolete

25.0 Multi-Function Timer

also provides a general-purpose timer/counter. timing signals or counts occurrences of external events. vides one external event counter and one system timer.

25.1 TIMER STRUCTURE

Figure 95. Multi-Function Timer Block Diagram

25.1.1 Timer/Counter Block

than one-fourth the speed of the 32.768 kHz System Clock.

25.1.2 Clock Source Block

Clock Source block is shown in Figure 96. Figure 96. Multi-Function Timer Clock Source

counter are both cleared upon reset. the TB pin is used as one of the two capture inputs. the TB pin is used as one of the two capture inputs. Figure 97. Pulse-Accumulate Mode no more than one-fourth the speed of the System Clock. pulses are at least the size of the whole slow-clock period. much slower rate than the original System Clock. System Clock resumes operation. ers stop counting until the System Clock resumes operation.

25.2 TIMER OPERATING MODES

25.2.1 Mode 1: Processor-Independent PWM

general-purpose timer/counter. downward from the loaded value. rupts can be enabled or disabled under software control. the hardware on each occurrence of a timer reload. Figure 98. Processor-Independent PWM Mode

25.2.2 Mode 2: Dual Input Capture

TB pin transfers the timer contents to the TCRB register. signal with a minimum of CPU overhead. reflect the elapsed time between transitions on the TA pin. equal to or greater than one System Clock cycle. TAIEN, TBIEN, and TCIEN, respectively. Figure 99. Dual-Input Capture Mode

25.2.3 Mode 3: Dual Independent Timer/Counter

clocked by the prescaled System Clock. any further action from the CPU. Figure 100. Dual-Independent Timer/Counter Mode

25.2.4 Mode 4: Input Capture Plus Timer

input rather than two inputs. Timer/Counter 1 (TCNT1) operates the same as in Mode 3. further action from the CPU. ther rising or falling edges. register and then the counter is preset to FFFFh. reflect the elapsed time between transitions on the TA pin. greater than one System Clock cycle. events are TBIEN and TDIEN, respectively. Figure 101. Input Capture Plus Timer Mode

185 www.national.com CP3BT23

25.3 TIMER INTERRUPTS

The Multi-Function Timer unit has four interrupt sources, designated A, B, C, and D. Interrupt sources A, B, and C are mapped into a single system interrupt called Timer Interrupt 1, while interrupt source D is mapped into a system interrupt called Timer Interrupt 2. Each of the four interrupt sources has its own enable bit and pending bit. The enable bits are named TAIEN, TBIEN, TCIEN, and TDIEN. The pending bits are named TAPND, TBPND, TCPND, and TDPND. Timer Interrupts 1 and 2 are system interrupts TA and TB (IRQ14 and IRQ13), respectively. Table 70 shows the events that trigger interrupts A, B, C, and D in each of the four operating modes. Note that some interrupt sources are not used in some operating modes.

25.4 TIMER I/O FUNCTIONS

The Multi-Function Timer unit uses two I/O pins, called TA and TB. The function of each pin depends on the timer op- erating mode and the TAEN and TBEN enable bits. Table 71 shows the functions of the pins in each operating mode, and for each combination of enable bit settings. When the TA pin is configured to operate as a PWM output (TAEN = 1), the state of the pin is toggled on each underflow of the TCNT1 counter. In this case, the initial value on the pin is determined by the TAOUT bit. For example, to start with T A high, software must set the T A OUT bit bef ore en- abling the timer clock. This option is available only when the timer is configured to operate in Mode 1, 3, or 4 (in other words, when TCRA is not used in Capture mode). Table 70 Timer Interrupts Overview Sys. Int. Interrupt Pending Bit Mode 1 Mode 2 Mode 3 Mode 4 PWM + Counter Dual Input Capture + Counter Dual Counter Single Capture + Counter Timer Int. 1 (TA Int.) TAPND TCNT1 reload from TCRA Input capture on TA transition TCNT1 reload from TCRA TCNT1 reload from TCRA TBPND TCNT1 reload from TCRB Input Capture on TB transition N/A Input Capture on TB transition TCPND N/A TCNT1 underflow N/A N/A Timer Int. 2 (TB Int.) TDPND TCNT2 underflow TCNT2 underflow TCNT2 reload from TCRB TCNT2 underflow Table 71 Timer I/O Functions I/O TAEN TBEN Mode 1 Mode 2 Mode 3 Mode 4 PWM + Counter Dual Input Capture + counter Dual Counter Single Capture + counter TA TAEN = 0 TBEN = X No Output Capture TCNT1 into TCRA No Output Toggle No Output Toggle TAEN = 1 TBEN = X Toggle Output on Underflow of TCNT1 Capture TCNT1 into TCRA and Preset TCNT1 T oggle Output on Underflow of TCNT1 Toggle Output on Underflow of TCNT1 TB TAEN = X TBEN = 0 Ext. Event or Pulse Accumulate Input Capture TCNT1 into TCRB Ext. Event or Pulse Accumulate Input Capture TCNT2 into TCRB TAEN = X TBEN = 1 Ext. Event or Pulse Accumulate Input Capture TCNT1 into TCRB and Preset TCNT1 Ext. Event or Pulse Accumulate Input Capture TCNT2 into TCRB and Preset TCNT2 Obsolete

www.national.com 186 CP3BT23

25.5 TIMER REGISTERS

Table 72 lists the CPU-accessible registers used to control the Multi-Function Timers.

25.5.1 Clock Prescaler Register (TPRSC)

The TPRSC register is a byte-wide, read/write register that holds the current value of the 5-bit clock prescaler (CLKPS). This register is cleared on reset. The register format is shown below. CLKPS The Clock Prescaler field specifies the divisor used to generate the Timer Clock from the System Clock. When the timer is configured to use the prescaled clock, the System Clock is divided by (CLKPS + 1) to produce the timer clock. Therefore, the System Clock divisor can range from 1 to 32.

25.5.2 Clock Unit Control Register (TCKC)

The TCKC register is a byte-wide, read/write register that selects the clock source for each timer/counter. Selecting the clock source also starts the counter. This register is cleared on reset, which disables the timer/counters. The register format is shown below. C1CSEL The Counter 1 Clock Select field specifies the clock mode for Timer/Counter 1 as follows: 000 – No clock (Timer/Counter 1 stopped, modes 1, 2, and 3 only). 001 – Prescaled System Clock. 010 – External event on TB (modes 1 and 3 only). 011 – Pulse-accumulate mode based on TB (modes 1 and 3 only). 100 – Slow Clock.* 101 – Reserved. 110 – Reserved. 111 – Reserved. C2CSEL The Counter 2 Clock Select field specifies the clock mode for Timer/Counter 2 as follows: 000 – No clock (Timer/Counter 2 stopped, modes 1, 2, and 3 only). 001 – Prescaled System Clock. 010 – External event on TB (modes 1 and 3 only). 011 – Pulse-accumulate mode based on TB (modes 1 and 3 only). 100 – Slow Clock* 101 – Reserved. 110 – Reserved. 111 – Reserved. * Operation of the Slow Clock is determined by the CRC- TRL.SCLK control bit, as described in Section 11.9.1.

25.5.3 Timer/Counter 1 Register (TCNT1)

The TCNT1 register is a word-wide, read/write register that holds the current count value for Timer/Counter 1. The reg- ister contents are not affected by a reset and are unknown after power-up.

25.5.4 Timer/Counter 2 Register (TCNT2)

The TCNT2 register is a word-wide, read/write register that holds the current count value for Timer/Counter 2. The reg- ister contents are not affected by a reset and are unknown after power-up. Table 72 Multi-Function Timer Registers Name Address Description TPRSC FF FF48h Clock Prescaler Register TCKC FF FF4Ah Clock Unit Control Register TCNT1FF FF40h Timer/Counter 1 Register TCNT2 FF FF46h Timer/Counter 2 Register TCRA FF FF42h Reload/Capture A Register TCRB FF FF44h Reload/Capture B Register TCTRL FF FF4Ch Timer Mode Control Register TICTL FF FF4Eh Timer Interrupt Control Register TICLR FF FF50h Timer Interrupt Clear Register 7 5 4 0 Reserved CLKPS 7 6 5 3 2 0 Reserved C2CSEL C1CSEL 15 0 TCNT1 15 0 TCNT2 Obsolete

187 www.national.com CP3BT23

25.5.5 Reload/Capture A Register (TCRA)

The TCRA register is a word-wide, read/write register that holds the reload or capture value for Timer/Counter 1. The register contents are not affected by a reset and are un- known after power-up.

25.5.6 Reload/Capture B Register (TCRB)

The TCRB register is a word-wide, read/write register that holds the reload or capture value for Timer/Counter 2. The register contents are not affected by a reset and are un- known after power-up.

25.5.7 Timer Mode Control Register (TCTRL)

The TCTRL register is a byte-wide, read/write register that sets the operating mode of the timer/counter and the T A and TB pins. This register is cleared at reset. The register format is shown below. MDSEL The Mode Select field sets the operating mode of the timer/counter as follows: 00 – Mode 1: PWM plus system timer. 01 – Mode 2: Dual-Input Capture plus system timer. 10 – Mode 3: Dual Timer/Counter. 11 – Mode 4: Single-Input Capture and Sin- gle Timer. TAEDG The TA Edge Polarity bit selects the polarity of the edges that trigger the TA input. 0 – TA input is sensitive to falling edges (high to low transitions). 1 – T A input is sensitive to rising edges (low to high transitions). TBEDG The TB Edge Polarity bit selects the polarity of the edges that trigger the TB input. In pulse- accumulate mode, when this bit is set, the counter is enabled only when TB is high; when this bit is clear, the counter is enabled only when TB is low. 0 – TB input is sensitive to falling edges (high to low transitions). 1 – TB input is sensitive to rising edges (low to high transitions). TAEN The TA Enable bit controls whether the TA pin is enabled to operate as a preset input or as a PWM output, depending on the timer operat- ing mode. In Mode 2 (Dual Input Capture), a transition on the TA pin presets the TCNT1 counter to FFFFh. In the other modes, TA functions as a PWM output. When this bit is clear, operation of the pin for the timer/counter is disabled. 0 – TA input disabled. 1 – TA input enabled. TBEN The TB Enable bit controls whether the TB pin in enabled to operate in Mode 2 (Dual Input Capture) or Mode 4 (Single Input Capture and Single Timer). A transition on the TB pin pre- sets the corresponding timer/counter to FFFFh (TCNT1 in Mode 2 or TCNT2 in Mode 4). When this bit is clear, operation of the pin for the timer/counter is disabled. This bit set- ting has no effect in Mode 1 or Mode 3. 0 – TB input disabled. 1 – TB input enabled. TAOUT The TA Output Data bit indicates the current state of the TA pin when the pin is used as a PWM output. The hardware sets and clears this bit, but software can also read or write this bit at any time and therefore control the state of the output pin. In case of conflict, a software write has precedence over a hardware up- date. This bit setting has no effect when the TA pin is used as an input. 0 – TA pin is low. 1 – TA pin is high. TEN The Timer Enable bit controls whether the Multi-Function Timer is enabled. When the module is disabled all clocks to the counter unit are stopped to minimize power consump- tion. For that reason, the timer/counter regis- ters (TCNT1 and TCNT2), the capture/reload registers (TCRA and TCRB), and the interrupt pending bits (TXPND) cannot be written in this mode. Also, the 5-bit clock prescaler and the interrupt pending bits are cleared, and the TA I/O pin becomes an input. 0 – Multi-Function Timer is disabled. 1 – Multi-Function Timer is enabled. 15 0 TCRA 15 0 TCRB 7 6 5 4 3 2 1 0 TEN TAOUT TBEN TAEN TBEDG TAEDG MDSEL Obsolete

www.national.com 188 CP3BT23

25.5.8 Timer Interrupt Control Register (TICTL)

The TICTL register is a byte-wide, read/write register that contains the interrupt enable bits and interrupt pending bits for the four timer interrupt sources, designated A, B, C, and D. The condition that causes each type of interrupt depends on the operating mode, as shown in Table 70. This register is cleared upon reset. The register format is shown below. TAPND The Timer Interrupt Source A Pending bit indi- cates that timer interrupt condition A has oc- curred. For an explanation of interrupt conditions A, B, C, and D, see T able 70. This bit can be set by hardware or by software. To clear this bit, software must use the Timer In- terrupt Clear Register (TICLR). Attempting to directly write a 0 to this bit is ignored. 0 – Interrupt source A has not triggered. 1 – Interrupt source A has triggered. TBPND The Timer Interrupt Source B Pending bit indi- cates that timer interrupt condition B has oc- curred. For an explanation of interrupt conditions A, B, C, and D, see T able 70. This bit can be set by hardware or by software. To clear this bit, software must use the Timer In- terrupt Clear Register (TICLR). Attempting to directly write a 0 to this bit is ignored. 0 – Interrupt source B has not triggered. 1 – Interrupt source B has triggered. TCPND The Timer Interrupt Source C Pending bit in- dicates that timer interrupt condition C has oc- curred. For an explanation of interrupt conditions A, B, C, and D, see T able 70. This bit can be set by hardware or by software. To clear this bit, software must use the Timer In- terrupt Clear Register (TICLR). Attempting to directly write a 0 to this bit is ignored. 0 – Interrupt source C has not triggered. 1 – Interrupt source C has triggered. TDPND The Timer Interrupt Source D Pending bit in- dicates that timer interrupt condition D has oc- curred. For an explanation of interrupt conditions A, B, C, and D, see T able 70. This bit can be set by hardware or by software. To clear this bit, software must use the Timer In- terrupt Clear Register (TICLR). Attempting to directly write a 0 to this bit is ignored. 0 – Interrupt source D has not triggered. 1 – Interrupt source D has triggered. TAIEN The Timer Interrupt A Enable bit controls whether an interrupt is generated on each oc- currence of interrupt condition A. For an ex- planation of interrupt conditions A, B, C, and D, see Table 70. 0 – Condition A interrupts disabled. 1 – Condition A interrupts enabled. TBIEN The Timer Interrupt B Enable bit controls whether an interrupt is generated on each oc- currence of interrupt condition B. For an ex- planation of interrupt conditions A, B, C, and D, see Table 70. 0 – Condition B interrupts disabled. 1 – Condition B interrupts enabled. TCIEN The Timer Interrupt C Enable bit controls whether an interrupt is generated on each oc- currence of interrupt condition C. For an ex- planation of interrupt conditions A, B, C, and D, see Table 70. 0 – Condition C interrupts disabled. 1 – Condition C interrupts enabled. TDIEN The Timer Interrupt D Enable bit controls whether an interrupt is generated on each oc- currence of interrupt condition D. For an ex- planation of interrupt conditions A, B, C, and D, see Table 70. 0 – Condition D interrupts disabled. 1 – Condition D interrupts enabled.

25.5.9 Timer Interrupt Clear Register (TICLR)

The TICLR register is a byte-wide, write-only register that al- lows software to clear the TAPND, TBPND, TCPND, and TDPND bits in the Timer Interrupt Control (TICTRL) regis- ter. Do not modify this register with instructions that access the register as a read-modify-write operand, such as the bit manipulation instructions. The register reads as FFh. The register format is shown below. TACLR The Timer Pending A Clear bit is used to clear the Timer Interrupt Source A Pending bit (TAPND) in the Timer Interrupt Control regis- ter (TICTL). 0 – Writing a 0 has no effect. 1 – Writing a 1 clears the TAPND bit. TBCLR The Timer Pending A Clear bit is used to clear the Timer Interrupt Source B Pending bit (TB- PND) in the Timer Interrupt Control register (TICTL). 0 – Writing a 0 has no effect. 1 – Writing a 1 clears the TBPND bit. TCCLR The Timer Pending C Clear bit is used to clear the Timer Interrupt Source C Pending bit (TCPND) in the Timer Interrupt Control regis- ter (TICTL). 0 – Writing a 0 has no effect. 1 – Writing a 1 clears the TCPND bit. TDCLR The Timer Pending D Clear bit is used to clear the Timer Interrupt Source D Pending bit (TD- PND) in the Timer Interrupt Control register (TICTL). 0 – Writing a 0 has no effect. 1 – Writing a 1 clears the TDPND bit. 7 6 5 4 3 2 1 0 TDIEN TCIEN TBIEN TAIEN TDPND TCPND TBPND TAPND 7 4 3 2 1 0 Reserved TDCLR TCCLR TBCLR TACLR Obsolete

26.0 Versatile Timer Unit (VTU)

to accommodate a wide range of system frequencies.

26.1 VTU FUNCTIONAL DESCRIPTION

or capture inputs depending on the mode of operation. a 16-bit PWM timer, or as a dual 16-bit capture timer. Figure 102 shows the main elements of the VTU. Figure 102. Versatile Timer Unit Block Diagram

26.1.1 Dual 8-bit PWM Mode

ments at the rate determined by the clock prescaler. counter increment. Figure 103 illustrates this concept. Figure 103. VTU PWM Generation duty cycle to be programmed in a range from 0% to 100%. turn the most recent value written to it. the counter value and the PERCAPx register value occurs. The counter will then be cleared and continue counting up. case the counter will count up to FFh, then roll over to 00h. 00h to 01h transition of the counter. counter register while either timer is running will be ignored.

as independent PWM outputs in the dual 8-bit PWM mode. defined by the IOxCTL.PxPOL bit. ! The counter will stop and will retain its last value. MODE.TxRUN bits are cleared. to the other three timer subsystems. Figure 104. VTU Dual 8-Bit PWM Mode nated to form a single 16-bit counter. to the other three timer subsystems. Figure 105. VTU 16-bit PWM Mode

26.1.3 Dual 16-Bit Capture Mode

duty cycle of external signals. Starting the counter is identical to the 16-bit PWM mode, i.e. event inputs are enabled once the MODE.TxRUN bit is set. ative transition or both a positive and a negative transition. duty cycle measurement of an external signal.

to the other three timer subsystems. Figure 106. VTU Dual 16-bit Capture Mode

26.1.4 Low Power Mode

registers of a timer subsystem while it is in low-power mode. All registers can be read at any time.

26.1.5 Interrupts

Figure 107. VTU Interrupt Request Structure which cause an interrupt pending bit to be set.

26.1.6 ISE Mode operation

ture input events are re-enabled.

193 www.national.com CP3BT23

26.2 VTU REGISTERS

The VTU contains a total of 19 user accessible registers, as listed in Table 74. All registers are word-wide and are initial- ized to a known value upon reset. All software accesses to the VTU registers must be word accesses.

26.2.1 Mode Control Register (MODE)

The MODE register is a word-wide read/write register which controls the mode selection of all four timer subsystems. The register is clear after reset. TxRUN The Timer Run bit controls whether the corre- sponding timer is stopped or running. If set, the associated counter and clock prescaler is started depending on the mode of operation. Once set, the clock to the clock prescaler and the counter are enabled and the counter will increment each time the clock prescaler counter value matches the value defined in the associated clock prescaler field (CxPR- SC). 0 – Timer stopped. 1 – Timer running. TMODx The Timer System Operating Mode field en- ables or disables the Timer Subsystem and defines its operating mode. 00 – Low-Power Mode. A l l c l o c k s t o t h e counter subsystem are stopped. The counter is stopped regardless of the val- ue of the TxRUN bits. Read operations to the Timer Subsystem will return the last value; software must not perform any write operations to the Timer Sub- s y s t e m w h i l e i t i s d i s a b l e d s i n c e t h o s e will be ignored. 01 – D u a l 8 - b i t P W M m o d e . Each 8-bit counter may individually be started or stopped via its associated TxRUN bit. The TIOx pins will function as PWM out- puts. 10 – 16-bit PWM mode. The two 8-bit counters are concatenated to form a sin- gle 16-bit counter. The counter may be started or stopped with the lower of the two TxRUN bits, i.e. T1RUN, T3RUN, T5RUN, and T7RUN. The TIOx pins will function as PWM outputs. 11 – Capture Mode. Both 8-bit counters are concatenated and operate as a single 16-bit counter. The counter may be start- ed or stopped with the lower of the two TxRUN bits, i.e., T1RUN, T3RUN, T5RUN, and T7RUN. The TIOx pins will function as capture inputs. Table 74 VTU Registers Name Address Description MODE FF FF80h Mode Control Register IO1CTL FF FF82h I/O Control Register 1 IO2CTL FF FF84h I/O Control Register 2 INTCTL FF FF86h Interrupt Control Register INTPND FF FF88h Interrupt Pending Register CLK1PS FF FF8Ah Clock Prescaler Register 1 CLK2PS FF FF98h Clock Prescaler Register 2 COUNT1FF FF8Ch Counter 1 Register PERCAP1FF FF8Eh Period/Capture 1 Register DTYCAP1FF FF90h Duty Cycle/Capture 1 Register COUNT2 FF FF92h Counter 2 Register PERCAP2 FF FF94h Period/Capture 2 Register DTYCAP2 FF FF96h Duty Cycle/Capture 2 Register COUNT3 FF FF9Ah Counter 3 Register PERCAP3 FF FF9Ch Period/Capture 3 Register DTYCAP3 FF FF9Eh Duty Cycle/Capture 3 Register COUNT4 FF FFA0h Counter 4 Register PERCAP4 FF FFA2h Period/Capture 4 Register DTYCAP4 FF FFA4h Duty Cycle/Capture 4 Register 7 6 5 4 3 2 1 0 TMOD2 T4RUN T3RUN TMOD1 T2RUN T1RUN 15 14 13 12 11 10 9 8 TMOD4 T8RUN T7RUN TMOD3 T6RUN T5RUN Obsolete

www.national.com 194 CP3BT23

26.2.2 I/O Control Register 1 (IO1CTL)

The I/O Control Register 1 (IO1CTL) is a word-wide read/ write register. The register controls the function of the I/O pins TIO1 through TIO4 depending on the selected mode of operation. The register is clear after reset. CxEDG The Capture Edge Control field specifies the polarity of a capture event and the reset of the counter. The value of this three bit field has no effect while operating in PWM mode. PxPOL The PWM Polarity bit selects the output polar- ity. While operating in PWM mode the bit specifies the polarity of the corresponding PWM output (TIOx). Once a counter is stopped, the output will assume the value of PxPOL, i.e., its initial value. The PxPOL bit has no effect while operating in capture mode. 0 – The PWM output goes high at the 00h to 01h transition of the counter and will go low once the counter value matches the duty cycle value. 1 – The PWM output goes low at the 00h to 01h transition of the counter and will go high once the counter value matches the duty cycle value.

26.2.3 I/O Control Register 2 (IO2CTL)

The IO2CTL register is a word-wide read/write register. The register controls the functionality of the I/O pins TIO5 through TIO8 depending on the selected mode of operation. The register is cleared at reset. The functionality of the bit fields of the IO2CTL register is identical to the ones described in the IO1CTL register sec- tion.

26.2.4 Interrupt Control Register (INTCTL)

The INTCTL register is a word-wide read/write register. It contains the interrupt enable bits for all 16 interrupt sources of the VTU. Each interrupt enable bit corresponds to an in- terrupt pending bit located in the Interrupt Pending Register (INTPND). All INTCTL register bits are solely under soft- ware control. The register is clear after reset. IxAEN The Timer x Interrupt A Enable bit controls in- terrupt requests triggered on the correspond- ing IxAPD bit being set. The associated IxAPD bit will be updated regardless of the value of the IxAEN bit. 0 – Disable system interrupt request for the IxAPD pending bit. 1 – Enable system interrupt request for the Ix- APD pending bit. IxBEN The Timer x Interrupt B Enable bit controls in- terrupt requests triggered on the correspond- ing IxBPD bit being set. The associated IxBPD bit will be updated regardless of the value of the IxBEN bit. 0 – Disable system interrupt request for the IxBPD pending bit. 1 – Enable system interrupt request for the Ix- BPD pending bit. 7 6 4 3 2 0 P2POL C2EDG P1POL C1EDG 15 14 12 11 10 8 P4POL C4EDG P3POL C3EDG CxEDG Capture Counter Reset

000 Rising edge No

001 Falling edge No

010 Rising edge Ye s

011 Falling edge Ye s

100 Both edges No

101 Both edges Rising edge

110 Both edges Falling edge

111 Both edges Both edges

I2DEN I2CEN I2BEN I2AEN I1DEN I1CEN I1BEN I1AEN 15 14 13 12 11 10 9 8 I4DEN I4CEN I4BEN I4AEN I3DEN I3CEN I3BEN I3AEN Obsolete

195 www.national.com CP3BT23 IxCEN The Timer x Interrupt C Enable bit controls in- terrupt requests triggered on the correspond- ing IxCPD bit being set. The associated IxCPD bit will be updated regardless of the value of the IxCEN bit. 0 – Disable system interrupt request for the IxCPD pending bit. 1 – Enable system interrupt request for the Ix- CPD pending bit. IxDEN Timer x Interrupt D Enable bit controls inter- rupt requests triggered on the corresponding IxDPD bit being set. The associated IxDPD bit will be updated regardless of the value of the IxDEN bit. 0 – Disable system interrupt request for the IxDPD pending bit. 1 – Enable system interrupt request for the IxDPD pending bit.

26.2.5 Interrupt Pending Register (INTPND)

The INTPND register is a word-wide read/write register which contains all 16 interrupt pending bits. There are four interrupt pending bits called IxAPD through IxDPD for each timer subsystem. Each interrupt pending bit is set by a hard- ware event and can be cleared if software writes a 1 to the bit position. The value will remain unchanged if a 0 is written to the bit position. All interrupt pending bits are cleared (0) upon reset. IxAPD The Timer x Interrupt A Pending bit indicates that an interrupt condition for the related timer subsystem has occurred. Table 73 on page 192 lists the hardware condition which causes this bit to be set. 0 – No interrupt pending. 1 – Timer interrupt condition occurred. IxBPD The Timer x Interrupt B Pending bit indicates that an interrupt condition for the related timer subsystem has occurred. Table 73 on page 192 lists the hardware condition which causes this bit to be set. 0 – No interrupt pending. 1 – Timer interrupt condition occurred. IxCPD The Timer x Interrupt C Pending bit indicates that an interrupt condition for the related timer subsystem has occurred. Table 73 on page 192 lists the hardware condition which causes this bit to be set. 0 – No interrupt pending. 1 – Timer interrupt condition occurred. IxDPD The Timer x Interrupt D Pending bit indicates that an interrupt condition for the related timer subsystem has occurred. Table 73 on page 192 lists the hardware condition which causes this bit to be set. 0 – No interrupt pending. 1 – Timer interrupt condition occurred.

26.2.6 Clock Prescaler Register 1 (CLK1PS)

The CLK1PS register is a word-wide read/write register. The register is split into two 8-bit fields called C1PRSC and C 2P R S C . E ac h f i el d ho lds t h e 8- b it c lo c k p r es ca ler c om - pare value for timer subsystems 1 and 2 respectively. The register is cleared at reset. C1PRSC The Clock Prescaler 1 Compare Value field holds the 8-bit prescaler value for timer sub- system 1. The counter of timer subsystem is incremented each time when the clock pres- caler compare value matches the value of the clock prescaler counter. The division ratio is equal to (C1PRSC + 1). For example, 00h is a ratio of 1, and FFh is a ratio of 256. C2PRSC The Clock Prescaler 2 Compare Value field holds the 8-bit prescaler value for timer sub- system 2. The counter of timer subsystem is incremented each time when the clock pres- caler compare value matches the value of the clock prescaler counter. The division ratio is equal to (C2PRSC + 1).

26.2.7 Clock Prescaler Register 2 (CLK2PS)

The Clock Prescaler Register 2 (CLK2PS) is a word-wide read/write register. The register is split into two 8-bit fields called C3PRSC and C4PRSC. Each field holds the 8-bit clock prescaler compare value for timer subsystems 3 and 4 respectively. The register is cleared at reset. C3PRSC The Clock Prescaler 3 Compare Value field holds the 8-bit prescaler value for timer sub- system 3. The counter of timer subsystem is incremented each time when the clock pres- caler compare value matches the value of the clock prescaler counter. The division ratio is equal to (C3PRSC + 1). C4PRSC The Clock Prescaler 4 Compare Value field holds the 8-bit prescaler value for timer sub- system 4. The counter of timer subsystem is incremented each time when the clock pres- caler compare value matches the value of the clock prescaler counter. The division ratio is equal to (C4PRSC + 1). 7 6 5 4 3 2 1 0 I2DPD I2CPD I2BPD I2APD I1DPD I1CPD I1BPD I1APD 15 14 13 12 11 10 9 8 I4DPD I4CPD I4BPD I4APD I3DPD I3CPD I3BPD I3APD 15 8 7 0 C2PRSC C1PRSC 15 8 7 0 C4PRSC C3PRSC Obsolete

www.national.com 196 CP3BT23

26.2.8 Counter Register n (COUNTx)

The Counter (COUNTx) registers are word-wide read/write registers. There are a total of four registers called COUNT1 through COUNT4, one for each of the four timer sub- systems. Software may read the registers at any time. Reading the register will return the current value of the counter. The register may only be written if the counter is stopped (i.e. if both TxRUN bits associated with a timer sub- system are clear). The registers are cleared at reset.

26.2.9 Period/Capture Register n (PERCAPx)

The PERCAPx registers are word-wide read/write registers. There are a total of four registers called PERCAP1 through PERCAP4, one for each timer subsystem. The registers hold the period compare value in PWM mode of the counter value at the time the last associated capture event occurred. In PWM mode the register is double buffered. If a new peri- od compare value is written while the counter is running, the write will not take effect until counter value matches the pre- vious period compare value or until the counter is stopped. Reading may take place at any time and will return the most recent value which was written. The PERCAPx registers are cleared at reset.

26.2.10 Duty Cycle/Capture Register n (DTYCAPx)

The Duty Cycle/Capture (DTYCAPx) registers are word- wide read/write registers. There are a total of four registers called DTYCAP1 through DTYCAP4, one for each timer subsystem. The registers hold the period compare value in PWM mode or the counter value at the time the last associ- ated capture event occurred. In PWM mode, the register is double buffered. If a new duty cycle compare value is written while the counter is running, the write will not take effect un- til the counter value matches the previous period compare value or until the counter is stopped. The update takes effect on period boundaries only. Reading may take place at any time and will return the most recent value which was written. The DTYCAPx registers are cleared at reset. 15 0 CNTx 15 0 PCAPx 15 0 DCAPx Obsolete

197 www.national.com CP3BT23

27.0 Register Map

Table 75 is a detailed memory map showing the specific memory address of the memory, I/O ports, and registers. The table shows the starting address, the size, and a brief description of each memory block and register. For detailed information on using these memory locations, see the appli- cable sections in the data sheet. All addresses not listed in the table are reserved and must not be read or written. An attempt to access an unlisted ad- dress will have unpredictable results. Each byte-wide register occupies a single address and can be accessed only in a byte-wide transaction. Each word- wide register occupies two consecutive memory addresses and can be accessed only in a word-wide transaction. Both the byte-wide and word-wide registers reside at word boundaries (even addresses). Therefore, each byte-wide register uses only the lowest eight bits of the internal data bus. Most device registers are read/write registers. However, some registers are read-only or write-only, as indicated in the table. An attempt to read a write-only register or to write a read-only register will have unpredictable results. When software writes to a register in which one or more bits are reserved, it must write a zero to each reserved bit unless indicated otherwise in the description of the register. Read- ing a reserved bit returns an undefined value. Table 75 Detailed Device Mapping Register Name Size Address Access Type Value After Reset Comments Bluetooth LLC Registers PLN Byte 0E F180h Write-Only WHITENING_CHANNEL_SELECTION Byte 0E F181h Write-Only SINGLE_FREQUENCY_SELECTION Byte 0E F182h Write-Only LN_BT_CLOCK_0 Byte 0E F198h Read-Only LN_BT_CLOCK_1Byte 0E F1 99h Read-Only LN_BT_CLOCK_2 Byte 0E F19Ah Read-Only LN_BT_CLOCK_3 Byte 0E F19Bh Read-Only RX_CN Byte 0E F19Ch Read-Only TX_CN Byte 0E F19Dh Read-Only AC_ACCEPTLVL Word 0E F19Eh Write-Only LAP_ACCEPTLVL Byte 0E F1A0h Write-Only RFSYNCH_DELAY Byte 0E F1A1h Write-Only SPI_READ Word 0E F1A2h Read-Only SPI_MODE_CONFIG Byte 0E F1A4h Write-Only M_COUNTER_0 Byte 0E F1A6h Read/Write M_COUNTER_1Byte 0E F1 A7h Read/Write M_COUNTER_2 Byte 0E F1A8h Read/Write N_COUNTER_0 Byte 0E F1AAh Write-Only N_COUNTER_1Byte 0E F1 ABh Write-Only BT_CLOCK_WR_0 Byte 0E F1ACh Write-Only BT_CLOCK_WR_1Byte 0E F1 ADh Write-Only BT_CLOCK_WR_2 Byte 0E F1AEh Write-Only BT_CLOCK_WR_3 Byte 0E F1AFh Write-Only Obsolete

www.national.com 198 CP3BT23WTPTC_1SLOT Word 0E F1B0h Write-Only WTPTC_3SLOT Word 0E F1B2h Write-Only WTPTC_5SLOT Word 0E F1B4h Write-Only SEQ_RESET Byte 0E F1B6h Write-Only SEQ_CONTINUE Byte 0E F1B7h Write-Only RX_STATUS Byte 0E F1B8h Read-Only CHIP_ID Byte 0E F1BAh Read-Only INT_VECTOR Byte 0E F1BCh Read-Only SYSTEM_CLK_EN Byte 0E F1BEh Write-Only LINKTIMER_WR_RD Word 0E F1C0h Read-Only LINKTIMER_SELECT Byte 0E F1C2h Read-Only LINKTIMER_STATUS_EXP_FLAG Byte 0E F1C4h Read-Only LINKTIMER_STATUS_RD_WR_FLAG Byte 0E F1C5h Read-Only LINKTIMER_ADJUST_PLUS Byte 0E F1C6h Read-Only LINKTIMER_ADJUST_MINUS Byte 0E F1C7h Read-Only SLOTTIMER_WR_RD Byte 0E F1C8h Read-Only CAN0 Module Message Buffers CMB0_CNSTAT Word 0E F000h Read/Write XXXXh CMB0_TSTP Word 0E F002h Read/Write XXXXh CMB0_DATA3 Word 0E F004h Read/Write XXXXh CMB0_DATA2 Word 0E F006h Read/Write XXXXh CMB0_DATA1Word 0E F008h Read/Write XXXXh CMB0_DATA0 Word 0E F00Ah Read/Write XXXXh CMB0_ID0 Word 0E F00Ch Read/Write XXXXh CMB0_ID1Word 0E F00Eh Read/Write XXXXh CMB18-word 0E F010h– 0E F01Fh Read/Write XXXXh Same register layout as CMB0. CMB2 8-word 0E F020h– 0E F02Fh Read/Write XXXXh Same register layout as CMB0. CMB3 8-word 0E F030h– 0E F03Fh Read/Write XXXXh Same register layout as CMB0. CMB4 8-word 0E F040h– 0E F04Fh Read/Write XXXXh Same register layout as CMB0. CMB5 8-word 0E F050h– 0E F05Fh Read/Write XXXXh Same register layout as CMB0. CMB6 8-word 0E F060h– 0E F06Fh Read/Write XXXXh Same register layout as CMB0. Register Name Size Address Access Type Value After Reset Comments Obsolete

199 www.national.com CP3BT23 CMB7 8-word 0E F070h– 0E F07Fh Read/Write XXXXh Same register layout as CMB0. CMB8 8-word 0E F080h– 0E F08Fh Read/Write XXXXh Same register layout as CMB0. CMB9 8-word 0E F090h– 0E F09Fh Read/Write XXXXh Same register layout as CMB0. CMB10 8-word 0E F0A0h– 0E F0AFh Read/Write XXXXh Same register layout as CMB0. CMB11 8-word 0E F0B0h– 0E F0BFh Read/Write XXXXh Same register layout as CMB0. CMB12 8-word 0E F0C0h– 0E F0CFh Read/Write XXXXh Same register layout as CMB0. CMB13 8-word 0E F0D0h– 0E F0DFh Read/Write XXXXh Same register layout as CMB0. CMB14 8-word 0E F0E0h– 0E F0EFh Read/Write XXXXh Same register layout as CMB0. CAN0 Registers CGCR0 Word 0E F100h Read/Write 0000h CTIM0 Word 0E F102h Read/Write 0000h GMSKX0 Word 0E F104h Read/Write 0000h GMSKB0 Word 0E F106h Read/Write 0000h BMSKX0 Word 0E F108h Read/Write 0000h BMSKB0 Word 0E F10Ah Read/Write 0000h CIEN0 Word 0E F10Ch Read/Write 0000h CIPND0 Word 0E F10Eh Read Only 0000h CICLR0 Word 0E F110h Write Only 0000h CICEN0 Word 0E F112h Read/Write 0000h CSTPND0 Word 0E F114h Read Only 0000h CANEC0 Word 0E F116h Read Only 0000h CEDIAG0 Word 0E F118h Read Only 0000h CTMR0 Word 0E F11Ah Read Only 0000h Register Name Size Address Access Type Value After Reset Comments Obsolete

www.national.com 200 CP3BT23 CAN1 Module Message Buffers CMB0_CNSTAT Word 0E F200h Read/Write XXXXh CMB0_TSTP Word 0E F202h Read/Write XXXXh CMB0_DATA3 Word 0E F204h Read/Write XXXXh CMB0_DATA2 Word 0E F206h Read/Write XXXXh CMB0_DATA1Word 0E F208h Read/Write XXXXh CMB0_DATA0 Word 0E F20Ah Read/Write XXXXh CMB0_ID0 Word 0E F20Ch Read/Write XXXXh CMB0_ID1Word 0E F20Eh Read/Write XXXXh CMB18-word 0E F210h– 0E F21Fh Read/Write XXXXh Same register layout as CMB0. CMB2 8-word 0E F220h– 0E F22Fh Read/Write XXXXh Same register layout as CMB0. CMB3 8-word 0E F230h– 0E F23Fh Read/Write XXXXh Same register layout as CMB0. CMB4 8-word 0E F240h– 0E F24Fh Read/Write XXXXh Same register layout as CMB0. CMB5 8-word 0E F250h– 0E F25Fh Read/Write XXXXh Same register layout as CMB0. CMB6 8-word 0E F260h– 0E F26Fh Read/Write XXXXh Same register layout as CMB0. CMB7 8-word 0E F270h– 0E F27Fh Read/Write XXXXh Same register layout as CMB0. CMB8 8-word 0E F280h– 0E F28Fh Read/Write XXXXh Same register layout as CMB0. CMB9 8-word 0E F290h– 0E F29Fh Read/Write XXXXh Same register layout as CMB0. CMB10 8-word 0E F2A0h– 0E F2AFh Read/Write XXXXh Same register layout as CMB0. CMB11 8-word 0E F2B0h– 0E F2BFh Read/Write XXXXh Same register layout as CMB0. CMB12 8-word 0E F2C0h– 0E F2CFh Read/Write XXXXh Same register layout as CMB0. CMB13 8-word 0E F2D0h– 0E F2DFh Read/Write XXXXh Same register layout as CMB0. CMB14 8-word 0E F2E0h– 0E F2EFh Read/Write XXXXh Same register layout as CMB0. Register Name Size Address Access Type Value After Reset Comments Obsolete

201 www.national.com CP3BT23 CAN1 Registers CGCR1Word 0E F300h Read/Write 0000h CTIM1Word 0E F302h Read/Write 0000h GMSKX1Word 0E F304h Read/Write 0000h GMSKB1Word 0E F306h Read/Write 0000h BMSKX1Word 0E F308h Read/Write 0000h BMSKB1Word 0E F30Ah Read/Write 0000h CIEN1Word 0E F30Ch Read/Write 0000h CIPND1Word 0E F30Eh Read Only 0000h CICLR1Word 0E F31 0h Write Only 0000h CICEN1Word 0E F31 2h Read/Write 0000h CSTPND1Word 0E F31 4h Read Only 0000h CANEC1Word 0E F31 6h Read Only 0000h CEDIAG1Word 0E F31 8h Read Only 0000h CTMR1Word 0E F31 Ah Read Only 0000h DMA Controller ADCA0 Double Word FF F800h Read/Write 0000 0000h ADRA0 Double Word FF F804h Read/Write 0000 0000h ADCB0 Double Word FF F808h Read/Write 0000 0000h ADRB0 Double Word FF F80Ch Read/Write 0000 0000h BLTC0 Word FF F810h Read/Write 0000h BLTR0 Word FF F814h Read/Write 0000h DMACNTL0 Word FF F81Ch Read/Write 0000h DMASTAT0 Byte FF F81Eh Read/Write 00h ADCA1 Double Word FF F820h Read/Write 0000 0000h ADRA1 Double Word FF F824h Read/Write 0000 0000h ADCB1 Double Word FF F828h Read/Write 0000 0000h ADRB1 Double Word FF F82Ch Read/Write 0000 0000h Register Name Size Address Access Type Value After Reset Comments Obsolete

www.national.com 202 CP3BT23BLTC1 Word FF F830h Read/Write 0000h BLTR1 Word FF F834h Read/Write 0000h DMACNTL1Word FF F83Ch Read/Write 0000h DMASTAT1Byte FF F83Eh Read/Write 00h ADCA2 Double Word FF F840h Read/Write 0000 0000h ADRA2 Double Word FF F844h Read/Write 0000 0000h ADCB2 Double Word FF F848h Read/Write 0000 0000h ADRB2 Double Word FF F84Ch Read/Write 0000 0000h BLTC2 Word FF F850h Read/Write 0000h BLTR2 Word FF F854h Read/Write 0000h DMACNTL2 Word FF F85Ch Read/Write 0000h DMASTAT2 Byte FF F85Eh Read/Write 00h ADCA3 Double Word FF F860h Read/Write 0000 0000h ADRA3 Double Word FF F864h Read/Write 0000 0000h ADCB3 Double Word FF F868h Read/Write 0000 0000h ADRB3 Double Word FF F86Ch Read/Write 0000 0000h BLTC3 Word FF F870h Read/Write 0000h BLTR3 Word FF F874h Read/Write 0000h DMACNTL3 Word FF F87Ch Read/Write 0000h DMASTAT3 Byte FF F87Eh Read/Write 00h Bus Interface Unit BCFG Byte FF F900h Read/Write 07h IOCFG Word FF F902h Read/Write 069Fh SZCFG0 Word FF F904h Read/Write 069Fh SZCFG1Word FF F906h Read/Write 069Fh SZCFG2 Word FF F908h Read/Write 069Fh Register Name Size Address Access Type Value After Reset Comments Obsolete

203 www.national.com CP3BT23 System Configuration MCFG Byte FF F910h Read/Write 00h DBGCFG Byte FF F912h Read/Write 00h MSTAT Byte FF F914h Read Only ENV2:0 pins SWRESET Byte FF F918h Write Only N/A Flash Program Memory Interface FMIBAR Word FF F940h Read/Write 0000h FMIBDR Word FF F942h Read/Write 0000h FM0WER Word FF F944h Read/Write 0000h FM1WER Word FF F946h Read/Write 0000h FMCTRL Word FF F94Ch Read/Write 0000h FMSTAT Word FF F94Eh Read/Write 0000h FMPSR Byte FF F950h Read/Write 04h FMSTART Byte FF F952h Read/Write 18h FMTRAN Byte FF F954h Read/Write 30h FMPROG Byte FF F956h Read/Write 16h FMPERASE Byte FF F958h Read/Write 04h FMMERASE0 Byte FF F95Ah Read/Write EAh FMEND Byte FF F95Eh Read/Write 18h FMMEND Byte FF F960h Read/Write 3Ch FMRCV Byte FF F962h Read/Write 04h FMAR0 Word FF F964h Read Only FMAR1Word FF F966h Read Only FMAR2 Word FF F968h Read Only Flash Data Memory Interface FSMIBAR Word FF F740h Read/Write 0000h FSMIBDR Word FF F742h Read/Write 0000h FSM0WER Word FF F744h Read/Write 0000h FSMCTRL Word FF F74Ch Read/Write 0000h FSMSTAT Word FF F74Eh Read/Write 0000h FSMPSR Byte FF F750h Read/Write 04h FSMSTART Byte FF F752h Read/Write 18h Register Name Size Address Access Type Value After Reset Comments Obsolete

www.national.com 204 CP3BT23FSMTRAN Byte FF F754h Read/Write 30h FSMPROG Byte FF F756h Read/Write 16h FSMPERASE Byte FF F758h Read/Write 04h FSMMERASE0 Byte FF F75Ah Read/Write EAh FSMEND Byte FF F75Eh Read/Write 18h FSMMEND Byte FF F760h Read/Write 3Ch FSMRCV Byte FF F762h Read/Write 04h FSMAR0 Word FF F764h Read Only FSMAR1Word FF F766h Read Only FSMAR2 Word FF F768h Read Only CVSD/PCM Converter CVSDIN Word FF FC20h Write Only 0000h CVSDOUT Word FF FC22h Read Only 0000h PCMIN Word FF FC24h Write Only 0000h PCMOUT Word FF FC26h Read Only 0000h LOGIN Byte FF FC28h Write Only 0000h LOGOUT Byte FF FC2Ah Read Only 0000h LINEARIN Word FF FC2Ch Write Only 0000h LINEAROUT Word FF FC2Eh Read Only 0000h CVCTRL Word FF FC30h Read/Write 0000h CVSTAT Word FF FC32h Read Only 0000h CVTEST Word FF FC34h Read/Write 0000h CVRADD Word FF FC36h Read/Write 0000h CVRDAT Word FF FC38h Read/Write 0000h CVDECOUT Word FF FC3Ah Read Only 0000h CVENCIN Word FF FC3Ch Read Only 0000h CVENCPR Word FF FC3Eh Read Only 0000h Triple Clock + Reset CRCTRL Byte FF FC40h Read/Write 00X0 0110b PRSFC Byte FF FC42h Read/Write 4Fh PRSSC Byte FF FC44h Read/Write B6h PRSAC Byte FF FC46h Read/Write FFh Register Name Size Address Access Type Value After Reset Comments Obsolete

205 www.national.com CP3BT23 Power Management PMMCR Byte FF FC60h Read/Write 00h PMMSR Byte FF FC62h Read/Write 0000 0XXXb Multi-Input Wake-Up 0 WK0EDG Word FF FC80h Read/Write 00h WK0ENA Word FF FC82h Read/Write 00h WK0ICTL1Word FF FC84h Read/Write 00h WK0ICTL2 Word FF FC86h Read/Write 00h WK0PND Word FF FC88h Read/Write 00h Bits may only be set; writing 0 has no effect. WK0PCL Word FF FC8Ah Write Only XXh WK0IENA Word FF FC8Ch Read/Write 00h Multi-Input Wake-Up 1 WK1EDG Word FF FCA0h Read/Write 00h WK1ENA Word FF FCA2h Read/Write 00h WK1ICTL1 Word FF FCA4h Read/Write 00h WK1ICTL2 Word FF FCA6h Read/Write 00h WK1PND Word FF FCA8h Read/Write 00h Bits may only be set; writing 0 has no effect. WK1PCL Word FF FCAAh Write Only XXh WK1IENA Word FF FCACh Read/Write 00h General-Purpose I/O Ports PBALT Byte FF FB00h Read/Write 00h PBDIR Byte FF FB02h Read/Write 00h PBDIN Byte FF FB04h Read Only XXh PBDOUT Byte FF FB06h Read/Write XXh PBWPU Byte FF FB08h Read/Write 00h PBHDRV Byte FF FB0Ah Read/Write 00h PBALTS Byte FF FB0Ch Read/Write 00h PCALT Byte FF FB10h Read/Write 00h Register Name Size Address Access Type Value After Reset Comments Obsolete

www.national.com 206 CP3BT23PCDIR Byte FF FB12h Read Only 00h PCDIN Byte FF FB14h Read/Write XXh PCDOUT Byte FF FB16h Read/Write XXh PCWPU Byte FF FB18h Read/Write 00h PCHDRV Byte FF FB1Ah Read/Write 00h PCALTS Byte FF FB1Ch Read/Write 00h PEALT Byte FF FCC0h Read/Write 00h PEDIR Byte FF FCC2h Read/Write 00h PEDIN Byte FF FCC4h Read Only XXh PEDOUT Byte FF FCC6h Read/Write XXh PEWPU Byte FF FCC8h Read/Write 00h PEHDRV Byte FF FCCAh Read/Write 00h PEALTS Byte FF FCCCh Read/Write 00h PFALT Byte FF FCE0h Read/Write 00h PFDIR Byte FF FCE2h Read/Write 00h PFDIN Byte FF FCE4h Read Only XXh PFDOUT Byte FF FCE6h Read/Write XXh PFWPU Byte FF FCE8h Read/Write 00h PFHDRV Byte FF FCEAh Read/Write 00h PFALTS Byte FF FCECh Read/Write 00h PGALT Byte FF F300h Read/Write 00h PGDIR Byte FF F302h Read/Write 00h PGDIN Byte FF F304h Read Only XXh PGDOUT Byte FF F306h Read/Write XXh PGWPU Byte FF F308h Read/Write 00h PGHDRV Byte FF F30Ah Read/Write 00h PGALTS Byte FF F30Ch Read/Write 00h PHALT Byte FF F320h Read/Write 00h PHDIR Byte FF F322h Read/Write 00h PHDIN Byte FF F324h Read Only XXh PHDOUT Byte FF F326h Read/Write XXh PHWPU Byte FF F328h Read/Write 00h PHHDRV Byte FF F32Ah Read/Write 00h PHALTS Byte FF F32Ch Read/Write 00h PJALT Byte FF F340h Read/Write 00h PJDIR Byte FF F342h Read/Write 00h Register Name Size Address Access Type Value After Reset Comments Obsolete

207 www.national.com CP3BT23 PJDIN Byte FF F344h Read Only XXh PJDOUT Byte FF F346h Read/Write XXh PJWPU Byte FF F348h Read/Write 00h PJHDRV Byte FF F34Ah Read/Write 00h PJALTS Byte FF F34Ch Read/Write 00h Advanced Audio Interface ARFR Word FF FD40h Read Only 0000h ARDR0 Word FF FD42h Read Only 0000h ARDR1Word FF FD44h Read Only 0000h ARDR2 Word FF FD46h Read Only 0000h ARDR3 Word FF FD48h Read Only 0000h ATFR Word FF FD4Ah Write Only XXXXh ATDR0 Word FF FD4Ch Write Only 0000h ATDR1Word FF FD4Eh Write Only 0000h ATDR2 Word FF FD50h Write Only 0000h ATDR3 Word FF FD52h Write Only 0000h AGCR Word FF FD54h Read/Write 0000h AISCR Word FF FD56h Read/Write 0000h ARSCR Word FF FD58h Read/Write 0004h ATSCR Word FF FD5Ah Read/Write F003h ACCR Word FF FD5Ch Read/Write 0000h ADMACR Word FF FD5Eh Read/Write 0000h Interrupt Control Unit IVCT Byte FF FE00h Read Only 10h Fixed Addr. NMISTAT Byte FF FE02h Read Only 00h EXNMI Byte FF FE04h Read/Write XXXX 00X0b IST AT0 Word FF FE0Ah Read Only 0000h IST AT1Word FF FE0Ch Read Only 0000h IST AT2 Word FF FE20h Read Only 0000h IENAM0 Word FF FE0Eh Read/Write FFFFh IENAM1Word FF FE1 0h Read/Write FFFFh IENAM2 Word FF FE22h Read/Write FFFFh Register Name Size Address Access Type Value After Reset Comments Obsolete

www.national.com 208 CP3BT23 Microwire/SPI Interface MWDAT Word FF F3A0h Read/Write XXXXh MWCTL1Word FF F3A2h Read/Write 0000h MWSTAT Word FF F3A4h Read Only All imple- mented bits are 0 UART0 U0TBUF Byte FF F200h Read/Write XXh U0RBUF Byte FF F202h Read Only XXh U0ICTRL Byte FF F204h Read/Write 01h Bits 0:1 read only U0STAT Byte FF F206h Read only 00h U0FRS Byte FF F208h Read/Write 00h U0MDSL1Byte FF F20Ah Read/Write 00h U0BAUD Byte FF F20Ch Read/Write 00h U0PSR Byte FF F20Eh Read/Write 00h U0OVR Byte FF F210h Read/Write 00h U0MDSL2 Byte FF F212h Read/Write 00h U0SPOS Byte FF F214h Read/Write 06h UART1 U1TBUF Byte FF F220h Read/Write XXh U1RBUF Byte FF F222h Read Only XXh U1ICTRL Byte FF F224h Read/Write 01h Bits 0:1 read only U1STAT Byte FF F226h Read only 00h U1FRS Byte FF F228h Read/Write 00h U1MDSL1 Byte FF F22Ah Read/Write 00h U1BAUD Byte FF F22Ch Read/Write 00h U1PSR Byte FF F22Eh Read/Write 00h U1OVR Byte FF F230h Read/Write 00h U1MDSL2 Byte FF F232h Read/Write 00h U1SPOS Byte FF F234h Read/Write 06h Register Name Size Address Access Type Value After Reset Comments Obsolete

209 www.national.com CP3BT23 UART2 U2TBUF Byte FF F240h Read/Write XXh U2RBUF Byte FF F242h Read Only XXh U2ICTRL Byte FF F244h Read/Write 01h Bits 0:1 read only U2STAT Byte FF F246h Read only 00h U2FRS Byte FF F248h Read/Write 00h U2MDSL1Byte FF F24Ah Read/Write 00h U2BAUD Byte FF F24Ch Read/Write 00h U2PSR Byte FF F24Eh Read/Write 00h U2OVR Byte FF F250h Read/Write 00h U2MDSL2 Byte FF F252h Read/Write 00h U2SPOS Byte FF F254h Read/Write 06h UART3 U3TBUF Byte FF F260h Read/Write XXh U3RBUF Byte FF F262h Read Only XXh U3ICTRL Byte FF F264h Read/Write 01h Bits 0:1 read only U3STAT Byte FF F266h Read only 00h U3FRS Byte FF F268h Read/Write 00h U3MDSL1Byte FF F26Ah Read/Write 00h U3BAUD Byte FF F26Ch Read/Write 00h U3PSR Byte FF F26Eh Read/Write 00h U3OVR Byte FF F270h Read/Write 00h U3MDSL2 Byte FF F272h Read/Write 00h U3SPOS Byte FF F274h Read/Write 06h Register Name Size Address Access Type Value After Reset Comments Obsolete

www.national.com 210 CP3BT23 ACCESS.bus ACBSDA Byte FF F2A0h Read/Write XXh ACBST Byte FF F2A2h Read/Write 00h ACBCST Byte FF F2A4h Read/Write 00h ACBCTL1Byte FF F2A6h Read/Write 00h ACBADDR Byte FF F2A8h Read/Write XXh ACBCTL2 Byte FF F2AAh Read/Write 00h ACBADDR2 Byte FF F2ACh Read/Write XXh ACBCTL3 Byte FF F2AEh Read/Write 00h Timing and Watchdog TWCFG Byte FF FF20h Read/Write 00h TWCP Byte FF FF22h Read/Write 00h TWMT0 Word FF FF24h Read/Write FFFFh T0CSR Byte FF FF26h Read/Write 00h WDCNT Byte FF FF28h Write Only 0Fh WDSDM Byte FF FF2Ah Write Only 5Fh Multi-Function Timer TCNT1Word FF FF40h Read/Write XXh TCRA Word FF FF42h Read/Write XXh TCRB Word FF FF44h Read/Write XXh TCNT2 Word FF FF46h Read/Write XXh TPRSC Byte FF FF48h Read/Write 00h TCKC Byte FF FF4Ah Read/Write 00h TCTRL Byte FF FF4Ch Read/Write 00h TICTL Byte FF FF4Eh Read/Write 00h TICLR Byte FF FF50h Read/Write 00h Register Name Size Address Access Type Value After Reset Comments Obsolete

211 www.national.com CP3BT23 Versatile Timer Unit MODE Word FF FF80h Read/Write 0000h IO1CTL Word FF FF82h Read/Write 0000h IO2CTL Word FF FF84h Read/Write 0000h INTCTL Word FF FF86h Read/Write 0000h INTPND Word FF FF88h Read/Write 0000h CLK1PS Word FF FF8Ah Read/Write 0000h COUNT1Word FF FF8Ch Read/Write 0000h PERCAP1Word FF FF8Eh Read/Write 0000h DTYCAP1Word FF FF90h Read/Write 0000h COUNT2 Word FF FF92h Read/Write 0000h PERCAP2 Word FF FF94h Read/Write 0000h DTYCAP2 Word FF FF96h Read/Write 0000h CLK2PS Word FF FF98h Read/Write 0000h COUNT3 Word FF FF9Ah Read/Write 0000h PERCAP3 Word FF FF9Ch Read/Write 0000h DTYCAP3 Word FF FF9Eh Read/Write 0000h COUNT4 Word FF FFA0h Read/Write 0000h PERCAP4 Word FF FFA2h Read/Write 0000h DTYCAP4 Word FF FFA4h Read/Write 0000h ADC ADCGCR Word FF F3C0h Read/Write 0000h ADCACR Word FF F3C2h Read/Write 0000h ADCCNTRL Word FF F3C4h Read/Write 0000h ADCSTART Word FF F3C6h Write Only N/A ADCSCDL Y Word FF F3C8h Read/Write 0000h ADCRESLT Word FF F3CAh Read Only 0000h ADCSMBC0 Word FF F3CEh Read/Write 1483h ADCSMBC1Word FF F3D0h Read/Write 24E6h ADCSMBC2 Word FF F3D2h Read/Write 2508h ADCSMBC3 Word FF F3D4h Read/Write 314Ah ADCSMSH Word FF F3D6h Read/Write 01A2h Register Name Size Address Access Type Value After Reset Comments Obsolete

www.national.com 212 CP3BT23 RNG RNGCST Word FF F280h Read/Write 0000h RNGD Word FF F282h Read/Write 0000h RNGDIVH Word FF F284h Read/Write 0000h RNGDIVL Word FF F286h Read/Write 0000h Register Name Size Address Access Type Value After Reset Comments Obsolete

213 www.national.com CP3BT23

28.0 Register Bit Fields

The following tables show the functions of the bit fields of the device registers. For more information on using these regis- ters, see the detailed description of the applicable function elsewhere in this data sheet. Bluetooth LLC Registers 7654321 0 PLN Reserved PLN[2:0] WHITENING_ CHANNEL_ SELECTION Reserved CHANNEL_ SELECTION[1:0] WHITENING SINGLE_FREQUENCY _SELECTION Reserved SINGLE_FREQUENCY_SEL[6:0] LN_BT_CLOCK_0 LN_BT_CLOCK[7:0] LN_BT_CLOCK_1LN_BT_CLOCK[1 5:8] LN_BT_CLOCK_2 LN_BT_CLOCK[23:16] LN_BT_CLOCK_3 Reserved LN_BT_CLOCK[27:23] RX_CN Reserved RX_CN[6:0] TX_CN Reserved TX_CN[6:0] AC_ACCEPTLVL[7:0] AC_ACCEPTLVL[7:0] AC_ACCEPTLVL[15:8] Reserved CORRELATOR_DELAY AC_ACCEPTLVL[9:8] LAP_ACCEPTLVL Reserved LAP_ACCEPTLVL[5:0] RFSYNCH_DELAY Reserved RFSYNCH_DELAY[5:0] SPI_READ[7:0] SPI_READ[7:0] SPI_READ[15:8] SPI_READ[15:8] SPI_MODE_CONFIG Reserved SPI_CLK_CONF[1:0] SPI_LEN_ CONF SPI_DATA _CONF3 SPI_DATA _CONF2 SPI_DATA_ CONF1 M_COUNTER_0 M_COUNTER[7:0] M_COUNTER_1M_COUNTER[1 5:8] M_COUNTER_2 Reserved M_COUNTER[20:16] N_COUNTER_0 N_COUNTER[7:0] N_COUNTER_1Reserved N_COUNTER[9:8] BT_CLOCK_WR_0 BT_CLOCK_WR[7:0] BT_CLOCK_WR_1BT_CLOCK_WR[1 5:8] BT_CLOCK_WR_2 BT_CLOCK_WR[23:16] BT_CLOCK_WR_3 Reserved BT_CLOCK_WR[27:24] WTPTC_1SLOT[7:0] WTPTC_1SLOT[7:0] WTPTC_1SLOT[15:8] WTPTC_1SLOT[15:8] WTPTC_3SLOT[7:0] WTPTC_3SLOT[7:0] WTPTC_3SLOT[15:8] WTPTC_3SLOT[15:8] WTPTC_5SLOT[7:0] WTPTC_5SLOT[7:0] Obsolete

www.national.com 214 CP3BT23WTPTC_5SLOT[15:8] WTPTC_5SLOT[15:8] SEQ_RESET Reserved SEQ_RESET SEQ_CONTINUE Reserved SEQ_ CONTINUE RX_STA TUS Reserved HEC Error Header Error Correction AM_ ADDR Error Payload CRC Error Payload Error Correction Payload Length Error PACKET_ DONE CHIP_ID Reserved CHIP_ID INT_VECTOR INT_VECTOR[7:0] SYSTEM_CLK_EN Reserved CLK_EN3 CLK_EN2 INT_SEQ_ EN CLK_EN1 LINK_TIMER_WR_RD[7:0] LINKTIMER_WR_RD[7:0] LINK_TIMER_WR_RD[15:8] LINKTIMER_WR_RD[15:8] LINK_TIMER_SELECT Reserved LINKTIMER_SELECT LINK_TIMER_STATUS_ EXP_FLAG LINK_TIMER_STATUS_EXP_FLAG[7:0] LINK_TIMER_STATUS_ RD_WR_FLAG Reserved LINK_ TIMER _WRITE_ DONE LINK_ TIMER_ READ_ VALID LINK_TIMER_ADJUST_ PLUS LINKTIMER_ADJUST_PLUS[7:0] LINK_TIMER_ADJUST_ MINUS LINKTIMER_ADJUST_MINUS[7:0] SLOTTIMER_WR_RD Reserved SLOT_TIMER_WR_RD[5:0] Bluetooth LLC Registers 7654321 0 Obsolete

215 www.national.com CP3BT23 CAN Control/ Status 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 CGCRn Reserved EIT DIAG EN INTE RNAL LOOP BACK IGN ACK LO DD IR TST PEN BUFF LOCK CRX CTX CAN EN CTIMn PSC[6:0] SJW[1:0] TSEG1[3:0] TSEG2[2:0] GMSKBn GM[28:18] RTR IDE GM[17:15] GMSKXn GM[14:0] XRTR BMSKBn BM[28:18] RTR IDE BM[17:15] BMSKXn BM[14:0] XRTR CIENn EI EN IEN[14:0] CIPNDn EI PND IPND[14:0] CICLRn EI CLR ICLR[14:0] CICENn EI CEN ICEN[14:0] CSTPNDn Reserved NS[2:0] IRQ IST[3:0] CANECn REC[7:0] TEC[7:0] CEDIAGn Res. DRI VE MON CRC STU FF TXE EBID[5:0] EFID[3:0] CTMRn CTMR[15:0] CAN Memory Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 CMBn.ID1 XI28 ID10 XI27 ID9 XI26 ID8 XI25 ID7 XI24 ID6 XI23 ID5 XI22 ID4 XI21 ID3 XI20 ID2 XI19 ID1 XI18 ID0 SRR RTR IDE XI17 XI16 XI15 CMBn.ID0 XI14 XI13 XI12 XI11 XI10 XI9 XI8 XI7 XI6 XI5 XI4 XI3 XI2 XI1 XI0 RTR CMBn.DATA0 Data 1.7 Data 1.6 Data 1.5 Data 1.4 Data 1.3 Data 1.2 Data 1.1 Data 1.0 Data 2.7 Data 2.6 Data 2.5 Data 2.4 Data 2.3 Data 2.2 Data 2.1 Data 2.0 CMBn.DATA1 Data 3.7 Data 3.6 Data 3.5 Data 3.4 Data 3.3 Data 3.2 Data 3.1 Data 3.0 Data 4.7 Data 4.6 Data 4.5 Data 4.4 Data 4.3 Data 4.2 Data 4.1 Data 4.0 CMBn.DATA2 Data 5.7 Data 5.6 Data 5.5 Data 5.4 Data 5.3 Data 5.2 Data 5.1 Data 5.0 Data 6.7 Data 6.6 Data 6.5 Data 6.4 Data 6.3 Data 6.2 Data 6.1 Data 6.0 CMBn.DATA3 Data 7.7 Data 7.6 Data 7.5 Data 7.4 Data 7.3 Data 7.2 Data 7.1 Data 7.0 Data 8.7 Data 8.6 Data 8.5 Data 8.4 Data 8.3 Data 8.2 Data 8.1 Data 8.0 CMBn.TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP TSTP CMBn.CNTSTA T DLC3 DLC2 DLC1DLC0 Reserved PRI3 PRI2 PRI1 PRI0 ST3 ST2 ST1 ST0 Obsolete

www.national.com 216 CP3BT23 DMAC Registers2 0 . . 1 6 1 51 41 31 21 11 0 9 8 7 6 5 4 3 2 1 0 ADCA Device A Address Counter ADRA Device A Address ADCB Device B Address Counter ADRB Device B Address BLTC N/A Block Length Counter BLTR N/A Block Length DMACNTL N/A Res. INCB ADB INCA ADA SW RQ Res. OT DIR IND TCS EO VR ETC CH EN DMASTAT N/A Reserved VLD CH AC OVR TC System Configuration Registers 7 6 5 43210 MCFG Reserved MEM_IO_ SPEED MISC_IO_ SPEED Reserved SCLKOE MCLKOE PLLCLKOE EXIOE DBGCFG Reserved FREEZE ON MSTAT ISPRST WDRST Reserved DPGM BUSY PGMBUSY OENV2 OENV1OENV0 BIU Registers 15 12 11 10 9 8 7 6 5 4 3 2 1 0 BCFG Reserved EWR IOCFG Reserved IPST Res. BW Reserved HOLD WAIT SZCFG0 Reserved FRE IPRE IPST Res. BW WBR RBE HOLD WAIT SZCFG1Reserved FRE IPRE IPST Res. BW WBR RBE HOLD WAIT SZCFG2 Reserved FRE IPRE IPST Res. BW WBR RBE HOLD WAIT T B I R e g i s t e r 76543210 TMODE Reserved TSTEN ENMEM TMSEL Obsolete

217 www.national.com CP3BT23 Flash Program Memory Interface Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 FMIBAR Reserved IBA FMIBDR IBD FM0WER FM0WE FM1WER FM1WE FM2WER FM2WE FM3WER FM3WE FMCTRL Reserved MER PER PE IENP ROG DIS VRF Res. CWD LOW PRW FMSTAT Reserved DE RR FM FULL FM BUSY PERR EERR FMPSR Reserved FTDIV FMSTART Reserved FTSTART FMTRAN Reserved FTTRAN FMPROG Reserved FTPROG FMPERASE Reserved FTPER FMMERASE0 Reserved FTMER FMEND Reserved FTEND FMMEND Reserved FTMEND FMRCV Reserved FTRCV FMAR0 Reserved Res. FMAR1WRPROT RDPROT ISPE EMPTY BOOTAREA FMAR2 CADR15:0 Flash Data Memory Interface Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 FSMIBAR Reserved IBA FSMIBDR IBD FSM0WER FM0WE FSM1WER FM1WE FSM2WER FM2WE FSM3WER FM3WE Obsolete

www.national.com 218 CP3BT23 FSMCTRL Reserved MER PER PE IENP ROG DIS VRF Res. CWD LOW PRW FSMSTAT Reserved DE RR FM FULL FM BUSY PE RR EE RR FSMPSR Reserved FTDIV FSMSTART Reserved FTSTART FSMTRAN Reserved FTTRAN FSMPROG Reserved FTPROG FSMPERASE Reserved FTPER FSMMERASE0 Reserved FTMER FSMEND Reserved FTEND FSMMEND Reserved FTMEND FSMRCV Reserved FTRCV FSMAR0 Reserved Res. FSMAR1WRPROT RDPROT ISPE EMPTY BOOTAREA FSMAR2 CADR15:0 Flash Data Memory Interface Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 CVSD/PCM Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 CVSDIN CVSDIN CVSDOUT CVSDOUT PCMIN PCMIN PCMOUT PCMOUT LOGIN Reserved LOGIN LOGOUT Reserved LOGOUT LINEARIN LINEARIN LINEAROUT LINEAROUT CVCTRL Reserved PCM CO NV CVSD CONV DMA PI DMA PO DMA CI DMA CO CVS DER RINT CVS DINT PCM INT CLK EN CV EN CVSTAT Reserved CVOUTST CVINST CVF CVE PCM INT CVN F CV NE CVTEST Reserved TEST _VAL ENC _IN DEC _EN RT TB CVRADD Reserved CVRADD CVRDAT CVRDAT Obsolete

219 www.national.com CP3BT23 CVDECOUT CVDECOUT CVENCIN CVENCIN CVENCPR CVENCPRT CVSD/PCM Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 CLK3RES Registers 76543210 CRCTRL Reserved POR ACE2 ACE1PLLPWD FCLK SCLK PRSFC Reserved MODE FCDIV PRSSC SCDIV PRSAC ACDIV2 ACDIV1 P M M R e g i s t e r 76543210 PMMCR HCCH HCCM DHC DMC WBPSM HALT IDLE PSM PMMSR Reserved OHC OMC OLC MIWU16 Registers 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 WKEDG WKED WKENA WKEN WKICTL1WKINTR7 WKINTR6 WKINTR5 WKINTR4 WKINTR3 WKINTR2 WKINTR1 WKINTR0 WKICTL2 WKINTR15 WKINTR14 WKINTR13 WKINTR12 WKINTR11 WKINTR10 WKINTR9 WKINTR8 WKPND WKPD WKPCL WKCL WKIENA WKIEN G P I O R e g i s t e r s 76543210 PxALT Px Pins Alternate Function Enable PxDIR Px Port Direction PxDIN Px Port Output Data PxDOUT Px Port Input Data PxWPU Px Port Weak Pull-Up Enable PxHDRV Px Port High Drive Strength Enable PxALTS Px Pins Alternate Function Source Selection Obsolete

www.national.com 220 CP3BT23 AAI Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 ARSR ARSH ARSL ATSR ATSH ATSL ARFR ARFH ARFL ARDR0 ARDH ARDL ARDR1ARDH ARDL ARDR2 ARDH ARDL ARDR3 ARDH ARDL ATFR ATFH ATFL ATDR0 ATDH ATDL ATDR1ATDH ATDL ATDR2 ATDH ATDL ATDR3 ATDH ATDL AGCR CLK EN AAI EN IOM2 IFS FSL CTF CRF IEBC FSS IEFS SCS LPB DWL ASS AISCR Reserved TX EIC TX IC RX EIC RX IC TX EIP TX IP RX EIP RX IP TX EIE TX IE RX EIE RX IE ARSCR RXFWM RXDSA RXSA RXO RXE RXF RX AF ATSCR TXFWM TXDSA TXSA TXU TXF TXE TXAE ACCR BCPRS FCPRS CSS ADMACR Reserved ACO ACD TMD RMD IVCT Reserved 0 0 INTVECT[5:0] ISTAT0 IST(15:0) ISTAT1IST(31 :1 6) IENAM0 IENA(15:0) IENAM1IENA(31 :1 6) UART Registers 76543210 UnTBUF UnTBUF UnRBUF URBUF UnICTRL UEEI UERI UETI UEFCI UCTS UDCTS URBF UTBE Obsolete

221 www.national.com CP3BT23 UnSTAT Reserved UXMIP URB9 UBKD UERR UDOE UFE UPE UnFRS Reserved UPEN UPSEL UXB9 USTP UCHAR UnMDSL1URTS UFCE UERD UETD UCKS UBRK UATN UMOD UnBAUD UDIV7:0 UnPSR UPSC UDIV10:8 UnOVR Reserved UOVSR UnMDSL2 Reserved USMD UnSPOS Reserved USAMP UART Registers 76543210 MWSPI16 Registers 1 5 . . . 9876543210 MWDAT MWDAT MWCTL1SCDV SCIDL SCM EIW EIR EIO ECHO MOD MNS MWEN MWSTAT Reserved OVR RBF BSY A C B R e g i s t e r s 76543210 ACBSDA DATA ACBST SLVSTP SDAST BER NEGACK STASTR NMATCH MASTER XMIT ACBCST ARPMATCH MATCHAF TGSCL TSDA GMATCH MATCH BB BUSY ACBCTL1STASTRE NMINTE GCMEN ACK Reserved INTEN STOP START ACBADDR SAEN ADDR ACBCTL2 SCLFRQ[6:0] ENABLE ACBADDR2 SAEN ADDR ACBCTL3 Reserved ARPEN SCLFRQ[8:7] TWM Registers 15 . . . 8 7 6 5 4 3 2 1 0 TWCFG Reserved Reserved WDSDME WDCT0I LWDCNT LTWMT0 LTWCP LTWCFG TWCP Reserved Reserved MDIV TWMT0 PRESET T0CSR Reserved Reserved FRZT0E WDTLD T0INTE TC RST WDCNT Reserved PRESET WDSDM Reserved RSTDATA Obsolete

www.national.com 222 CP3BT23 MFT16 Registers 1 5 . . . 8 76543210 TCNT1TCNT1 TCRA TCRA TCRB TCRB TCNT2 TCNT2 TPRSC Reserved Reserved CLKPS TCKC Reserved Reserved C2CSEL C1CSEL TCTRL Reserved TEN TAOUT TBEN TAEN TBEDG TAEDG TMDSEL TICTL Reserved TDIEN TCIEN TBIEN TAIEN TDPND TCPND TBPND TAPND TICLR Reserved Reserved TDCLR TCCLR TBCLR TACLR VTU Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 MODE TMOD4 T8 RUN RUN TMOD3 T6 RUN RUN TMOD2 T4 RUN RUN TMOD1 T2 RUN RUN IO1CTL P4 POL C4EDG P3 POL C3EDG P2 POL C2EDG P1 POL C1EDG IO2CTL P7 POL C7EDG P6 POL C6EDG P5 POL C5EDG P5 POL C5EDG INTCTL I4DEN I4CEN I4BEN I4AEN I3DEN I3CEN I3BEN I3AEN I2DEN I2CEN I2BEN I2AEN I1DEN I1CEN I1BEN I1AEN INTPND I4DPD I4CPD I4BPD I4APD I3DPD I3CPD I3BPD I3APD I2DPD I2CPD I2BPD I2APD I1DPD I1CPD I1BPD I1APD CLK1PS C2PRSC C1PRSC COUNT1CNT1 PERCAP1PCAP1 DTYCAP1DCAP1 COUNT2 CNT2 PERCAP2 PCAP2 DTYCAP2 DCAP2 CLK2PS C4PRSC C3PRSC COUNT3 CNT3 PERCAP3 PCAP3 DTYCAP3 DCAP3 COUNT4 CNT4 PERCAP4 PCAP4 DTYCAP4 DCAP4 Obsolete

223 www.national.com CP3BT23 ADC Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 ADCGCR MUX- OUTEN INTEN Res. NREF_CFG PREF_CFG TOUCH_CFG MUX_CFG DIFF ADCIN CLKEN ADCACR CNVT TRG PRM Reserved CLKDIV CLK- SEL ADCCNTRL Reserved AUTO EXT POL ADCSTART Write any value. ADCSCDL Y ADC_DIV ADC_DELAY1ADC_DELAY2 ADCRESLT ADC_ DONE ADC_ OFLW PEN_ DOWN SIGN ADC_RESULT RNG Registers 1 5 1 4 1 3 1 2 1 1 1 0 9876543210 RNGCST Reserved IMSK Reserved DVALID RNGE RNGD RNGD RNGDIVH Reserved RNGDIV17:16 RNGDIVL RNGDIV15:0 Obsolete

www.national.com 224 CP3BT23

29.0 Electrical Characteristics

29.1 ABSOLUTE MAXIMUM RATINGS

If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distribu- tors for availability and specifications. Note: Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electri- cal specifications are not ensured when operating the de- vice at absolute maximum ratings. * The latch-up tolerance on Access Bus pins 14 and 15 exceeds 150mA.

29.2 DC ELECTRICAL CHARACTERISTICS (Temperature: -40°C ≤ TA ≤ +85°C)

Supply voltage (VCC) 3.6V All input and output voltages with re- spect to GND* -0.5V to IOVCC + 0.5V ESD protection level 2 kV (Human Body Model) Allowable sink/source current per signal pin ±10 mA T otal current into IOVCC pins 200 mA T otal current into VCC pins (source) 200 mA T otal current out of GND pins (sink) 200 mA Latch-up immunity ±200 mA Storage temperature range -65°C to +150°C Symbol Parameter Conditions Min Max Units Vcc Digital Logic Supply Voltage 2.25 2.75 V IOVcc I/O Supply Voltage 2.25 3.63 V AVcc Analog PLL Supply Voltage 2.25 2.75 V ADVcc ADC Supply Voltage 2.25 2.75 V VIL Logical 0 Input Voltage (except X1CKI, X2CKI, and RESET) -0.5 a 0.3 Vcc V VIH Logical 1 Input Voltage (except X1CKI, X2CKI, and RESET 0.7 IOVcc IOVcc + 0.5 a V Vxl1 X1CKI Logical 0 Input Voltage External X1 clock -0.5 a 0.3 Vcc V Vxh1 X1CKI Logical 1 Input Voltage External X1 clock 0.7 Vcc Vcc + 0.5 V Vxl2 X2CKI Logical 0 Input Voltage External X2 clock -0.5 a 0.6 V Vxh2 X2CKI Logical 1 Input Voltage External X2 clock 0.7 Vcc Vcc + 0.5 V Vrstl RESET Logical 0 Input Voltage RESET input -0.5 0.4 V Vrsth RESET Logical 1 Input Voltage RESET input 1.7 V Vhys Hysteresis Loop Width a 0.1 IOVcc V IOH Logical 1 Output Current VOH = 1.8V , IOVcc = 2.25V -6 mA IOL Logical 0 Output Current VOL = 0.45V, IOVcc = 2.25V 6m A IOLACB SDA, SCL Logical 0 Output Current VOL = 0.4V , IOVcc = 2.25V 3m A IOLTS Touchscreen Logical 0 Output Current b (for ADC2/TSX- and ADC3/TSY -) VOL = 0.15V, ADVcc = 2.25V 18m A IOHTS Touchscreen Logical 1 Output Current b (for ADC0/TSX+ and ADC1/TSY+) VOH = 2.1, ADVcc = 2.25V -18 mA IOHW Weak Pull-up Current VIL = 0V, IOVcc = 3.63V -20 -300 µA IL High Impedance Input Leakage Current c (except ADC0/TSX+, ADC1/TSY+, ADC2/TSX-, ADC3/TSY -) 0V ≤ Vin ≤ IOVcc -2.0 2.0 µA Obsolete

225 www.national.com CP3BT23

29.3 ADC ELECTRICAL CHARACTERISTICS (Temperature: -40°C ≤ TA ≤ +85°C)

IL High Impedance Input Leakage Current (for ADC0/TSX+, ADC1/TSY+, ADC2/TSX-, ADC3/TSY -) 0V ≤ Vin ≤ IOVcc -5.0 5.0 µA IO(Off) Output Leakage Current (I/O pins in input mode) 0V ≤ Vout ≤ Vcc -2.0 2.0 µA Icca1Digital Supply Current Active Mode d Vcc = 2.75V, IOVcc=3.63V 20 mA Iccprog Digital Supply Current Active Mode e Vcc = 2.75V, IOVcc = 3.63V 20 mA Iccps Digital Supply Current Power Save Mode f Vcc = 2.75V, IOVcc =3.63V 4m A Iccid Digital Supply Current Idle Mode g Vcc = 2.75V, IOVcc = 3.63V 2m A Iccq Digital Supply Current Halt Mode g,h Vcc = 2.75V, IOVcc = 3.63V, 20°C 150 µA a. Guaranteed by design b. Characterized not tested in production. c. Some pins not tested for leakage due to I/O structure. d. Run from internal memory (RAM), Iout = 0 mA, X1CKI = 12 MHz, PLL enabled (4×), internal system clock is

24 MHz, not programming Flash memory

e. Same conditions as Icca1, but programming or erasing Flash memory page f. Running from internal memory (RAM), Iout = 0 mA, XCKI1 = 12 MHz, PLL disabled, X2CKI = 32.768 kHz, device put in power-save mode, Slow Clock derived from XCKI1 g. Iout = 0 mA, XCKI1 = Vcc, X2CKI = 32.768 kHz h. Halt current approximately doubles for every 20°C. Symbol Parameter Conditions Min Typ Max Units V PREF ADC Positive Reference Input a a. Guaranteed by design 22 .75 V VNREF ADC Negative Reference Input a 00 .25 V ADC Input Range a VNREF VPREF V Clock Frequency 12 MHz tC Conversion Time (12-bit result) 14 µs INL Integral Non-Linearity ±2 LSB DNL Differential Non-Linearity ±0.7 LSB C ADCIN Total Capacitance of ADC Input a 92 0 pF C ADCINS Switched Capacitance of ADC Input a 810 pF R ADCIN Resistance of ADC Input Path a 0.11 2 kohm C ADCIN Total Capacitance of ADC Reference Input a 50 100 pF C ADCINS Switched Capacitance of ADC Reference Input a 810 pF R ADCIN Resistance of ADC Reference Input Path a 0.2 0.6 kohm Symbol Parameter Conditions Min Max Units Obsolete

www.national.com 226 CP3BT23

29.4 FLASH MEMORY ON-CHIP PROGRAMMING

(Guaranteed by design.) Symbol Parameter Conditions Min Max Units tSTART Program/Erase to NVSTR Setup Timea (NVSTR = Non-Volatile Storage 5- µ s tTRAN NVSTR to Program Setup Timeb 10- µ s tPROG Programming Pulse Widthc 20 40 µs tPERASE Page Erase Pulse Widthd 20 - ms tMERASE Module Erase Pulse Widthe 200 - ms tEND NVSTR Hold Timef 5- µ s tMEND NVSTR Hold Time (Module Erase)g 100 - µs tRCV Recovery Timeh 1-µ s tHV Cumulative Program High Voltage Period For Each Row After Erasei 128K program blocks - 8 ms tHV 8K data block - 4 ms Write/Erase Endurance 20,000 - cycles Data Retention 25°C 100 - years a. Program/erase to NVSTR Setup Time is determined by the following equation: tSTART = Tclk × (FTDIV + 1) × (FTSTART + 1), where Tclk is the System Clock period, FTDIV is the contents of the FMPSR or FSMPSR register, and FTSTART is the contents of the FMSTART or FSMST ART register b. NVSTR to Program Setup Time is determined by the following equation: tTRAN = Tclk × (FTDIV + 1) × (FTTRAN + 1), where Tclk is the System Clock period, FTDIV is the contents of the FMPSR or FSMPSR register, and FTTRAN is the contents of the FMTRAN or FSMTRAN register c. Programming Pulse Width is determined by the following equation: tPROG = Tclk × (FTDIV + 1) × 8 × (FTPROG + 1), where Tclk is the System Clock period, FTDIV is the con- tents of the FMPSR or FSMPSR register, and FTPROG is the contents of the FMPROG or FSMPROG regis- ter d. Page Erase Pulse Width is determined by the following equation: t PERASE = Tclk × (FTDIV + 1) × 4096 × (FTPER + 1), where Tclk is the System Clock period, FTDIV is the contents of the FMPSR or FSMPSR register, and FTPER is the contents of the FMPERASE or FSMPER- ASE register e. Module Erase Pulse Width is determined by the following equation: t MERASE = Tclk × (FTDIV + 1) × 4096 × (FTMER + 1), where Tclk is the System Clock period, FTDIV is the contents of the FMPSR or FSMPSR register, and FTMER is the contents of the FMMERASE0 or FSMMERASE0 register f. NVSTR Hold Time is determined by the following equation: tEND = Tclk × (FTDIV + 1) × (FTEND + 1), where Tclk is the System Clock period, FTDIV is the contents of the FMPSR or FSMPSR register, and FTEND is the contents of the FMEND or FSMEND register g. NVSTR Hold Time (Module Erase) is determined by the following equation: tMEND = Tclk × (FTDIV + 1) × 8 × (FTMEND + 1), where Tclk is the System Clock period, FTDIV is the con- tents of the FMPSR or FSMPSR register, and FTMEND is the contents of the FMMEND or FSMMEND regis- ter h. Recovery Time is determined by the following equation: t RCV = Tclk × (FTDIV + 1) × (FTRCV + 1), where Tclk is the System Clock period, FTDIV is the contents of the FMPSR or FSMPSR register, and FTRCV is the contents of the FMRCV or FSMRCV register i. Cumulative program high voltage period for each row after erase tHV is the accumulated duration a flash cell is exposed to the programming voltage after the last erase cycle. Obsolete

227 www.national.com CP3BT23

29.5 OUTPUT SIGNAL LEVELS

All output signals are powered by the digital supply (VCC). Table 76 summarizes the states of the output signals during the reset state (when VCC power exists in the reset state) and during the Power Save mode. The RESET and NMI input pins are active during the Power Save mode. In order to guarantee that the Power Save cur- rent not exceed 1 mA, these inputs must be driven to a volt- age lower than 0.5V or higher than VCC - 0.5V. An input voltage between 0.5V and (VCC - 0.5V) may result in power consumption exceeding 1 mA.

29.6 CLOCK AND RESET TIMING

(Guaranteed by design. All timing except memory interface characterized not tested for production.) Table 76 Output Pins During Reset and Power-Save Signals on a Pin Reset State (with Vcc) Power Save Mode Comments PB7:0 TRI-STATE Previous state I/O ports will maintain their values when entering power-save modePC7:0 TRI-STATE Previous state PE5:0 TRI-STATE Previous state PF7:0 TRI-STATE Previous state PG7:0 TRI-STATE Previous state PH7:0 TRI-STATE Previous state PJ7:0 TRI-STATE Previous state Table 77 Clock and Reset Signals Symbol Figure Description Reference Min (ns) Max (ns) Clock Input Signals tX1p 108 X1 period Rising Edge (RE) on X1 to next RE on X1 83.33 83.33 t X1h 108 X1 high time, external clock At 2V level (Both Edges) (0.5 Tclk) - 5 tX1l 108 X1 low time, external clock At 0.8V level (Both Edges) (0.5 Tclk) - 5 tX2p 108 X2 perioda a. Only when operating with an external square wave on X2CKI; otherwise a 32 kHz crystal network must be used between X2CKI and X2CKO. If Slow Clock is internally generated from Main Clock, it may not exceed this given limit. RE on X2 to next RE on X2 10,000 t X2h 108 X2 high time, external clock At 2V level (both edges) (0.5 Tclk) - 500 tX2l 108 X2 low time, external clock At 0.8V level (both edges) (0.5 Tclk) - 500 tIH 109 Input hold time (NMI, RXD1, RXD2) After RE on CLK 0 Reset and NMI Input Signals tIW 109 NMI Pulse Width NMI Falling Edge (FE) to RE 20 tRST 110 RESET Pulse Width RESET FE to RE 100 tR 110 Vcc Rise Time 0.1 Vcc to 0.9 Vcc Obsolete

Figure 108. Clock Timing Figure 109. NMI Signal Timing Figure 110. Non-Power-On Reset Figure 111. Power-On Reset

0.9 VCC

0.1 VCC

29.7 UART TIMING

Figure 112. UART Synchronous Mode Timing

29.8 I/O PORT TIMING

Figure 113. I/O Port Timing

29.9 ADVANCED AUDIO INTERFACE (AAI) TIMING

Figure 114. Receive Timing, Short Frame Sync

116 Receive Data Setup Time Before Falling Edge (FE)

116 Receive Data Hold Time After FE on SRCLK 20 -

116 Frame Sync Valid High RE on SRCLK/SCK to RE

116 Frame Sync Valid Low RE on SRCLK/SCK to FE

117 Transmit Data Valid RE on SCK to STD Valid - 20

233 www.national.com CP3BT23

29.10 MICROWIRE/SPI TIMING

Table 81 Microwire/SPI Signals Symbol Figure Description Reference Min (ns) Max (ns) Microwire/SPI Input Signals tMSKh 118 Microwire Clock High At 2.0V (both edges) 80 - tMSKl 118 Microwire Clock Low At 0.8V (both edges) 80 - tMSKp 118 Microwire Clock Period SCIDL bit = 0; Rising Edge (RE) MSK to next RE MSK 200

119 SCIDL bit = 1; Falling Edge

(FE) MSK to next FE MSK - tMSKh 118 MSK Hold (slave only) After MWCS goes inactive 40 - tMSKs 118 MSK Setup (slave only) Before MWCS goes active 80 - tMWCSh 118 MWCS Hold (slave only) SCIDL bit = 0: After FE MSK

119 SCIDL bit = 1: After RE

t MWCSs 118 MWCS Setup (slave only) SCIDL bit = 0: Before RE MSK

119 SCIDL bit = 1: Before FE

Microwire Data In Hold (master) Normal Mode: After RE MSK

120 Alternate Mode: After FE

Microwire Data In Hold (slave) Normal Mode: After RE MSK t MDIs 118 Microwire Data In Setup Normal Mode: Before RE MSK

120 Alternate Mode: Before FE

Microwire/SPI Output Signals tMSKh 118 Microwire Clock High At 2.0V (both edges) 40 - tMSKl 118 Microwire Clock Low At 0.8V (both edges) 40 - tMSKp 118 Microwire Clock Period SCIDL bit = 0: Rising Edge (RE) MSK to next RE MSK 100

119 SCIDL bit = 1: Falling Edge

(FE) MSK to next FE MSK - t MSKd 118 MSK Leading Edge Delayed (master only) Data Out Bit #7 Valid 0.5 tMSK 1.5 tMSK tMDOf 118 Microwire Data Float b (slave only) After RE on MWCS -2 5 tMDOh 118 Microwire Data Out Hold Normal Mode: After FE MSK 0.0

119 Alternate Mode: After RE

tMDOnf 122 Microwire Data No Float (slave only) After FE on MWCS 02 5 Obsolete

Figure 118. Microwire Transaction Timing, Normal Mode, SCIDL = 0

Figure 119. Microwire Transaction Timing, Normal Mode, SCIDL = 1

Figure 120. Microwire Transaction Timing, Alternate Mode, SCIDL = 0

www.national.com 238 CP3BT23 29.11 ACCESS.BUS TIMING Table 82 ACCESS.bus Signals Symbol Figure Description Reference Min (ns) Max (ns) ACCESS.bus Input Signals tBUFi 124 Bus free time between Stop and Start Condition tSCLhigho - tCSTOsi 124 SCL setup time Before Stop Condition (8 × tCLK ) - tSCLri - tCSTRhi 124 SCL hold time After Start Condition (8 × tCLK ) - tSCLri - tCSTRsi 124 SCL setup time Before Start Condition (8 × tCLK ) - tSCLri - tDHCsi 125 Data High setup time Before SCL Rising Edge (RE) 2 × tCLK - tDLCsi 124 Data Low setup time Before SCL RE 2 × tCLK - tSCLfi 123 SCL signal rise time - 300 tSCLri 123 SCL signal fall time - 1000 tSCLlowi 126 SCL low time After SCL Falling Edge (FE) 16 × t CLK - tSCLhighi 126 SCL high time After SCL RE 16 × tCLK - tSDAri 123 SDA signal rise time - 1000 tSDAfl 123 SDA signal fall time - 300 tSDAhi 126 SDA hold time After SCL FE 0 - tSDAsi 126 SDA setup time Before SCL RE 2 × tCLK - ACCESS.bus Output Signals tBUFo 124 Bus free time between Stop and Start Condition t SCLhigho - tCSTOso 124 SCL setup time Before Stop Condition tSCLhigho - tCSTRho 124 SCL hold time After Start Condition tSCLhigho - tCSTRso 125 SCL setup time Before Start Condition tSCLhigho - tDHCso 125 Data High setup time Before SCL R.E. t SCLhigho -tSDAro - tDLCso 124 Data Low setup time Before SCL R.E. t SCLhigho -tSDAfo - tSCLfo 123 SCL signal Fall time - 300c tSCLro 123 SCL signal Rise time - - d tSCLlowo 126 SCL low time After SCL F .E. (K × tCLK ) -1e - tSCLhigho 126 SCL high time After SCL R.E. (K × tCLK ) -1e - tSDAfo 123 SDA signal Fall time - 300 tSDAro 123 SDA signal Rise time -- tSDAho 126 SDA hold time After SCL F .E. (7 × tCLK ) - tSCLfo - tSDAvo 126 SDA valid time After SCL F .E. (7 × tCLK ) + tRD Obsolete

Figure 126. ACB Data Timing and "i" for input signal timing. unless the parameter already includes the suffix.

29.12 MULTI-FUNCTION TIMER (MFT) TIMING

Figure 127. Multi-Function Timer Input Timing

29.13 VERSATILE TIMING UNIT (VTU) TIMING

Figure 128. Versatile Timing Unit Input Timing

243 www.national.com CP3BT23

29.14 EXTERNAL BUS TIMING

Table 85 External Bus Signals Symbol Figure Description Reference Min (ns) Max (ns) External Bus Input Signals 129, 131, 132, 133 Input Setup Time D[15:0] Before Rising Edge (RE) on CLK 8- t 129, 131, 132, 133 Output Hold Time D[15:0] After RE on CLK 0 - External Bus Output Signals t 129, 130 Output Valid Time D[15:0] After RE on CLK - 8 129, 130, 131, 132, 133 Output Valid Time A[22:0] After RE on CLK - 8 t 129, 130, 131, 132, 133 Output Active/Inactive Time RD SEL[1:0] SELIO After RE on CLK - 8 129, 130 Output Active/Inactive Time WR[1:0] After RE on CLK - 0.5 Tclk + 8 t7 131 Minimum Inactive Time RD At 2.0V Tclk - 4 - t8 129 Output Float Time D[15:0] After RE on CLK - 8 t9 129 Minimum Delay Time From RD Trailing Edge (TE) to D[15:0] driven Tclk - 4 - t10 129,

130 Minimum Delay Time From RD TE to SELn

Leading Edge (LE) 0- t11 130 Minimum Delay Time From SELx TE to SELy LE 0 - t12 129, 130, 131, 132, 133 Output Hold Time A[22:0] D[15:0] RD SEL[2:0] SELIO After RE on CLK 0 - t13 129, 130 Output Hold Time WR[1:0] After RE on CLK 0.5 Tclk - 3 - Obsolete

Figure 129. Early Write Between Normal Read Cycles (No Wait States)

Figure 130. Late Write Between Normal Read Cycles (No Wait States)

Figure 131. Consecutive Normal Read Cycles (Burst, No Wait States)

Figure 132. Normal Read Cycle (Wait Cycle Followed by Hold Cycle)

Figure 133. Early Write Between Fast Read Cycles

30.0 Pin Assignments

30.1 LQFP-128 PACKAGE

mensions are provided in Section 32.0. Figure 134. CP3BT23 in the LQFP-128 Package (Top View)

www.national.com 250 CP3BT23 AVCC 29 PWR ADGND 90 PWR ADVCC 89 PWR X2CKI 30 I X2CKO 31O ENV2 SLOWCLK 34 I/O ENV1CPUCLK 35 I/O ENV0 PLLCLK 36 I/O RESET 100 I TMS 101 I TDI 102 I TCK 103 I TDO 106 O RDY 108 O RFDATA 68 I/O SCL 81I/O SDA 82 I/O ADC0 TSX+ 92 I/O/HIZ 20mA+ ADC1TSY+ 93 I/O/HIZ 20mA+ ADC2 TSX- 94 I/O/HIZ 20mA+ ADC3 TSY - 95 I/O/HIZ 20mA+ ADC4 MUXOUT0 96 I/O ADC5 MUXOUT197 I/O ADC6 98 I ADC7 ADCIN 99 I VREFP 91I PB0 D0 23 GPIO PB1D1 22 GPIO PB2 D2 20 GPIO PB3 D3 19 GPIO PB4 D4 18 GPIO PB5 D5 16 GPIO PB6 D6 15 GPIO PB7 D7 14 GPIO PC0 D8 12 GPIO PC1D9 11 GPIO PC2 D10 9 GPIO PC3 D11 8 GPIO PC4 D12 6 GPIO PC5 D13 5 GPIO PC6 D14 3 GPIO PC7 D15 2 GPIO PE0 RXD0 87 GPIO Table 86 Pin Assignments for LQFP-128 Package Pin Name Alternate Function(s) Pin Numbers Type Obsolete

251 www.national.com CP3BT23 PE1TXD0 83 GPIO PE2 RTS 86 GPIO PE3 CTS 88 GPIO PE4 CKX/TB 40 GPIO PE5 SRFS/NMI 120 GPIO PE6 CAN1RX 61 I/O PE7 CAN1TX 62 I/O PF0 MSK/TIO1 111 GPIO PF1 MDIDO/TIO2 114 GPIO PF2 MDODI/TIO3 116 GPIO PF3 MWCS/ TIO4 109 GPIO PF4 SCK/TIO5 122 GPIO PF5 SFS/TIO6 123 GPIO PF6 STD/TIO7 125 GPIO PF7 SRD/TIO8 126 GPIO PG0 RFSYNC 69 GPIO PG1RFCE 70 GPIO PG2 SRCLK 118 GPIO PG3 SCLK 71GPIO PG4 SDAT 72 GPIO PG5 SLE 73 GPIO PG6 WUI10 37 GPIO PG7 TA 41GPIO PH0 RXD1/WUI11 105 GPIO PH1 TXD1/WUI12 46 GPIO PH2 RXD2/WUI13 48 GPIO PH3 TXD2/WUI14 50 GPIO PH4 RXD3/WUI15 52 GPIO PH5 TXD3/WUI16 54 GPIO PH6 CAN0RX/WUI17 57 GPIO PH7 CAN0TX 59 GPIO PJ0 WUI18 128 GPIO PJ1WUI1 9 1 GPIO PJ2 WUI20 38 GPIO PJ3 WUI2139 GPIO PJ4 WUI22 64 GPIO PJ5 WUI23 65 GPIO PJ6 WUI24 66 GPIO PJ7 ASYNC/WUI9 104 GPIO Note 1: The ENV0, ENV1, ENV2, RESET, TCK, TDI, and TMS pins each have a weak pull-up to keep the input from floating. Note 2: These functions are always enabled, due to the direct low-impedance path to these pins. Table 86 Pin Assignments for LQFP-128 Package Pin Name Alternate Function(s) Pin Numbers Type Obsolete

30.2 LQFP-144 PACKAGE

mensions are provided in Section 32.0. Figure 135. CP3BT23 in the LQFP-144 Package (Top View)

253 www.national.com CP3BT23 Table 87 Pin Assignments for LQFP-144 Package Pin Name Alternate Function(s) Pin Number Type GND 23, 32, 59, 85, 91, 121 PWR VCC 24, 31, 58, 86, 90, 122 PWR IOGND 3, 9, 16, 43, 46, 50, 56, 67, 84, 117, 130 PWR IOVCC 6, 12, 20, 41, 44, 48, 52, 64, 72, 80, 126, 140 PWR AGND 27 PWR AVCC 28 PWR ADGND 96 PWR ADVCC 95 PWR X1CKI BBCLK 26 I X1CKO 25 O X2CKI 29 I X2CKO 30 O ENV2 SLOWCLK 33 I/O ENV1CPUCLK 34 I/O ENV0 PLLCLK 35 I/O RESET 106 I TMS 107 I TDI 108 I TCK 109 I TDO 112 O RDY 113O RFDATA 73 I/O SCL 87 I/O SDA 88 I/O ADC0 TSX+ 98 I/O/HIZ 20mA+ ADC1TSY+ 99 I/O/HIZ 20mA+ ADC2 TSX- 100 I/O/HIZ 20mA+ ADC3 TSY - 101 I/O/HIZ 20mA+ ADC4 MUXOUT0 102 I/O ADC5 MUXOUT11 03 I/O ADC6 104 I ADC7 ADCIN 105 I VREFP 97 I PB0 D0 22 GPIO PB1D1 21 GPIO PB2 D2 19 GPIO PB3 D3 18 GPIO PB4 D4 17 GPIO PB5 D5 15 GPIO PB6 D6 14 GPIO PB7 D7 13 GPIO Obsolete

www.national.com 254 CP3BT23 PC0 D8 11 GPIO PC1D9 10 GPIO PC2 D10 8 GPIO PC3 D11 7 GPIO PC4 D12 5 GPIO PC5 D13 4 GPIO PC6 D14 2 GPIO PC7 D15 1 GPIO PE0 RXD0 93 GPIO PE1TXD0 89 GPIO PE2 RTS 92 GPIO PE3 CTS 94 GPIO PE4 CKX/TB 37 GPIO PE5 SRFS/NMI 134 GPIO PE6 CAN1RX 70 GPIO PE7 CAN1TX 71 GPIO PF0 MSK/TIO11 20 GPIO PF1MDIDO/TIO2 123 GPIO PF2 MDODI/TIO3 127 GPIO PF3 MWCS/ TIO4 115 GPIO PF4 SCK/TIO5 135 GPIO PF5 SFS/TIO6 136 GPIO PF6 STD/TIO7 137 GPIO PF7 SRD/TIO8 138 GPIO PG0 RFSYNC 74 GPIO PG1RFCE 75 GPIO PG2 SRCLK 133 GPIO PG3 SCLK 76 GPIO PG4 SDAT 77 GPIO PG5 SLE 78 GPIO PG6 WUI10 36 GPIO PG7 TA 38 GPIO PH0 RXD1/WUI11 111 GPIO PH1 TXD1/WUI12 47 GPIO PH2 RXD2/WUI13 49 GPIO PH3 TXD2/WUI14 51 GPIO PH4 RXD3/WUI15 53 GPIO PH5 TXD3/WUI16 57 GPIO PH6 CAN0RX/WUI17 60 GPIO PH7 CAN0TX 65 GPIO PJ0 WUI18 144 GPIO PJ7 ASYNC 110 GPIO A22 63 O A2162 O Pin Name Alternate Function(s) Pin Number Type Obsolete

255 www.national.com CP3BT23 A20 61O A19 55 O A18 54 O A17 45 O A16 42 O A15 40 O A14 39 O A13 143 O A12 142 O A11 141 O A10 139 O A9 132 O A8 131 O A7 129 O A6 128 O A5 125 O A4 124 O A3 119 O A2 118 O A11 16 O A0 114 O SEL0 79 O SEL1 81O SEL2 82 O SELIO 83 O RD 66 O WR0 68 O WR1 69 O Note 1: The ENV0, ENV1, ENV2, RESET, TCK, TDI, and TMS pins each have a weak pull-up to keep the input from floating. Note 2: These functions are always enabled, due to the direct low-impedance path to these pins. Pin Name Alternate Function(s) Pin Number Type Obsolete

www.national.com 256 CP3BT23

31.0 Revision History

Date Major Changes From Previous Version 4/3/03 Original release. 5/26/03 Fixed maximum boot area in Section 8. Fixed names of clock signals in Figures 5 and 6. Fixed addresses of FSMARx registers in Register Map section. Added default value for RNGDIV. 6/16/03 Corrected Table 27. Changed I OH and IOL . 6/30/03 Changed NSIDs, deleted commercial temperature range device, changed ADC conversion time to 15 microseconds. 10/7/03 Updated DC electrical specifications. Added ADC electrical specifications. Added more detail to Table 7. Added Table 25. 11/14/03 Defined valid range of SCDV field in Microwire/SPI module. Noted default PRSSC register value generates a Slow Clock frequency slightly higher than 32768 Hz. Clarified usage of CVSTAT register bits and fields in CVSD/PCM module. Updated layout of Bluetooth LLC registers. Added usage hint for avoiding ACCESS.bus module bus error. Added usage hint for avoiding CAN unexpected loopback condition. 2/28/04 Changed NSID designations in the product selection guide. Updated Bluetooth section for LMX5251 and LMX5252 radio chips. Added BTSEQ[3:1] signals to pin descriptions, GPIO alternate functions, and package pin assignments. Added entry for CTIM register in CAN section register list. Changed CVSD Conversion section. Changed definition of the RESOLUTION field of the CVSD Control register (CVCTRL). Changed reset values for ADC registers. Added maximum I/O voltage in Absolute Maximum Ratings section. Added RESET Low minimum DC specification. Added Iccprog DC specification. Changed Vxl2 DC specification. 3/16/04 Changed LMX5251 interface circuit. Updated DC specifications for clock input low voltage, reset input high voltage, and halt current. 5/10/04 Corrected NSIDs for no-lead solder parts. 5/12/04 Moved revision history in front of physical dimensions. Changed back page disclaimers. 6/2/04 Changed AC and DC specifications. 6/15/04 Changed absolute maximum supply voltage to 3.6V. Changed Preliminary to Final. 7/16/04 Added AC timing specifications for ACCESS.bus, external bus, GPIO, Microwire/SPI, and UART . Corrected address of flash data memory in Section 8. 11/9/04 Added conditions which clear the ACBST, ACBCST, and ACBCTL1 registers. Added external reset as condition which clears WDRST and ISPRST bits in the MSTAT register. Inverted sense of PEN_DOWN bit in the ADCRESLT register. 4/4/05 Added new reset circuits. Added note about fluctuations in response due to SDI activity. New back page. 9/24/06 Added 14-bit counter delay to external reset. 2/21/07 Updated NSIDs. Table 88 Revision History Date Major Changes From Previous Version Obsolete

32.0 Physical Dimensions (millimeters) unless otherwise noted

Figure 136. LQFP-128 Package Figure 137. LQFP-144 Package

CP3BT23 Reprogrammable Connect ivity Processor with Bluetooth and Dual CAN Interfaces Notes www.national.com Obsolete

Texas InstrumentsIncorporatedand itssubsidiaries(TI)reservetherighttomake corrections,modifications,enhancements,improvements, and otherchanges toitsproductsand servicesatany timeand todiscontinueany productorservicewithoutnotice.Customersshould obtainthelatestrelevantinformationbeforeplacingordersand shouldverifythatsuch informationiscurrentand complete.Allproductsare soldsubjecttoTI’s termsand conditionsofsalesuppliedatthetimeoforderacknowledgment. TIwarrantsperformanceofitshardwareproductstothespecificationsapplicableatthetimeofsaleinaccordancewithTI’s standard warranty.Testingand otherqualitycontroltechniquesareused totheextentTIdeems necessarytosupportthiswarranty.Exceptwhere mandated by governmentrequirements,testingofallparametersofeach productisnotnecessarilyperformed. TIassumes no liabilityforapplicationsassistanceorcustomerproductdesign.Customersareresponsiblefortheirproductsand applicationsusingTIcomponents.To minimizetherisksassociatedwithcustomerproductsand applications,customersshouldprovide adequatedesignand operatingsafeguards. TIdoes notwarrantorrepresentthatany license,eitherexpressorimplied,isgrantedunderany TIpatentright,copyright,mask work right, orotherTIintellectualpropertyrightrelatingtoany combination,machine,orprocessinwhichTIproductsorservicesareused.Information publishedby TIregardingthird-partyproductsorservicesdoes notconstitutea licensefromTItouse such productsorservicesora warrantyorendorsementthereof.Use ofsuch informationmay requirea licensefroma thirdpartyunderthepatentsorotherintellectual propertyofthethirdparty,ora licensefromTIunderthepatentsorotherintellectualpropertyofTI. ReproductionofTIinformationinTIdatabooks ordatasheetsispermissibleonlyifreproductioniswithoutalterationand isaccompanied by allassociatedwarranties,conditions,limitations,and notices.Reproductionofthisinformationwithalterationisan unfairand deceptive businesspractice.TIisnotresponsibleorliableforsuch altereddocumentation.Informationofthirdpartiesmay be subjecttoadditional restrictions. ResaleofTIproductsorserviceswithstatementsdifferentfromorbeyond theparametersstatedby TIforthatproductorservicevoidsall expressand any impliedwarrantiesfortheassociatedTIproductorserviceand isan unfairand deceptivebusinesspractice.TIisnot responsibleorliableforany such statements. TIproductsarenotauthorizedforuse insafety-criticalapplications(suchas lifesupport)where a failureoftheTIproductwouldreasonably be expectedtocause severepersonalinjuryordeath,unlessofficersofthepartieshave executedan agreementspecificallygoverning such use.Buyersrepresentthattheyhave allnecessaryexpertiseinthesafetyand regulatoryramificationsoftheirapplications,and acknowledgeand agreethattheyaresolelyresponsibleforalllegal,regulatoryand safety-relatedrequirementsconcerningtheirproducts and any use ofTIproductsinsuch safety-criticalapplications,notwithstandingany applications-relatedinformationorsupportthatmay be providedby TI.Further,Buyersmust fullyindemnifyTIand itsrepresentativesagainstany damages arisingoutoftheuse ofTIproductsin such safety-criticalapplications. TIproductsareneitherdesignednorintendedforuse inmilitary/aerospaceapplicationsorenvironmentsunlesstheTIproductsare specificallydesignatedby TIas military-gradeor"enhanced plastic." Onlyproductsdesignatedby TIas military-grademeet military specifications.Buyersacknowledgeand agreethatany such use ofTIproductswhichTIhas notdesignatedas military-gradeissolelyat theBuyer's risk,and thattheyaresolelyresponsibleforcompliancewithalllegaland regulatoryrequirementsinconnectionwithsuch use. TIproductsareneitherdesignednorintendedforuse inautomotiveapplicationsorenvironmentsunlessthespecificTIproductsare designatedby TIas compliantwithISO/TS 16949 requirements.Buyersacknowledgeand agreethat,iftheyuse any non-designated productsinautomotiveapplications,TIwillnotbe responsibleforany failuretomeet such requirements. FollowingareURLs where you can obtaininformationon otherTexas Instrumentsproductsand applicationsolutions: Products Applications Audio www.ti.com/audio Communicationsand Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP ® Products www.dlp.com Energyand Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocksand Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space,Avionicsand Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportationand Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Videoand Imaging www.ti.com/video RFID www.ti-rfid.com OMAP MobileProcessors www.ti.com/omap WirelessConnectivity www.ti.com/wirelessconnectivity TIE2E Community Home Page e2e.ti.com MailingAddress:Texas Instruments,PostOfficeBox 655303,Dallas,Texas 75265 Copyright© 2011,Texas InstrumentsIncorporated