CNS002 ETC2 | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 1
Technical content
4 3 OWG NO. ‘SH REV. 1 CNSO02-| 1 |N/C This print and associated documents and the contained Pr —“sSCSCOCtRSNSSC SS ™~<“SOSC~C~CCCCCC”””CS@CS ntormation are the onfidentih property ef ELECTRONIC [eon [amv eer] einen ear CABLE SPECIALISTS. Disclosure of, and/or reproduction eon _[zone | fev. DESCRIPTION pare _|_Approweo of, all or part thereof or manufacture of any part from INSTRUCTIONS 21604 L- lnc NEW_RELEASE [Rhoby Pek | information contained on this print not specifically per— mitted by ELECTRONIC CABLE SPECIALISTS in writing is 1. BEGIN BY CUTTING THE CABLE OFF SQUARE. D_ | forbidden. a D ‘BoDY LOCKWIRE HOLES 8. SLIDE THE BODY OF THE CONNECTOR OVER THE END OF THE 2. WHEN USING AUTOMATIC STRIPPING EQUIPMENT, STRIP CABLE AS CABLE UNTIL THE NOTCH IN THE CONTACT SEATS INTO THE SHOWN STARTING WITH L1 AND ENDING WITH L3. TAKE CARE DIELECTRIC RIDGE INSIDE THE CONNECTOR & }— 1.500 —| NOT TO NICK THE CONDUCTORS WHILE STRIPPING THE DIELECTRIC }ODY. eet AND JACKET. IF AUTOMATIC STRIPPING EQUIPMENT IS NOT — — Reseed sl AVAILABLE, STRIP ONLY L1 AND L3 AND TRIM EXCESS BRAID AT F Presesey Re sgasegest STEP 10. ON RI Ry Peewee = | | Bae Rey & BS Re Ro PRI ssseet 5 a =] Kesey 3 ll =.19 CABLE_CONTACT FERRULE l2 = 31 9. FOLD ALL THREE BRAIDS UP OVER THE NECK OF THE CONNECTOR L3 = 62 BODY. Cepo 3. SLIDE THE FERRULE AND ADHESIVE SHRINK TUBING OVER THE ses Cc Ls00—| END oF THE caBLe/\\, -| | §& ~ |S Cc CAG ate DIMENSIONS /A\\ <| | ik = Re : ‘SPECIFICATIONS 10. SLIDE THE FERRULE UP OVER THE SHIELDS AND UP AGAINST THE 4. SOLDER THE CONTACT ONTO THE CENTER CONDUCTOR, PER CONNECTOR BODY. TRIM AWAY ANY EXCESS BRAID. CRIMP THE ELECTRICAL MIL-STD-2000, USING 63Sn/37Pb SOLDER OR CRIMP WITH FERRULE ONCE, NEXT TO THE BODY, USING THE M22520/5—31 IMPEDANCE: 50 OHMS NOMINAL 1757 DIE. ENSURE THE CONTACT IS BUTTED AGAINST THE DIE IN A M22520/5-01 TOOL FRAME. APPLY ADHESIVE HEAT FREQUENCY RANGE: 0-11 GHz CABLE DIELECTRIC. CLEAN ALL FLUX RESIDUES USING AN SHRINK. /\\, VSWR: 1.2:1 MAXIMUM DC TO 2GHz APPROPRIATE FLUX CLEANER. INSERTION LOSS: .1dB MAXIMUM DC TO 2GHz RESe S WORKING VOLTAGE: 1000 VRMS @ SEA LEVEL Rey DIELECTRIC WITHSTANDING: 2500 VRMS @ SEA LEVEL =-|{| [ J 7\\\\ >| }—] Reed S INSULATION RESISTANCE: 5000 MEGOHMS MINIMUM pws [| Re @ 500 VOLTS DC Resesd S MECHANICAL 5. USING TWEEZERS, FOLD THE OUTER BRAID BACK OVER THE Non ee B CONNECTOR INTERFACE: DIMENSIONS PER, MlL-STD— S484 CABLE JACKET, LEAVING AS MUCH WEAVE AS POSSIBLE. NOTES B FIGURE 304-1 (N TERMINATION STYLE: CENTER CONTACT-SOLDER OR CRIMP Ss FERRULE—CRIMP = | || y Cp caste reveNtion: 6oe re || M | / \\etr— ZA, INSURE HEAT SHRINK IS INSTALLED PRIOR TO CRIMPING CONNECTOR. DX ADHESIVE HEAT SHRINK SHOULD BE APPLIED IN ACCORDANCE WITH ECS WORK TEMPERATURE RATING: | 65° TO +165" C EVERY 1/8”. GENTLY ROTATE PIN TO SEPARATE THE FLAT FOIL ee Met poe eMOb POE COND: 8 BRAID AND ALUMINUM/POLYESTER FOIL FROM THE DIELECTRIC. \\ CONNECTOR DIMENSIONS ARE FOR REFERENCE ONLY. THERMAL SHOCK: MIL—STD-202, METHOD 107, COND. B USING TWEEZERS, FOLD BACK ALUMINUM/POLYESTER FOIL CORROSION: MIL-STD-202, METHOD 101, COND. 8 : MOISTURE RESISTANCE: MIL-STD-202, METHOD 106 - PRSy\\ ei MATERIALS =| | BS Sia TRONI BODY: BRASS PER QQ-B-626 ws ALL LENGTHS IN INCHES pts Euec ONG CABLE © PECIALISTS T OTHER SHIELDS, LEAVING AS MUCH WEAVE AS POSSIBLE. - me: A OUTER CONTACT: BRASS PER QQ--B~626 NOTE: DO NOT UNRAVEL DIELECTRIC WHEN PULLING BACK CUSTOMER SPECIFICATION DIELECTRIC: TEFLON PER L-P-403 INNER SHIELD a STRAIGHT N TYPE PLUG A GASKET: SILICONE RUBBER PER ZZ—R-765 ; GER VA b2fa)o4 | FOR ECS CABLE 310701 Lex DESIGNED BY Ui 0 EINISHES = | | Sa per ‘SIZE | CAGE CODE PART NO. BODY, FERRULE AND OUTER CONTACT: BRIGHT NICKEL <i PROKECT ENG: BER O0-N-290 By pores” | |B} 66197 CNSO02 CENTER CONTACT: GOLD PER MIL—G—45204 BAK IEAM. _|!efufet sous: [rus vo exnareevcomnernsons sree 1 or 1 _|