CMD-KEYX-315 LINX | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
With a one-time NRE and minimum order, Linx can configure the keypad and label areas to meet your specific requirements. Contact Linx for details. OEM KEYFOB TRANSMITTER DATA GUIDE CMD-KEYX-XXX
DESCRIPTION
The Linx CMD-KEYX-XXX Remote Command keyfob is ideal for general- purpose remote control and command applications. The unit has been pre- certified for FCC Part 15 compliance which reduces costs and time to product introduction. Available in 315, 418 or 433.92 MHz (418MHz standard), this stylish and compact remote is capable of 100+ ft. transmission range. The unit can be configured with 1-5 buttons and the keypad and labeling can be customized to meet specific customer requirements. Selectable addressing provides security and allows for 2 10 distinct transmitter- receiver relationships. The trans- mission can be decoded using a matching Linx function module, a KH series receiver/decoder module or a Linx LC series receiver paired with a decoder IC or microcontroller. The unit operates from a single 3-volt lithium cell. 2.24" (57.4) 0.99" (25.4) 0.45" (11.5) 1.35" (34.6) S1 S3S5 I Remote Control / Command I Keyless Entry I Garage / Gate Openers I Lighting Control I Security / Call Systems I Home / Industrial Automation APPLICATIONS INCLUDE: PART # DESCRIPTION CMD-KEYX-315 315 MHz Keyfob Transmitter CMD-KEYX-418* 418 MHz Keyfob Transmitter CMD-KEYX-433 433 MHz Keyfob Transmitter X= # of buttons - insert 1-5 * = Standard Frequency
ORDERING INFORMATION
The CMD-KEYX-XXX Keyfob Command Unit combines a high-performance SAW- (Surface Acoustic Wave) based transmitter with an on-board encoder. The keyfob can transmit the status of 1 to 5 buttons along with the state of ten address lines for security and creation of unique transmitter/receiver relationships. The product’s operation is straightforward. When a button is pressed, power is applied to the internal circuitry and the encoder IC is enabled. The encoder then detects the logic states of the address traces and button data lines. These states are then formatted into a 3-word transmission cycle which continues until the button is released. The encoder data is used to modulate the transmitter which through the antenna conveys the data into free space. The transmitted signal may be received by any Linx KH or LC receiver or pre-made function module of the same frequency. Once data is received it is decoded using a decoder IC or custom microcontroller. The transmitted address bits are checked against the address settings of the receiving device. If a match is confirmed, the decoder’s output(s) are set to replicate the transmitter’s button status. 1. Current draw with 50% mark/space ratio. 2. Current draw in standby Notes: RF-Parameters CMD-KEYX-418 Designation Min. Typical Max. Units Notes Frequency of Carrier F C 417.925 418 418.075 MHz – Harmonic Emissions P H –– -40 dBc – RF-Parameters CMD-KEYX-433 Designation Min. Typical Max. Units Notes Frequency of Carrier F C 433.845 433.92 433.995 MHz – Harmonic Emissions P H –– -45 dBc – RF-Parameters CMD-KEYX-315 Designation Min. Typical Max. Units Notes Frequency of Carrier F C 314.925 315 315.075 MHz – Harmonic Emissions P H –– -40 dBc – ABOUT THESE MEASUREMENTS The performance parameters listed below are based on module operation at 25°C from a 3Vdc supply unless otherwise noted. PERFORMANCE DATA– CMD-KEYX-XXX Electrical Parameters CMD-KEYX- 315,418, 433MHz Designation Min. Typical Max. Units Notes Operating Voltage Range V CC 2.7 – 3.2 Vdc – Current Average I CA – 1.7 – mA 1 Current In Sleep I SLP – 0- µ A 2 Output Power P O PART 15.231 Compliant TX Data length 26bits 3x Average Data Duty Cycle 50% Encoder Oscillator FE NC 70 KHz Operating Temperature -30 °C to +70 °C
SETTING THE TRANSMITTER ADDRESS The keyfob allows the selection of one of 1024 unique addresses. All keyfobs from the factory are supplied set to the same address. To avoid ID contention with other units in the vicinity or to create unique relationships it may be helpful to change the address settings. This may be accomplished by cutting the appropriate jumper trace(s) with a sharp object such as an X-acto knife as shown. The traces are accessed by removing the rear cover as for battery replacement. CONTENTION CONSIDERATIONS It is important to understand that only one transmitter at a time can be activated within a reception area. While the transmitted signal consists of encoded digital data, only one carrier of any frequency can occupy airspace without contention at any given time. BATTERY REPLACEMENT The remote unit utilizes a CR-2032 Button Lithium Cell. In normal use it will provide 1-2 years of operation. Access for replacement is accomplished by gently prying apart the two halves of the keyfob at the seam (fingernails will do for this). Once the unit is open, remove the battery by sliding the battery out from beneath the retainer. Replace with the same type of cell while observing the polarity shown. COMPLIANCE REQUIREMENTS The CMD-KEYX-XXX has been pre-certified by Linx for FCC Part 15 compliance when used with an appropriate function module in keeping with the applications allowed under section 15.231. LABELING/INSTRUCTION REQUIREMENTS The CMD-KEYX-XXX Remote Command Unit has already been labeled in accordance with FCC regulations in effect as of the date of this document. No further labeling of the unit is needed; however, it is necessary to include the statement on page 7 in the end product’s instruction manual or insert card. 0123456789 Battery
12 GND
11 OSC1
10 OSC2
8 DOUT
& Filter Keyed Output 50 Ω RF OUT (Ant.) Schematic Diagram
24VCC 23D0 22A9 21A8 20A7 19A6 18A5 17A4 16A3 15A2 14A1 13A0GND OSC1 OSC2 TE DOUT ation RF Amplifier Vcc SAW Oscillator S1 S3S5
USING THE KEYFOB WITH LINX RECEIVER MODULES Keyfobs are shipped with all address lines tied to ground (Default) with 1024 possible address combinations available by cutting address traces. The Keyfob works directly with the KH series receiver/decoder modules when A0-A9 are set to the same configuration as the keyfob address lines. Because the Function Decoder Module only has 9 address lines, the #9 address line on the keyfob must be cut. Address lines 0-8 must match the configuration in the keyfob for 512 possible addresses. Also be sure to tie the function decoder's mounting hole directly to groundplane to further enhance performance. The LC receiver module can be used with an appropriate decoder such as Holtek’s HT -658 for 1024 possible addresses. NC1 D02 D13 GND4 VCC5 PDN6 D27 D38 D49 DATA10 VT11 D512 D613 D714 A0 15 A1 16 A2 17 A3 18 A4 19 A5 20 A6 21 A7 22 A8 23 A9 24 NC 25 NC 26 GND 27 ANT 28 LOT 1000 RF RECEIVER/DECODER RXD-418-KH 10 11 SW-DIP-10 GND D111 D122 D133 D144 D155 D166 D177 VT8 DIN9 OSC210 OSC111 GND12 A0 13A1 14A2 15A3 16A4 17A5 18A6 19A7 20A8 21A9 22D10 23VCC HT -658 HT -658 FCC Precertified Decoder Function Module LC Receiver Module Keyfob Address Lines KH Series Receiver/Decoder Module
This equipment has been tested and found to comply with the limits for a Class-B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment has been certified to comply with the limits for a Class-B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment. Place the above statement in the instruction manual or insert card.
LINX TECHNOLOGIES, INC. 575 S.E. ASHLEY PLACE GRANTS PASS, OR 97526 PHONE: (541) 471-6256 FAX: (541) 471-6251 http://www.linxtechnologies.com U.S. CORPORATE HEADQUARTERS: Linx Technologies is continually striving to improve the quality and function of its products; for this reason, we reserve the right to make changes without notice. The information contained in this Data Sheet is believed to be accurate as of the time of publication. Specifications are based on representative lot samples. Values may vary from lot to lot and are not guaranteed. Linx Technologies makes no guarantee, warranty, or representation regarding the suitability or legality of any product for use in a specific application. None of these devices is intended for use in applications of a critical nature where the safety of life or property is at risk. The user assumes full liability for the use of product in such applications. Under no conditions will Linx Technologies be responsible for losses arising from the use or failure of the device in any application, other than the repair, replacement, or refund limited to the original product purchase price. Some devices described in this publication are patented. Under no circumstances shall any user be conveyed any license or right to the use or ownership of these patents. Disclaimer © 2000 by Linx Technologies, Inc. The stylized Linx logo, Linx, and “Wireless Made Simple” are the trademarks of Linx Technologies, Inc. Printed in U.S.A.