CLL CLAIREX | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Clairex Technologies, Inc. 1301 East Plano Parkway Plano, Texas 75074-8524 Phone: 972-265-4900 Fax: 972-265-4949 www.clairex.com CLL Series Photo-IC Sensors Digital Output Clairex Technologies, Inc. March, 2003 Clairex reserves the right to make changes at any time to improve design and to provide the best possible product. Page 1 of 4 Case 21 2. VCC 3. GROUND 4. ADJUST 1. OUTPUT 0.028 (0.71) 0.048 (1.22) 0.046 (1.17) 0.036 (0.91) 45°0.209 (5.31) 0.230 (5.84) 0.060 (1.52) max 0.210 (5.33) 0.500(12.7) min. 0.190 (4.83) 0.187 (4.75) 0.179 (4.55) 0.030 (0.76) max. 0.210 (5.33) 0.500(12.7) min. 0.190 (4.83) 0.187 (4.75) 0.179 (4.55) 0.030 (0.76) max. 0.010 (0.25) max 2. VCC 3. GROUND 4. ADJUST 1. OUTPUT 0.028 (0.71) 0.048 (1.22) 0.046 (1.17) 0.036 (0.91) 45°0.209 (5.31) 0.230 (5.84) Case 22 Case 21 2. VCC 3. GROUND 4. ADJUST 1. OUTPUT 0.028 (0.71) 0.048 (1.22) 0.046 (1.17) 0.036 (0.91) 45°0.209 (5.31) 0.230 (5.84) 0.060 (1.52) max 0.210 (5.33) 0.500(12.7) min. 0.190 (4.83) 0.187 (4.75) 0.179 (4.55) 0.030 (0.76) max. 0.210 (5.33) 0.500(12.7) min. 0.190 (4.83) 0.187 (4.75) 0.179 (4.55) 0.030 (0.76) max. 0.010 (0.25) max 2. VCC 3. GROUND 4. ADJUST 1. OUTPUT 0.028 (0.71) 0.048 (1.22) 0.046 (1.17) 0.036 (0.91) 45°0.209 (5.31) 0.230 (5.84) Case 22 TO-72 CLL130 CLL131 CLL133 TO-72 CLL130W CLL131W CLL133W TO-18 CLL134 CLL135 CLL136 CLL137 TO-18 CLL134W CLL135W CLL136W CLL137W ALL DIMENSIONS ARE IN INCHES (MILLIMETERS)

features

  • Output stages: a. Buffer or inverter b. Open collector or internal 10KΩ pull-up
  • Supply voltage 4.5V to 18V
  • 7:1 user sensitivity adjustment on CLL130-CLL133 and CLL130W-CLL133W series
  • Acceptance angle: a. ± 15° high dome lens can b. ± 35° flat window lens can
  • Operates to 125°C
  • RoHS compliant

description

The CLL series are monolithic integrated circuits incorporating a photodiode, linear amplifier, Schmitt trigger for hysteresis and pulse shaping, and digital output with either 10KΩ pull-up or open collector. The series includes TO-72 four leaded packages (with user adjustable gain) and TO-18 three leaded packages in both high dome and flat window configurations. Alternate pin-outs are available. Contact Clairex. 0.210 (5.33) 0.190 (4.83) Revised 3/16/06 2. VCC 3. GROUND 4. ADJUST 1. OUTPUT 0.028 (0.71) 0.048 (1.22) 0.046 (1.17) 0.036 (0.91) 45°0.209 (5.31) 0.230 (5.84) 0.060 (1.52) max 0.157 (3.99) 0.500(12.7) min. 0.137 (3.48) 0.187 (4.75) 0.179 (4.55) 0.030 (0.76) max.

Clairex Technologies, Inc. 1301 East Plano Parkway Plano, Texas 75074-8524 Phone: 972-265-4900 Fax: 972-265-4949 www.clairex.com CLL Series Photo-IC Sensors Digital Output Schematics Clairex Technologies, Inc. VCC ADJ VOUT GND CLL133/CLL133W Open collector – inverter with Adjust VCC ADJ 10kΩ VOUT GND CLL131/CLL131W 10kΩ pull-up – inverter with Adjust VCC ADJ 10kΩ VOUT GND CLL130/CLL130W 10kΩ pull-up – buffer with Adjust VREG LA VCC VOUT GND CLL135/CLL135W Open collector - inverter VCC VOUT GND CLL134/CLL134W Open collector - buffer VREG LA VREG VREG LA VREG LA VCC 10kΩ VOUT GND CLL137/CLL137W 10kΩ pull-up – inverter VREG LA VCC 10kΩ VOUT GND CLL136/CLL136W 10kΩ pull-up – buffer VREG LA Clairex reserves the right to make changes at any time to improve design and to provide the best possible product. Page 2 of 4 LA

Clairex Technologies, Inc. 1301 East Plano Parkway Plano, Texas 75074-8524 Phone: 972-265-4900 Fax: 972-265-4949 www.clairex.com CLL Series Photo-IC Sensors Digital Output Absolute maximum ratings (TA = 25°C unless otherwise stated) I SINK NOTES: 1. 1/16” from the case for 5 seconds maximum. 2. This rating applies when the output is in the OFF state only. 3. This rating applies when the output is in the ON state only. 4. Derate linearly 2.0mW/°C from 25°C free air to T A = 125°C. 5. CLL130-CLL133 and CLL130W-CLL133W photo-IC sensors are tested with the ADJ lead open. 6. Light source is an AlGaAs IRED with peak wavelength at 850nm. DEFINITIONS:

  • Ee (+) is the minimum irradiance required to cause the output to change state.
  • Buffer: Output is HIGH when input irradiance is >Ee (+).
  • Inverter: Output is LOW when input irradiance is >Ee (+). electrical characteristics (TA = 25°C unless otherwise noted) parameter symbol min typ max units test conditions Operating supply voltage V CC 4.5 - 18 V Positive going threshold irradiance(6) Ee (+) 0.005 0.025 0.05 0.25 mW/cm2 mW/cm2 4.5V ≤ VCC ≤ 18V, ADJ open, All non-suffix W parts. All suffix W parts. Hysteresis ratio EeT (+) EeT (-) 1.1 - 1.8 operate point/release point Supply current I CC - - 12 mA 4.5V ≤ VCC ≤ 18V, Ee = 0 or 0.5mW, ADJ open Total acceptance angle ΘP - deg. deg. All non-suffix W parts All suffix W parts Gain threshold can be adjusted on the CLL130-CLL133 and CLL130W-CLL133W series by placing a resistor between the ADJ and GND leads in accordance with the following table. Decreasing the resistance causes the output to switch at a higher threshold level. ADJ Resistor Normalized Threshold open 1.00 10k 2.00 4.7k 2.75 2.2k 3.75 1k 5.00 Connected to GND 7.25 Clairex Technologies, Inc. Clairex reserves the right to make changes at any time to improve design and to provide the best possible product. Page 3 of 4

Clairex Technologies, Inc. 1301 East Plano Parkway Plano, Texas 75074-8524 Phone: 972-265-4900 Fax: 972-265-4949 www.clairex.com CLL Series Photo-IC Sensors Digital Output electrical characteristics (TA = 25°C unless otherwise noted) parameter symbol min typ max units test conditions CLL130/CLL130W and CLL136/CLL136W (buffer, 10kΩ pull-up) High state output voltage V OH 4.5 - - V VCC = 5.0V, Ee (+) ≥ 0.5mW/cm2 Low state output voltage V OL - - 0.4 V V CC = 5.0V, Ee (+) = 0 Output rise and fall time t r, tf - 75 - ns Propagation delay t PHL, tPLH - 5 - µs VCC = 5.0V, Ee = 0 or 0.5mW/cm2, f = 10kHz, CLL131/CLL131W and CLL137/CLL137W (inverter, 10kΩ pull-up) High state output voltage V OH 4.5 - - V V CC = 5.0V, Ee (+) = 0 Low state output voltage V OL - - 0.4 V VCC = 5.0V, Ee (+) ≥ 0.5mW/cm2 Output rise and fall time t r, tf - 75 - ns Propagation delay t PHL, tPLH - 5 - µs VCC = 5.0V, Ee = 0 or 0.5mW/cm2, f = 10kHz, CLL134/CLL134W (buffer, open collector) High state output current I OH - - 100 µA VCC = 5.0V, VOH = 30V Ee (+) ≥ 0.5mW/cm2 Low state output voltage V OL - - 0.4 V VCC = 5.0V, Ee (+) = 0 RL = 330Ω Output rise and fall time t r, tf - 75 - ns Propagation delay t PHL, tPLH - 5 - µs VCC = 5.0V, Ee = 0 or 0.5mW/cm2, f = 10kHz, CLL133/CLL133W and CLL135/CLL135W (inverter, open collector) High state output current I OH - - 100 µA VCC = 5.0V, VOH = 30V Ee (+) = 0 Low state output voltage V OL - - 0.4 V VCC = 5.0V, RL = 330Ω Ee (+) ≥ 0.5mW/cm2 Output rise and fall time t r, tf - 75 - ns Propagation delay t PHL, tPLH - 5 - µs VCC = 5.0V, Ee = 0 or 0.5mW/cm2, f = 10kHz, NOTE: Due to the high sensitivity of the CLL series, when used in high speed switching applications, Clairex recommends installing a 0.1µF capacitor between VCC and GND. Clairex reserves the right to make changes at any time to improve design and to provide the best possible product. Page 4 of 4 Clairex Technologies, Inc.