CFL-2LPP-044N2TSH-A-100D

C.FL HIROSE | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 8

Technical content

2022.1ᶆ C.FL Series NEW ■Features 1. Supports up to 30GHz High frequency performance from DC to 30GHz. Suitable for the 28GHz band expected to be used in 5G communications. 2. Mated Height of 0.92mm (1.0mm Max.) Receptacle mounting area is only 3.4mm2. Using the right-angle plug enables a mated height of 0.92mm, achieving the world's lowest class profile of coaxial connectors. (Fig.1) 3. Ultra lightweight The world's smallest and lightest class of coaxial connectors. Receptacle : 3.3mg Right angle plug : 14.1mg 4. Automatic Board Placement The embossed packaging allows for the receptacles to be automatically placed. 5. 50Ω Ultra-fine coaxial (fluorinated resin insulated) cables Ultra-fine coaxial cables with a finished outer diameter of Ø0.64mm (single shield) allow for connection in small, confined spaces with smooth and easy operation. 6. Tactile Lock Clear tactile lock on small connector enables reliable mating. 7. Simple Connector Mating and Unmating Dedicated Insertion and Extraction tools to enable proper mating/unmating. 3.3 0.92 C.FL-LP(P)-044 C.FL-R-SMT-1 Mated Condition Fig.1 50Ω Supporting up to 30GHz In cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information.

C.FL Series●0.92mm mated height Low Height and Light Weight Miniature Coaxial Connectors Supporting up to 30GHz ■Product Specifi cations Ratings Nominal characteristic impedance 50Њ Operating Temperature -40 to +90 ˆ (90ˋRH Max.) Frequency Range : DC to 30GHz Storage Humidity Range -20 to +70 ˆ (90ˋRH Max.) Item Specifications Conditions 1. Contact Resistance Center : 60m Њ Max.ɹExterior : 20mЊ Max. Measured at a maximum of 10mA 2. Insulation Resistance 500 ̢Њ min Measured at 100V DC 3. Withstanding Voltage There shall be no flashover or dielectric breakdown Apply 200V for 1 minute 1.4 Max. DC to 15GHz 1.5 Max. 15 to 20GHz 1.6 Max. 20 to 30GHz 5. Durability Contact Resistance Center : 65mЊ Max. Exterior : 25mЊ Max. 20 mating cycles *V.S.W.R. Measuring System Note 1 : The cable connector is measured with a 2.4mm conversion adapter attached to double-ended harness with an applicable 10cm cable. Note 2 : The board connector is measured while mounted to a 50 Њ flourine board with a 2.4mm conversion adapter attached. ■Material / Finish Component Material Finish/Remarks Right angle Plug Shell Phosphor bronze Partial gold plating Insulator LCP resin Black, UL94V-0 Female Central Contact Phosphor bronze Gold plating Receptacle Shell Phosphor bronze Gold plating Insulator LCP resin Black, UL94V-0 Male Central Contact Brass Gold plating Adapter Shell Stainless steel Nickel Plating Insulator PTFE resin ʕ Male Center Contact Phosphor bronze Gold plating Female Central Contact Beryllium copper Gold plating <Plug Harness Measurement System> <Receptacle Measurement System> Vector Network Analyzer Vector Network Analyzer APC2.4(F) APC2.4(M) APC2.4(F) APC2.4(M) D.U.T. D.U.T. C.FLJ-H2.4P C.FL-LP(P)-044 100mm Double-ended Harness C.FLJ-H2.4P CONVERSION ADAPTOR Test Board C.FL-R-SMT-1 C.FLP-H2.4J

C.FL Series●0.92mm mated height Low Height and Light Weight Miniature Coaxial Connectors Supporting up to 30GHz ■Plug 1.92 3.3 L(mm) ˔Cable Harness Total Length Standard Tolerance Total Length L Standard Tolerance (mm) 41ʽLʽ170 ±0.3 ɹ ˔Plug Product Number Structure Refer to the charts below for determining specific part number characteristics. Please select connectors listed in this catalog when placing orders and be sure to check the latest delivery specifications at the time of ordering the product. CFL - 2LPP - 044NʮʯTSH - A - L ˔C.FL-LP(P)-044 (Applicable Cable : outer diameter П0.64mm) ■Cable Harness Specifi cation The dimension specifications of the C.FL Series harness are as follows. ʦConnector double-ended harnessʧ ⁞Series NameɹC.FL Harness Type 2LPP : Double-ended L-shaped plug harness ⁠Cable Type 044N : Ø0.64 cable ⁡Cable Color 1 : White, 2 : Black, 4 : Blue ⁢Cable Outer Conductor Specifications TSH : Tin plated coiled shield ⁣Total Length (mm) Length L (Based on mating center, Unit : mm) Please order plug with as cabled assembly BHigh Frequency Characteristic Data (Typical Value)

C.FL Series●0.92mm mated height Low Height and Light Weight Miniature Coaxial Connectors Supporting up to 30GHz ■Receptacle Part No. HRS No. Packaging ̧̨̝̾̎ C.FL-R-SMT-1(90) 331-2200-0 90 20,000 pieces per reel ˓ 0.58 Ø1.4 0.3 1.7 1.7 1.3 0.3 GNDGND GND SIG 0.43 1.3 1.3 0.65 2.6 1.4 0.5 1.5 SIG No conductive traces in this area ⿆Recommended PCB Mounting Pattern ˔Receptacle Product Number Structure Refer to the charts below to determine specific part number characteristics. Please select connectors listed in this catalog when placing orders and be sure to check specifications at the time of ordering. C.FL - R - SMT-1 ⁞ ⁠ ⁞Series NameɹC.FL Connector Type R : Receptacle ⁠Mounting Method SMT-1 : Surface Mounting BHigh Frequency Characteristic Data (Typical Value) ˔Embossed Tape Specifi cations (JIS C 0806/IEC60286 Standard) ˔Reel Specifi cations (0.67) (0.25)Ø1.5 3.5 1.75 Pull Direction SIG 9.5 Ø380

C.FL Series●0.92mm mated height Low Height and Light Weight Miniature Coaxial Connectors Supporting up to 30GHz 8HEX M7ʷ0.75-6H (12.19) 5.62.4mm Identification Groove M7ʷ0.75-6g Ø6.35 13.9 (11.99) 1/4-36UNS-2B 8HEX C.FLJ-H2.4P 311-0017-0 ˓ Note : The mated portion of the C.FL side has a lower lock retention force than regular products so the adapter cannot be used for purposes other than performance measurements. C.FLP-H2.4J 311-0021-0 ˓ Note : The mated portion of the C.FL side has a lower lock retention force than regular products so the adapter cannot be used for purposes other than performance measurements. C.FLJ-HKP 311-0023-0 ˓ Note : The mated portion of the C.FL side has a lower lock retention force than regular products so the adapter cannot be used for purposes other than performance measurements. ˔2.4mm Conversion Adapter (Mated Portion : C.FL side : Jack-2.4mm side : Plug) ˔2.4mm Conversion Adapter (Mated Portion : C.FL side : Plug-2.4mm side : Jack) ˔2.92 Conversion Adapter (Mated Portion : C.FL side : Jack-2.92mm side : Plug) ■Conversion Adapter

C.FL Series●0.92mm mated height Low Height and Light Weight Miniature Coaxial Connectors Supporting up to 30GHz 3.02 (2.6) Extraction SideInsertion Side (60) X.FL(V)-LP-IN.OUT 331-0076-0 ˓ Note : The insertion and extraction tool may be deformed or damages if dropped, etc. so please handle with care. 5.6 1/4-36UNS-2A 2.92mm Identification Groove Ø6.35 13.9 C.FLP-HKJ 311-0024-0 ˓ Note : The mated portion of the C.FL side has a lower lock retention force than regular products so the adapter cannot be used for purposes other than performance measurements. Tool for mating and unmating the plug. ■Insertion and Extraction Tool ˔2.92 Conversion Adapter (Mated Portion : C.FL side : Plug-2.92mm side : Jack)

C.FL Series●0.92mm mated height Low Height and Light Weight Miniature Coaxial Connectors Supporting up to 30GHz ⿆Usage Precautions ɹ1. Plug (1) Mating / un-mating ᶃTo un-mate, use the extraction tool X.FL-LP-IN.OUT as shown in the following figure. [How to un-mate a plug] Do not un-mate a connector by pulling the cable as it may cause damage to the connector. ᶄTo mate a connector, use the mating side of the plug mating and unmating tool X.FL-LPIN. OUT. Align the mating axes between both connectors and check that the shell is properly aligned. The connector should be inserted perpendicularly as much as possible. (See the following figure) (2) Pull forces on the cable after connectors are mated Once the connector is mated, do not apply a load to the cable in excess of the values indicated in the figure below. Be careful when lifting the cable as it may add a load or cause unmating. It is recommended to place buffer on the plug when wiring in a direction that causes the cable to lift. (See figure below) 1.05±0.05 Buffer ʢ3ʣPrecautions Do not mate or unmate a connector with an excessive force as it may damage the connector. X.FL(V)-LP-IN.OUT X.FL(V)-LP-IN.OUT 2N Max. C.FL-R-SMT-1 C.FL-LP(P)-044

C.FL Series●0.92mm mated height Low Height and Light Weight Miniature Coaxial Connectors Supporting up to 30GHz ɹ2. Receptacle (1) Recommended reflow temperature profile [reference] 1. The temperatures indicated are the surface temperatures on the printed circuit board at the points of contact with the terminals. 2. Reflow soldering should be performed at peak temperature of 250°C or less at the surface of the printed circuit board. 3. The temperature profile varies depending on conditions such as the size of the printed circuit board, the solder paste type, and solder thickness. (2) Recommended metal mask thickness 0.1mm (3) Reflow cycles 2 times ɹ3. Operating Environment and Storage Conditions ʢ1ʣOperating environment This product was designed under the assumption that it would be used in a normal operating environment. Use of this connector under adverse environmental conditions such as those described below is not advised and may lead to discoloration or other kinds of degradation. ɾRegions having exposure to excessive amounts of fine particles and dust ɾAreas with high densities of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other corrosive gases. (e.g., exhaust gas from automobiles or factories) ɾEnvironments having a large difference in temperature, such as near a heater. ʢ2ʣStorage conditions Store the product in Hirose Electric's packaging or similar packaging conditions. Temperature : -10 to +40°C, humidity : 85% or less (recommended storage conditions) Use the product within six months from delivery. Products for which the storage period has expired must be tested for solderability before the use. Soldering profile for lead free solder (reference) 5FNQFSBUVSFʢˆʣ TFDPSMFTT TFDPOETPSMFTT 1SFIFBUUJNF TFDPOETPSMFTT TFDPOETPSMFTT 4PMEFSJOHUJNF 5JNF TFDPOET The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 01/2022. Contents are subject to change without notice for the purpose of improvements. 2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN https://www.hirose.com/