CCM01-6101 CK-COMPONENTS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Features

  • Available in standard or reverse card reading version, with direct PCB soldering for reduced installation cost.
  • Panel mount version comes with improved noise reduction FPC, to accommodate all front panel configurations.
  • Double sided version allows the customer to insert the card chip up or down for easier handling.
  • Self cleaning card detection switch (normally closed) is protected against assembly mishandling.
  • Available with 8 through hole contacts specifically designed to reduce card wear.
  • A chamfer opening to the card entry slot improves the card guidance into the connector.
  • Variable distance from lower card side to PCB to level card slot with your front panel design
  • Easy insertion into PCB provided by four half pegs and termination true positioning insulator.
  • Four snap in board locks to lower stress on soldered terminals and improve interconnect PCB retention.
  • Thermoplastic UL 94 V-0 insulator suitable for wave soldering only
  • Designed to be compatible with: NDS EMVCo

1 Termination true positioning insulator not

designed on low profile version 3,9 mm EMVTM is a trademark owned by EMVCoLLC. Designation Standard Version Reverse Version Distance from lower card entrance & PCB 3,90 mm CCM01-6101 CCM01-6201 6,75 mm CCM01-6202 6,50 mm CCM01-6105 8,00 mm CCM01-6103 Panel Mount CCM01-6301 CCM01-6302 Double Decker CCM01-6402 CCM01-6403 Construction Mechanical Data Contact Electrical Data Switch Electrical Data Environmental Data Packaging Ordering Code EMVTM compatible

A A 61,1 ±0,2 Card entry54,2 +0,2 0 ( )3,9 5,9 19,05 19,05 ø 3,10,4 A B 22,12 3x 2,54 3,81 4,2 1,6 PCB Thickness Card entry 0,9±0,053,9 6,8 15,4±0,2 Card stop 0,75±0,25 3,7±0,2 0,70,6 A B 1010 2,54 36,4 2,9±0,3 25˚ 29 29 ( )58 ()40()50,3 10x Card entry Designation & Date-Code area 6101 XXXX Pick and place area Embossed Channel

4 Snap feet

A B PCB Layout 22,12 24,66 27,2 29,74 33,55 16,51 19,05 19,05 ø 3,2+0,1 0ø 1+0,1 0 ( )3,81( )3,81 4x10x C1 C2 C3 C4 SW C5 C6 C7 C8 SW (Component side) Card end travel switch terminals Plastic outline Contact location according to ISO 7816-2 ø0,1 ø0,1 CCM01 MK III Dimensions are shown in mm Specifications and dimensions subject to change www.ck-components.com CCM01-6101 Unless otherwise stated, tolerances are ± 0,10 mm Drawings shown for reference only. For other part numbers please consult your local Cannon Customer Service Center. CCM01-6101

Dimensions are shown in mm Specifications and dimensions subject to change www.ck-components.com Dimensional Drawings A A 1010 ø 3,10,4 A B 3,7 ±0,2 5,9 0,75 ±0,25 15,4 ±0,2 Card stop20 22,12 4,2 1,6 PCB Thickness 3,9 Card entry 0,9 ±0,05 61,1 ±0,2 Card entry54,2 +0,2 0 ( )3,9 7,8 3,81 36,4 2,9 ±0,3 19,05 16,51 0,70,6 A B 3x 2,54 25˚ 29 29 ( )58 ()40()50,3 10x Card entry 6201 XXXX Designation & Date-Code area A-A Card stop Embossed Channel A B PCB Layout 18,31 22,12 24,66 27,2 29,74 16,51 19,05 ( )3,81( )3,81 ø 3,2 +0,1 0ø 1+0,1 0 4x10x C1C2C3C4 SWC5C6C7C8 SW (Component side) Card end travel switch terminals Plastic outline Contact location according to ISO 7816-2 ø0,1 ø0,1 CCM01-6201 CCM01 MK III Unless otherwise stated, tolerances are ± 0,10 mm Drawings shown for reference only. For other part numbers please consult your local Cannon Customer Service Center. CCM01-6201