CCDLF-10000L COILCRAFT | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
© Coilcraft, Inc. 2009 Specifications subject to change without notice. Please check our website for latest information. SMT Data Line EMI Filters – CCDLF Document 511-1 Document 511-1 Revised 10/30/08 Current L DCR max min max Color Part number1 Lines (mA)2 (µH)3 (mOhms) Dot CCDLF 10000L_ 10 100 5 250 Brown CCDLF 8000L_ 8 100 5 250 Black CCDLF 8500L_ 8 500 5 200 Green 1. When ordering, please specify termination and packaging codes: CCDLF 8500LD Termination L = RoHS compliant tin-silver-copper over silver-platinum Special order: S = non-RoHS tin-lead (63/37). Packaging D =1 3″ machine ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Current rating is for each line. 3. Inductance is per winding, tested at 1 MHz. 4. Operating temperature range -40°C to +85°C. 5. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Designer’s Kit D303 contains four each of all values plus DLF and PDLF filters Core material Ferrite Terminations RoHS compliant tin-silver-copper over silver- platinum. Other terminations available at additional cost. Weight CCDLF 8000: 540 mg; CCDLF 8500: 559 mg;CCDLF 10000: 670 mg Ambient temperature –40°C to +85°C Storage temperature Component: –40°C to +85°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Mean Time Between Failures (MTBF) 26,315,789 hours Packaging 1000/13″ reel Plastic tape: 16 mm wide CCDLF8x00: 10.46 mm thick, 12 mm pocket spacing, 4.5 mm pocket depth CCDLF10000: 10.28 mm thick, 12 mm pocket spacing, 5.0 mm pocket depth PCB washing Only pure water or alcohol recommended -10 0.1 1 10 100 1000 Frequency (MHz) Attenuation (dB) Common Mode Differential Mode *Measured on HP 8753D network analyzer. Ref: 50 Ohms. Typical Response* Available in 10 and 8-line versions See our PDLF series for 4, 3 and 2-line EMI filters Exceptional common mode noise attenuation from 15 MHz to 300 MHz; p asses signal line data below 300 MHz with minimal attenuation DC current capacity of 500 or 100 mA. Excellent electrical isolation (300 Vrms)
© Coilcraft, Inc. 2009 Surface Mount Data Line EMI Filters Specifications subject to change without notice. Please check our website for latest information. Document 511-2 Document 511-2 Revised 10/30/08 0.170 4,32 max 0.050 1,27 cen 0.030 0,76 0.020 0,51 0.050 1,27 0.230 5,84 0.270 6,86 206 197 188 179 1610 Recommended Land Pattern 0.360 9,14 0.050 1,27 0.030 0,76 0.040 1,02 0.060 1,52 max cen typref 0.360 9,14 max CCDLF 10000 0.170 4,32 max 0.305 7,75 max 0.305 7,75 max 0.030 0,76 0.050 1,27 cen 0.040 1,02 typ0.060 1,52 ref 0.050 1,27 cen 0.030 0,76 0.020 0,51 0.050 1,27 0.180 4,57 0.220 5,59 Recommended Land Pattern CCDLF 8000, 8500 Dimensions are in inches mm Dimensions are in inches mm Dot indicates pin 1 Part number Parts manufactured prior to Sept 2007 may not be marked with part number and internal code. Internal code CCDLF 8000L X