CC32251R0ML ABC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

20~40se c b e﹒Remark：Products comply with RoHS' d﹒Encapsulate：Epoxy novolac Ⅳ﹒GENERAL SPECIFICATION： d﹒Operating temp.：-40℃----+125℃ c﹒Storage temp.：-40℃ ----+125℃ b﹒Ambient temp.：100℃ max. a﹒Temp. rise ：20℃ max. e﹒Terminal pull strength：1.5 kg min. f﹒Rated current ：Current cause g﹒Resistance to solder heat：260℃.10 secs. h﹒Resistance to solvent：Per MIL-STD-202F AR-001A molding compound inductance drop within 10% requirements Temperature ( )℃ 100 217200 150 250245 Time ( seconds ) 100 150 60~150se c 150 ~ 200 / 60 ~ 180sec ℃ Max time above 217℃ ：60~150sec max. Max time above 245℃ ：20~40sec max. 200℃~250℃ Average Ramp-up Rate：3℃/second max. Temperature Rising Area Pe ak Temp：250℃ max. Reflow profile Preheat Area Reflow Area c﹒Terminal：Cu/Sn REF : 20070313-B Ⅲ﹒MATERIALS： a﹒Core：Ferrite DR core b﹒Wire ：Enamelled copper wire (class H) Ⅱ﹒SCHEMATIC DIAGRAM： Ⅰ﹒CONFIGURATION & DIMENSIONS： WOUND CHIP INDUCTOR Inductance code Marking NAME PROD. C B E A FF K1 d K2 1 11.8 （ PCB Pattern ） 1.4 ABC'S ITEM NO. ABC'S DWG NO. SPECIFICATION FOR APPROVAL 2.9±0.2 100 F : 0.6 E : 1.0±0.2 C : 2.2±0.2 B : 2.5±0.2 A : 3.2±0.4 +0.3-0 250 Peak Temperature： 250℃ Forc ed Coo lin g Area 6 / s e c o n d m a x . ℃ a c m/m m/m m/m m/m m/m PAGE: 1 20080131-D

1). □：Packaging information… A ：Bulk B：Taping Reel WOUND CHIP INDUCTOR SPECIFICATION FOR APPROVAL Ⅴ﹒ELECTRICAL CHARACTERISTICS： 2). "- ":Reference code□ □ □ CC3225270KL□-□□□ CC3225820KL□-□□□ CC3225680KL□-□□□ CC3225470KL□-□□□ CC3225330KL□-□□□ CC3225220KL□-□□□ CC3225150KL□-□□□ 33.00±10% 82.00±10% 68.00±10% 47.00±10% 27.00±10% 15.00±10% 22.00±10% REF : 20070313-B NAME PROD. CC32256R8ML□-□□□ CC32254R7ML□-□□□ CC32253R3ML□-□□□ CC32252R2ML□-□□□ CC32251R5ML□-□□□ CC32251R0ML□-□□□ DWG No. 1.50±20% 4.70±20% 6.80±20% 2.20±20% 3.30±20% ( µH ) Inductance 1.00±20% 2201.105282.5215 80.79620 2.52 2.52 2.52 2.52 2.52 2.52 2.52 7510.140 125 145 115 105 180 3.640 8.450 8.710 5.460 2.600 3.000 1.690 7.96 7.96 7.96 7.96 7.96 7.96 ( MHz ) Test Freq min. Q min. 100 ( MHz ) SRF ABC'S DWG NO. ABC'S ITEM NO. 320 280 400 480 580 770 max. ( mA )IDC 0.195 0.650 0.520 0.260 0.325 max. 0.156 ( Ω ) RDC PAGE: 220080131-D

@ Q VS. Frequency Response AR-001A 50Q 10 2-1 100 Frequency (MHz) 041 0 86 1R5M 100K 101K 330K @ Inductance VS. DC Superposition Characteristics SPECIFICATION FOR APPROVAL ABC'S ITEM NO. ABC'S DWG NO. Inductance (uH) 101 010 DC Current (mA) 325 1 0 7 2 523 7 1 0 3 1R5M 100K WOUND CHIP INDUCTOR Ⅵ﹒CURVE： 210 REF : 20070313-B NAME PROD. 330K 101K 23 7 51 0 3 PAGE: 3 20080131-D

168,0007,000 770 13 - 12 25.20 41 x 39 x 22 B ( 1 ) Configuration Ⅶ﹒PACKAGING INFORMATION： There is no differentiation or directions of polarity ( marking ) in the packaging method.※ WOUND CHIP INDUCTOR no component 200 m/m min. ( 2 ) Dimensions ( 3 ) Q'TY & G.W. Per package AR-001A CC3225 CC3225 CC3225 Series 07 - 08 13 - 12 Style A End REF : 20070813-C NAME PROD. User direction of feed Q'TY (pcs) 50,000 100,000 G.W. (gw) Inner : Reel 1,000 2,000 220 110 Q'TY (pcs) 07 - 08 07 - 08 Style 21±0.8 21±0.8 178 330 AB C 15.00 7.50 G.W. (Kg) Outer : Carton 41 x 39 x 22 41 x 39 x 22 Size (cm) D +010 +010 G -050 -050 N 12.5 18.4 T Unit:m/m Cover Tape D N Components 4 m/mP:4 m/m Leader 100 100 100 100 100 G Start 400 m/m min. 100 100 100 Trailer no component Embossed Carrier Carrier Tape Width : D※ ABC'S DWG NO. ABC'S ITEM NO. SPECIFICATION FOR APPROVAL 2.0±0.5 T PAGE: 4 20080131-D

[ anti-static ] [ anti-static ] 450 m/m 160 m/m Appendix code 2 : Package Appendix code 1 : Classification Type code Appendix code 2：Package Information Appendix code 1：Product Classification AR-001A 200 m/m Note： 2 package code "F" ： 200 m/m-0 End End 100 100 100 100 100 100 100 100 100 100 100 100 100 100 L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements T / R ( Reel package ) T / R ( Reel package ) Inner package T / R ( Reel package ) T / R ( Reel package ) T / R ( Reel package ) E F D B C AB a g Code 2000 1000 1000 7000 1000 2000 pcs pcs pcs pcs pcs pcs Inner package Q'TY WOUND CHIP INDUCTOR Ⅷ﹒DWGING NUMBER EXPRESSION： REF : 20080131-D C C NAME PROD. ABC'S DWG NO. ABC'S ITEM NO. 225 Tolerance code Dimension code Electrical code Reference code SPECIFICATION FOR APPROVAL Remark PAGE: 5

1﹒Applied the allowed DC current for mechanical damage mechanical damage 1﹒Inductors shall be not change more 2﹒Inductance shall more than ±20% 3﹒Q Shall not change shall be no evidence mechanical damage shall be no evidence After tset，Inductors After test，Inductors Shock test soldering heat Resistance to AR-001A than±5% Insulation resistance test ( Low frequency ) Vibration test rise test Temperature Withstanding Over load test voltage test of electrical and Mechanical performance test electrical and no evidence of

1000 MΩ min﹒

20 max.℃ a height of 1m onto 3cm wooden board Inductors shall be dropped 10 times from Time：10±1.0 sec. Temp：260±5℃ 4﹒Duration：2 hrs / X，Y，Z 2﹒Frequency：10 -- 55 -- 10 Hz / 1min.

100 VDC applied between inductor terminal

AC voltage of 1000VAC applied between inductors terminal and coating for 5 seconds current to inductor for a period of Applied 2 times of rated allowed DC 2﹒Temperature measure by digital 3﹒Direction：X，Y，Z 1﹒Amplitude：1.5 m/m 5 minutes surface thermometer 10 minutes and coating SPECIFICATION FOR APPROVAL WOUND CHIP INDUCTOR PROD. NAME Inductance L frequency SRF Self resonance Rated current IDC DC Resistance RDC Ⅸ﹒RELIABILITY TEST： Q characteristic list Refer to standard electrical Electrical performance test Test item Specification REF : 20070115-A □HP4291A with HP-16093A test fixture to initial value & temperature rise shall Inductance change shall be less than 10% Applied the current to coils，The □HP4194A with HP-16034E test fixture Test condition / Test method CH-502AC not be more than 20℃ ABC'S ITEM NO. ABC'S DWG NO. PAGE: 6 20080131-D

3﹒Load：Allowed DC current 2﹒Time：1000±12 hours 1﹒Temp：85±2℃ 2﹒Time：96±2 hours 1﹒Temp：85±2℃ 2﹒R.H.：90 -- 95% 4﹒Load：Allowed DC current 3﹒Time：1000±12 hours for 1 hour or more but not more than 2 hours , Measure the electrical and Unless otherwise specified , Allow the specimen to stand at room temperature 1﹒Temp：40±2℃ Room temp 2﹒Time：96±2 hours 1﹒Temp：-25±2℃ 3﹒Time：96±2 hours 2﹒R.H.：90 -- 95% 1﹒Temp：40±2℃ 15 mins evidence of short or mechanical performances open circuiting AR-001A Note： Humidity load life There shall be no damage not change more change more than ±20% 3﹒Q shall not than ±10% 2﹒Inductance shall electrical and no evidence of 1﹒Inductors shall be load life test High temperature Dry heat test Thermal shock test Temperature Humidity test characteristic Cold test Total：5 cycles mechanical -40 -- +125℃℃ 30 mins 30 mins +125±2℃ -40±2℃ Terminals in the axis direction for ABC'S DWG NO. ABC'S ITEM NO. MIL-STD-202F，Method 215D a melted solder bath at 240±5 for℃ After fluxing，Inductor shall be dipped in A 0.5kg load shall be applied to both SPECIFICATION FOR APPROVAL of marking change in be loosened or appearance or obliteration case deformation There shall be no covered with solder be at least 90% The terminal shall Terminal shall not WOUND CHIP INDUCTOR Climatic test Resistance to Solderability test solvent test strength-pull Terminal PROD. NAME test 5 seconds﹒ ruptured 1 minute﹒ REF : 20070115-A PAGE: 7 20080131-D

June 2, 1998; June 2, 1988. Reports: January 19, 1988: January 19, 1988: January 19, 1988: June 2, 1988; Ⅹ﹒UL CARD： WOUND CHIP INDUCTOR Marking：Dompany name/nateriel designation or marked designation and factory identification on package ok reel For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. IALAN DAMN SATU IANDA BAIK 28 750 BENTONG, PAHANG Polysol 155g See General Information preceding These Recognitions Polysol-N 180 Polysol 170 Polysol 180 Polysol 160 Polysol 155p ELEKTRISOLA (MALAYSLA) SDN BHD DARUL MAKMUR MALAYSIA Mtl Dsg Estersol 160 Amldester 200 Polysol-N 155 Polysol 155 Magnet Wire-Comporent OBMW2 AR-001A NAME PROD. REF : 20070115-A P160 Polyurechane 155____ MW-79 13013094V-00.84BK 130 0.84 0.3 6.4 3.1 6.4 BK BK BK BK BK 94V-0 94V-0 94V-0 94V-0 94V-0 130 130 130 130 130 R 130 130 130 130 130130 130 130 130 130 March 4, 1994 ____ Nylon ____ 0.79 0.79 0.79 ALL ALL ALL 94HB 94V-0 94HB PN180 P170 or G170 P180 Polyurechane Polyurechane Polyurechane 50 50 E59481 (S) MW-79 MW-79 ____ 156 155 180 ABC'S ITEM NO. ABC'S DWG NO. August 27, 1999 ____ ____ OC ____ Nylon ____ ____E180 Pg155 Pp155,Gp155 P155 PN155 A200 Mark Dsg Polyesterimide Polyurechane Polyurechane (solderable) Polyurechane Polyesterimide Polyurechane Coating Type BC E143312 MW-77 MW-28 MW-79 MW-79 MW-79 MW-79, MW-74 MW-80, Typ ANSI 180 100 130 155 130 155, 200 155, Class Temp SPECIFICATION FOR APPROVAL PAGE: 8 20080131-D