CC0201BR7BN YAGEO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 14
Technical content
Product Specification –November 24, 2016 V.15 DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General purpose Class 1, NP0
16 V TO 50 V
0.22 pF to 100 nF RoHS compliant & Halogen Free
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose This specification describes NP0 series chip capacitors with lead - free terminations.
APPLICATIONS
Consumer electronics for example - Tuners - Television receivers - All types of cameras Telecommunications Data processing
FEATURES
Supplied in tape on reel Nickel -barrier end termination RoHS complian t Halogen Free compliant ORDERING INFORMATION - GLOBAL PART NUMBER, PHYCOMP CTC & 12NC All part numbers are identified by the series, size, tolerance, TC material, packing style, voltage, process code, termination and capacitance value. YYAAGGEEOO BBRRAANNDD oorrddeerriinngg ccooddee GLOBAL PART NUMBER (PREFERRED ) CC XXXX X X NPO X BN XXX (1) SIZE – INCH BASED (METRIC) 0201 (0603) 0402 (1005) 0603 (1608) 0805 (2012) 1206 (3216) 1210 (3225) 1812 (4532) (2) TOLERANCE B = ± 0.1 pF C = ± 0.25 pF D = ± 0.5 pF F = ± 1% G = ± 2% J = ± 5% K = ± 10% (3) PACKING STYLE R = Paper/PE taping reel; Reel 7 inch K = Blister taping reel; Reel 7 inch P = Paper/PE taping reel; Reel 13 inch F = Blister taping reel; Reel 13 inch C = Bulk case (4) RATED VOLTAGE 7 = 16 V 8 = 25 V 9 = 50 V (5) CAPACITANCE VALUE 2 significant digits+number of zeros The 3rd digit signifies the multiplying factor, and letter R is decimal point Example: 121 = 12 x 101 = 120 pF
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose TYPE L1 (mm) W (mm) T (MM) L2 / L3 (mm) L4 (mm) min. max. min. 0201 0.6 ± 0.03 0.3 ± 0.03 Refer to table 2 to 5 0.10 0.20 0.20 0.25 0.75 0.55 0.25 0.75 1.40 NOTE 1. Dimension for size 0805 and 1206, C ≤ 1 nF 2. Dimension for size 0805 and 1206, C > 1 nF Table 1 For outlines see fig. 2 DIMENSION OOUUTTLLIINNEESS For dimension see Table 1 Fig. 2 Surface mounted multilayer ceramic c apacitor dimension CONSTRUCTION The capacitor consists of a rectangular block of ceramic dielectric in which a number of interleaved metal electrodes are contained. This structure gives rise to a hi gh capacitance per unit volume. The inner electrodes are connected to the two end terminations and finally covered with a layer of plated tin (NiSn). The terminations are lead -free. A cross section of the structure is shown in Fig.1. Fig. 1 Surface mounted multilayer ceramic capacitor co nstruction
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose CAPACITANCE RANGE & THICKNESS FOR NP0 Table 2 Sizes from 0201 to 0603 CAP. 0201 0402 0603
25 V 50 V 16 V 25 V 50 V 16 V 25 V 50 V
- Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-12 series is on request
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose CAP. 0201 0402 0603 4.7 nF 5.6 nF 6.8 nF 8.2 nF 12 nF 15 nF 18 nF 22 nF 33 nF NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-12 series is on request Table 3 Sizes from 0201 to 0603 (continued) CAPACITANCE RANGE & THICKNESS FOR NP0
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose CAPACITANCE RANGE & THICKNESS FOR NP0 Table 4 Sizes from 0805 to 1812 CAP. 0805 1206 1210 1812
16 V 25 V 50 V 16 V 25 V 50 V 25 V 50 V 50 V
0.22 pF NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-12 series is on request
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose CAP. 0805 1206 1210 1812 10 nF 0.85± 0.1 1.25± 0.2 0.85± 0.1 1.25± 0.2 0.85± 0.1 56 nF 82 nF NOTE 1. Values in shaded cells indicate thickness class in mm 2. Capacitance value of non E-12 series is on request Table 5 Sizes from 0805 to 1812 (continued) CAPACITANCE RANGE & THICKNESS FOR NP0
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose THICKNESS CLASSES AND PACKING QUANTITY SIZE CODE THICKNESS CLASSIFICATION TAPE WIDTH QUANTITY PER REEL Ø 180 MM / 7 INCH Ø 330 MM / 13 INCH QUANTITY PER BULK CASE Paper Blister Paper Blister 0402 0.5 ± 0.05 mm 8 mm 10,000 --- 50,000 --- 50,000 0603 0.8 ± 0.1 mm 8 mm 4,000 --- 15,000 --- 15,000 0805 0.85 ± 0.1 mm 8 mm 4,000 --- 15,000 --- 8,000 1206 1210 1,000 --- --- --- 500 --- --- --- 1808 1812
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose
ELECTRICAL CHARACTERISTICS
NNPP00 DDIIEELLEECCTTRRIICC CCAAPPAACCIITTOORRSS;; NNIISSNN TTEERRMMIINNAATTIIOONNSS Unless otherwise stated all electrical values apply at an ambient temperature of 20±1 °C, an atmospheric pressure of 86 to 106 kPa, and a relative humidity of 63 to 67%. DESCRIPTION VALUE Capacitance range 0.22 pF to 100 nF Capacitance tolerance C < 10 pF ± 0.1 pF, ± 0.25 pF, ± 0.5 pF Dissipation factor (D.F.) C < 30 pF ≤ 1 / ( 400 + 20C ) C ≥ 30 pF ≤ 0.1 % Insulation resistance after 1 minute at Ur (DC) Rins ≥ 10 GΩ or Rins × Cr ≥ 500 seconds whichever is less Maximum capacitance change as a function of temperature (temperature characteristic/coefficient): ± 30 ppm/°C Operating temperature range: –55 °C to +125 °C Table 7 Fig. 4 Typical capacitance change with respect to the capacitance at 1 V as a function of DC voltage Fig. 3 Typical temperature coefficient as a function of temperature Sample limits (broken lines). Requirement levels (dotted lines)
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose Fig. 5 Typical tan δ as a function of temperature SOLDERING RECOMMENDATION Table 8 SOLDERING METHOD SIZE 0201 0402 0603 0805 1206 ≥ 1210 Reflow Reflow only ≥ 0.1 µF ≥ 1.0 µF ≥ 2.2 µF ≥ 4.7 µF Reflow only Reflow/Wave --- < 0.1 µF < 1.0 µF < 2.2 µF < 4.7 µF ---
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose Table 9 Test procedures and requirements TEST TEST METHOD PROCEDURE REQUIREMENTS Mounting IEC 60384-
4.3 The capacitors may be mounted on printed-circuit boards
4.4 Any applicable method using × 10 magnification In accordance with specification
Capacitance 4.5.1 Class 1: f = 1 MHz for C ≤ 1 nF, measuring at voltage 1 Vrms at 20 °C f = 1 KHz for C > 1 nF, measuring at voltage 1 Vrms at 20 °C Within specified tolerance Dissipation factor (D.F.)
4.5.2 Class 1:
f = 1 MHz for C ≤ 1 nF , measuring at voltage 1 Vrms at 20 °C f = 1 KHz for C > 1 nF, measuring at voltage 1 Vrms at 20 °C In accordance with specification Insulation resistance
4.5.3 At Ur (DC) for 1 minute In accordance with specification
4.6 Capacitance shall be measured by the steps shown in the
following table. The capacitance change should be measured after 5 min at each specified temperature stage. Step Temperature(℃) a 25±2 b Lower temperature± 3℃ c 25± 2 d Upper Temperature± 2℃ e 25± 2 (1) Class I Temperature Coefficient shall be calculated from the formula as below Temp, Coefficient = 610T xC1 C1-C2 Δ [ppm/℃] C1: Capacitance at step c C2: Capacitance at 125℃ (2) Class II Capacitance Change shall be calculated from the formula as below ∆C = C1-C2 x 100% C1: Capacitance at step c C2: Capacitance at step b or d <General purpose series> Class1: ∆ C/C: ± 30ppm Class2: X7R: ∆ C/C: ± 15% <High Capacitance series> Class2: X7R/X5R: ∆ C/C: ±15%
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose TEST TEST METHOD PROCEDURE REQUIREMENTS Adhesion 4.7 A force applied for 10 seconds to the line joining the terminations and in a plane parallel to the substrate Force size ≥ 0603: 5N size = 0402: 2.5N size = 0201: 1N Bond strength of plating on end face 4.8 Mounting in accordance with IEC 60384-22 paragraph 4.3 No visible damage Conditions: bending 1 mm at a rate of 1 mm/s, radius jig 5 mm <General purpose series> ∆C/C Class 1: NP0: within ± 1% or 0.5 pF whichever is greater Resistance to soldering heat IEC 60384- 4.9 Precondition: 150 +0/–10 °C for 1 hour, then keep for 24 ± 1 hours at room temperature Preheating: for size ≤ 1206: 120 °C to 150 °C for 1 minute Preheating: for size >1206: 100 °C to 120 °C for 1 minute and 170 °C to 200 °C for 1 minute Solder bath temperature: 260 ± 5 °C Dipping time: 10 ± 0.5 seconds Recovery time: 24 ± 2 hours Dissolution of the end face plating shall not exceed 25% of the length of the edge concerned <General purpose series> ∆C/C Class 1: NP0: within ± 0.5% or 0.5 pF whichever is greater D.F. within initial specified value Rins within initial specified value Solderability 4.10 Preheated the temperature of 80 °C to 140 °C and maintained for 30 seconds to 60 seconds. 1. Temperature: 235± 5°C / Dipping time: 2 ± 0.5 s 2. Temperature: 245± 5°C / Dipping time: 3 ± 0.5 s (lead free)Depth of immersion: 10mm The solder should cover over 95% of the critical area of each termination Rapid change of temperature
4.11 Preconditioning;
150 +0/–10 °C for 1 hour, then keep for 24 ± 1 hours at room temperature 5 cycles with following detail: 30 minutes at lower category temperature 30 minutes at upper category temperature Recovery time 24 ± 2 hours No visual damage <General purpose series> ∆C/C Class 1: NP0: within ± 1% or 1 pF whichever is greater D.F. meet initial specified value Rins meet initial specified value
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose TEST TEST METHOD PROCEDURE REQUIREMENTS Damp heat with Ur load IEC 60384- 4.13 1. Preconditioning, class 2 only: 150 +0/-10 °C /1 hour, then keep for 24 ± 1 hour at room temp 2. Initial measure: Spec: refer to initial spec C, D, IR 3. Damp heat test: 500 ± 12 hours at 40 ± 2 °C; 90 to 95% R.H. 1.0 Ur applied 4. Recovery: Class 1: 6 to 24 hours 5. Final measure: C, D, IR P.S. If the capacitance value is less than the minimum value permitted, then after the other measurements have been made the capacitor shall be preconditioned according to “IEC 60384 4.1” and then the requirement shall be met. No visual damage after recovery <General purpose series> ∆C/C Class 1: NP0: within ± 2% or 1 pF whichever is greater D.F. Class 1: NP0: ≤ 2 x specified value Rins Class 1: NP0: ≥ 2,500 MΩ or Rins x Cr ≥ 25s whichever is less Endurance 4.14 1. Preconditioning, class 2 only: 150 +0/-10 °C /1 hour, then keep for 24 ± 1 hour at room temp 2. Initial measure: Spec: refer to initial spec C, D, IR 3. Endurance test: Temperature: NP0: 125 °C Specified stress voltage applied for 1,000 hours: Applied 2.0 x Ur for general product. 4. Recovery time: 24 ± 2 hours 5. Final measure: C, D, IR P.S. If the capacitance value is less than the minimum value permitted, then after the other measurements have been made the capacitor shall be preconditioned according to “IEC 60384 4.1” and then the requirement shall be met. No visual damage <General purpose series> ∆C/C Class1: NP0: within ± 2% or 1 pF whichever is greater D.F. Class1: NP0: ≤ 2 x specified value Rins Class1: NP0: ≥ 4,000 MΩ or Rins x Cr ≥ 40s whichever is less Voltage proof IEC 60384-1 4.6 Specified stress voltage applied for 1 minute Ur ≤ 100 V: series applied 2.5 Ur 100 V < Ur ≤ 200 V series applied (1.5 Ur + 100) 200 V < Ur ≤ 500 V series applied (1.3 Ur + 100) Ur > 500 V: 1.3 Ur I: 7.5 mA No breakdown or flashover
www.yageo.com Nov. 24, 2016 V.15 Surface-Mount Ceramic Multilayer Capacitors Product specification General Purpose
REVISION HISTORY
DESCRIPTION
Version 15 Nov. 21, 2016 - - Product range updated Version 14 Jul. 22, 2016 - - Add 0805/8.2nF and 10nF/ 16V to 50V, T=1.25mm Version 13 May. 16, 2016 - - Product range updated Version 12 Feb. 16, 2016 - - Product range updated Version 11 Sep. 11, 2014 - - Product range updated Version 10 Feb. 18, 2014 - - Product range updated Version 9 Jun. 17, 2013 - - Product range updated Version 8 Aug 05, 2011 - - Dimension updated Version 7 Jun 14, 2011 - - Size1210 T=1.0mm SPQ added - Dimension updated Version 6 Jan 06, 2011 - - Dimension updated Version 5 Dec 29, 2010 - - Dimension updated Version 4 Nov 23, 2010 - - Dimension updated Version 3 Apr 20, 2010 - - The statement of "Halogen Free" on the cover added - Dimension updated Version 2 Oct 26, 2009 - - Typo updated Version 1 Jun 02, 2009 - - 12NC code updated Version 0 Apr 15, 2009 - - New datasheet for general purpose NP0 series with RoHS compliant - Replace the "16V to 50V" part of pdf files: NP0_16V_7, NP0_16V-to- 100V_6, NP0_25V_7, NP0_50-to-500V_11 - Combine 0201 from pdf files: UP-NP0X5RX7RY5V_0201_6.3-to-50V_2 and UY-NPOX5RX7RY5V_0201_6.3-to-50V_2 - Define global part number - Description of "Halogen Free compliant" added - Test method and procedure updated