CBR122 ETC2 | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 1
Technical content
Ths But ana epsocaled donumants and the conaioaa __ rr 7 information are the confidential property of ELECT INSTALLATION INSTRUCTIONS [_______vescneron SSS CABLE SPECIALISTS: Dinclosure off ond/or repraduetion [ sex [zone [ree] [eT rnc | of, ll or port thereof or manufacture of any part from | 1, BEGIN BY CUTTING THE CABLE OFF SQUARE. [arii[ N/cl New RELEASE. [474796 | JeH | Iniotmefion contained om this prmt at apecliesy per [ease] Ta [ See Eon 4456 ]619 36] v0] D_ [fore ECMONE CABLE SPECIALISTS in wring is ——t [sao] [8 | see cong 6169 sel wet | 2. WHEN USING aurouanc staPPNG EquPwenr, stm came [152741 lc | see cong 15274 etches ES Bone AS SHOWN STARTING WMH LI AND ENDING WITH L3. TAKE 8. SLIDE THE BODY OF THE CONNECTOR OVER THE END OF THE CABLE UNTIL THE 152 CARE NOT TO NICK THE CONDUCTORS WHILE STRIPPING THE NOTCH IN THE CONTACT SEATS WITH THE DIELECTRIC RIOGE INSIDE THE C4 a OIELECTRIC AND JACKET. IF AUTOMATIC STRIPPING EQUIPMENT IS CONNECTOR BODY. eerel E F NOT AVWLASLE, STA OMY Li AND LS AND TRM! Excess = 87 bso (eal /| ORUD AT STEP 10. 3 8 game 1.150 ae ELITE) <___ = ee u = a9 SONTACT WS = 62 <{[ TI LA 3. SUDE THE FERRULE AND ADHESIVE SHRINK TuBING /2\\ Cc OVER THE END OF THE CABLE, fi) c sions Ay =] =n et "SPECIFICATIONS 10. SUDE THE FERRULE UP OVER THE SHIELDS AND AGAINST THE CONNECTOR 4. SOLDER THE CONTACT ONTO THE CENTER CONDUCTOR, PER BODY. TRIM AWAY ANY EXCESS BRAID. CRIMP THE FERRULE ONCE, NEXT ELECTIGAL STD TO THE BODY, USING THE M22520/5~47 DIE IN A M22520/5~01 IMPEDANCE: 50 OHMS NOMINAL MIL-STD~2000, USING 63Sn/37Pb SOLDER OR CRIMP PREOUENCY RANGES Otome wit _M22520/5~57 Die (8 HEX). ENSURE THE CONTACT 1S TOOL FRAME. APPLY ADHESIVE HEAT SHRINK. /}\\ FREQUENCY RANGE: 0-4 Ghz DUTTED AGAINST THE COOKE ORLECTIIG GLEAN far ox —HNZ INSERTION LOSS: .1dB MAXIMUM DC TO 2GHz RESIDUES USING AN RUTE FLUX Cl eR. poued WORKING VOLTAGE: 500 VRMS © SEA LEVEL NOTES iNet DIELECTIG WIHSTANOING: 1800 VRS © SEA LEVEL <[ |e ALL OMENSIONS ARE IY WeHES, ie INSULATION RESISTANCE: 5000 MEGOHMS MINIMUM - 7 = Foo ete be 5. USING TWEEZERS, FOLD THE OUTER BRAID BACK OVER MECHANICAL Te Gate Rene Cane oe aR ERD BACK OVER & ENSURE HEAT SHRINK IS INSTALLED PRIOR TO CRIMPING CONNECTOR. CONNECTOR INTERFACE DIMENSION PER MiL-STO-348A ADHESIVE HEAT SHRINK SHOULD GE APPLIED IN ACCORDANCE WiTH FIGURE 301-1 B | emumnaiion Srme: wWWeR CONTACT-SOLOER oR CRIMP <_{ |r CS WORK INSTRUGTON W007, CONTAGT Ecs FOR a copy oF mms wore | B uote aevenniony SUTEE, CONIAGT-FERFULE” CRIMP INSTRUCTION. ENVIRONMENTAL 6. SUCE THE ALUMINUM/POLYESTER FOIL LENGTHWISE ABOUT ZX CONNECTOR DIMENSIONS ARE FOR REFERENCE ONLY. . . EVERY 1/8". GENTLY ROTATE PIN TO SEPARATE THE FLAT FOIL TEVPERATURE FATWG: 68 TO 4165 6 Bao AN ALUMNUM/POLYESTER FOR. FROM THE DELECTRG. DELETED Aged . 7 USING TWEEZERS, FOLD BACK ALUMINUM/POLYESTER FOIL 6. DELETED. SHOCK: MIL-ST0~202, METHOD 213, COND. 1 SENG TWEEZERS, FOLD THERMAL SHOCK: MIL-STD-202, METHOD 107, CONO. 8 7. eer peti ‘SHOW CONNECTOR ron oa Ot fee ae CORROSION: MIL-STD=202, METHOD 101, COND. 8 WHEN INSTALLING THIS CONNECTOR ON 421201 y MOSTURE RESISTANCE. M~STD~202" METHOD 106 To} fares 2 SHIELOS Wich SHOULD GE FOLDED SICK AS SHOW IN STEP 6 MATERIALS: BODY: BRASS PER GO-8-626 ALL LENGTHS IN INCHES| © MB ELECTRONIC CaBle SPECIAUSTS CABLE CONTACT: BERYLUUM COPPER PER CQ—C~530 HIELOS. WUCH WEAVE AS PO [_wrroms | ors A CENTER CONTACT: BRASS PER 00-8-626 NOTE: DO _NOT UNRAVEL DIELECTRIC WHEN PULLING Pa pennemis/ayoel CUSTOMER SPECIFICATION A OUTER CONTACT: BERYLLIUM COPPER PER QQ-C-530 GACK INNER SHIELD. aT BNC RIGHT ANGLE PLUG FOR ECS CABLE DIELECTRIC: TEFLON PER L-P—403 om Pie TAvaennem [6/4/96] 311201, 421201 GASKET: SILICONE RUBBER PER 22-R-765, oe a i PE oo ox oa aes Paes bara 566197 CBR122 B00Y, FERRULE: BRIGHT NICKEL PER CO-N-290 CENTER CONTACT: COLD PER MiL~G~45204 a A ra Ee 4 3 2 1