CBM2093 CHIPSBANK | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 15
Technical content
Datasheet sections
- 1 DESCRIPTION
- 2 FEATURES
- 3 BLOCK DIAGRAM
- 4 PIN ASSIGNMENT
- 4.1 TQFP48 (TOP SIDE)
- 5 PIN DESCRIPTION
- 6 ELECTRICAL CHARACTERISTICS
- 6.1 ABSOLUTE MAXIMUM RATINGS
- 6.2 RECOMMENDED OPERATING CONDITIONS
- 6.3 STATIC CHARACTERISTICS
- 6.4 DYNAMIC CHARACTERISTICS
- 7 MECHANICAL DIMENSIONS
- 8 COPYRIGHT NOTICE
C B M 2 0 9 3 D a t a s h e e t - 1 - 0 5 / 1 2 / 2 0 0 9 CBM2093 USB 2.0 Flash Disk Controller Datasheet Rev 1.0
C B M 2 0 9 3 D a t a s h e e t - 2 - 0 5 / 1 2 / 2 0 0 9
Revision History
2009-05-12 1.0 Initial release
C B M 2 0 9 3 D a t a s h e e t - 4 - 0 5 / 1 2 / 2 0 0 9
1 Description
Fastest & Securest USB 2.0 Flash Disk Controller with dedicated 32-bit microprocessor The CBM2093 is the USB 2.0 Flash Disk controller with the fastest transfer speed on the market. CBM2093 can reach theoretical flash access speed limit of over 32MByte/s for read and 20MByte/s for write. The on-the-fly ECC engine is capable of correcting up to 8/15bits per 512 bytes page . For data security, CBM2093 is designed with both hardware and software data protection technology to prevent data corruption even if it is powered off or unplugged during data transfer. The CBM2093 supports all 8 /16 bit BUS wide NAND flash memory available in the market. New flash can be supported by software re-configuration. The CBM2093 has both a) 5V to 3.3V LDO and b) power on reset circuits integrated. Thus greatly reduced BOM cost and eased layout burden. The CBM2093 runs smoothly with all available hosts and PC platforms. Complied with USB specification rev. 2.0, the CBM2093 can be supported without additional driver under Win XP, Win 2000, Windows Me, Mac OS and Linux OS. With device driver installed, it can support Win 98/98SE as well. Comprehensive applications, such as PC boot up, disk partitions, password check for security disk, are available as part of our standard mass production software package. The CBM2093 is available in 48-pin TQFP and 64-pin LQFP package, which are thinnest and smallest on the market. The 48-pin CBM2093 supports up to 4 flash chips and the 64-pin CBM2093 supports up to 8 flash chips. Customers can choose different packages to meet their design requirement.
2 Features
USB Interface High-speed USB 2.0 interface; Fastest data transfer rate on the market Dual-channel mode: 32MB/s for Read, 20MB/s for Write Single-channel mode: 26MB/s for Read, 20MB/s for Write Fastest file copy rate on the market. On-the-fly ECC built-in Hardware enhances reliability ECC for SLC NAND flash: 8 bit per page (1 page = 512 bytes) ECC for MLC NAND flash: 8/15 bit per page Special wear leveling algorithm to improve the flash life-time Hardware & Software Data Protection Technology Prevent data corruption even if it is powered off or unplugged during data transfer.
C B M 2 0 9 3 D a t a s h e e t - 5 - 0 5 / 1 2 / 2 0 0 9 NAND, SLC/MLC Flash Interface Support 4k page flash parallel mode. Support 8-bit and 16-bit Samsung SLC and MLC NAND flash. Support 8-bit and 16-bit Toshiba SLC and MLC NAND flash. Support 8-bit and 16-bit Hynix SLC and MLC NAND flash. Support 8-bit and 16-bit Micron/Intel SLC and MLC NAND flash. Support 8-bit and 16-bit ST/Numony SLC and MLC NAND flash. Support 8-bit and 16-bit Infineon SLC and MLC NAND flash. Support 8-bit and 16-bit Sandisk SLC and MLC NAND flash. Support PowerChip SLC & MLC Nand Flash Support Spansion 3.3V MirrorBit-Quad Flash Support SMIC Double Density Flash Support Actrans Nand Flash Software configuration to support various new flash memories Supports up to 8 flash chips. Proprietary 32-bit CISC microprocessor feature Proprietary 32-bit CISC processor for USB protocol processing and flash access. Single cycle instruction period Integrated 5v to 3.3v voltage regulator Disk partitions and password check for security disk available PC boot up as USB Zip Disk, USB Hard Disk or USB CDROM Auto run function Low power dissipation Operating current 50mA (Bus power compatible) Build-in LDO Output maximum current up to 300mA Leading 0.18um CMOS technology 48-pin TQFP /64-pin LQFP package 48-pin CBM2093 supports up to 4 Flash Chips Windows, Mac and Linux compatible
C B M 2 0 9 3 D a t a s h e e t - 6 - 0 5 / 1 2 / 2 0 0 9
3 Block Diagram
C B M 2 0 9 3 D a t a s h e e t - 7 - 0 5 / 1 2 / 2 0 0 9
4 Pin Assignment
4.1 TQFP48 (Top Side)
C B M 2 0 9 3 D a t a s h e e t - 8 - 0 5 / 1 2 / 2 0 0 9
5 Pin Description
Brief CBM2093 pin functions are shown in the following tables. I: Input signal O: Output signal I/O: Bi-direction signal PWR: Power signal GND: Ground signal PU: pull up PD: pull down CBM2093 TQFP48 Pin Description TQFP48 Pin No. Pin Name Type Description
1 VDD50 PWR Regulator5V Power Input
2 VDD33 PWR Regulator 3.3V Power OUT 3 VDD18_OUT PWR Regulator 1.8V Out 4 VDD18_IN PWR CORE 1.8V in
5 REXT I Connect External Resister for current reference
6 VDD33 PWR Padring 3.3V Power
7 DP I/O USB Data D+
8 DM I/O USB Data D-
9 VSS GND Padring 3.3V / Logic 1.8V Ground
10 XI I Crystal Input (12 MHz)
11 XO O Crystal Output
12 VSSU GND Analog 1.8V Ground 13 VDDU PWR Analog 1.8V Power
14 TEST_MODE I
When high , test mode When low , normal mode
15 FDATA1_7
Group 1 Flash Data Bus - bit 7 General I/O port 15
C B M 2 0 9 3 D a t a s h e e t - 9 - 0 5 / 1 2 / 2 0 0 9 When select spi mode ,as spi chip select . (configure as GPIO and clear pin_64( detail in spi_ctl[13] .when select master mode , configure output , otherwise, configure as input.).
16 FDATA1_6
Group 1 Flash Data Bus - bit 6 General I/O port 14 When select spi mode, as clock out support ligh-tun sensor (configure as GPIO and clear pin_64( detail in spi_ctl[13] .when select ligh-tun mode , configure output). 17 VSS GND Padring 3.3V / Logic 1.8V Ground
18 FDATA1_5
Group 1 Flash Data Bus - bit 5 General I/O port 13
19 FDATA1_4
Group 1 Flash Data Bus - bit 4 General I/O port 12
20 FDATA1_3
Group 1 Flash Data Bus - bit 3 General I/O port 11
21 FDATA1_2
Group 1 Flash Data Bus - bit 2 General I/O port 10
22 FDATA1_1
Group 1 Flash Data Bus - bit 1 General I/O port 9
23 FDATA1_0
Group 1 Flash Data Bus - bit 0 General I/O port 8 24 X_LED I/O When TEST_MODE =1, as scan clock input. When TEST_MODE =0, as LED Indication
25 FWRN O Group Flash Write Enable (active low)
26 FALE
O Group Flash Address Latch Enable
27 WP I Write Protect Switch Input
28 FCLE
O Group Flash Command Latch Enable 29 VDD33 PWR Padring 3.3V Power
30 CLKOFF I
PD Clock input switch. CLK_OFF=1, select external test clock.
31 FCEN0 O Flash Chip Enable - Chip 0 (active low)
32 FRDN O Group Flash Read Enable (active low)
33 FRB1
/INTR I Group Flash Ready_Busy 1, when select flash_rb1 mode, as Group Flash Ready_Busy1 signal input(detail in soft_flag [25]). 2, when select intr mode, as external interrupt input signal(detail in soft_flag [25]). 34 /SCK(I2c) FCEN3 O 1, When select test-mode, as scan-chain output 2, When select i2c , as sck 3, When select chip select2/3 mode, as CE3 output
35 FCEN2
1, When select test_mode, As scan-chain input 2, when select chip select2/3 mode, as CE2 output .(active when disable test_mode)
CBM2093 Datasheet - 10 - 05/12/2009 X_CLK_OUT /FCEN1 I/O PU 1, When select clock input mode (1), X_CLK_OFF=1, as external input test clock. 2, When select chip select1 mode or spi master mode, as output. ( only active when X_CLK_OFF =0 or de-slect spi slve mode) (1), select chip select1 mode (detail in soft_flag [28]/[25]), as CE1 output (2), otherwise, as normal clock_out ,which defined at config_r[20].
37 FRB0 I Group Flash Ready_Busy0
38 FDATA0_0
Group 0 Flash Data Bus - bit 0 General I/O port 0
39 FDATA0_1
Group 0 Flash Data Bus - bit 1 General I/O port 1
40 FDATA0_2
Group 0 Flash Data Bus - bit 2 General I/O port 2
41 FDATA0_3
Group 0 Flash Data Bus - bit 3 General I/O port 3
42 FDATA0_4
Group 0 Flash Data Bus - bit 4 General I/O port 4
43 FDATA0_5
Group 0 Flash Data Bus - bit 5 General I/O port 5
44 FDATA0_6
Group 0 Flash Data Bus - bit 6 General I/O port 6
45 FDATA0_7
Group 0 Flash Data Bus - bit 7 General I/O port 7
46 RST_OUT O
Chip reset output/ External device reset signal Low active pulse output Should connect with RESET pad
47 RESET I Reset Sign (active low)
48 VSSA GND Analog 3.3V Ground
C B M 2 0 9 3 D a t a s h e e t - 1 1 - 0 5 / 1 2 / 2 0 0 9
6 Electrical Characteristics
6.1 Absolute maximum ratings
In accordance with the Absolute Maximum Rating System (IEC 60134). symbol parameter conditions min max unit VDD33 analog supply voltage -0.5 5.5 v VDD18 digital supply voltage -0.5 4.5 v VDD50 input voltage -0.5 5.5 v DP , DM and GND pins -4000 +4000 Vesd electrostatic discharge voltage[1] ILI <
1 A other pins -2000 +2000
v Tstg storage temperature -40 +125 \¥ [1] Equivalent to discharging a 100 pF capacitor via a 1.5 k resistor (Human Body \ Model).
6.2 Recommended operating conditions
symbol Parameter conditions min Typ max Unit VDD33 analog supply voltage 3.0 3.3 3.6 V VDD18 digital supply voltage 1.62 1.8 1.98 V VDD50 input voltage 4.5 5 5.5 V Low/Full speed 0 3.3 3.6 V VI(AI/O) input voltage on analog I/O pins DP DM High speed 0 400 - mV Tamb ambient temperature 0 - +70 ¥
6.3 Static characteristics
All parameters are measured at VCCA = VCCD = 3.0 to 3.6 V; VAGND = VDGND = 0 V; symbol Parameter Conditions min Type max Unit Full-speed transmitting and receiving; - 29.5 - ICC operating supply current high-speed transmitting and receiving - 50 mA ICC(susp) suspend supply current in suspend mode - 500 uA \`
CBM2093 Datasheet - 12 - 05/12/2009
6.4 Dynamic characteristics
All parameters are measured at VCCA = VCCD = 3.0 to 3.6 V; VAGND = VDGND = 0 V; symbol Parameter conditions min Typ max Unit Ts(FDATA*) FDATA* setup time relative to rising FWRN* edge Configured by firmware 8 33 75 ns Th(FDATA*) FDATA* hold time relative to falling FWRN* edge Configured by firmware 8 33 75 ns Ts (FCLE*) FCLE* setup time relative to falling FWRN* edge Configured by firmware 8 16 25 ns Th (FCLE*) FCLE* hold time relative to rising FWRN* edge Configured by firmware 10 16 75 ns Ts (FALE*) FALE* setup time relative to falling FWRN* edge Configured by firmware 8 16 25 ns Th (FALE*) FALE* hold time relative to rising FWRN* edge Configured by firmware 10 16 75 ns Ts (FCEN*) FCEN* setup time relative to falling FWRN* edge Configured by firmware - 99 ns Tpw (FWRN*) FWRN* Pulse Width Configured by firmware 8 33 75 ns Thh (FWRN*) FWRN* high hold time Configured by firmware 8 33 75 ns Ta(FDATA*) FDATA* access time relative to falling FRDN* edge -5 0 5 ns Tpw (FRDN*) FWRN* Pulse Width Configured by firmware 8 33 75 ns Thh (FRDN*) FWRN* high hold time Configured by firmware 8 33 75 ns Timing diagram for Writing of Data
CBM2093 Datasheet - 13 - 05/12/2009 Timing diagram for Reading of Data
CBM2093 Datasheet - 14 - 05/12/2009
7 Mechanical Dimensions
7.1 48-Pin CBM2093 Pack age Outline Dimension
CBM2093 Datasheet - 15 - 05/12/2009
8 Copyright Notice
Copyright by Chipsbank Technologies (Shenzhen) Co. Ltd. All Rights Reserved. Right to make changes — Chipsbank Technologies (Shenzhen) Co., Ltd reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. The information contained in this manual is provided for the general use by our customers. Our customers should be aware that the personal computer field is the subject of many patents. Our customers should ensure that they take appropriate action so that their use of our products does not infringe upon any patents. It is the policy of Chipsbank Technologies (Shenzhen) Co., Ltd. to respect the valid patent rights of third parties and not to infringe upon or assist others to infringe upon such rights. This manual is copyrighted by Chipsbank Technologies (Shenzhen) Co., Ltd. You may not reproduce, transmit, transcribe, store in a retrieval system, or translate into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise, any part of this publication without the expressly written permission from Chipsbank Technologies (Shenzhen) Co.,Ltd